Search for Articles:
Title / Keyword
Author / Affiliation / Email
Journal
Article Type
 
 
Advanced Search
 
Section
Special Issue
Volume
Issue
Number
Page
 
5.5
3.2
Journals
Energies
Special Issues
Experimental Heat Transfer in Energy Systems
energies-logo
Submit to Energies Review for Energies Propose a Special Issue

Journal Menu

► Journal Menu

Journal Browser

► Journal Browser
share announcement

Experimental Heat Transfer in Energy Systems

A special issue of Energies (ISSN 1996-1073). This special issue belongs to the section "J: Thermal Management".

Deadline for manuscript submissions: closed (30 September 2020) | Viewed by 57699

Special Issue Editors

Prof. Dr. Yao-Hsien Liu

E-Mail Website
Guest Editor
Department of Mechanical Engineering, National Chiao Tung University, Hsinchu 300, Taiwan
Interests: thermodynamics; heat transfer; heat convection; gas turbine cooling technology; experimental methods in heat transfer and fluid mechanics
Prof. Dr. Chi-Chuan Wang

E-Mail Website
Guest Editor
Department of Mechanical Engineering, National Chiao Tung University, Hsinchu 300, Taiwan
Interests: energy-thermofluids engineering; micro/nano engineering

Special Issue Information

Dear Colleagues,

This is a call for papers of a Special Issue on “Experimental Heat Transfer in Energy Systems”. Over the last 50 years, experimental investigation on heat transfer has served as a fundamental basis in analytical modeling and numerical simulation. Experimental investigation is also quite essential in proving the applicability either in complex energy systems or some simple novel conceptions. The objective of this Special Issue is to present recent advances in all areas of experimental heat transfer studies in energy systems, energy conservation, energy storage, and other energy research. With the rapid development of technology in energy, particularly in relation to heat transfer, sufficient experimental data to evaluate the impact of emerging technology has become imperative.

Main topics of interest include, but not limited to, the following:

  • Thermal management at all scales (nano, micro, and macro) and in all types of energy systems
  • Heat transfer and fluid flow in turbomachinery, organic ranking cycle, HVAC and R system and other energy technologies
  • Convective heat transfer in single phase and multiphase flow
  • Cooling designs/applications for electronics (chip, PCB, module, rack, heat pipe, data center, etc.)
  • The heat transfer enhancement technique and energy saving
  • Phase change material and thermal energy storage
  • Thermal issues in energy conversion

Assoc. Prof. Yao-Hsien Liu
Prof. Dr. Chi-Chuan Wang
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Energies is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Experimental heat transfer
  • Thermal management
  • Heat transfer enhancement
  • Energy system
  • Energy saving
  • Energy conversion
  • Electronic cooling

Published Papers (18 papers)

Download All Papers
Order results
Result details
Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:

Research

Jump to: Other

13 pages, 4082 KiB  
Article
Numerical and Experimental Study of Air-to-Air Plate Heat Exchangers with Plain and Offset Strip Fin Shapes
by Kyung Rae Kim, Jae Keun Lee, Hae Do Jeong, Yul Ho Kang and Young Chull Ahn
Energies 2020, 13(21), 5710; https://doi.org/10.3390/en13215710 - 31 Oct 2020
Cited by 9 | Viewed by 2659
Abstract
This study evaluates the performance of a plate heat exchanger numerically and experimentally. The predictive model for estimating the heat transfer and frictional pressure drop across the plain and offset strip fins is compared with the experimental results with the parameters of Reynolds [...] Read more.
This study evaluates the performance of a plate heat exchanger numerically and experimentally. The predictive model for estimating the heat transfer and frictional pressure drop across the plain and offset strip fins is compared with the experimental results with the parameters of Reynolds number and fin pitch. The heat transfer of the offset fin shape is 13.4% higher than that of the plain fin in the experiment in the case of Re = 6112 for the hot airflow and Re = 2257 for the cold airflow. A predictive model uses the effectiveness-Number of Transfer Units (NTU) method with the discretization in the segments divided into small control volumes in the heat exchanger. The difference of heat transfer and pressure drop for the plain fin between the numerical and the experimental results are approximately 1.9% and 5.9%, respectively. Thus, the results indicate that the predictive model for estimating the heat transfer is useful for evaluating the performance of the plate heat exchanger in the laminar-to-transition regions. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

15 pages, 3348 KiB  
Article
Experimental Investigation of the Thermofluid Characteristics of Shell-and-Plate Heat Exchangers
by Howard Lee, Ali Sadeghianjahromi, Po-Lun Kuo and Chi-Chuan Wang
Energies 2020, 13(20), 5304; https://doi.org/10.3390/en13205304 - 12 Oct 2020
Cited by 14 | Viewed by 2756
Abstract
An experimental study regarding the thermofluid characteristics of a shell-and-plate heat exchanger with different chevron angles (45°/45°, 45°/65°, and 65°/65°) with a plate diameter of 440 mm was carried out. Water was used as the working fluid on both sides and the corresponding [...] Read more.
An experimental study regarding the thermofluid characteristics of a shell-and-plate heat exchanger with different chevron angles (45°/45°, 45°/65°, and 65°/65°) with a plate diameter of 440 mm was carried out. Water was used as the working fluid on both sides and the corresponding temperatures ranged from 30–70 °C. The flow rate on the plate or shell side ranged from 10–60 m3/h. The effects of chevron angles on the heat transfer and fluid flow characteristics of shell-and-plate heat exchangers were studied in detail. With regard to the heat transfer performance on the plate side, a higher chevron angle (65°/65°) resulted in a significantly better performance than a low chevron angle (45°/45°). The effect of the chevron angle became even more pronounced at high Reynolds numbers. Unlike the plate side, an increase in the chevron angle had a negative effect on the heat transfer performance of the shell side. Additionally, this opposite effect was more prominent at low Reynolds numbers due to the comparatively large contribution of the manifold. The friction factor increased appreciably with the increase in the chevron angle. However, when changing the chevron angle from 45°/45° to 65°/65°, the increase in the friction factor was about 3–4 times on the plate side while it was about 2 times on the shell side. This can be attributed to the presence of the distribution/collection manifold on the shell side. Empirical correlations for the Nusselt number and friction factor were developed for different combinations of chevron angles with mean deviations of less than 1%. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

17 pages, 5646 KiB  
Article
Heat Transfer Enhancement of Plate-Fin Heat Sinks with Different Types of Winglet Vortex Generators
by Jin-Cherng Shyu and Jhao-Siang Jheng
Energies 2020, 13(19), 5219; https://doi.org/10.3390/en13195219 - 07 Oct 2020
Cited by 6 | Viewed by 2430
Abstract
Because the delta winglet in common-flow-down configuration has been recognized as an excellent type of vortex generators (VGs), this study aims to experimentally and numerically investigate the thermo-hydraulic performance of four different forms of winglet VGs featuring sweptback delta winglets in the channel [...] Read more.
Because the delta winglet in common-flow-down configuration has been recognized as an excellent type of vortex generators (VGs), this study aims to experimentally and numerically investigate the thermo-hydraulic performance of four different forms of winglet VGs featuring sweptback delta winglets in the channel flow in the range 200 < Re < 1000. Both Nusselt number and friction factor of plate-fin heat sinks having different forms of winglets, including delta winglet pair (DWP), rectangular winglet pair (RWP), swept delta winglet pair (SDWP), and swept trapezoid winglet pair (STWP), were measured in a standard wind tunnel without bypass in this study. Four rows of winglets with in-line arrangement were punched on each 10-mm-long, 0.2-mm-thick copper plate, and a total of 16 pieces of copper plates with spacing of 2 mm were fastened together to achieve the heat sink. The projected area, longitudinal and winglet tip spacing, height and angle of attack of those winglets were fixed. Besides that, three-dimensional numerical simulation was also performed in order to investigate the temperature and fluid flow over the plate-fin. The results showed that the longitudinal, common-flow-down vortices generated by the VGs augmented the heat transfer and pressure drop of the heat sink. At airflow velocity of 5 m/s, the heat transfer coefficient and pressure drop of plain plate-fin heat sink were 50.8 W/m2·K and 18 Pa, respectively, while the heat transfer coefficient and the pressure drop of heat sink having SDWP were 70.4 W/m2·K and 36 Pa, respectively. It was found that SDWP produced the highest thermal enhancement factor (TEF) of 1.28 at Re = 1000, followed by both RWP and STWP of similar TEF in the range 200 < Re < 1000. The TEF of DWP was the lowest and it was rapidly increased with the increase of airflow velocity. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

15 pages, 4371 KiB  
Article
Evaluation of the Ignition Effect in Constant Volume Combustion Chamber Based on Matching Effect of High Voltage (MEHV) Method
by Kwonse Kim, Jaeyoung Han and Seokyeon Im
Energies 2020, 13(19), 5084; https://doi.org/10.3390/en13195084 - 29 Sep 2020
Cited by 5 | Viewed by 2980
Abstract
The characteristics of spark ignition with a constant volume combustion chamber (CVCC) is evaluated for the efficiency of capacitive-assisted ignition (CAI), such as spark kernel and flame growth. The conventional spark method and matching effect of high voltage (MEHV) method are evaluated to [...] Read more.
The characteristics of spark ignition with a constant volume combustion chamber (CVCC) is evaluated for the efficiency of capacitive-assisted ignition (CAI), such as spark kernel and flame growth. The conventional spark method and matching effect of high voltage (MEHV) method are evaluated to compare the spark growth distribution characteristics. To do this study, a plasma system is used and is consisted of input power, three capacitors, a transformer, high voltage cable, J-type of a spark plug, diode, and CVCC. The experiment is conducted under various operating conditions, such as 1 bar, 295 K of initial temperature, 50, 100, 150 V of ignition box, 400 V of MEHV, 0.7 ms of spark duration, and 0 kΩ of plug resistor. The results show that the spark growth at the initial voltages of 100 V and 150 V has the same characteristic, and the surface area is increased by 13 mm2 at 150 V compared to 100 V because capacitance energy stored in three capacitors is efficiently induced by the effect of dielectric breakdown and electron collision. Consequently, the spark growth of MEVH is widely distributed atmospheric more than the conventional spark, and the internal temperature of the spark kernel could be presumed to change the non-thermal plasma to thermal plasma by MEHV. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

16 pages, 3934 KiB  
Article
Non-Uniform Three-Dimensional Pulsating Heat Pipe for Anti-Gravity High-Flux Applications
by Chih-Yung Tseng, Kai-Shing Yang and Chi-Chuan Wang
Energies 2020, 13(12), 3068; https://doi.org/10.3390/en13123068 - 13 Jun 2020
Cited by 12 | Viewed by 2138
Abstract
This study proposes a novel high-flux pulsating heat pipe that can lift the major constraint of the conventional pulsating heat pipe (PHP) which is unable to function properly upon anti-gravity operations. The proposed PHP introduces additional unbalance force via uneven tube diameter/geometry in [...] Read more.
This study proposes a novel high-flux pulsating heat pipe that can lift the major constraint of the conventional pulsating heat pipe (PHP) which is unable to function properly upon anti-gravity operations. The proposed PHP introduces additional unbalance force via uneven tube diameter/geometry in the adiabatic sections to tailor the problem in anti-gravity operation. The design contains a three-dimensional configuration circuitry with compact arrangement tubes on the evaporator and condenser. Through this design, the non-uniform three-dimensional pulsating heat pipe (3D-PHP) manipulates the uneven inner diameters of the adiabatic sections to form uneven vapor/liquid distributions in the adiabatic sections to yield a unitary flow pattern that is able to withstand a much higher input power. The present PHP uses methanol as working fluid, with 38% volumetric filling ratio, and has a high-flux of 22.9 W/cm2 and a low the thermal resistance ratio (Ranti-gravity/Rgravity-assisted) of 1.05 when the input power is 800 W. Both the heat flux and thermal resistance ratio for the proposed design are far better than the existing literature. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

20 pages, 2944 KiB  
Article
Enhanced Cooling of LED Filament Bulbs Using an Embedded Tri-Needle/Ring Ionic Wind Device
by Chunlin Xu, Huai Zheng, Jie Liu, Jingcao Chu, Xiaoliang Zeng, Rong Sun and Sheng Liu
Energies 2020, 13(11), 3008; https://doi.org/10.3390/en13113008 - 11 Jun 2020
Cited by 6 | Viewed by 2506
Abstract
Improving the heat dissipation ability for light-emitting diode (LED) filament bulb is very difficult. A tri-needle/ring ionic wind generator was developed to improve the heat dissipation condition of bulbs. The operation characteristics of the ionic wind generator, such as the electrode gap, inception [...] Read more.
Improving the heat dissipation ability for light-emitting diode (LED) filament bulb is very difficult. A tri-needle/ring ionic wind generator was developed to improve the heat dissipation condition of bulbs. The operation characteristics of the ionic wind generator, such as the electrode gap, inception voltage, and discharge current with regard to the operation voltage, were studied by experiments. The ionic wind velocity within the bulb was investigated under different electrode gaps and applied voltages. The temperature drop achieved by the ionic was were tested with the consideration of many operation parameters for analysis. The experiments showed that ionic wind can provide efficient and stable cooling effect for LED filament bulbs. The temperature drop of LED junction can reach 30 °C at best. Good stability and adjustability of the ionic wind generator were demonstrated by tracing the temperature history of LED filaments in long-term tests. Finally, the light efficiency of LED filament bulbs with ionic wind cooling was studied. The experimental results showed that light efficiency was improved by 7.3% under the best cooling case. The experimental results indicate that the embedded ionic wind generator can provide an effective solution for cooling LED filament bulbs. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Graphical abstract

16 pages, 4137 KiB  
Article
Nucleate Pool Boiling Heat Transfer from High-Flux Tube with Dielectric Fluid HFE-7200
by Abhishek Kumar, Kuo-Shu Hung and Chi-Chuan Wang
Energies 2020, 13(9), 2313; https://doi.org/10.3390/en13092313 - 06 May 2020
Cited by 12 | Viewed by 3369
Abstract
In the present experimental study, nucleate pool boiling heat transfer measurements of two high-flux tubes (sample A and sample B) were conducted at atmospheric pressure with HFE-7200 as the working fluid. Both high-flux tubes were made from a sintered Cu-Ni (high-flux) alloy powder. [...] Read more.
In the present experimental study, nucleate pool boiling heat transfer measurements of two high-flux tubes (sample A and sample B) were conducted at atmospheric pressure with HFE-7200 as the working fluid. Both high-flux tubes were made from a sintered Cu-Ni (high-flux) alloy powder. The porous high-flux surface was coated inside the test tube and it is tested within the heat flux ranging from 2.6 to 86 kW/m2. The major difference between sample A and sample B was the coating thickness, where sample B (0.6 mm) was much larger than that of sample A (0.07 mm). Both tubes showed about three times enhancement in heat transfer coefficient (HTC) when compared to plain tube. Even though sample B contained a higher HTC than sample A, it also revealed a faster level-off phenomenon regarding the HTC vs. wall superheat. The major parameter which characterizes the boiling performance of high-flux tube was the ratio of coating thickness to pore diameter which also yielded different trends upon HTC vs. wall superheat amid sample A and B. It was found that the porous based Nishikawa correlation can well predict the performance of sample A but not sample B. This is because the ratio of coating thickness to pore diameter is far outside the applicable range of the Nishikawa correlation. Hence, a modified Nishikawa correlation is proposed. The predicted capability of the proposed modified Nishikawa correlation against sample A and sample for HTC was within ±28% deviation. The standard mean deviation of the Nishikawa correlation with experimental data for sample A and sample B was 0.302 (12.48%) and 5.64 (73%), respectively. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

21 pages, 2854 KiB  
Article
A Criterion of Heat Transfer Deterioration for Supercritical Organic Fluids Flowing Upward and Its Heat Transfer Correlation
by Yung-Ming Li, Jane-Sunn Liaw and Chi-Chuan Wang
Energies 2020, 13(4), 989; https://doi.org/10.3390/en13040989 - 22 Feb 2020
Cited by 3 | Viewed by 2823
Abstract
The main objective of this study was to develop the supercritical heat transfer correlation applicable for organic fluids when flowing upward in smooth tubes based on the available experimental data. The organic fluids contain R-22, R-134a, R-245fa and Ethanol and the associated heat [...] Read more.
The main objective of this study was to develop the supercritical heat transfer correlation applicable for organic fluids when flowing upward in smooth tubes based on the available experimental data. The organic fluids contain R-22, R-134a, R-245fa and Ethanol and the associated heat transfer characteristics were compared with non-organic fluids like water and carbon-dioxide (CO2). It was found that the limit heat flux may result in heat transfer deterioration (HTD) of organic fluid and the corresponding values are much smaller than water or CO2. A new criterion to predict the HTD was developed and this criterion yields the best predictive ability against database. It was found that HTD occurs can be well described by the acceleration parameter evaluated at the wall condition rather than at bulk condition. For estimation of the supercritical heat transfer coefficient (HTC) for organic fluid, the present study proposes a new correlation with a physically based correction factor, which gives satisfactory predictions against the HTC of supercritical organic fluid. The new correlation can offer the smallest average deviation of 0.007 and standard deviation of 0.181 among the existing correlations. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

19 pages, 7046 KiB  
Article
Visualization of Patterned Modified Surfaces in Condensation and Frosting States
by Kai-Shing Yang, Wei Lu and Yu-Lieh Wu
Energies 2019, 12(23), 4471; https://doi.org/10.3390/en12234471 - 23 Nov 2019
Cited by 6 | Viewed by 2622
Abstract
In this study, a novel, thorn-shaped, containing, hydrophilic, and hydrophobic surface is proposed to have a better condensate drainage characteristic and to delay the required time for frosting. By using a hydrophilic and hydrophobic mixed thorn-shaped surface created by screen printing, the design [...] Read more.
In this study, a novel, thorn-shaped, containing, hydrophilic, and hydrophobic surface is proposed to have a better condensate drainage characteristic and to delay the required time for frosting. By using a hydrophilic and hydrophobic mixed thorn-shaped surface created by screen printing, the design makes use of the differences in the wettability gradient to achieve rapid condensate drainage and to lengthen the time for frosting. The results of a frosting experiment indicated that the droplet adsorption and combination and discharge effect in the thorn sample were substantial. The drainage effect increased the surface renewal rate and inhibited ice layer growth on the thorn sample by 52.4% compared with that on pure copper surface. The heat transfer coefficient of the thorn sample during frosting was approximately 16.2% higher than that of pure copper surface. In addition, the defrosting results indicated that the defrosting time of the thorn sample was almost equal to that of the pure copper sample. However, large droplets were easily stagnated at the structural junction due to contact angle hysteresis after defrosting. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Graphical abstract

18 pages, 6144 KiB  
Article
Enhancement of Mist Flow Cooling by Using V-Shaped Broken Ribs
by Kuan-Tzu Huang and Yao-Hsien Liu
Energies 2019, 12(19), 3785; https://doi.org/10.3390/en12193785 - 06 Oct 2019
Cited by 6 | Viewed by 2199
Abstract
Substantial heat transfer enhancement can be achieved by cooling with air/water mist flow because of droplet impingement and liquid film/fragment evaporation on the heated surface, which leads to a high heat-removal rate. An experimental investigation was conducted in a square channel with continuous [...] Read more.
Substantial heat transfer enhancement can be achieved by cooling with air/water mist flow because of droplet impingement and liquid film/fragment evaporation on the heated surface, which leads to a high heat-removal rate. An experimental investigation was conducted in a square channel with continuous and broken V-shaped ribs. To generate a mist flow, micro droplets were introduced into the gas stream. The rib angle of attack was 45°, and the rib spacing-to-height ratios were 10 and 20. The air Reynolds number ranged from 7900 to 24,000, and the water-to-air volume flow ratio was less than 0.1%. The net heat inputs ranged from 1.1–3.1 W/cm2 and 3.4–9.4 W/cm2 for the air and mist flow cases, respectively. Because the deposited liquid fragments produced uneven temperature distribution on the heated surface, steady-state infrared thermography was used to visualize the heat transfer distribution. Two to seven times higher heat transfer was attained for the broken ribs when using the mist flow than when using air flow. This increase was mainly attributed to the broken structure, which facilitated liquid transport and enhanced liquid coverage. In addition, the broken ribs produced a smaller friction factor than continuous ribs. The broken structures were beneficial for higher thermal performance in the mist flow. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

24 pages, 3494 KiB  
Article
Thermophysical Properties Estimation in Annealing Process Using the Iterative Dynamic Programming Method and Gradient Method
by Milan Durdán, Ján Kačur, Marek Laciak and Patrik Flegner
Energies 2019, 12(17), 3267; https://doi.org/10.3390/en12173267 - 25 Aug 2019
Cited by 3 | Viewed by 2062
Abstract
In annealing, steel coils should be heated and consequently cooled according to the technological prescription defined for the annealed type of steel. It is appropriate to develop the systems and methods for estimation of the steel coil inner temperature for that reason. The [...] Read more.
In annealing, steel coils should be heated and consequently cooled according to the technological prescription defined for the annealed type of steel. It is appropriate to develop the systems and methods for estimation of the steel coil inner temperature for that reason. The proposal for such a system of indirect measurement of inner temperature is described in this study. This system, in the form of the mathematical model, is developed based on the theory of heat transfer and needs thermophysical parameters as inputs. In many cases, the thermophysical properties are difficult to access or unknown for the specific composition of the material being processed. In this paper, two optimization methods were applied to estimate two thermophysical properties. The application of the iterative dynamic programming method is aimed to estimate optimal thermal diffusivity. The verification of this method was performed on 11 laboratory measurements. The algorithm of the gradient method was used for estimating thermal conductivity and was verified on seven operational measurements. Results show that the optimized values of thermophysical properties increased the accuracy of the steel coil inner temperature estimation in the locations nearer to the steal coil central axis. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

26 pages, 16108 KiB  
Article
Experimental and Numerical Investigations on Heat Transfer of Bare Tubes in a Bubbling Fluidized Bed with Respect to Better Heat Integration in Temperature Swing Adsorption Systems
by Hannes Vogtenhuber, Dominik Pernsteiner and René Hofmann
Energies 2019, 12(14), 2646; https://doi.org/10.3390/en12142646 - 10 Jul 2019
Cited by 17 | Viewed by 4491
Abstract
In this paper experimental and numerical investigations on heat transfer within a bubbling fluidized bed will be presented with respect to better heat integration in continuous temperature swing adsorption (TSA) processes for biogas upgrading. In the literature, mainly heat transfer measurements with glass [...] Read more.
In this paper experimental and numerical investigations on heat transfer within a bubbling fluidized bed will be presented with respect to better heat integration in continuous temperature swing adsorption (TSA) processes for biogas upgrading. In the literature, mainly heat transfer measurements with glass or sand particles are carried out, thus special reference measurements with adsorbent material in a fluidized bed are missing. Therefore firstly, a series of experiments were carried out in the fluidized bed test facility to obtain heat transfer coefficients between tube surface and bed which were then compared to calculated heat transfer coefficients to determine whether suitable models were available. Horizontal bare tubes with different arrangements (i.e., single tubes and especially tube bundles) are immersed in fluidized amine layered particles with a mean diameter of 650 μ m which are used in the adsorption industry as adsorbent. The test facility enables a cross-current flow of the solids and gas phase as it prevails in a multi-stage fluidized bed reactor for TSA-applications. The heat transfer measurements with different arrangements and adsorbent material show very similar values in the range of 200 W/m 2 K. The mathematical model for single tubes multiplied by a tube diameter factor shows approximate agreement with the experimental results. However, the mathematical models for tube bundles were not able to predict the measured heat transfer coefficients with the required accuracy. Secondly, a computer fluid dynamics (CFD) program was used to perform a numerical investigation of the test facility using the Euler–Euler method in order to describe the required two-phase characteristic of a fluidized bed. The results of the numerical simulation were compared and validated with the experimental results. Bubbling fluidized bed flow regimes could be reproduced well but the heat transfer coefficients between tube and bed were clearly underestimated. However, a numerical study for a bubbling fluidized bed with external circulation, as used in novel continuous TSA systems, could be carried out and thus a tool for better heat integration measures was developed. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

14 pages, 5321 KiB  
Article
Emissivity Characteristics of Hydrocarbon Flame and Temperature Measurement by Color Image Processing
by Junyi Lin, Xiangyu Zhang, Kaiyun Liu and Wenjie Zhang
Energies 2019, 12(11), 2185; https://doi.org/10.3390/en12112185 - 07 Jun 2019
Cited by 6 | Viewed by 4128
Abstract
Non-gray radiation should be considered in the temperature and emissivity measurements of hydrocarbon flames. In this paper an improved ratio pyrometry by spectral analysis and color image processing is proposed. A Newton-type iterative method is utilized to analyze the spectrometer signals for the [...] Read more.
Non-gray radiation should be considered in the temperature and emissivity measurements of hydrocarbon flames. In this paper an improved ratio pyrometry by spectral analysis and color image processing is proposed. A Newton-type iterative method is utilized to analyze the spectrometer signals for the detection of monochromatic emissivity, and then the ratio pyrometry based on color image processing is corrected by the detected monochromatic emissivity without making approximations of the filter profiles of CCD camera. The experiments were conducted on a tubular heating furnace with coal gas and a propane flame. The spectral and spatial distributions of emissivity of hydrocarbon flame were detected, and the temperature measurement results at four conditions coincided with the thermocouple with relative errors less than 8.34%. The soot volume fractions in the turbulent diffusion hydrocarbon flame were approximately estimated from the detected emissivity, and are influenced by the O/C in the combustion. This study will provide a simple and effective method for the detection of non-gray radiation of hydrocarbon flames in the combustion industry. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

12 pages, 2081 KiB  
Article
H2O2-Enhanced Shale Gas Recovery under Different Thermal Conditions
by WeiGang Yu, Jiang Lei, Tengxi Wang and Wei Chen
Energies 2019, 12(11), 2127; https://doi.org/10.3390/en12112127 - 03 Jun 2019
Cited by 5 | Viewed by 2243
Abstract
The permeability of tight shale formations varies from micro-Darcy to nano-Darcy. Recently, hydrogen peroxide (H2O2) was tested as an oxidizer to remove the organic matter in the rock in order to increase shale permeability. In this study, shale particles [...] Read more.
The permeability of tight shale formations varies from micro-Darcy to nano-Darcy. Recently, hydrogen peroxide (H2O2) was tested as an oxidizer to remove the organic matter in the rock in order to increase shale permeability. In this study, shale particles were reacted with hydrogen peroxide solutions under different temperature and pressure conditions in order to “mimic” underground geology conditions. Then, low-temperature nitrogen adsorption and desorption experiments were conducted to measure the pore diameters and porosity of raw and treated shale samples. Moreover, scanning electron microscopy (SEM) images of the samples were analyzed to observe pore structure changes on the surface of shale samples. From the experiments, it was found that the organic matter, including extractable and solid organic matter, could react with H2O2 under high temperature and pressure conditions. The original blocked pores and pore throats were reopened after removing organic matter. With the increase of reaction temperature and pressure, the mean pore diameters of the shale samples decreased first and then increased afterwards. However, the volume and Brunauer–Emmett–Teller (BET) surface areas of the shale particles kept increasing with increasing reaction temperature and pressure. In addition to the effect of reaction temperature and pressure, the pore diameter increased significantly with the increasing reaction duration. As a result, H2O2 could be used to improve the shale permeability. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

29 pages, 12796 KiB  
Article
Prediction of Bubble Departure in Forced Convection Boiling with a Mechanistic Model That Considers Dynamic Contact Angle and Base Expansion
by Hamed Setoodeh, Wei Ding, Dirk Lucas and Uwe Hampel
Energies 2019, 12(10), 1950; https://doi.org/10.3390/en12101950 - 21 May 2019
Cited by 15 | Viewed by 5062
Abstract
A mechanistic model for bubble dynamics in flow boiling that is based on a force balance approach for a growing bubble is introduced. It considers the evaporation of the microlayer underneath the bubble, thermal diffusion and condensation around the bubble cap as well [...] Read more.
A mechanistic model for bubble dynamics in flow boiling that is based on a force balance approach for a growing bubble is introduced. It considers the evaporation of the microlayer underneath the bubble, thermal diffusion and condensation around the bubble cap as well as dynamic inclination and contact angles between the bubble and the heating wall. It requires no recalibration of parameters to predict the bubble growth. Validation against different experimental flow boiling data was carried out with no case-dependent recalibration and yielded good agreement. The simulations confirmed the dependency of bubble departure and lift-off diameters on different parameters such as heat flux, liquid properties, subcooling temperature, system pressure, inclination angle of channel, channel geometry and mass flow rate. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

17 pages, 3501 KiB  
Article
Thermal Assessment of Nano-Particulate Graphene-Water/Ethylene Glycol (WEG 60:40) Nano-Suspension in a Compact Heat Exchanger
by M. M. Sarafraz, Mohammad Reza Safaei, Zhe Tian, Marjan Goodarzi, Enio Pedone Bandarra Filho and M. Arjomandi
Energies 2019, 12(10), 1929; https://doi.org/10.3390/en12101929 - 20 May 2019
Cited by 108 | Viewed by 4311
Abstract
In the present study, we report the results of the experiments conducted on the convective heat transfer of graphene nano-platelets dispersed in water-ethylene glycol. The graphene nano-suspension was employed as a coolant inside a micro-channel and heat-transfer coefficient (HTC) and pressure drop (PD) [...] Read more.
In the present study, we report the results of the experiments conducted on the convective heat transfer of graphene nano-platelets dispersed in water-ethylene glycol. The graphene nano-suspension was employed as a coolant inside a micro-channel and heat-transfer coefficient (HTC) and pressure drop (PD) values of the system were reported at different operating conditions. The results demonstrated that the use of graphene nano-platelets can potentially augment the thermal conductivity of the working fluid by 32.1% (at wt. % = 0.3 at 60 °C). Likewise, GNP nano-suspension promoted the Brownian motion and thermophoresis effect, such that for the tests conducted within the mass fractions of 0.1%–0.3%, the HTC of the system was improved. However, a trade-off was identified between the PD value and the HTC. By assessing the thermal performance evaluation criteria (TPEC) of the system, it was identified that the thermal performance of the system increased by 21% despite a 12.1% augmentation in the PD value. Furthermore, with an increment in the fluid flow and heat-flux applied to the micro-channel, the HTC was augmented, showing the potential of the nano-suspension to be utilized in high heat-flux thermal applications. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

18 pages, 3833 KiB  
Article
Investigation of Separated Two-Phase Thermosiphon Loop for Relieving the Air-Conditioning Loading in Datacenter
by Hafiz M. Daraghmeh, Mohammed W. Sulaiman, Kai-Shing Yang and Chi-Chuan Wang
Energies 2019, 12(1), 105; https://doi.org/10.3390/en12010105 - 29 Dec 2018
Cited by 15 | Viewed by 3815
Abstract
This study investigates the feasibility of using R-134a filled separated two-phase thermosiphon loop (STPTL) as a free cooling technique in datacenters. Two data center racks one of them is attached with fin and tube thermosiphon were cooled by CRAC unit (computer room air [...] Read more.
This study investigates the feasibility of using R-134a filled separated two-phase thermosiphon loop (STPTL) as a free cooling technique in datacenters. Two data center racks one of them is attached with fin and tube thermosiphon were cooled by CRAC unit (computer room air conditioning unit) individually. Thermosiphon can help to partially eliminate the compressor loading of the CRAC; thus, energy saving potential of thermosiphon loop was investigated. The condenser is a water-cooled design and perfluoroalkoxy pipes were used as adiabatic riser/downcomer for easier installation and mobile capability. Tests were conducted with filling ratio ranging from 0 to 90%. The test results indicate that the energy saving increases with the rise of filling ratio and an optimum energy savings of 38.7% can be achieved at filling ratios of 70%, a further increase of filling ratio leads to a reduction in energy saving. At a low filling ratio like 10%, the evaporator starves for refrigerant and a very uneven air temperature distribution occurring at the exit of data rack. The uneven temperature distribution is relieved considerably when the evaporator is fully flooded. It is also found that the energy saving is in line with the rise of system pressure. Overfilling of the evaporator may lead to a decline of system pressure. A lower thermal resistance occurs at high filling ratios and higher ambient temperature. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

Other

Jump to: Research

11 pages, 1534 KiB  
Case Report
A Comparative Study of the Oil-Free Centrifugal Water Chillers with the Flooded or Falling Film Evaporator—A Case Study
by Kuo-Shu Hung, Jenn-Chyi Chung, Chung-Che Liu, Jun-Jie Lin and Chi-Chuan Wang
Energies 2019, 12(13), 2548; https://doi.org/10.3390/en12132548 - 02 Jul 2019
Viewed by 4038
Abstract
A comparative study regarding the performance of real-scale oil-free centrifugal chillers having the flooded evaporator or falling film evaporator was conducted in this study. The nominal capacity for the test chillers was around 200~230 USRT (US refrigeration ton) (703~809 kW). The compressors of [...] Read more.
A comparative study regarding the performance of real-scale oil-free centrifugal chillers having the flooded evaporator or falling film evaporator was conducted in this study. The nominal capacity for the test chillers was around 200~230 USRT (US refrigeration ton) (703~809 kW). The compressors of the two chillers were identical and R-134a was used as the working fluid. Both evaporators employed the same enhanced tubes (GEWA-B) to fulfill phase change. Tests were conducted in full, 75%, 50%, and 25% loading. Test results indicate that both chillers contained a comparable system performance with an integrated part-load value of around 8.62~8.63. The overall heat transfer coefficient for the flooded evaporator was appreciably higher (20~40%) than the falling film evaporator. This is because the falling film flowrate was below the threshold value and the heat transfer was dominated by evaporation mode. Yet, the heat transfer performance for the falling film evaporator was further jeopardized due to starvation of the film flowrate (partial dry-out), especially in the middle or bottom of the tube bundle. This phenomenon became even more pronounced at partial loading (25%), whereas the flooded evaporator did not reveal such a performance dip at partial loading. Full article
(This article belongs to the Special Issue Experimental Heat Transfer in Energy Systems)
►▼ Show Figures

Figure 1

Show export options expand_more Show export options expand_less
Select all
Export citation of selected articles as:
 
Displaying articles 1-18
Back to TopTop