Macromol, Volume 1, Issue 3 (September 2021) – 4 articles

Acylhydrazone-based fluorescent conjugated microporous polymers (CMPs) with inter-and intra-hydrogen bonding-controlled emissive properties were prepared. The synthesized CMPs (BH-CMP and ABH-CMP) were characterized by Fourier-transform infrared spectroscopy, X-ray diffraction, solid-state ¹³C cross polarization/magic angle spinning nuclear magnetic resonance spectroscopy, and photoluminescence spectroscopy. Interestingly, BH-CMP exhibited emission enhancement via adsorption of water molecules, whereas the emission of ABH-CMP, which possesses free amine groups, decreased upon the addition of water molecules. The differences in the emission trends of BH-CMP and ABH-CMP in the presence of water molecules originate from the formation of different hydrogen-bonding networks in each CMP. The acylhydrazone-based CMPs were applied to the detection of nitroaromatic compounds. As a result, ABH-CMP in DMF exhibited high selectivity for 1,3,5-trinitrotoluene (TNT) over other nitroaromatic compounds nitrobenzene, 1-chloro-4-nitrobenzene, 2,3-dichloronitrobenzene, and 2,4-dinitrotoluene. Full article

During the past two decades, immobilization of titanium dioxide (TiO₂), a well-known photocatalyst, on several polymeric substrates has extensively gained ground since it limits the need of post-treatment separation stages. Taking into account the numerous substrates tested for supporting TiO₂ photocatalysts, the use of biodegradable polymer seems a hopeful option owing to its considerable merits, including the flexible nature, low price, chemical inertness, mechanical stability and wide feasibility. The present review places its emphasis on recently published research articles (2011–2021) and exhibits the most innovative studies facilitating the eco-friendly biodegradable polymers to fabricate polymer-based photocatalysts, while the preparation details, photocatalytic performance and reuse of the TiO₂/polymer photocatalysts is also debated. The biodegradable polymers examined herein comprise of chitosan (CS), cellulose, alginate, starch, poly(lactid acid) (PLA), polycaprolactone (PCL) and poly(lactide-co-glycolide) (PLGA), while an emphasis on the synthetical pathway (dip-coating, electrospinning, etc.) of the photocatalysts is provided. Full article

The current study is focused on the development of highly stable drug nanocarriers by encapsulating losartan potassium (LSR) into an amphiphilic biocompatible poly(2-methyl-2-oxazoline)-grad-poly(2-phenyl-2-oxazoline) (PMeOxz₇₂-grad-PPhOxz₂₈) gradient copolymer (GC). Based on dynamic light scattering (DLS), the PMeOxz₇₂-grad-PPhOxz₂₈ (where the subscripts denote %wt composition of the components) GC formed micelles and aggregates of 13 nm and 96 nm in aqueous milieu. The presence of hydrophobic LSR molecules altered the structural characteristics of the GC, modulating the organization of the polymeric components and revealing the formation of hyper micellar nanostructures in addition to micelles. The 2D-NOESY experiments evidenced intermolecular interactions between the phenyl ring of LSR with the phenyl group of PPhOxz and eminent correlations between the butyl chain of LSR with the phenyl group of PPhOxz and methylene group of PMeOxz, respectively. Additionally, NMR studies as a function of temperature demonstrated that the presence of hydrophilic PMeOxz segments in the gradient core of PMeOxz₇₂-grad-PPhOxz₂₈ nanoassemblies induced an increased fluidity of the core matrix, especially upon heating, thus causing water penetration, resulting in increased proton mobility. Lastly, the ultrasound release profile of LSR signified that a great amount of the encapsulated LSR is tightly bound to the PMeOxz₇₂-grad-PPhOxz₂₈ nanoassemblies. Full article