Global energy markets are rapidly changing. Renewable energy technologies now constitute more than half of the new power plants built worldwide each year [
1]. Unlike hydro and geothermal renewable energy sources which show readily stable forms of energy over time, other renewable energy sources cannot be stockpiled and must be used when available or be regarded as lost energy potentials. The major restraint for increasing the share of renewable energy sources is their intermittency, which can be addressed through energy storage when available and energy use when needed. Therefore, to bring renewable energy sources (e.g., solar and wind) to independence and reliability, adequate energy storage technologies (ESTs) must be deployed. The role of energy storage systems in integration with renewable energy sources is more evident in the remote and stranded regions where connecting to the nationwide electricity grid is cost prohibitive. Although the energy is mostly required in the form of electricity, for economic reasons it is possible to convert the electricity and store it in another form of energy which can then be converted back to electricity when needed [
2]. There are a number of well-established and enormous developing technologies offering significant potentials to enable energy storage in integration with various renewable sources (
Figure 1). Present ESTs can be loosely categorized as either mechanical, electrical, thermal, and chemical systems [
3]. Each category contains several technologies for consideration as outlined in
Figure 1. Up to the beginning of 21st century, the only viable energy storage option was in the form of pumped hydro storage that is only practicable at certain topographic conditions. Today, around 1600 energy storage projects at different scales with a total capacity of approximately 193 MW are constructed worldwide (
Figure 2) [
4]. The feasibility of each energy storage application would highly depend on several factors including: the efficiency, energy capacity, energy density, run time, capital investment costs, response time, lifetime in years and cycles, self-discharge, and maturity of the technology. Flywheels, supercapacitors, and superconducting magnetics show the highest maximum efficiency, and fastest response times, however they have among the highest capital costs [
3]. Pumped hydro storage systems have the highest capacity by a large margin, but are also among the least energy dense storage options. The storage technologies capable of providing continuous electricity supply for 24 h or more are underground compressed air energy storage, pumped hydro, fuel cells and high temperature thermal energy storage systems, However, they are expensive to place and build, with long construction time, and only suitable for large scale projects [
5]. Batteries, overall, are widely used EST because they are clean, efficient, scalable, and can provide the stored energy instantaneously. However, they are relatively hindered by high costs, high rate of self-discharge, short lifecycle, and the presence of hazardous/toxic components in their assembly [
5]. A life cycle assessment of batteries compatible with PV systems indicates that batteries are the most responsible for the environmental impacts, due to their relatively short lifespan and heavy metal content [
6].
The choice for the right EST(s) for a particular location would highly depend on many geographical, economic, social, and political factors as the applications of the available technologies involve significant investments and funding which often requires adequate regulatory support [
7]. In this paper, we have highlighted the renewable energy and EST arrangements that are currently in place for the electric power supply in King Island (in Tasman Sea, Southeast Australia) and studied a similar energy portfolio for a reliable water supply to the residents of the island via a hypothetical desalination plant. We have argued that EST option is mainly relevant to the energy usage application, whereas for desalination purposes, this option is techno-economically unfeasible compared to “water storage options”.
1.1. King Island Case Study
King Island (Latitude 39.9 S, Longitude 144 E) is located at Tasmania’s northwest, between Victoria and Tasmania (
Figure 3A). The population of King Island is 1600 residents as in year 2014 [
8], the majority are living in Currie. It is common for off-grid and remote communities like King Island to obtain electricity via conventional diesel generators. However in King Island, an innovative power system was developed to supply over 65% of King Island’s energy needs using renewable energy, thereby reducing carbon dioxide emissions by more than 95% [
9]. This power system consists of a hybrid of solar, wind, and diesel/biodiesel power generators and a battery, fly wheel, and a resistor for energy storage. These power options are connected via a smart grid technology that helps match the island’s energy needs with the available energy supply sources. The aim of this project is to allow the power system to rely less on diesel generation and provide a reliable and stable electricity supply while reducing carbon dioxide emissions. To increase community awareness/participation in the power generation/management portfolio of the island, a live data display is demonstrated online representing the proportion of power generation/storage/usage at every time step (
Figure 3B).
King Island has a total area of 1098 km
2, where 178 m
2 of land is covered by water, mostly brackish. The groundwater quality is also poor due to extensive agricultural activities, poor vegetation management, and geographic reasons such as landform and climate patterns [
10]. All of the above have led to elevated salt levels in water streams and comparatively reveal high nutrient levels than other rivers in Tasmania [
10]. Importantly, the quantity and quality of freshwater have directly impacted the development and population growth on the island. Besides, King Island has a 145 km coastline and therefore easy access to seawater, solar, and wind resources. For example, westerly winds can reach over 100 km/h [
11]. Therefore, the potential of desalination can be realized in a sustainable concept of employing renewable technologies and eliminating excessive GHG emissions, which is a very important strategy for the future of this island.
In this paper, we have proposed an off-grid desalination plant that generates adequate freshwater for the residents of King Island by forecasting the daily water demand for the next 25 years. We have developed a techno-economic model for three primary and two hybrid desalination technologies. The most economical model is integrated with renewable energy sources as a mean of power production. In this hybridization and under transient conditions, the annual performance of four proposed scenarios is analyzed. In the first scenario, a solar PV field is sized and optimized with a battery-set for energy storage, whereas in the other three scenarios the battery-set is eliminated. In the second scenario the desalination plant and solar PV field are oversized to generate instant and sufficient freshwater during the day and store access water in storage tanks for night usage. In the third and fourth scenarios, wind turbines are integrated in the energy portfolio for appropriate energy production in solar deficit times. We have proved that in integrating renewable energy with desalination process, energy storage is not a viable option and we have developed a scalable economic water storage option that is able to meet freshwater demand for the residents of King Island or similar case-studies.
1.2. Process Description and Modelling
This study utilizes two software programs, Desalination Economic Evaluation Program (DEEP) [
12] and System Advisory Model (SAM) [
13]. DEEP, developed by the International Atomic Energy Agency (IAEA), is an effective modelling instrument to evaluate various power and desalination cogeneration configurations and is suitable for comparison analysis among different desalination technologies. SAM, developed by the National Renewable Energy Laboratory (NREL), is a performance and finance modelling tool vigorous in providing the cost of energy estimates for grid-connected power projects based on installation and operating costs inputs and system design parameters.
The freshwater demand for the residents of King Island varies on a daily and seasonal basis while the population is increasing. We projected the total water demand and sized the desalination plant accordingly, while the energy input either from the solar field, wind turbines, or power storage has to satisfactorily meet the immediate load at all times. In DEEP, we developed three primary desalination models using well-established desalination technologies namely; multi-stage flash (MSF), multiple effect distillation (MED), and reverse osmosis (RO) [
14,
15,
16,
17]. In addition, we developed two desalination hybrid models; MSF + RO and MED + RO. In these five models, we assumed the electric power comes from the grid to eliminate the attached power plant and only counted for the capital cost (CAPEX) of the desalination plant. By selecting the most cost-effective desalination option, we entered the financial data for selected desalination plant as a single entity into SAM model. In SAM, we proposed four scenarios for energy production and storage:
Scenario 1: The solar field is sized to provide instant power for desalination and also excess power is stored in designated batteries to meet the load in solar insufficient times.
Scenario 2: The solar field and desalination plant are sized to meet instant water demand and also produce excess water storable in designated water tanks to meet the load when the solar field is inactive.
Scenario 3: Cogenerated power from the solar field and a wind farm (two wind turbines) is optimized to meet the immediate load and store excess water in designated storage tanks for later use.
Scenario 4: Similar to Scenario 3, but optimized for larger wind farm (four wind turbines) and smaller size for solar field.
The cost components of the land value, desalination plants, solar PV field, wind turbines, batteries, water storage systems, including tax rates, incentives, debt terms and all financial parameters—are checked and updated accordingly.
1.3. Desalination Options
As of June 2015, there were 18,426 desalination plants established in 150 countries, producing more than 86.8 million cubic meters of pure water per day [
18]. Traditional seawater desalination is climate independent and only limited by investment bounds and energy accessibilities. Desalination plants enjoy economies of scale in treatment facility construction. Large desalination plants built between 2000 and 2005 were typically designed to supply 5%–10% of the drinking water of coastal cities. More recently, regional or national seawater desalination projects in countries such as Spain, Australia, Algeria, and Singapore have been planned to supply 20%–50% of a city’s long-term freshwater demand [
19]. Other large cities in Gulf Corporation Countries (GCC) and the Middle East and North Africa (MENA) region are 100% dependent on desalinated water [
20]. Potential sites for large desalination plants need to meet specified criteria such as proximity to the ocean, access to a power source, and also minimal environmental impact [
21]. There are three different key principles governing the desalination process briefly outlined below [
22]:
- (1)
Phase Change Method: This process involves heating the feedwater to a certain point to generate steam, which passes through a condenser, thereby producing liquid water in the output. Since there is a phase change directly related to the heat input, this technology is more compatible with waste/low-grade heat, including solar thermal technologies. Mechanical vapor compression (MVC), thermal vapor compression (TVC), multi-effect distillation (MED), and multi-stage flash distillation (MSF) are partially/totally abided by this principle and highly compatible with solar thermal applications [
14].
- (2)
Non-Phase Change Method: In this method, the feedwater remains in liquid phase and does not evaporate. The feedwater is pressurized on a selective barrier (membrane) to prevent the penetration of dissolved solids and impurities with the pure water. The required pressure is maintained by powerful pumps, often using electricity as a source of power. The main applications of this principle are Electro-dialysis (ED) and Reverse Osmosis (RO). Reverse Osmosis are modular and scalable units relatively efficient, less-expensive, and easy to replace [
23]. The current worldwide market share is almost 33% for phase-change methods compared to 67% for non-phase change methods [
24].
- (3)
Hybridization method: This refers to types of hybrid processes which combine two processes used for the desalination processes (e.g., RO + MED). In this way, the water quality can be improved in a substantial way by reducing the amount of the total dissolved salts present in the feed water. It is a thermo-membral process that is hybridizing both thermal and membrane distillation technologies to accurately blend and produce high quality water. This option is more viable in conjunction with the nearby power plant. In this method, the waste heat from the power plant can be utilized for the first water production method, while the generated electricity is utilized for the second. The key characteristics of these methods as reported by the world health organization (WHO), 2007 [
22] and are summarized in
Table 1.
Due to the remote and isolated nature of King Island encircled by the ocean, a desalination plant would be an appropriate solution to secure freshwater demand for the residents of the island. The capacity of the proposed desalination plant should sufficiently meet all domestic/nondomestic freshwater for the population of the island presently and in the next 25-year lifespan of the project. Based on Australia’s population growth rate (0.3% per annum) [
8], we estimated the population of the island in 25 years would approximately be 1740 persons. The calculated water demand for this population based on the Tasmanian average daily water usage is equal to 4 ML per day [
25]. All financial parameters, interest rates, council fees, and tax rates are extracted from credible technical and government reports [
12,
26,
27] and applied accordingly. These inputs are used in DEEP to model the financial logistics for different desalination technologies.
Table 2 shows the main variables used in DEEP models.
Figure 4 illustrates the cost components and the overall cost for the three primary and two hybrid desalination technologies developed to produce 4 ML/day freshwater for the residents of King Island. This cost estimate is based on typical grid-connected desalination and before any integration with renewable sources. The desalination plant site is carefully chosen to reduce trenching, piping, and water transport costs. This site is the nearest to the main population city (Currie) and also to the sea-shore for effective feedwater delivery and also for brine discharge. It is well-established that SMF and MED would be economic candidates for very large-scale desalination process, but for small-scale desalination (i.e., 4 ML/day), the RO would prevail.
Figure 4 clearly demonstrates that the RO plant shows the lowest cost of water production compared to other options. This technology is the most cost-effective due to its low energy consumption and quick response at start-up and shutdown compared to thermal processes. It is noteworthy that an RO desalination plant can easily be operated by electric energy and, therefore, solar PV would be ideal candidate for electric power production. Both solar PV and RO units are modular and scalable to accurately meet the energy and water demand, respectively. Hybrid options can be derived based on the combination ratio between RO and thermal processes. Larger portions for thermal technologies would increase the heat portion and subsequently drive the overall cost higher. We built the hybrid models based on 50% contribution from each technology as presented in
Figure 4.
1.4. Renewable Energy Options
In King Island, because of a low population density and poor infrastructure for freshwater and electricity transmission/distribution, renewable energy for desalination is a favourable option in both the short-term and long-term. Enormous research for integrating renewable power sources with various desalination technologies has been conducted [
28,
29] It is well-established that solar energy is the most promising application with a significant contribution for sustainability [
30]. Similarly, wind turbines are another sustainable approach for energy production. The transient nature of wind kinetics is different to that of solar energy. Wind turbines, if well-designed, may provide adequate energy in night times and in winter when solar energy is insufficient. A good combination of these two energy sources may better match the dynamic energy demand of RO desalination plant that is mainly governed by freshwater withdrawal and consumers’ lifestyle. Freshwater demand not only fluctuates on an hourly basis, but also responds to climate variation and seasonal deviation. Dry and wet seasons also impact the freshwater withdrawal rates. In this study, we have incorporated two representative profiles that reflect on the hourly and seasonal load variation factors. These hourly and monthly water consumption profiles are based on credible water consumption forecasting studies [
31,
32]. As shown in
Figure 5A for average daily profile, freshwater consumption is minimum during early hours of the day, peaking at morning times due to morning showers, toilets, breakfast, etc. Then water consumption rates decrease in midday limited to typical household duties (e.g., cooking, cloth washing, etc.), and then rise in the evening because of night showers before being declined to their lowest after midnight.
Figure 5B shows water consumption profile reflecting monthly variation. Notably, water consumption drops during winter times because of less demand for gardening and irrigation and also reflecting moderate climate and cold ambient temperatures. The desalination plant must be equipped to meet water demand at all times, particularly in those peak hours and throughout the year. The solar field, wind farm, desalination capacity, standby units, pumps, and energy/water storage must be well-scaled to sufficiently meet freshwater demand at all times.
To compare energy and water storage compatible with different renewable energy sources, four potential scenarios are considered. The objective of this comparison is to determine the most feasible option that can sufficiently meet the variable load at all times and at the lowest cost. These four scenarios are described above and depicted in
Figure 6. Each of the symbols used for solar PV field, wind turbine, batteries, inverters, RO units, and water storage tanks are scaled to a particular capacity as outlined in the legend. The energy, freshwater, feed/brine water, and inactive streams also clarify the operation schemes in day and night modes. In Scenario 1, the solar PV field is sized to meet instant water load in day times and store excess electricity in a supplementary battery set. The inverters are also sized to convert the DC current at the PV outlet to AC current, usable by the pumps to bring the feed water pressure to the design point. As the desalination plant is always available to work on-demand, the design capacity should be able to meet the highest demand (worst case), although most of the times, it only needs to operate on partial load. This arrangement over-sizes the solar PV field, invertors, and battery storage capacity accordingly, but comparatively lowers the size of RO desalination plant. In Scenario 2, the batteries are eliminated but the desalination plant capacity is increased to produce more water during the day and shutdown at night times. The adequate sizing of water storage tanks, that store excess water, is able to control demand; extra water produced in the summer season helps in responding to demand in the winter without the need for oversizing solar PV field to respond to winter energy deficits. In Scenario 3, this concept is further elaborated by reducing solar PV field and introducing 2 × 2.5 MW wind turbines. The benefit of wind turbines is in providing energy, although intermittent, when most needed (most valued in night times and winter season). This combination is expected to decrease solar PV field size and water storage capacity as of Scenario 2. In Scenario 4, the role of wind contribution is doubled by employing 4 × 2.5 MW wind turbines. Although this scenario will increase the cost of wind farm, but it will also significantly reduce the solar PV field and water storage capacity. The main economic assumptions adopted for these four scenarios are presented in
Table 3.