Search Results (3)

In this study, a method for producing nitrogen-modified graphene oxide (NMGO) using hydrothermal synthesis in the presence of triethanolamine is presented. The composition and structure of NMGO are characterized using X-ray phase analysis (XPA), scanning electron microscopy (SEM), Fourier transform infrared spectroscopy, and Raman spectroscopy. Ni-based metal matrix coatings (MMCs) modified with NMGO were obtained from a sulfate-chloride electrolyte in the galvanostatic mode. The process of electrochemical deposition of these coatings was studied using chronovoltammetry. The microstructure of Ni–NMGO MMCs was studied using the XPA and SEM methods. It has been established that the addition of NMGO particles into the Ni matrix results in an increase in the microhardness of the resulting coatings by an average of 1.30 times. This effect is a consequence of the refinement of crystallites and high mechanical properties of NMGO phase. The corrosion-electrochemical behavior of studied electrochemical deposits in 0.5 M sulfuric acid was analyzed. It has been shown that the corrosion rate of Ni–NMGO MMCs in a 3.5% sodium chloride environment decreases by approximately 1.50–1.70 times as compared to unmodified Ni coatings. This is due to NMGO particles that act as a barrier preventing the propagation of the corrosion and form corrosive galvanic microelements with Ni, promoting anodic polarization. Full article

In this study, we used multilayer graphene oxide (GO) obtained by anodic oxidation of graphite powder in 83% sulfuric acid. The modification of GO was carried out by its interaction with hexamethylenediamine (HMDA) according to the mechanism of nucleophilic substitution between the amino group of HMDA (HMDA) and the epoxy groups of GO, accompanied by partial reduction of multilayer GO and an increase in the deformation of the carbon layers. The structure and properties of modified HMDA-GO were characterized using research methods such as scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction spectroscopy and Raman spectroscopy. The conducted studies show the effectiveness of using HMDA-OG for modifying epoxy composites. Functionalizing treatment of GO particles helps reduce the free surface energy at the polymer–nanofiller interface and increase adhesion, which leads to the improvement in physical and mechanical characteristics of the composite material. The results demonstrate an increase in the strength and elastic modulus in bending by 48% and 102%, respectively, an increase in the impact strength by 122%, and an increase in the strength and elastic modulus in tension by 82% and 47%, respectively, as compared to the pristine epoxy composite which did not contain GO-HMDA. It has been found that the addition of GO-HMDA into the epoxy composition initiates the polymerization process due to the participation of reactive amino groups in the polymerization reaction, and also provides an increase in the thermal stability of epoxy nanocomposites. Full article

Some solid solutions with the chemical composition K_xFe_yTi_8-yO₁₆ (KFTO) and a hollandite-like structure were successfully synthesized by modified sol–gel method. The obtained powders were characterized using X-ray diffraction (XRD) and scanning electron microscopy (SEM). The ceramic pellets based on KFTO powders were obtained by compressing and sintering at 1080 °C for 4 h. The sinters were characterized by X-ray and impedance spectroscopy. XRD results show that KFTO powders have a mono-phase tetragonal structure at x = 1.4–1.8 and y = 1.4–1.6. However, it was recognized that the hollandite-like phase could be broken during sintering to form TiO₂ and Fe₂TiO₅ crystals distributed throughout the volume of the ceramics. A frequency dependency of dielectric properties for the sinters was studied by impedance spectroscopy. It was found that an increase in the TiO₂ (rutile) phase during the sintering contributes to a decrease in dielectric losses. At the same time, the KFTO ceramics with reduced content of potassium had increased permittivity. The contribution of electron-pinned defect dipoles (EPDD) and internal barrier layer capacitance (IBLC) in the permittivity of the obtained ceramics was estimated using the Havriliak–Negami equation. It is shown that the KFTO ceramics have the polydisperse characteristic of dielectric relaxation. The observed grain and grain boundary dipole relaxation times were 1.03 × 10⁻⁶ to 5.51 × 10⁻⁶ s and 0.197 to 0.687 s, respectively. Full article