Search Results (6)

Metal foams and alloy foams are a novel class of engineering materials and have numerous applications because of their properties such as high energy absorption, light weight and high compressive strength. In the present study, the methodology adopted to develop a Ni-Cr alloy foam is discussed. Polyurethane (PU) foam of 40PPI (parts per inch) pore density was used as the precursor and coating techniques such as electroless nickel plating (ELN), ultrasonic-assisted electroplating of nickel (UAEPN), and pack cementation or chromizing were used to develop the Ni-Cr alloy foam. The surface morphology, strut thickness and minimum weight gain after each coating stage were evaluated. It was observed from the results that the adopted coating techniques did not damage the original ligament cross-section of the PU precursor. The minimum weight gain and the coating thickness after the UAEPN process were observed to be 42 g and 40–60 μm, respectively. The properties such as porosity percentage, permeability and compressive strength were evaluated. Finally, the pressure drop through the developed foam was estimated and verified to determine whether the developed foam can be used for filtering applications. Full article

A finite element model is developed to assess the effects of the TiSiCN thin film coating of the piston ring on the structural strength of the piston subsystem. The complex, cyclically variable forces are considered in load and boundary conditions. The model included combustion dynamics, contact kinetics, piston subsystem primary and secondary motions, and lubricated contact conditions to evaluate the applied forces. A comparative analysis is performed for coated and uncoated cases. Four different crown geometries are tried for selecting the best case of crown design for coated piston subsystem components. The analysis predicts better strength in coated cases compared to uncoated ones. The type-A crown design develops less stress, while the compression ring suffers the most due to elastic deformation and is more prone to fatigue failure. Full article

The machined surface integrity in the turning of hardened steels is adversely influenced by heat generation and friction which requires pacification of the temperature by the effective cooling-lubrication approach and cutting tool performance. The present research analyzes the surface integrity of hardened AISI 4140 steel during turning with recently developed scalable pulsed power plasma SPPP-AlTiSiN coated carbide tool under nanofluid-assisted minimum quantity lubrication (MQL). Zinc oxide nanoparticles and environmentally friendly radiator coolant are mixed to prepare the nano cutting fluid. This analysis addresses the various aspects of surface integrity concerning surface morphology, machined surface hardness, residual stress and white layer development, and machined surface finish under varying cutting parameters (depth of cut, speed, feed, nose radius). Response surface methodology (RSM) is suggested to predict and to optimize the surface roughness in hard turning. Thereafter, the predictive modelling and optimization results are implemented for economic analysis. According to the findings of the experiments, with a contribution of 58.18%, the feed rate possesses a high impact on the surface finish, followed by the nose radius (12.32%) and speed (0.85%). Consequently, the machined surface quality improved with the increase of the nose radius because of the minimum tool wear and due to the increase of the effective length of the cutting edge. At optimum cutting conditions, the tool life of SPPP-AlTiSiN coated carbide insert is noted as 46 minutes under nanofluid-MQL and consequently, it estimated the overall machining cost per component as Rs.23.12 in Indian currency. Full article

The machinability of materials is highly affected by their hardness, and it affects power consumption, cutting tool life as well as surface quality while machining the component. This work deals with machining of annealed AISI 4340 alloy steel using a coated carbide tool under a dry environment. The microhardness of annealed and non-annealed workpieces was compared and a significant reduction was found in the microhardness of annealed samples. Microstructure examination of the annealed sample revealed the formation of coarse pearlite which indicated a reduction of hardness and improved ductility. A commercially CVD multilayer (TiN/TiCN/Al₂O₃/ZrCN) coated cemented carbide cutting tool was employed for turning quenched and tempered structural AISI 4340 alloy steel by varying machining speed, rate of feed, and depth of cut to evaluate the surface quality, machining forces, flank wear, and chip morphology. According to the findings of experiments, the feed rate possesses a high impact on surface finish, followed by cutting speed. The prominent shape of the serrated saw tooth chip was noticed at a higher cutting speed. Machined surface finish and cutting forces during turning is a function of the wear profile of the coated carbide insert. This study proves that annealing is a low-cost and economical process to enhance the machinability of alloy steel. Full article

The machining of nickel-based super alloys is challenging, owing to the generation of high cutting temperatures, as well as difficulty in maintaining dimensional accuracy and minimizing surface roughness, which compels the use of cutting fluids for reducing these issues due to efficient cooling/lubrication strategies. The present work investigates the comparative performance of four cooling/lubrication techniques: dry cutting, wet, minimum quantity lubricant (MQL) and compressed-air modes in turning Nitronic 60 steel using a new-generation SiAlON ceramic inserts. Several machinability parameters were analyzed for performance evaluation. For this purpose, 16 cycles of turning trials were performed based on Taguchi’s L₁₆ orthogonal array experimental design by varying cutting conditions and lubrication modes. MQL exhibits beneficial effects as compared to the other lubrication conditions concerning low cutting force, improved surface finish, decreased cutting temperature, longer tool life, and lower white layer thickness on machined surface. Burr formation on the saw-tooth chip surface, as well as friction, greatly influenced the tool flank wear due to improper cooling and poor lubrication approach in dry, wet, and compressed-air-cooled machining environments in comparison to MQL-machining. From an economical perspective, the tool life in MQL machining improved by 11%, 72%, and 138% in the comparison with flooded, compressed-air, and dry conditions, respectively. The results of the study demonstrate that using the MQL system can help with heat extraction capability, and provide some promising outcomes. Full article

Sustainable manufacturing has received great attention in the last few decades for obtaining high quality products with minimal costs and minimal negative impacts on environment. Sustainable machining is one of the main sustainable manufacturing branches, which is concerned with improving environmental conditions, reducing power consumption, and minimizing machining costs. In the current study, the performance of three sustainable machining techniques, namely dry, compressed air cooling, and minimum quantity lubrication, is compared with conventional flood machining during the turning of austenitic stainless steel (Nitronic 60). This alloy is widely used in aerospace engine components, medical applications, gas power industries, and nuclear power systems due to its superior mechanical and thermal properties. Machining was performed using SiAlON ceramic tool with four different cutting speeds, feeds and a constant depth of cut. Consequently, various chip characteristics such as chip morphology, chip thickness, saw tooth distance and chip segmentation frequency were analyzed with both optical and scanning electron microscopes. Performance assessment was performed under the investigated cutting conditions. Our results show that the tool life under MQL machining are 138%, 72%, and 11% greater than dry, compressed air, and flooded conditions, respectively. The use of SiAlON ceramic tool results is more economically viable under the MQL environment as the overall machining cost per component is lower ($0.27) as compared to dry ($0.36), compressed air ($0.31), and flooded ($0.29) machining conditions. The minimum quantity lubrication technique outperformed the other investigated techniques in terms of eco-friendly aspects, economic feasibility, and technical viability to improve sustainability. Full article