Search Results (10)

Numerous studies on specific cannabis compounds (cannabinoids and phenolic acids) have demonstrated their therapeutic potential, with their administration methods remaining a key research focus. Transdermal drug delivery (TDD) systems are gaining attention due to their advantages, such as painless administration, controlled release, direct absorption into the bloodstream, and its ability to bypass hepatic metabolism. The thin films obtained via pulsed laser deposition consist of micro- and nanoparticles capable of migrating through skin pores upon contact. This study investigates the interaction of phenolic compounds in hemp seeds with pulsed laser beams. The main goal is to achieve the ablation and deposition of these compounds as thin films suitable for TDD applications. The other key objective is optimizing laser energy to enhance the industrial feasibility of this method. Thin layers were deposited on glass and hemp fabric using dual pulsed laser (DPL) ablation on a compressed hemp seed target held in a stainless steel ring. The target was irradiated for 30 min with two synchronized pulsed laser beams, each with parameters of 30 mJ, 532 nm, pulse width of 10 ns, and a repetition rate of 10 Hz. Each beam had an angle of incidence with the target surface of 45°, and the angle between the two beams was also 45°. To improve laser absorption, two approaches were used: (1) HS-DPL/glass and HS-DPL/hemp fabric, in which a portion of the stainless steel ring was included in the irradiated area, and (2) HST-DPL/glass and HST-DPL/hemp fabric—hemp seeds were mixed with turmeric powder, which is known to improve laser interaction and biocompatibility. The FTIR and Micro-FTIR spectroscopy (ATR) performed on thin films compared to the target material confirmed the presence of hemp-derived phenolic compounds, including tetrahydrocannabinol (THC), cannabidiol (CBD), ferulic acid, and coumaric acid, along with other functional groups such as amides. The ATR spectra have been validated against Gaussian 6 numerical simulations. Scanning electron microscopy (SEM) and substance transfer tests revealed the microgranular structure of thin films. Through the analyzes carried out, the following were highlighted: spherical structures (0.3–2 μm) for HS-DPL/glass, HS-DPL/hemp fabric, HST-DPL/glass, and HST-DPL/hemp fabric; larger spherical structures (8–13 μm) for HS-DPL/glass and HST-DPL/glass; angular, amorphous-like structures (~3.5 μm) for HS-DPL/glass; and crystalline-like structures (0.6–1.3 μm) for HST-DPL/glass. Microparticle transfer from thin films on the hemp fabric to the filter paper at a human body temperature (37 °C) confirmed their suitability for TDD applications, aligning with the “whole plant medicine” or “entourage effect” concept. Granular, composite, thin films were successfully developed, capable of releasing microparticles upon contact with a surface whose temperature is 37 °C, specific to the human body. Each of the microparticles in the thin films obtained with the DPL technique contains phenolic compounds (cannabinoids and phenolic acids) comparable to those in hemp seeds, effectively acting as “microseeds.” The obtained films are viable for TDD applications, while the DPL technique ensures industrial scalability due to its low laser energy requirements. Full article

Flexible fibers, such as biomass particles and glass fibers, are critical raw materials in the energy and composites industries. Assemblies of the fibers show strong interlocking, non-Newtonian and compressible flows, intermittent avalanches, and high energy dissipation rates due to their elongation and flexibility. Conventional mechanical theories developed for regular granular materials, such as dry sands and pharmaceutical powders, are often unsuitable for modeling flexible fibers, which exhibit more complex mechanical behaviors. This article provides a comprehensive review of the current state of research on the mechanics of flexible fiber assemblies, focusing on their behavior under compression, shear flow, and gas–fiber two-phase flow processes. Finally, the paper discusses open issues and future directions, highlighting the need for advancements in granular theories to better accommodate the unique characteristics of flexible fibers, and suggesting potential strategies for improving their handling in industrial applications. Full article

We investigate the choosing of the fractions number for numerical simulation of a polydisperse bubbling fluidized bed using the Sauter mean diameter. The results were verified using experiments from a glass tube with a diameter of 2.2 cm and a height of 50 cm. As a fluidizing agent, air with a velocity of 0.0716 m/s to 0.1213 m/s was used. Polydispersed aluminum oxide particles with a diameter size of 20–140 µm were used as a solid phase. We propose a simple method for choosing the fractions number for the polydispersed granular phase in order to improve the quality of the numerical simulation results. In this study, we consider the Sauter mean diameter D₃₂ for each selected group of particles for the solid phase. By increasing the number of solid phase fractions, it is possible to obtain a mean boundary of the bubbling fluidized bed close to the observed experimental results. In our study, the division of polydispersed powder into four distinct solid-phase fractions enabled us to attain satisfactory agreement with experiments regarding the average value of the bed boundary. Full article

Glass is a substance that is present in most houses since glass-based items are made and consumed in relatively high quantities. This has led to the buildup of glass in concerning quantities all over the world, which is a problem for the environment. It is well known that glass has several advantageous physiochemical features that qualify it as an appropriate material for use in the construction industry as an aggregate. The features include being non-biodegradable, resistant to chemical assault, having low water absorption, having high hydraulic conductivity, having temperature-dependent ductility, having alterable particle gradation, and having a wide availability in a variety of forms and chemical compositions. Because of these qualities, glass has been used in various investigations and field tests conducted in civil engineering to evaluate its effectiveness as an engineering aggregate and to develop environmentally friendly management strategies for waste glass. These studies and research have utilized glass in various forms, such as fine recycled glass, medium recycled glass, coarse recycled glass, powdered glass, and glass-based geopolymers. This study focuses on research studies that present results on physicochemical, mechanical, and durability characteristics. These studies and research contain samples of pure glass or glass as replacement percentages in materials (0–100%), including but not limited to unbound granular materials (such as recycled concrete aggregates and crushed rock). In light of the information assembled in this review article, it is legitimate to claim that glass has strong promise as a material in various civil applications. Full article

The use of recycled waste glass powder (RWGP) as a partial substitute for cement in cement-based materials offers a promising solution for reducing environmental impact and promoting sustainable waste management practices. An experimental study was conducted on a reference material made with Portland-limestone cement CEMII/A-LL42.5R and three other materials containing 50 wt% RWGP with different mean diameters, d₅₀: 16, 18, and 25 µm. The main objective was to analyze the role of RWGP granularity in the short- and medium-term properties of the cement-based materials. The results showed that coarser RWGP granularity led to an increase in fluidity and Portlandite content, while water demand and mechanical properties decreased. However, the range of RWGP granularities tested did not significantly affect the initial setting time, fresh and dry density, hydration temperature, and water porosity. These findings suggest that the choice of RWGP granularity should depend on the desired properties of the cement-based material. Full article

The Nd-Fe-B hot-deformation magnet with high resistivity was successfully prepared by hot-pressing and hot-deformation of Nd-Fe-B fast-quenched powder with amorphous glass fiber. After the process optimization, the resistivity of the magnet was increased from 0.383 mΩ·cm to 7.2 mΩ·cm. Therefore, the eddy current loss of magnets can be greatly reduced. The microstructure shows that the granular glass fiber forms a continuous isolation layer during hot deformation. At the same time, the boundary of Nd-Fe-B quick-quenched the flake and glass fiber from the transition layer, which improves the binding of the two, and which can effectively prevent the spalling of the isolation layer. In addition, adding glass fiber improves the orientation of the hot deformation magnet to a certain extent. The novel design concept of insulation materials provides new insights into the development and application of rare earth permanent magnet materials. Full article

Alkali-activated binders have the potential to consume various types of waste materials. Low initial molar ratios of SiO₂/Al₂O₃ geopolymer mortars were considered in this article. Here we studied alkali-activated binders produced with photovoltaic glass powder in 5%; kaolin clay in 15%; ground granulated blast furnace slag in 30%; alumina-lime cement in 30%; and, interchangeably, fly ash from coal combustion in 5%, fly ash from biomass combustion in 5%, or granulated autoclaved cellular concrete in 5%. The influence of clay dehydroxylation, curing conditions, glass presence, and a kind of waste material was investigated. According to the experimental results, strength (compressive and tensile) gradually increased with increasing time and with the use of calcined clay. Significant improvement in compressive strength was seen with the additional 3 days curing time in 105 °C when non-sintered clay was used. The presence of photovoltaic glass in alkali-activated mortars immobilised mercury and arsenic but released zinc, chromium, and sulphates. The microscopic observations confirmed the greater densification of the microstructure of the binder made of calcined clay due to its greater surface development and dehydroxylation. The binder of non-calcined clay was granular, and the interfacial transitional zone was more porous. The C–A–S–H gel seemed to be the main phase. XRD examination confirmed the presence of C–A–S–H, C–S–H, zeolites, and many other phases in minor amount. The presented research was a pilot study, and its main goal was to develop it further. Full article

Glass-based goods are produced and consumed in relative abundance, making glass a material that is found in most households, thereby leading to its accumulation in alarming quantities throughout the globe and posing an environmental challenge. This being said, glass has been widely acknowledged to possess a variety of desirable physiochemical properties, making it suitable for utilisation as an engineering aggregate. The properties include its non-biodegradable nature, resistance to chemical attack, low water absorption, hydraulic conductivity, temperature-dependent ductility, alterable particle gradation, and its availability in a multitude of forms/chemical compositions. Owing to these properties, glass has been employed in a myriad of civil engineering studies and field trials to assess its efficacy as an engineering aggregate and to provide sustainable management schemes for waste glass. These studies/trials have incorporated glass in many forms, including fine recycled glass (FRG), medium recycled glass (MRG), coarse recycled glass (CRG), glass powder, glass fibres, foamed glass, and glass-based geopolymers. Although the beneficial properties of glass can be exploited in numerous engineering endeavours, this review paper focuses on the possible application of glass to subsurface layers of pavements. In turn, the current study centres on research studies/trials presenting results on the physicochemical, mechanical, and durability aspects of pavement layers (base, subbase, and subgrade) containing pure glass samples or glass as percentage replacements in materials, including but not limited to unbound granular materials (i.e., recycled concrete aggregate (RCA) and crushed rock (CR)) and clay soils. Through the knowledge compiled in this review article, it is reasonable to state that glass shows solid potential as a road pavement material. Full article

Waste glass (WG) is unsustainable due to its nonbiodegradable property. However, its main ingredient is silicon dioxide, which can be utilised as a supplementary cementitious material. Before reusing WG, the flexural strength (FS) and alkali–silica reaction (ASR) expansion of WG concrete are two essential properties that must be investigated. This study produced mortar containing activated glass powder using mechanical, chemical, and mechanical–chemical (combined) approaches. The results showed that mortar containing 30% WG powder using the combined method was optimal for improving the FS and mitigating the ASR expansion. The microstructure analysis was implemented to explore the activation effect on the glass powder and mortar. Moreover, a random forest (RF) model was proposed with hyperparameters tuned by beetle antennae search (BAS), aiming at predicting FS and ASR expansion precisely. A large database was established from the experimental results based on 549 samples prepared for the FS test and 183 samples produced for the expansion test. The BAS-RF model presented high correlation coefficients for both FS (0.9545) and ASR (0.9416) data sets, showing much higher accuracy than multiple linear regression and logistic regression. Finally, a sensitivity analysis was conducted to rank the variables based on importance. Apart from the curing time, the particle granularity and content of WG were demonstrated to be the most sensitive variable for FS and expansion, respectively. Full article

During the past few years, we have studied the granulated silica method as a versatile and cost effective way of fiber preform production and the sol-gel method. Until now, we have used the sol-gel technology together with an iterative re-melting and milling step in order to produce rare earth or transition metal doped granular material for the granulated silica method. Here, we present that the iterative re-melting (laser-assisted) and milling step is no longer needed to reach a high homogeneity. The sol-gel method also offers a high degree of compositional flexibility with respect to dopants; it further facilitates achieving high concentrations, even in cases when several dopants are used. We employed optical active doped sol-gel derived granulate for the fiber core, whereas pure or index-raised granulated silica has been employed for the cladding. Based on the powder-in-tube technique, where silica glass tubes are appropriately filled with these granular materials, fibers has been directly drawn (“fiber rapid prototyping”), or eventually after an additional optional quality enhancing vitrification step. The powder-in-tube technique is also ideally suited for the preparation of microstructured optical fibers. Full article