Search Results (5)

The growing demand for ultra-low sulfur fuels has intensified interest in recovering strategic metals from the large volumes of hazardous hydrodesulfurization catalysts that are discarded yearly. This work evaluates a task-specific ionic liquid, tri-n-octylammonium bis(2-,4-,4-trimethylpentyl)-phosphinate [TOA][Cy272], synthesized by the acid–base neutralization of tri-n-octylamine and Cyanex 272. FT-IR spectroscopy confirmed complete proton transfer and the formation of a stable ion pair. Liquid–liquid extraction tests were conducted with synthetic Co–Ni–Mo solutions (0.1–2.5 g/L each), a varying ionic liquid concentration (10–50 vol%), pH (1.5–12.5), and organic/aqueous ratio (1:1). At 35 vol% of ionic liquid and pH 2, the extraction efficiency for Mo reached 94%, with separation factors βMo/Ni = 12 and βMo/Co = 7.5; Co and Ni uptake remained ≤15%. Selectivity decreased at higher metal loadings because of ionic liquid saturation, and an excessive ionic liquid amount (>35%) offered no benefit, owing to viscosity-limited mass transfer. Stripping studies showed that 1 M NH₄OH stripped about 95% Mo, while leaving Co and Ni in the organic phase; conversely, 2 M HCl removed 92–98% of Co and Ni, but <5% Mo. Overall Mo recovery of about 95% was obtained by a two-step extraction/stripping scheme. The results demonstrate that [TOA][Cy272] combines the cation exchange capability of quaternary ammonium ILs with the strong chelating affinity of organophosphinic acids, delivering rapid, selective, and regenerable separation of Mo from mixed-metal leachates and wastewater streams. Full article

Memristors are promising candidates for next-generation non-volatile memory devices, offering low power consumption and high-speed switching capabilities. However, conventional metal oxide-based memristors are constrained by fabrication complexity and high costs, limiting their commercial viability. Organic–inorganic hybrid perovskites (OIHPs), known for their facile solution processability and unique ionic–electronic conductivity, provide an attractive alternative. This study presents a conjugated polyelectrolyte (CPE), PhNa-1T, as an interlayer for OIHP memristors to enhance the high-resistance state (HRS) performance. A post-treatment process using n-octylammonium bromide (OABr) was further applied to optimize the interlayer properties. Devices treated with PhNa-1T/OABr achieved a significantly improved ON/OFF ratio of 2150, compared to 197 for untreated devices. Systematic characterization revealed that OABr treatment improved film morphology, reduced crystallite strain, and optimized energy level alignment, thereby reinforcing the Schottky barrier and minimizing current leakage. These findings highlight the potential of tailored interlayer engineering to improve OIHP-based memristor performance, offering promising prospects for applications in non-volatile memory technologies. Full article

The influence of n-octylammonium iodide (OAI, passive layer) on the types of phases formed in a (MACl)_0.33FA_0.99MA_0.01Pb(I_0.99Br_0.01)₃ perovskite film was studied using X-ray diffraction. Using UV spectrophotometric techniques, it was determined how varied OAI additive layer ratios affected the linear and nonlinear optical characteristics of glass substrates/FTO/compact TiO₂/mesoporous TiO₂/(MACl)_0.33FA_0.99MA_0.01Pb(I_0.99Br_0.01)₃ films. All films’ direct optical bandgap energies were determined to be 1.54 eV. The effects of OAI addition on the films’ photoluminescence intensity and emitted colors were also investigated. For the fabricated perovskite solar cells (PSCs) without an OAI passivation layer, the corresponding power conversion efficiency (PCE), open-circuit voltage (V_OC), short-circuit current density (J_SC), and fill factor (FF) values were 18.8%, 1.02 V, 24.6 mAcm⁻², and 75%, respectively. When the concentration of OAI reached 2 mg, the maximum obtained values of PCE, V_OC, J_SC, and FF were 20.2%, 1.06 V, 24.2 mAcm⁻², and 79%, respectively. The decreased trap density and increased recombination resistance were responsible for the improvement in solar cell performance. Full article

The article presents data on the solvent extraction separation of rare-earth elements (REEs), such as La(III), Ce(III), Pr(III), and Nd(III), using synergic mixtures of methyltrioctylammonium nitrate (TOMANO₃) with tri-n-butyl phosphate (TBP) from weakly acidic nitrate solutions. Specifically, experimental results on separation of REEs, for the pair Ce(III)/Pr(III) for quaternary mixtures of REEs (La(III), Ce(III), Pr(III), Nd(III)) and for the pair La(III)/Pr(III) for solutions containing La(III), Pr(III), and Nd(III), are presented. It was shown that effective separation for the pair Ce(III)/Pr(III) from a solution containing 219 g Ce(III)/L, 106 g La(III)/L, 20 g Pr(III)/L, 55 g Nd(III)/L, and 0.1 mol/L HNO₃, was achieved using 56 steps of a multistage, counter-current solvent extraction cascade with scrubbing, at an organic-to-aqueous phase volume ratio (O/A) equal to 2/1 on the extraction section and O/A equal to 4/1 on the scrubbing section, using 3.3 mol/L solutions of the mixture TOMANO₃-TBP with molar ratio 0.15:0.85 in dodecane. Separation for the pair La(III)/Pr(III) could be achieved using a solvent extraction cascade with scrubbing in 32 steps at O/A equal to 2/1 on the extraction section and O/A equal to 2.8/1 on the scrubbing section of the solvent extraction cascade from a solution containing 258 g La(III)/L, 58 g Pr(III)/L, 141 g Nd(III)/L, and 0.1 mol/L HNO₃ with 3.0 mol/L solution of the mixture TOMANO₃-TBP with molar ratio 0.2:0.8 in dodecane. Full article

All-inorganic perovskites consisting of only inorganic elements have been recently considered as highly stable semiconductors for photoactive layer of optoelectronics applications. However, the formation of high-quality thin film and trap-reduced interface has still remains an important task, which should be solved for improving the performances of all-inorganic perovskite-based photovoltaics. Here, we adopted facile method that could reduce charge-carrier recombination by depositing a passivation agent on the top surface of the CsPbBr₃ all-inorganic perovskite layer. We also found that the CsPbBr₃ perovskite photovoltaic prepared from surface treatment method using n-octylammonium bromide provides an improved stability in ambient environment and 1-sun illuminating condition. Therefore, the perovskite photovoltaics fabricated from our approach offered an improved power conversion efficiency of 5.44% over that of the control device without surface treatment (4.12%). Full article