Fabrication of Fe-Al Intermetallic Foams via Organic Compounds Assisted Sintering
Abstract
:1. Introduction
2. Results and Discussion
Content of chemical compound (CM and PA) used in experiment (wt%) | Porosity (%) | |
---|---|---|
Cholesteryl myristate (CM) | Palmitic acid (PA) | |
0 | 36.2 ± 0.7 | |
0.5 | 43.1 ± 1.0 | 46.6 ± 2.9 |
1 | 41.1 ± 0.4 | 44.2 ± 5.3 |
2 | 41.7 ± 5.3 | 45.0 ± 0.8 |
3 | 47.2 ± 1.0 | 47.4 ± 3.9 |
Chemical compound | P < 0.05 |
---|---|
Concentration of PA | + |
Concentration of CM | + |
Factor | P < 0.05 | Interaction | P < 0.05 |
---|---|---|---|
Concentration of the chemical compound | + | Concentration-type | − |
Type of the chemical compound | − |
3. Experimental Section
4. Conclusions
Acknowledgements
Author Contributions
Conflicts of Interest
References
- Murakami, T.; Akagi, T.; Kasai, E. Development of porous iron based material by slag foaming and its reduction. Proc. Mater. Sci. 2014, 4, 27–32. [Google Scholar] [CrossRef]
- Yang, C.C.; Nakae, H. Foaming characteristics control during production of aluminum alloy foam. J. Alloys Comp. 2000, 313, 188–191. [Google Scholar] [CrossRef]
- Mori, K.; Nishikawa, H. Cold repeated forming of compact for aluminium foam. J. Mater. Process. Technol. 2010, 210, 1580–1586. [Google Scholar] [CrossRef]
- Karczewski, K.; Jóźwiak, S.; Bojar, Z. Mechanisms of strength properties anomaly of Fe-Al sinters by compression tests at elevated temperature. Arch. Metall. Mater. 2007, 52, 361–366. [Google Scholar]
- Łyszkowski, R.; Bystrzycki, J. Influence of temperature and strain rate on the microstructure and flow stress of iron aluminides. Arch. Metall. Mater. 2007, 52, 347–350. [Google Scholar]
- Łyszkowski, R.; Bystrzycki, J. Hot deformation and processing maps of a Fe-Al intermetallic alloy. Mater. Charact. 2014, 96, 196–205. [Google Scholar] [CrossRef]
- Gao, H.; He, Y.; Zou, J.; Xu, N.; Liu, C.T. Tortuosity factor for porous FeAl intermetallics fabricated by reactive synthesis. Trans. Nonferrous Met. Soc. China 2012, 22, 2179–2183. [Google Scholar]
- Gao, H.; He, Y.; She, P.; Zou, J.; Xu, N.; Jiang, Y.; Huang, B.; Liu, C.T. Porous FeAl intermetallics fabricated by elemental powder reactive synthesis. Intermetallics 2009, 17, 1041–1046. [Google Scholar] [CrossRef]
- Siemiaszko, D.; Jóźwiak, S.; Czarnecki, M.; Bojar, Z. Influence of temperature during pressure-assisted induction sintering (PAIS) on structure and properties of the Fe40Al intermetallic phase. Intermetallics 2013, 41, 16–21. [Google Scholar] [CrossRef]
- Durejko, T.; Zietala, M.; Polkowski, W.; Czujko, T.; et al. Thin wall tubes with Fe3Al/SS316L graded structure obtained by using laser engineered net shaping technology. Mater. Design 2014, 63, 766–774. [Google Scholar] [CrossRef]
- Durejko, T.; Lipinski, S.; Bojar, Z.; Bystrzycki, J. Processing and characterization of graded metal/intermetallic materials: The example of Fe/FeAl intermetallics. Mater. Des. 2011, 32, 2827–2834. [Google Scholar] [CrossRef]
- Rolink, G.; Vogt, S.; Sencekova, L.; Weisheit, A.; Poprawe, R.; Palm, M. Laser metal deposition and selective laser melting of Fe-28 at% Al. J. Mater. Res. 2014, 29, 2036–2043. [Google Scholar] [CrossRef]
- Podrez-Radziszewska, M.; Jóźwik, P. Influence of heat treatment on resistance to electrochemical corrosion of the strain-hardened strips made of the Ni3Al phase based alloys. Arch. Civil Mech. Eng. 2011, 11, 1011–1021. [Google Scholar] [CrossRef]
- Gedevanishvili, S.; Deevi, S.C. Processing of iron aluminides by pressureless sintering through Fe + Al elemental route. Mater. Sci. Eng. 2002, 163–176. [Google Scholar] [CrossRef]
- Karczewski, K.; Jóźwiak, S.; Chojnacki, M.; Bojar, Z. The influence of different additives on the kinetics of Self-propagating High-temperature Synthesis during the sintering process of Fe and Al elemental powders. Intermetallics 2010, 18, 1401–1404. [Google Scholar] [CrossRef]
- Chojnacki, M.; Jóźwiak, S.; Karczewski, K.; Bojar, Z. Modification of Fe and Al elemental powders’ sintering with addition of magnesium and magnesium hydride. Intermetallics 2011, 19, 1555–1562. [Google Scholar] [CrossRef]
- Zhang, L.P.; Zhao, Y.Y. Fabrication of high melting-point porous metals by lost carbonate sintering process via decomposition route. Proc. Inst. Mech. Eng. Part B J. Eng. Manuf. 2008, 222, 267–271. [Google Scholar] [CrossRef]
- Paswan, D.; Mistry, D.; Sahoo, K.L.; Srivastava, V.C. Development of iron-based closed-cell foams by powder forging and rolling. J. Mater. Eng. Perform. 2013, 22, 2201–2209. [Google Scholar]
- Diologent, F.; Goodall, R.; Mortensen, A. Creep of aluminium–magnesium open cell foam. Acta Mater. 2009, 57, 830–837. [Google Scholar] [CrossRef]
- Osorio-Hernández, J.O.; Suarez, M.A.; Goodall, R.; Lara-Rodriguez, G.A.; Alfonso, I.; Figueroa, I.A. Manufacturing of open-cell Mg foams by replication process and mechanical properties. Mater. Design 2014, 64, 136–141. [Google Scholar] [CrossRef]
- Łazińska, M.; Durejko, T.; Lipiński, S.; Polkowski, W.; Czujko, T.; Varin, R.A. Porous graded FeAl intermetallic foams fabricated by sintering process using NaCl space holders. Mater. Sci. Eng. A 2015. [Google Scholar] [CrossRef]
- Jarvis, T.; Voice, W.; Goodall, R. The bonding of nickel foam to Ti-6Al-4V using Ti-Cu-Ni braze alloy. Mater. Sci. Eng. A 2011, 528, 2592–2601. [Google Scholar] [CrossRef]
- Ismail, M.H.; Goodall, R.; Davies, H.A.; Todd, I. Formation of microporous NiTi by transient liquid phase sintering of elemental powders. Mater. Sci. Eng. C 2012, 32, 1480–1485. [Google Scholar] [CrossRef]
- Ismail, M.H.; Goodall, R.; Davies, H.A.; Todd, I. Porous NiTi alloy by metal injection moulding/sintering of elemental powders: Effect of sintering temperature. Mater. Lett. 2012, 70, 142–145. [Google Scholar] [CrossRef]
- Nowak-Stępniowska, A.; Małecki, M.; Wiktorska, K.; Romiszewska, A.; Padzik-Graczyka, A. Inhibition of cell growth induced by photosensitizer PP(Arg)2-mediated photodynamic therapy in human breast and prostate cell lines. Part I. Photodiagn. Photodyn. Ther. 2011, 8, 39–48. [Google Scholar] [CrossRef]
© 2015 by the authors; licensee MDPI, Basel, Switzerland. This article is an open access article distributed under the terms and conditions of the Creative Commons Attribution license (http://creativecommons.org/licenses/by/4.0/).
Share and Cite
Karczewski, K.; Stępniowski, W.J.; Kaczor, P.; Jóźwiak, S. Fabrication of Fe-Al Intermetallic Foams via Organic Compounds Assisted Sintering. Materials 2015, 8, 2217-2226. https://doi.org/10.3390/ma8052217
Karczewski K, Stępniowski WJ, Kaczor P, Jóźwiak S. Fabrication of Fe-Al Intermetallic Foams via Organic Compounds Assisted Sintering. Materials. 2015; 8(5):2217-2226. https://doi.org/10.3390/ma8052217
Chicago/Turabian StyleKarczewski, Krzysztof, Wojciech Jerzy Stępniowski, Piotr Kaczor, and Stanisław Jóźwiak. 2015. "Fabrication of Fe-Al Intermetallic Foams via Organic Compounds Assisted Sintering" Materials 8, no. 5: 2217-2226. https://doi.org/10.3390/ma8052217