Search Results (6)

A novel multiple solid waste-based cementitious material (MSWCM) was developed to immobilize municipal solid waste incineration (MSWI) fly ash. The compressive strength of MSWCM with different ratios of MSWI fly ash reached the standard requirements after curing for 28 days. X-ray powder diffraction (XRD) in combination with the Rietveld method was employed to investigate the content and phase transformation of hydration products. The main hydration products of pure MSWCM paste were C-S-H, hydroxyapatite, ettringite and C-A-S-H. With increases in curing time, the content of ettringite and C-A-S-H increased significantly. The main hydration products of MSWCM paste with MSWI fly ash were C-S-H and Friedel’s salt. The contents increased markedly with increased curing time from 21.8% to 28.0% and from 8.53% to 16.7%, respectively. Additionally, a small amount of PbHPO₄ (0.51–0.96%) and lead phosphate Pb₃(PO₄)₂ (0.14–0.51%) were detected, indicating that phosphate had an effective curing effect on lead ions. The results showed that most of the hydration reactions had started at the initial stage of curing and reacted quickly to form a large number of hydration products. The quantitative analyses of hydration products provide essential information for understanding the immobilization mechanism of MSWI fly ash in MSWCM paste. Full article

In this paper, the strength characteristics and erosion resistance of solid waste incineration (MSWI) powder were studied. Firstly, the optimum process for the preparation of regenerated powder from MSWI bottom slag by ball milling was determined as follows: rotational speed 350 r/min, time 45 min. The strength activity index of regenerated powder reached the maximum when the substitute content of powder was 30%. Secondly, the semi-erosion method was used to study the strength variation rule of mortar with different content of MSWI powder in semi-immersion of salt solution. It was found that the higher the content of MSWI powder, the greater the anti-erosion coefficient of mortar specimen. Finally, the capillary rise test, crystallization test and capillary pore water absorption test were used to study the total porosity, coarse capillary-pore porosity and fine-capillary pore porosity of concrete containing MSWI powder. The results showed that, with the increase in MSWI powder content, the above pore structure properties were improved. The results revealed the transport and crystallization process of salt solution in concrete mixed with MSWI powder and the mechanism of corrosion resistance. Full article

In this paper, the effects of dry density, w/c ratio, and municipal solid waste incineration (MSWI) powder on the multi-scale properties and internal pore structure of foamed concrete were studied by using a single-factor controlled experiment. It was found that an increase in the dry density of foamed concrete could effectively reduce the porosity, leading to the improvement of compressive strength and impermeability and to the reduction of water absorption. The compressive strength, water absorption, and impermeability were mainly affected by the porosity when the w/c ratio changed. With the increase in porosity, the water absorption rate increased, and the compressive strength and impermeability decreased. The addition of MSWI powder caused no obvious change in the overall pore size distribution of the foamed concrete, and there was no significant change in the water absorption and impermeability of the structure. However, because the hydration activity of MSWI powder was lower than that of ordinary Portland cement, the compressive strength of foamed concrete decreased with the increase in MSWI powder. Full article

In this paper, the mechanical properties of micropowder cement mortar and engineered cementitious composites (ECC), using different processing municipal solid waste incineration (MSWI) as a mineral admixture, were investigated. Through the direct ball milling method, ball milling heat treatment method, water washing ball milling method and water washing heat treatment ball milling method, the mechanical properties of MSWI bottom slag-regenerated micropowder cement mortar were tested. Compared with other groups, the flexural strength and compressive strength of the specimen prepared by the MSWI after washing and heating (750 °C, 5 h) were the highest, which reached 82.0% and 81.0% of the reference group, respectively. Based on this treatment, a uniaxial tensile test, three-point bending test and single fiber pull-out test were then carried out to explore the relevant ECC properties containing MSWI. The strain-hardening index PSH of ECC was determined by analyzing the fracture toughness and elastic modulus, fiber/matrix interface chemical bond and friction bond strength of ECC containing MSWI. The results showed that the PSH index of ECC was higher when the treated powder content was 2.2, the w/c ratio was 0.25 and the fiber volume content was 2.0%. This led to higher tensile ductility, which made it easier to achieve stable multi-slit cracking and strain-hardening behavior. Full article

Material from the electric arc furnace smelting of municipal solid waste incineration (MSWI) bottom ash was easily converted into highly porous glass-ceramics by a combination of inorganic gel casting and sinter-crystallization at 1000 °C. In particular, the gelation of aqueous suspensions of fine glass powders, transformed into “green” foams by intensive mechanical stirring, occurred with a limited addition of alkali activator (1 M NaOH). The products coupled the stabilization of pollutants with good mechanical properties (e.g., compressive strength approaching 4 MPa). Interestingly, they could be used also as raw material for new glass-ceramic foams, obtained by the same gel casting and sintering method, with no degradation of chemical stability. Limitations in the crushing strength, derived from the limited viscous flow densification of semi-crystalline powders, were overcome by mixing powders from recycled foams with 30 wt% soda-lime glass. The new products finally featured an even higher strength-to-density ratio than the foams from the first cycle. Full article

This study aims to investigate the physical and chemical characterization of six fly ash samples obtained from different municipal solid waste incinerators (MSWIs), namely grate furnaces, rotary kiln, and fluidized bed reactor, to determine their potential for CO₂ and thermochemical energy storage (TCES). Representative samples were characterized via simultaneous thermal analysis (STA) in different atmospheres, i.e., N₂, air, H₂O, CO₂, and H₂O/CO₂, to identify fly ash samples that can meet the minimum requirements, i.e., charging, discharging, and cycling stability, for its consideration as TCES and CO₂-storage materials and to determine their energy contents. Furthermore, other techniques, such as inductively coupled plasma optical emission spectroscopy, X-ray fluorescence (XRF) spectrometry, X-ray diffraction (XRD), scanning electron microscopy, leachability tests, specific surface area measurement based on the Brunauer–Emmett–Teller method, and particle-size distribution measurement, were performed. XRF analysis showed that calcium oxide is one of the main components in fly ash, which is a potentially suitable component for TCES systems. XRD results revealed information regarding the crystal structure and phases of various elements, including that of Ca. The STA measurements showed that the samples can store thermal heat with energy contents of 50–394 kJ/kg (charging step). For one fly ash sample obtained from a grate furnace, the release of the stored thermal heat under the selected experimental conditions (discharging step) was demonstrated. The cycling stability tests were conducted thrice, and they were successful for the selected sample. One fly ash sample could store CO₂ with a storage capacity of 27 kg CO₂/ton based on results obtained under the selected experimental conditions in STA. Samples from rotary kiln and fluidized bed were heated up to 1150 °C in an N₂ atmosphere, resulting in complete melting of samples in crucibles; however, other samples obtained from grate furnaces formed compacted powders after undergoing the same thermal treatment in STA. Samples from different grate furnaces showed similarities in their chemical and physical characterization. The leachability test according to the standard (EN 12457-4 (2002)) using water in a ratio of 10 L/S and showed that the leachate of heavy metals is below the maximum permissible values for nonhazardous materials (except for Pb), excluding the fly ash sample obtained using fluidized bed technology. The leachate contents of Cd and Mn in the fly ash samples obtained from the rotary kiln were higher than those in other samples. Characterization performed herein helped in determining the suitable fly ash samples that can be considered as potential CO₂-storage and TCES materials. Full article