Search Results (5)

Coatings can achieve the property of changing color with temperature variations by adding thermochromic microcapsules, which can bring a variable surface to the substrate. Ultraviolet ray (UV)-cured primers have the advantages of a fast curing rate, low-temperature curing, and low pollution. Thermochromic microcapsules can expand the application range of UV primers. Thermochromic microcapsules were synthesized through an orthogonal test, using crystal violet lactone, bisphenol A, and decanol as the core materials in a 1:4:50 mass ratio, with urea formaldehyde resin as the wall material. The effects of the addition of batches of the urea, the mass ratio of the formaldehyde solution to the urea, the hydrophilic–lipophilic balance (HLB) value of the emulsifier, and core-to-wall mass ratio on microcapsules yields, encapsulation rates, thermochromic color differences (ΔE), and formaldehyde releases during synthesis were investigated. The results were normalized, with the thermochromic ΔE as the primary reference for analysis. The results indicate that the HLB value of the emulsifier was the key factor that affected the microcapsule performance. In a single-factor test, the HLB value was adjusted within the range of 6.00 to 10.00. It was found that when the HLB value was 10.00, the microcapsules exhibited the best comprehensive performance, with a yield of 43.29%, an encapsulation rate of 45%, a thermochromic ΔE of 4.60, and a formaldehyde concentration released of 1.310 mg/L. The 11# microcapsules with the optimal morphology and better comprehensive performance were compared with the best 14# microcapsules. Different amounts of these microcapsules were added to the UV primer to investigate the effects of the 11# and 14# microcapsules on the mechanical and optical properties of the UV primer. The main component of the UV primer was polyurethane acrylic resin, propylene glycol diacrylate, and hexanediol diacrylate. When 14# microcapsules were added to the UV primer at a concentration of 10%, the primer exhibited the best comprehensive performance, with a fracture elongation of 17.44%, a roughness of 0.15 μm, and a visible light transmittance of 83%. Microcapsule technology was used to modify UV primers, endowing them with thermochromic properties and expanding the application range of thermochromic microcapsules. Full article

Polyurethanes are gaining increasing interest for their use as structural components subjected to cyclic loads, such as leaf springs. Thermoset polyurethane (PUR) based technology offers some advantages, such as fatigue resistance, low viscosity, and fast curing. However, current PUR formulations present two major drawbacks: their petrochemical origin and high reactivity. The aim of this work was to develop a novel biobased PUR (BIO-PUR) with the required mechanical properties and processability for manufacturing structural composites by resin transfer moulding (RTM). For this purpose, a high functionality and high hydroxyl index castor-oil-based polyol was used combined with a biobased glycerol (BIO-Gly) to increase the crosslinking density and improve the final properties of the BIO-PUR. The viscosity and reactivity of the different systems were studied by means of rheology tests and differential scanning calorimetry (DSC). Thermal and mechanical properties were studied by dynamic mechanical analysis (DMA) and flexural tests. Furthermore, the RTM process of a representative part was simulated and validated through the manufacturing and testing of plates. The properties of the BIO-PUR resin systems were strongly influenced by the addition of biobased glycerol and its effect on the crosslinking density. The combination of a high functionality and hydroxyl index biobased polyol with the biobased glycerol resulted in a high-performance BIO-PUR with the required reactivity and final properties for structural applications. Full article

Novel polymeric coatings, namely slippery polyurethane (SPU) coatings, with high surface hydrophobicity and superior erosion resistance against high speed solid particles and water droplets were successfully developed to protect the leading edge of fast moving aerodynamic structures, such as aircraft wings and rotor blades, against ice accretion. The coatings comprise newly synthesized surface-modifying polymers (SMPs) bearing fluorinated and polydimethylsiloxane branches at a loading level of 1–5 wt.%, based on the total resin solid, which showed good compatibility with the erosion-resistant polyurethane matrix (PU-R) and rendered effective surface hydrophobicity and slipperiness to the coatings, as evidenced by the high water contact angles of 100–115°. The coatings can be easily be sprayed or solution cast and cured at ambient temperature to provide highly durable thin coating films. X-ray photoelectron spectroscopy (XPS) investigation showed concentration of fluorine on the surface. The presence of 1–5 wt.% of SMPs in the polyurethane matrix slightly reduced the tensile modulus but had no significant impact on the tensile strength. All coating films exhibited good thermal stability with no material softening or degradation after heating at 121 °C for 24 h. DSC heating scans revealed no thermal transitions in the temperature range of −80 °C to 200 °C. Ice adhesion strength (IAS) tests using a static push rig in a cold room of −14 °C showed IAS as low as 220 kPa for the SPU coatings, which is much lower than that of PU-R (i.e., about 620 kPa). Sand erosion tests using 50 μm angular alumina particles at an impinging speed of 150 m/s and an impinging angle of 30° revealed very low erosion rates of ca. 100 μg/g sand for the coatings. Water droplet erosion tests at 175 m/s using 463 μm droplets with 42,000 impingements every minute showed no significant coating removal after 20 min of testing. The combination of the high surface hydrophobicity, low ice adhesion strength and superior erosion resistance makes the SPU coatings attractive for ice protection of aircraft structures, where the coatings’ erosion durability is of paramount importance. Full article

In this contribution, the influence of the reaction injection moulding process on the thermomechanical material behaviour of aliphatic hexamethylene diisocyanate (HDI) based fast curing polyurethane is demonstrated. Uniaxial tensile tests, temperature-frequency dependent dynamic mechanical thermal analysis (DMTA) and Differential Scanning Calorimetry (DSC) are used to show the differences in properties for ten different sets of process parameters. The mould and resin components temperature, the mass flow during the filling process and the residence time during the reaction process of the polyurethane are varied in several stages. Further experiments to determine the molar mass of the molecular chain between two crosslinking points of the polyurethane are used to explain the process influences on the thermomechanical properties. Thus, a direct correlation between manufacturing and material properties is shown. In addition, the mutual effect of the different parameters and their overall influence on the material behaviour is presented. Full article

In this work, the characterisation of reaction kinetics of a methylene diphenyl diisocyanate (MDI)-based fast curing polyurethane resin (PUR) and the mathematical description of its curing process are presented. For the modelling of the reaction process isoconversional methods, which are also called model-free approaches, are used instead of model-based approaches. One of the main challenges is the characterisation of a reactive system with a short pot life, which already starts to crosslink below room temperature. The main focus is the evaluation of the applicability of isoconversional methods for predicting the reaction kinetics of fast curing polyurethane resins. In order to realise this, a repeatable methodology for the determination of time- and temperature-dependent reaction curves using differential scanning calorimetry (DSC) is defined. The cure models defined by this method serve as the basis for process simulations of PUR processing technologies such as resin transfer moulding (RTM) or reactive injection moulding (RIM) and reactive extrusion (REX). The characterisation of the reaction kinetics using DSC measurements is carried out under isothermal and non-isothermal conditions. Within this work isoconversional methods have been applied successfully to experimentally determined DSC data sets. It is shown that the reaction kinetics of fast curing polyurethane resins can be predicted using this methods. Furthermore, it is demonstrated that the time-dependent change of conversion of the considered polyurethane under isothermal curing conditions can also be predicted using isoconversional methods based on non-isothermal DSC measurements. This results in a significant reduction in the experimental effort required to characterise and model the curing process of polyurethanes. Full article