Search Results (4)

Expansive soils, prone to significant volume changes with moisture fluctuations, challenge engineering infrastructure due to their swelling and shrinking. Traditional stabilization methods, including mechanical and chemical treatments, often have high material and environmental costs. This study explores fibrous by-products of flax processing, a sustainable alternative, for reinforcing expansive clay soil. Derived from the Linum usitatissimum plant, flax fibers offer favorable mechanical properties and environmental benefits. The research evaluates the impact of flax tow (FT) reinforcement on enhancing soil strength and reducing cracking. The results reveal that incorporating up to 0.6% randomly distributed FTs, consisting of technical flax fibers and shives, significantly improves soil properties. The unconfined compressive strength (UCS) increased by 29%, with 0.6% FT content, reaching 525 kPa, compared to unreinforced soil and further flax tow additions, which led to a decrease in UCS. This reduction is attributed to diminished soil–fiber interactions and increased fiber clustering. Additionally, flax tows effectively reduce soil cracking. The crack length density (CLD) decreased by 6% with 0.4% FTs, and higher concentrations led to increased cracking. The crack index factor (CIF) decreased by 71% with 0.4% flax tows but increased with higher FT concentrations. Flax tows enhance soil strength and reduce cracking while maintaining economic and environmental efficiency, offering a viable solution for stabilizing expansive clays in geotechnical applications. Full article

The identification of thermomechanical in-plane shear behavior of preform is one of the most important factors to ensure the quality of the thermoplastic composites during the thermoforming process. In this present work, the non-symmetric in-plane shear behavior of flax/polypropylene 2D biaxial braided preform for thermoplastic biocomposites was characterized at elevated temperature chamber by using bias-extension test. Analytical models of a bias-extension test based on non-symmetric unit cell geometry for 2D biaxial braids were defined and applied; the thermo-condition-dependent experiments were conducted to study the temperature and displacement rate dependences. The influence of unit cell geometry parameters including braiding angle, tow waviness, and cover factor on the thermal in-plane shear behavior was deeply invested, experiments in both axial and transversal directions were performed for a complete study, and asymmetric scissor mechanisms for in-plane shear behavior were introduced and studied. Finally, a simulation of thermal impregnation distribution based on unit cell geometry was made to clarify the importance of the overall fiber volume fraction. Full article

The main objective of this article is to develop ceramic-based materials for additive layer manufacturing (3D printing technology) that are suitable for civil engineering applications. This article is focused on fly ash-based fiber-reinforced geopolymer composites. It is based on experimental research, especially research comparing mechanical properties, such as compressive and flexural strength for designed compositions. The comparison includes various composites (short fiber-reinforced geopolymers and plain samples), different times of curing (investigation after 7 and 28 days), and two technologies of manufacturing (casted and injected samples—simulations of the 3D printing process). The geopolymer matrix is based on class F fly ash. The reinforcements were green tow flax and carbon fibers. The achieved results show that the mechanical properties of the new composites made by injection methods (simulations of 3D technology) are comparable with those of the traditional casting process. This article also discusses the influence of fiber on the mechanical properties of the composites. It shows that the addition of short fibers could have a similar influence on both of the technologies. Full article

There has been a substantial increase in the usage of natural fibers and biodegradable polymers in composite materials due to the recent focus on sustainability of materials. Flax fibers have exhibited higher mechanical properties compared to most other natural fibers available. However, one of the major challenges faced in the use of flax fiber is its hydrophilicity. In this study, the tensile behavior of flax fiber tows removed from commercially available woven fabrics were investigated at different moisture levels. The breaking tenacity of fiber tows was shown to increase with an increase in moisture content of up to 25%. After this point, additional absorption of moisture resulted in a decrease of fiber tenacity. In addition, the diffusion process through flax fiber mat with different areal densities was investigated and the diffusion coefficients were determined using the desorption curves. Diffusion rates were not found to significantly change with varying areal densities of 200 to 400 gsm, but were significantly different when exposed to temperatures of 55 °C versus 80 °C. Full article