Research

Jump to: Review

18 pages, 5705 KiB

Open AccessArticle

Dynamic Analysis and Piezoelectric Energy Harvesting from a Nonideal Portal Frame System including Nonlinear Energy Sink Effect

by Angelo M. Tusset, Dim B. Pires, Jose M. Balthazar, Maria E. K. Fuziki, Dana I. Andrade and Giane G. Lenzi

Actuators 2023, 12(7), 298; https://doi.org/10.3390/act12070298 - 22 Jul 2023

Viewed by 1298

Abstract

This paper investigates, through numerical simulations, the application of piezoelectric materials in energy generation. The mathematical model describes a U-shaped portal frame system, excited by an engine with unbalanced mass and coupled to a nonlinear energy sink (NES), which is used as a [...] Read more.

This paper investigates, through numerical simulations, the application of piezoelectric materials in energy generation. The mathematical model describes a U-shaped portal frame system, excited by an engine with unbalanced mass and coupled to a nonlinear energy sink (NES), which is used as a passive vibration absorber. The influence of the piezoelectric material parameters used in the energy collection and the dimensioning parameters of the NES system is deeply analyzed in this paper. Numerical simulations are presented considering all combinations of the parameters of the piezoelectric material model and the NES. The system dynamics were analyzed through phase diagrams and the 0–1 test. The estimation of energy collection was carried out by calculating the average power. The numerical results show that a more significant potential for energy generation is obtained for certain combinations of parameters, as well as chaotic behavior in some cases. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

23 pages, 6709 KiB

Open AccessArticle

Non-Crack-Growth Acoustic Emission Observed in Controlled-Stress-Intensity-Factor High-Cycle-Fatigue Tests

by Roshan Joseph and Victor Giurgiutiu

Actuators 2023, 12(3), 93; https://doi.org/10.3390/act12030093 - 21 Feb 2023

Cited by 2 | Viewed by 1160

Abstract

Acoustic emission (AE) was monitored during stress intensity factor (SIF)-controlled high-cycle fatigue (HCF) tests on an aluminum 2024-T3 specimen with a fatigue crack growing at its center. The SIF control was implemented in such a manner that crack growth could be slowed down [...] Read more.

Acoustic emission (AE) was monitored during stress intensity factor (SIF)-controlled high-cycle fatigue (HCF) tests on an aluminum 2024-T3 specimen with a fatigue crack growing at its center. The SIF control was implemented in such a manner that crack growth could be slowed down and even inhibited while the fatigue experiment continued. In the beginning, a specific type of AE signal was observed while the crack was allowed to grow to up to approximately 9.4 mm in length. Subsequently, the load was reduced in order to control the SIF value at the crack tip and to inhibit the crack growth. AE signals were recorded even when the crack stopped growing, although the specific signature of these AE signals was different from those observed when the crack was growing, as discussed in the text. The gist of the phenomenon reported in this article is that strong AE signals could still be observed even when the crack stopped growing. These latter AE signals could be due to rubbing and clapping of the crack faying surfaces. Travel analysis was consistently performed to ensure that these AE signals were originating from the crack, though not necessarily from the crack tip. In addition, absorbing clay wave dams were built around the crack region to inhibit boundary reflections and grip noise. Fast Fourier Transform (FFT) and Choi–Williams Transform (CWT) analysis were performed to classify the AE signals. It was observed that the AE signals related to crack growth were clearly different from the AE signals originating from the crack while the crack was not growing. Strong S0-mode Lamb wave components were observed in the crack-growth AE signals, whereas strong A0-mode Lamb wave components dominated the non-crack-growth AE signals. Pearson correlation clustering analysis was performed to compare the crack-growth and non-crack growth AE signals. We propose that the fatigue-crack faying surfaces may undergo rubbing and/or clapping during fatigue cyclic loading and thus produce strong AE signals that are registered by the AE system as hits, although the crack is not actually growing. The understanding of this phenomenon is very important for the design of the structural health monitoring (SHM) system based on AE-hit signal capture and interpretation. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

18 pages, 6403 KiB

Open AccessArticle

Training, Control and Application of SMA-Based Actuators with Two-Way Shape Memory Effect

by Renhao Liu, Chen Zhang, Hongli Ji, Chao Zhang and Jinhao Qiu

Actuators 2023, 12(1), 25; https://doi.org/10.3390/act12010025 - 05 Jan 2023

Cited by 2 | Viewed by 1957

Abstract

Shape memory alloys (SMAs) are widely used in aerospace, automobile, and other fields because of their excellent properties, such as large driving force and large deformation. A training method with a bidirectional memory effect is proposed for SMA actuators. The trained SMA units [...] Read more.

Shape memory alloys (SMAs) are widely used in aerospace, automobile, and other fields because of their excellent properties, such as large driving force and large deformation. A training method with a bidirectional memory effect is proposed for SMA actuators. The trained SMA units can be heated and cooled to change their shape (shorten and extend). The trained SMA is used as an actuator to drive the deformation of a structure. Due to the obvious hysteresis characteristics of SMA, a temperature-displacement hysteresis model based on the Preisach model is proposed in order to reduce the influence of hysteresis in the process of structural deformation. The F function method (FFM) is used for Preisach numerical implementation, and a PID control method is used for the precise control of structural deformation. Compared with the PID control method without hysteresis model, this method is superior to the PID control method in response speed and control accuracy. The maximum relative error of three target points in the experiment is 5.45%, which is better than the PID control method without this model. The hysteresis model can be applied to the displacement control of a SMA-based actuator. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

13 pages, 4029 KiB

Open AccessArticle

Effect of Mn Doping on the Microstructure and Electrical Properties of Potassium Niobate Ceramics Using Plasma Spraying

by Rui Gao, Weiling Guo, Hongxing Wang, Xuewu Li and Zhiguo Xing

Actuators 2022, 11(12), 343; https://doi.org/10.3390/act11120343 - 23 Nov 2022

Cited by 2 | Viewed by 1357

Abstract

KNN piezoelectric ceramics are of great importance in the field of scientific research due to their high Curie temperature, good electrical properties, etc. The application of potassium sodium niobate K_0.5Na_0.5NbO₃ (KNN) is strictly limited due to the volatility [...] Read more.

KNN piezoelectric ceramics are of great importance in the field of scientific research due to their high Curie temperature, good electrical properties, etc. The application of potassium sodium niobate K_0.5Na_0.5NbO₃ (KNN) is strictly limited due to the volatility of Na⁺ and K⁺ in KNN and its leakage current. In order to investigate the effect of Mn doping on KNN-based piezoelectric ceramic coatings, KNN and KNN-0.02Mn (KNMN) coatings were successfully prepared using a plasma spraying technique. The phase structure, microscopic morphology, and electrical properties of the coatings were studied in the research. The results showed that both the KNN and KNMN coatings had chalcogenide structures. The KNN coating had an orthogonal phase structure, whereas the KNMN coating had a tetragonal phase structure. Compared with the KNN coating, the microhardness of the KNMN coating was improved through doping with Mn ions. The doping of Mn ions could replace both the A and B sites in the KNN piezoelectric ceramics, further reducing the oxygen vacancies and leakage currents in the coating, and its dielectric properties were improved. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

13 pages, 3514 KiB

Open AccessArticle

Fabrication and Actuation Performance of Selective Laser Melting Additive-Manufactured Active Shape-Memory Alloy Honeycomb Arrays

by Yuesheng Xu, Lei Qiu and Shenfang Yuan

Actuators 2022, 11(9), 242; https://doi.org/10.3390/act11090242 - 24 Aug 2022

Cited by 1 | Viewed by 1634

Abstract

Shape-memory alloy (SMA) honeycomb arrays have drawn worldwide attention for their potential active applications in smart morphing wings. However, the manufacturing of complex active SMA honeycomb arrays via conventional processes is a difficult task, and the actuation performance of the honeycomb arrays has [...] Read more.

Shape-memory alloy (SMA) honeycomb arrays have drawn worldwide attention for their potential active applications in smart morphing wings. However, the manufacturing of complex active SMA honeycomb arrays via conventional processes is a difficult task, and the actuation performance of the honeycomb arrays has not yet been well–investigated. In this work, the active SMA honeycomb arrays were fabricated by selective laser melting (SLM) additive manufacturing, and their actuation performance was investigated. The results show that the SLM–fabricated active SMA honeycomb arrays can generate obvious actuation performance during the transformation and exhibit a higher maximum actuation stress of 2.53 MPa at a R/t ratio of 4 and a tensile pre–strain of 35%. This research will contribute to the design and further improvement of active SMA honeycomb arrays based on SLM additive manufacturing, promoting the engineering applications for smart morphing wings. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

27 pages, 11655 KiB

Open AccessArticle

An SSHC Interface Circuit for Energy Harvesting of Piezoelectric Flags

by Yuansheng Chen, Lichen Tong, Jianzhou Du, Hongli Ji and Pengcheng Zhao

Actuators 2022, 11(7), 175; https://doi.org/10.3390/act11070175 - 22 Jun 2022

Cited by 2 | Viewed by 1574

Abstract

Piezoelectric flags have functions of both classic flags and energy harvesting, and are becoming a new research focus. Interface circuits that convert wind energy to electrical energy are the key component of piezoelectric flags. A new structure for piezoelectric flags was designed to [...] Read more.

Piezoelectric flags have functions of both classic flags and energy harvesting, and are becoming a new research focus. Interface circuits that convert wind energy to electrical energy are the key component of piezoelectric flags. A new structure for piezoelectric flags was designed to generate vibration by wind induction. After theoretical analysis, only SEH (standard energy harvesting) and SSHC (synchronized switch-harvesting-on capacitors) interface circuits were found suitable for piezoelectric flags. Simulation in Multisim was performed to compare SEH and SSHC in different load resistance. Experiments were carried out using different wind speeds. The on-time and delay-time of each switch were controlled by the proposed control algorithm. Both simulation and experimental results indicate that the output voltage with SSHC is higher than the output voltage with SEH. When the resistance is 1700 kΩ and the wind speed is 24 m/s, the output power of SSHC can be increased by 45.63% compared with the SEH circuit. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

14 pages, 2272 KiB

Open AccessArticle

Electrical Properties of Li⁺-Doped Potassium Sodium Niobate Coating Prepared by Supersonic Plasma Spraying

by Yaya Song, Yanfei Huang, Weiling Guo, Xinyuan Zhou, Zhiguo Xing, Dongyu He and Zhenlin Lv

Actuators 2022, 11(2), 39; https://doi.org/10.3390/act11020039 - 26 Jan 2022

Cited by 6 | Viewed by 2665

Abstract

The current work aims to compare the effects of systematic A-site substitutions on the electrical properties of potassium sodium niobate (KNN)-based coating. The A-site elements were replaced by Li⁺ to form (K_0.4675Na_0.4675Li_0.065) NbO₃ (KNLN). The [...] Read more.

The current work aims to compare the effects of systematic A-site substitutions on the electrical properties of potassium sodium niobate (KNN)-based coating. The A-site elements were replaced by Li⁺ to form (K_0.4675Na_0.4675Li_0.065) NbO₃ (KNLN). The pure KNN coating and the Li⁺-doped potassium sodium niobate (KNLN) coating with dense morphology and single perovskite structure were successfully prepared by supersonic plasma spraying, and the phase composition, microscopic morphology and electrical properties of the two coatings were compared and analyzed in detail by XRD, XPS, three-dimensional morphology and SEM on an Agilent 4294A (Santa Clara, CA, USA) and FE-5000 wide-range ferroelectric performance tester. The results show that: as the polarization voltage increases, the pure KNN coating is flatter and fuller, but the leakage current is large. The KNLN coating has a relatively long hysteresis loop and is easily polarized. The domain deflection responds faster to the external electric field, and the resistance of the domain wall motion to the external electric field is small. The dielectric constant of KNLN coating is 375, which is much higher than that of the pure KNN coating with 125, and the dielectric loss is stable at 0.01, which is lower than that of pure KNN coating at 0.1–0.35. This is because Li⁺ doping has successfully constructed a polycrystalline phase boundary in which O-T phases coexist, and has higher dielectric properties, piezoelectric properties and ferroelectric properties. At the same time, due to the high-temperature acceleration process in supersonic plasma spraying, the violent volatilization of the alkaline elements Li⁺, Na⁺ and K⁺ leads to the presence of oxygen vacancies and part of Nb⁴⁺ in the coating, which seriously affects the electrical properties of the coating. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

11 pages, 28380 KiB

Open AccessEditor’s ChoiceArticle

Study on Properties of Potassium Sodium Niobate Coating Prepared by High Efficiency Supersonic Plasma Spraying

by Longlong Zhou, Xuewu Li, Dongyu He, Weiling Guo, Yanfei Huang, Gengchao He, Zhiguo Xing and Haidou Wang

Actuators 2022, 11(2), 28; https://doi.org/10.3390/act11020028 - 18 Jan 2022

Cited by 35 | Viewed by 2856

Abstract

In order to realize the construction of environmentally friendly potassium sodium niobate ceramic coating on metal surface, potassium sodium niobate ceramic coating was prepared by supersonic plasma spraying technology. The morphology, element extension and phase structure of such coating were investigated. The dielectric [...] Read more.

In order to realize the construction of environmentally friendly potassium sodium niobate ceramic coating on metal surface, potassium sodium niobate ceramic coating was prepared by supersonic plasma spraying technology. The morphology, element extension and phase structure of such coating were investigated. The dielectric and ferroelectric properties were also analyzed. The results show that the coating has good quality and tetragonal phase structure. When test frequency ≥ 2 MHz, the dielectric constant is stable at about 300, and also dielectric loss is stable at about 0.05. The coating exhibits good hysteresis loops under different applied electric fields. When the applied electric field is 16 KV/cm, residual polarization value of as-prepared coating reaches 17.02 μC·cm⁻². Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

Review

Jump to: Research

34 pages, 15308 KiB

Open AccessReview

Review on the Nonlinear Modeling of Hysteresis in Piezoelectric Ceramic Actuators

by Yingli Dai, Dequan Li and Dong Wang

Actuators 2023, 12(12), 442; https://doi.org/10.3390/act12120442 - 28 Nov 2023

Viewed by 1570

Abstract

Piezoelectric ceramic actuators have the advantages of fast response speed and high positioning accuracy and are widely used in micro-machinery, aerospace, precision machining machinery, and other precision positioning fields. However, hysteretic nonlinearity has a great influence on the positioning accuracy of piezoelectric ceramic [...] Read more.

Piezoelectric ceramic actuators have the advantages of fast response speed and high positioning accuracy and are widely used in micro-machinery, aerospace, precision machining machinery, and other precision positioning fields. However, hysteretic nonlinearity has a great influence on the positioning accuracy of piezoelectric ceramic actuators, so it is necessary to establish a hysteretic model to solve this problem. In this paper, the principles of the Preisach model, the Prandtl Ishilinskii (PI) model, the Maxwell model, the Duhem model, the Bouc–Wen model, and the Hammerstein model and their application and development in piezoelectric hysteresis modeling are described in detail. At the same time, the classical model, the asymmetric model and the rate-dependent model of these models are described in detail, and the application of the inverse model corresponding to these models in the feedforward compensation is explained in detail. At the end of the paper, the methods of inverse model acquisition and control frequency of these models are compared. In addition, the future research trend of the hysteresis model is also prospected. The ideas and suggestions highlighted in this paper will guide the development of piezoelectric hysteresis models. Full article

(This article belongs to the Special Issue Shape Memory Alloys and Piezoelectric Materials and Their Applications)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Shape Memory Alloys and Piezoelectric Materials and Their Applications

Share This Special Issue

Special Issue Editor

Special Issue Information

Published Papers (9 papers)

Research

Review

Further Information

Guidelines

MDPI Initiatives

Follow MDPI