Search Results (4)

The development of 3D porous nanocarbon composites has improved the performance of piezoresistive sensors. However, the functionalization and surface distribution of nanocarbon may limit conductivity and mechanical stability. In this study, a mechanochemical approach was developed to create an elastomeric/CNTs 3D porous nanocomposite. By changing parameters such as CNT length and polymer amount, different composites with improved piezoresistive properties can be produced for wearables or fluidic devices. The material can withstand compressive stress up to 150 Kpa and has a sensitivity of up to 330 Kpa⁻¹ and a limit of detection of 0.2 Pa and 50 nm for pressure and extension, respectively. Full article

Biomass-derived three-dimensional (3D) porous nanocarbons have attracted much attention due to their high surface area, permeability, electrical conductivity, and renewability, which are beneficial for various electronic applications, including energy storage. Cellulose, the most abundant and renewable carbohydrate polymer on earth, is a promising precursor to fabricate 3D porous nanocarbons by pyrolysis. However, the pyrolysis of cellulosic materials inevitably causes drastic carbon loss and volume shrinkage. Thus, polydopamine doping prior to the pyrolysis of cellulose nanofiber paper is proposed to fabricate the 3D porous nanocarbons with improved yield and volume retention. Our results show that a small amount of polydopamine (4.3 wt%) improves carbon yield and volume retention after pyrolysis at 700 °C from 16.8 to 26.4% and 15.0 to 19.6%, respectively. The pyrolyzed polydopamine-doped cellulose nanofiber paper has a larger specific surface area and electrical conductivity than cellulose nanofiber paper that without polydopamine. Owing to these features, it also affords a good specific capacitance up to 200 F g⁻¹ as a supercapacitor electrode, which is higher than the recently reported cellulose-derived nanocarbons. This method provides a pathway for the effective fabrication of high-performance cellulose-derived 3D porous nanocarbons. Full article

Capacitive deionization (CDI) based on ion electrosorption has recently emerged as a promising desalination technology due to its low energy consumption and environmental friendliness compared to conventional purification technologies. Carbon-based materials, including activated carbon (AC), carbon aerogel, carbon cloth, and carbon fiber, have been mostly used in CDI electrodes due their high surface area, electrochemical stability, and abundance. However, the low electrical conductivity and non-regular pore shape and size distribution of carbon-based electrodes limits the maximization of the salt removal performance of a CDI desalination system using such electrodes. Metal-organic frameworks (MOFs) are novel porous materials with periodic three-dimensional structures consisting of metal center and organic ligands. MOFs have received substantial attention due to their high surface area, adjustable pore size, periodical unsaturated pores of metal center, and high thermal and chemical stabilities. In this study, we have synthesized ZIF-67 using CNTs as a substrate to fully utilize the unique advantages of both MOF and nanocarbon materials. Such synthesis of ZIF-67 carbon nanostructures was confirmed by TEM, SEM, and XRD. The results showed that the 3D-connected ZIF-67 nanostructures bridging by CNTs were successfully prepared. We applied this nanostructured ZIF-67@CNT to CDI electrodes for desalination. We found that the salt removal performance was significantly enhanced by 88% for 30% ZIF-67@CNTs-included electrodes as compared with pristine AC electrodes. This increase in salt removal behavior was analyzed by electrochemical analysis such as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) measurements, and the results indicate reduced electrical impedance and enhanced electrode capacitance in the presence of ZIF-67@CNTs. Full article

The oxygen reduction reaction (ORR) at the cathode is a fundamental process and functions a pivotal role in fuel cells and metal–air batteries. However, the electrochemical performance of these technologies has been still challenged by the high cost, scarcity, and insufficient durability of the traditional Pt-based ORR electrocatalysts. Heteroatom-doped nanocarbon electrocatalysts with competitive activity, enhanced durability, and acceptable cost, have recently attracted increasing interest and hold great promise as substitute for precious-metal catalysts (e.g., Pt and Pt-based materials). More importantly, three-dimensional (3D) porous architecture appears to be necessary for achieving high catalytic ORR activity by providing high specific surface areas with more exposed active sites and large pore volumes for efficient mass transport of reactants to the electrocatalysts. In this review, recent progress on the design, fabrication, and performance of 3D heteroatom-doped nanocarbon catalysts is summarized, aiming to elucidate the effects of heteroatom doping and 3D structure on the ORR performance of nanocarbon catalysts, thus promoting the design of highly active nanocarbon-based ORR electrocatalysts. Full article