A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids

Alcalde, Ermitas; Dinarès, Immaculada; Ibáñez, Anna; Mesquida, Neus

doi:10.3390/molecules17044007

Open AccessArticle

A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids

by

Ermitas Alcalde

^*,

Immaculada Dinarès

^*,

Anna Ibáñez

and

Neus Mesquida

Laboratory of Organic Chemistry, Faculty of Pharmacy, University of Barcelona, Joan XXIII s/n, 08028 Barcelona, Spain

^*

Authors to whom correspondence should be addressed.

Molecules 2012, 17(4), 4007-4027; https://doi.org/10.3390/molecules17044007

Submission received: 29 February 2012 / Revised: 20 March 2012 / Accepted: 23 March 2012 / Published: 2 April 2012

(This article belongs to the Collection Ionic Liquids)

Download

Browse Figures

Versions Notes

Abstract

:

A broad and simple method permitted halide ions in quaternary heteroaromatic and ammonium salts to be exchanged for a variety of anions using an anion exchange resin (A⁻ form) in non-aqueous media. The anion loading of the AER (OH⁻ form) was examined using two different anion sources, acids or ammonium salts, and changing the polarity of the solvents. The AER (A⁻ form) method in organic solvents was then applied to several quaternary heteroaromatic salts and ILs, and the anion exchange proceeded in excellent to quantitative yields, concomitantly removing halide impurities. Relying on the hydrophobicity of the targeted ion pair for the counteranion swap, organic solvents with variable polarity were used, such as CH₃OH, CH₃CN and the dipolar nonhydroxylic solvent mixture CH₃CN:CH₂Cl₂ (3:7) and the anion exchange was equally successful with both lipophilic cations and anions.

Keywords:

imidazolium salts; pyridinium salts; ammonium salts; anion exchange resin; counteranion exchange; ionic liquids

Graphical Abstract

1. Introduction

Besides their recognized value as an alternative to conventional solvents, ionic liquids (ILs) are becoming increasingly useful in a widening range of fields in chemistry leaning toward biology. Indeed, ILs have featured extensively in recent scientific open literature and patents, which reflects their importance in research and development (R&D) [1,2,3,4,5,6,7,8,9]. The greenness of commonly used IL syntheses and purification procedures has been analyzed and evaluated [10] as well as their environmental acceptability and their role in sustainable development [11]. Simple imidazolium quaternary salts with a low melting point are a long-standing IL family and at the same time imidazolium-based systems have continued their progress in anion recognition chemistry and N-heterocyclic carbenes (NHCs) [12].

Chemical aspects of imidazolium-based ILs dealing with their preparation, counteranion exchange and purity have been the subject of numerous studies and are currently being investigated with the aim of obtaining pure IL salts, especially halide-free ion pair compounds [4,10,12,13,14,15,16]. A widespread synthesis of imidazolium ILs makes use of a subclass of the Menschutkin reaction, a nucleophilic substitution carried out under neutral conditions between N-substituted imidazoles and an alkyl or benzylhalides, affording the targeted imidazolium system in which the counteranion, that is, the halide ion, can be exchanged by different methods. The most frequent method is the classical halide ion exchange with an inorganic salt (MA) that is also used to remove halide ions in ILs. The halide-containing byproduct salts can then be removed by extraction or precipitation followed by filtration. The challenging issue of purification can be addressed by several IL clean-up protocols to eliminate the unwanted halide and/or metal species, among other byproducts [13,14,15,16]. The isolation and purification of pure heteroaromatic quaternary systems can be troublesome, especially if the different ionic species present in the solution-phase have a similar solubility. In this context, a comparative study of the transformation of N-azolylpyridinium salts to the corresponding pyridinium azolate betaines showed that the method of choice makes use of a strongly basic anion exchange resin, AER (OH⁻ form) [17]. From 1986 onwards, the AER (OH⁻ form) method has been applied to a variety of N-azolylimidazolium and N-azolylpyridinium salts with several interanular linkers. Exploiting our standard AER (OH⁻ form) method, the halide-to-anion exchange of different types of bis(imidazolium) cyclophanes, protophanes and calix [4] arenes was carried out using a column chromatography packed with a strongly basic AER (OH⁻ form) followed by immediate collection of the eluates in diluted aqueous acid solution [12,18,19,20,21,22].

The few examples of anion exchange resin application to ILs reported in the open literature use: (a) the AER (OH⁻ form) method, involving the swap of halides for OH⁻, and then to the [IL][OH] aqueous or hydroalcoholic solution was slowly added a slight excess of an aqueous acid solution and displacement of the OH⁻ anion by the selected A⁻ anion; or (b) the AER (A⁻ form) method, involving the incorporation of the anion in the resin (OH⁻ form) before the anion is exchanged in ILs. Taking advantage of the AER (OH⁻ form) method, Ohno and co-workers prepared Bio-ILs using strong basic Amberlite (OH⁻ form) to exchange a halide ion for OH⁻, and organic acids or natural aminoacids were added to the aqueous solution of [IL][OH] to prepare examples of imidazolium-based [IL][A] [23,24]. Choline cations were similarly transformed to the corresponding ionic liquids [25]. In the same way, several ionic liquid buffers were prepared by treatment of the aqueous solution of [IL][OH] with organic acids [26]. There are only a few reports exploiting the AER (A⁻ form) method in water or aqueous methanol. Thus, several examples of non-aqueous ionic liquids (NAILs) have been prepared using an AER (PO₄³⁻ form) [27]. An AER (OH⁻ form) was loaded with mesylate or tosylate anions by treatment with the corresponding sulfonic acid and the prepared AER (R/Ar-SO₃⁻ form) was then used to transform several N,N’-dialkylpyrrolidinium iodides to the corresponding sulfonate cations [28]. Loading the anion exchanger with camphorsulfonate anion, AER (CS⁻ form) gave the corresponding [IL][CS]from either [IL][OTs] [29] or [IL]Br [30], the latter following a worthless protocol. Treatment of [bmim]Cl with the AER (A⁻ form) -acetate, lactate and nitrate- produced the anion exchange giving [bmim][A] [31]. Recently, we examined the preparation of an AER (A⁻ form) conveniently loaded with a selected anion by treatment with either acids or ammonium salts in water or hydroalcoholic media. The anion exchange was carried out in methanol, providing a pure ionic liquid in quantitative yield. This simple procedure not only offers a convenient way to replace halide anions by a broad range of anions in ILs, including task-specific and chiral ILs, but also eliminates halide impurities [32]. Further studies have been directed towards expanding the scope of the halide-for-anion swap in non-aqueous media to representative imidazolium ILs and known examples of bis(imidazolium)-based frameworks for anion recognition. Both lipophylic imidazolium systems and low hydrophilic anions proceeded in excellent to quantitative yields [33].

In this paper we report how the AER (A⁻ form) method can be exploited for a halide-to-anion exchange in several illustrative examples from IL families. The anion source and solvent selection for loading the AER (OH⁻ form) were first examined using different acids or ammonium salts and organic solvent mixtures with variable polarity. The halide-to-anion exchange was then studied using imidazolium-based ILs, random examples of quaternary azolium and pyridinium salts as well as quaternary ammonium salts from the APIs family (Figure 1).

Figure 1. The AER (A⁻ form) method applied to representative quaternary heteroaromatic salts and quaternary ammonium salts.

2. Results and Discussion

2.1. AER (A⁻ Form) Method. Anion Loading

Anion source. Two methods were used to load the anions: Via A, from acids, or via B, involving the corresponding ammonium salt (Scheme 1 and Table 1).

The AER (OH⁻ form) was packed in a column and treated with an aqueous or hydromethanolic solution of the acid or ammonium salt. The loading effectiveness was then checked by passing a methanolic solution of [bmim]I through the AER column loaded with the target anion and the halide ion to another anion exchange proceeded in quantitative yield.

Scheme 1. AER (A⁻ form) method: The loading.

Table 1. Loading AER (OH⁻ form): Anion source and solvents.

**Table 1.** Loading AER (OH⁻ form): Anion source and solvents.
Anion	Source	Solvent	Anion	Source	Solvent
AcO⁻	NH₄⁺AcO⁻	(a)	AcO⁻	AcOH	(b)
Cl⁻	NH₄⁺Cl⁻	(a)	Cl⁻	HCl	(a), (b)
PF₆⁻	NH₄⁺PF₆⁻	(a)	PF₆⁻	HPF₆	(b)
BF₄⁻	NH₄⁺BF₄⁻	(a)	BF₄⁻	HBF₄	(b)
CF₃SO₃⁻	NH₄⁺CF₃SO₃⁻	(a)	BzO⁻	BzOH	(b)−(g)
SCN⁻	NH₄⁺ SCN⁻	(a)	(S)-Lactate⁻	(S)-Lactic acid	(b)
F¯	NH₄⁺F⁻	(a)	MeSO₃⁻	MeSO₃H	(b)
H₂PO₄⁻	NH₄⁺H₂PO₄⁻	(a)	Bu₂PO₄⁻	Bu₂PO₄H	(b), (c)
HSO₄⁻	NH₄⁺HSO₄⁻	(a)	ClO₄⁻	HClO₄	(a), (b)
Ph₄B⁻	NH₄⁺Ph₄B⁻	(d), (e)	NO₃⁻	HNO₃	(a), (b)
			Ibu⁻	Ibuprofene	(d), (e)

Solvent: (a) H₂O; (b) CH₃OH:H₂O; (c) CH₃OH; (d) CH₃CN:H₂O (9:1); (e) CH₃CN:CH₃OH (9.5:0.5); (f) THF:H₂O (1:1); (g) THF:CH₃OH (4:1).

Thus, following via A, the resin was charged with organic oxoanions derived from carboxilate (R-CO₂⁻), including chiral (S)-lactate, sulfonate (MeSO₃⁻) or phosphate (Bu₂PO₄⁻), together with inorganic anions such as Cl⁻, NO₃⁻ or ClO₄⁻, by treatment with the corresponding 1% aqueous acidic solutions. When the loading was performed with the aqueous solution of CF₃SO₃H, HF, H₃PO₄ or H₂SO₄, the polymeric matrix was partially denaturalized by overheating. For this reason, anions such as CF₃SO₃⁻, F⁻, H₂PO₄⁻ or HSO₄⁻ were loaded in the resin using aqueous solutions of their ammonium salts (via B). In order to confirm the efficiency of the method, both procedures were used to load AcO⁻, Cl⁻, PF₆⁻ or BF₄⁻ anions, and identical results were obtained. A few attempts to load anions from their corresponding Na⁺, K⁺ or Li⁺ salt showed, however, that the replacement of OH⁻ in the AER was incomplete, as evidenced by an observed mixture of anions in the checking, and this was not further studied.

Solvent selection. We extended our studies to the loading of hydrophobic anions, and explored alternative solvents and solvent mixtures. Benzoic acid was selected to prepare the AER (BzO⁻ from) and then a methanolic solution of [bmim]I was used to check the iodide-to-benzoate anion switch. The resin was first packed in a column and generously washed with the solvent, which was used afterwards to load the benzoate anion. Pure solvents such as distilled CH₃OH, CH₃CN, THF and CH₂Cl₂ were assayed, but only CH₃OH provided the optimal loading. Then, several solvent mixtures containing CH₃CN or THF with H₂O or CH₃OH were applied. Among the successful loading solvent mixtures that provided the AER in the BzO⁻ form, those with the lowest proportions of water or methanol were CH₃CN:H₂O (9:1), CH₃CN:CH₃OH (9.5:0.5), THF:H₂O (1:1) or THF:CH₃OH (4:1) (Scheme 1 and Table 1).

These results indicated that a non-aqueous mixture can be used to incorporate lipophylic anions, although the presence of a protic solvent was necessary for the OH⁻ replacement in the AER. Once the suitable solvent conditions were found, acetonitrile solvent mixtures were used to load representative hydrophobic anions: The anti-inflammatory acid ibuprofen to explore via A and ammonium tetraphenylborate to explore via B.

In order to check the loading effectiveness, a methanolic solution of [bmim]I was passed through the AER (Ibu⁻ form) or AER (Ph₄B⁻ form) and the pure [bmim][Ibu] [34] or [bmim][Ph₄B] [35] was obtained (see later). These results confirmed that lipophylic anions replace the OH⁻ anion in resin when using the appropriate solvent and the corresponding AER (A¯ form) obtained can then be used for the halide-to-anion switch.

Loading and exchange ability. The anion amount that the AER can load and the amount of halide that can then be exchanged were examined. Thus, 2.5 g (~3 cm³) of commercial wet A-26 (OH form) was treated with a 1% NH₄AcO aqueous solution until the pH value of the eluates indicated that loading was complete. Thus, 14.54 mmol of AcO⁻ was loaded with a maximum loading of 5.8 mmol of AcO⁻ per 1 g of this AER. In this context, the synthesis and characterization of resin-supported organotrifluoroborates have recently been reported and the loading was quantified by a UV/Vis spectroscopic analysis [36].

A 50 mM methanolic solution of [bbim]Br was passed through the packed column and aliquots were collected periodically and examined by ¹H-NMR. The related integration of signals corresponding to the anion and imidazolium cation indicated that the exchange process was quantitative up to nearly 14.54 mmol of ionic liquid, suggesting that the Br⁻ exchange could take place as long as there was enough AcO⁻ anion (Scheme 2).

Scheme 2. AER (A⁻ form) method. (i) Maximum anion loading. (ii) Checking anion exchange capacity.

Additionally, it should also be considered that the AER used in the exchange can be recycled by treatment with 10% NaOH aqueous solution, and the recovered AER (OH⁻ form) can be re-utilized for a new anion loading. In the present study, the chosen resin was Amberlyst A-26, given that it allows the use of aqueous mixtures and non-aqueous solvents, but other similar strongly basic anion exchange resins can be used instead.

2.2. AER (A⁻ Form) Method. Anion Exchange

Having achieved the loading of several anions in the AER, we examined their efficiency in the counterion exchange in imidazolium-based ILs, including [bmim]I or Br, [bbim]I or Br or [mmim]I as well as [bm₂im]Br. Thus, a methanolic solution of IL was passed through a column packed with the AER (A⁻ form) previously prepared, and the solvent was removed from the collected eluates. Following this simple method, in almost all cases I⁻ or Br⁻≥ 95% halide-for-anion swapping was obtained except for the hydrophobic anions Ph₄B⁻ and Ibu⁻, which gave for example, from [bmim]I in 65% and 95% yield, respectively (Table 2 and Scheme 3).

Table 2. Results of the iodide or bromide exchange in imidazolium ionic liquids.

**Table 2.** Results of the iodide or bromide exchange in imidazolium ionic liquids.
		[bmim]I or Br		[bbim]I or Br		[mmim]I		[bm₂im]Br
Anion	Solvent	Yield (%) ^a	I⁻ (ppm) ^b	Yield (%) ^a	I⁻ (ppm) ^b	Yield (%) ^a	I⁻ (ppm) ^b	Yield (%) ^a	Br⁻ (ppm) ^b
AcO⁻	CH₃OH	100	<20	100	<20	100	<20	98	<13
BzO⁻	CH₃OH	100	<20	100	<20	95	<20	100	<13
(S)-Lactate⁻	CH₃OH	100	20–40	100	<20	100	<20	100	<13
MeSO₃⁻	CH₃OH	100	<20	100	<20	95	<20	92	<13
MeSO₃⁻	CH₃CN	―		―		―		100	<13
Bu₂PO₄⁻	CH₃OH	100	<20	100	<20	100	<20	100	<13
F⁻	CH₃OH	82	ND ^c	100	ND ^c	―		―
Cl⁻	CH₃OH	100	ND	100	ND	100	ND	―
PF₆⁻	CH₃OH	100	20–40	100	<20	100	<20	91	ND
PF₆⁻	CH₃CN	―		―		―		100	13–26
NO₃⁻	CH₃OH	100	<20	100	<20	100	20–40	―
ClO₄⁻	CH₃OH	100	100–120	100	20–40	100	20–40	―
BF₄⁻	CH₃OH	100	<20	100	<20	100	20–40	97	13–26
H₂PO₄⁻	CH₃OH	100	<20	100	20–40	100	<20	―
HSO₄⁻	CH₃OH	100	<20	100	20–40	100	<20	―
CF₃SO₃⁻	CH₃OH	100	<20	100	<20	100	<20	100	<13
SCN⁻	CH₃OH	100	ND	100	ND	100	ND	100	ND
Ph₄B⁻	CH₃OH	65	<20	45	<20	―		―
Ph₄B⁻	CH₃CN	95	<20	100	<20	―		91	<13
Ibu⁻	CH₃OH	95	<20	―		―		―
Ibu⁻	CH₃CN	100	<20	―		―		96	<13

ND: Not Determined. ^a Recovered new ion pair. Yields ≥95% in CH₃OH were not further examined in CH₃CN; ^b Halide contents after anion exchange determined by the silver chromate test; ^c Analyzed by HPLC/IC from exchange of Br⁻ by F⁻: Presence of Br⁻ anion was not observed.

Scheme 3. AER (A⁻ form) method applied to imidazolium-based ILs.

Moreover, no evidence of N-heterocyclic carbenes (NHCs) and/or dealkylation by-product formation was observed despite the basic environment, e.g., anion basicity [13,37,38]. The purity of the ionic liquids obtained by this method was qualitatively determined using ¹H-NMR spectra, and/or ESI(−)-MS experiments, and according to the silver chromate test, most analyses indicated low halide contents (<20 ppm for I⁻ or <13 ppm for Br⁻). Further quantification of possible halide impurity was restricted by instrumental limitation [32].

Although the halide exchange occurred with lipophylic anions such as Ph₄B⁻, when the process was carried out in methanol the yield of the recovered compound decreased to 65%, due to the change of solubility of the new ion pair, which caused their partial retention in the resin. Hence, organic solvents such as CH₃CN or CH₂Cl₂ or CH₃CN:CH₂Cl₂ solvent mixtures were then selected to perform the halide switch, the treatment of [bmim]I with AER (BzO⁻ form) being used to check the process. The results indicated that the exchange was successful in both aprotic organic solvents, while the use of pure CH₂Cl₂as a solvent in our usual exchange procedure was discarded due to experimental difficulties, after testing several combinations, the mixture with the highest proportion of dichloromethane that was workable was found to be CH₃CN:CH₂Cl₂ (3:7). This enabled a quantitative iodide-for-benzoate swap and afforded the possibility for those exchanges of hydrophobic ionic species.

Accordingly, the preparation of [bmim][Ph₄B] or [bbim][Ph₄B] from their corresponding iodide salts using the AER (Ph₄B^¯ form) in CH₃OH provided the corresponding ion pair in 65% and 45% yield, respectively. The yield increased to 95% and 100% when CH₃CN was used, confirming that less polar solvents in the exchange process substantially improved the recovery of the less hydrophilic ion pair (Scheme 4). Similarly, [bm₂im]Br was directly studied in CH₃CN and the exchange of Ph₄B⁻ and Ibu⁻ anions proceeded in 91% and 96% yields, respectively (Table 2).

Hydrophobic salts such as hexylmethylimidazolium chloride [hmim]Cl or decylmethylimidazolium chloride [dmim]Cl were used to swap the chloride for the ibuprofenate anion. A solution of the corresponding ionic liquid in CH₃CN was passed through the AER (Ibu⁻ form) affording the anion exchange in ≤95% yields. A more lipophylic solvent was then used and quantitative results were obtained with the dipolar nonhydroxylic organic solvent mixture CH₃CN:CH₂Cl₂ (3:7) (Scheme 4 and Table 3).

Scheme 4. AER (A⁻ form) method. Halide to lipophylic anion exchange.

Table 3. Comparative results of chloride exchange in [hmim]Cl and [dmim]Cl.

**Table 3.** Comparative results of chloride exchange in **[hmim]Cl** and **[dmim]Cl**.
Cation	Anion	Solvent	Yield (%) ^a	Cl⁻ (ppm) ^b
hmim	Ibu⁻	CH₃CN	90	<6
	Ibu⁻	CH₃CN:CH₂Cl₂ (3:7)	100	<6
dmim	Ibu⁻	CH₃CN	87	<6
	Ibu⁻	CH₃CN:CH₂Cl₂ (3:7)	100	<6

^a Yield of the recovered new ion pair; ^b Halide contents after anion exchange determined by silver chromate test.

Next, the AER (A⁻ form) method was extended to other anions. Thus, a methanolic solution of [bmim]Cl was passed through the AER (PF₆⁻ form) packed column and the eluates were analyzed after the solvent was removed. The ¹H-NMR spectrum coincided with that of [bmim][PF₆], which indicated a successful exchange confirmed by the silver chromate test (<6 ppm of Cl⁻). Similarly, a methanolic solution of [bmim][PF₆] was passed through the AER (Cl⁻ form) packed column and the ¹H-NMR spectrum also showed the quantitative exchange (Scheme 5). Thus, a conveniently loaded AER can be used to carry out the swapping from a range of anions other than halides. The process was followed by ¹H-NMR, since the signal corresponding to the C(2)-H of the imidazolium moiety is generally the most influenced by the nature of the anion (see Experimental section); for example, the chemical shift value measured in CDCl₃ (0.02 M) is 9.07 ppm in [bmim][PF₆] while in the same conditions this value is 10.99 ppm in [bmim]Cl.

Scheme 5. AER (A⁻ form) method: Chloride to hexafluorophosphate exchange and vice versa.

Regarding other heteroaromatic cationic systems, pyridinium ([bmpy]I) or benzimidazolium (2·I) nuclei were chosen as examples to carry out the anion swap, together with the well known NHC precursor 1,3-dimesitylimidazolium salt (1·Cl) (Figure 1 and Scheme 6). A methanolic solution of [bmpy]I was passed through a column packed with the convenient AER (A⁻ form), and the corresponding pure [bmpy][A] were obtained in ≥ 98% yield, except for the acetate anion, which was recovered in 84% yield. Changing to a more hydrophobic solvent, the iodide-for-acetate swap in acetonitrile proceeded in quantitative yield. In the treatment of [bmpy]I with the AER (A⁻ form), there was no evidence in any case of the formation of decomposition byproducts, despite the basicity of some anions, e.g., acetate (Table 4).

Scheme 6. Halide-to-anion exchange in quaternary azolium and pyridinium salts.

Following the same procedure, a methanolic solution of the new benzimidazolium salt 2·I was used to obtain the corresponding ion pair 2·A, with excellent yields. The iodide exchange of the white solid 2·I (m.p. 150–1 °C) led to oily ion pairs at room temperature or solids with a low melting point (see Experimental section). The new benzimidazolium salts 2·A are related to previously reported benzimidazolium salts with potential use as new materials, e.g., ionic liquid crystals [39] and crystalline metal-containing ILs [40,41,42]. Likewise, the chloride anion in 1,3-dimesitylimidazolium salt 1·Cl can be successfully displaced by a wide range of anions using the AER (A⁻ form). When the swapping took place in methanol, the recovery of 1·A was between 80 to 95%, but in acetonitrile yields were nearly quantitative (Table 4). In all cases the silver chromate test revealed the low chloride content after the exchange (<6 ppm), which confirmed the easy swapping of Cl⁻ anion. These examples demonstrated that the method is also effective with non IL cationic systems, and is a general method for preparing tuneable quaternary heteroaromatic salts. Accordingly, the well-known catalyst precursor 1·Cl [43] was easily transformed in 1·A, and the presence of different counteranions could potentially modulate the formation of organometallic complexes due to their improved solubility and the stabilizing effect of anion participation.

Table 4. Results of the halide exchange in pyridinium, benzimidazolium and imidazolium salts [bmpy][I], 1·Cl and 2·I.

**Table 4.** Results of the halide exchange in pyridinium, benzimidazolium and imidazolium salts **[bmpy][I]**, **1·Cl** and **2·I**.
		[bmpy][I]		1·Cl		2·I
Anion	Solvent	Yield (%) ^a	I⁻ (ppm) ^b	Yield (%) ^a	Cl⁻ (ppm) ^b	Yield (%) ^a	I⁻ (ppm) ^b
AcO⁻	CH₃OH	84	<20	95	<6	100	<20
AcO⁻	CH₃CN	100	<20	―		―
BzO⁻	CH₃OH	100	<20	92	<6	95	<20
BzO⁻	CH₃CN	―		100	<6	―
(S)-Lactate⁻	CH₃OH	100	<20	98	<6	100	<20
MeSO₃⁻	CH₃OH	100	<20	91	<6	90	<20
MeSO₃⁻	CH₃CN	―		100	<6	100
Bu₂PO₄⁻	CH₃OH	100	<20	95	<6	97	<20
PF₆⁻	CH₃OH	100	<20	100	<6	100	<20
BF₄⁻	CH₃OH	98	<40	79	<6	100	<20
BF₄⁻	CH₃CN	―		100	<6	―
CF₃SO₃⁻	CH₃OH	100	<20	88	<6	95	<20
CF₃SO₃⁻	CH₃CN	―		95	<6	―
SCN⁻	CH₃OH	100	ND	91	ND	100	ND
SCN⁻	CH₃CN	―		97	ND	―
Ph₄B⁻	CH₃CN	―		82	<6	―

ND: Not Determined. ^a Yield of the recovered new ion pair. Yields ≥95% in CH₃OH were not further examined in CH₃CN; ^b Halide contents after anion exchange determined by silver chromate test.

Two examples of quaternary ammonium salts were selected from the API family to confirm the efficiency of the method with this type of ILs. The choline lactate ([Cho][Lact]) [44] was quantitatively prepared from the corresponding [Cho]I using the AER (Lact⁻ form) in methanol. Didecyldimethylammonium bromide ([d₂m₂N]Br) was transformed to the antibacterial-anti-inflammatory didecyldimethylammonium ibuprofenate [d₂m₂N][Ibu] [45].

This hydrophobic ammonium salt required the lipophylic solvent mixture CH₃CN:CH₂Cl₂ (3:7) to afford the quantitatively iodide-to-ibuprofenate switch, since in acetonitrile the yield was only 61% (Scheme 7 and Table 5).

Scheme 7. AER (A⁻ form) method. Quaternary ammonium salts.

Table 5. The halide exchange in quaternary ammonium salts [Cho]I and [d₂m₂N]Br.

**Table 5.** The halide exchange in quaternary ammonium salts **[Cho]I** and **[d₂m₂N]Br**.
Cation	Anion	Solvent	Yield (%) ^a	I⁻ (ppm) ^b
Cho	(S)-Lactate⁻	CH₃OH	100	<20
d₂m₂N	Ibu⁻	CH₃CN	61	<13
	Ibu⁻	CH₃CN: CH₂Cl₂ (3:7)	100	<13

^a Yield of the recovered new ion pair; ^b Halide contents after anion exchange determined by silver chromate test.

The quaternary heteroaromatic and ammonium ILs prepared taking advantage of the AER (A⁻ form) method in organic solvents were characterized by ¹H-NMR, electrospray ionization mass spectrometry in the negative mode and the halide content was determined by the silver chromate test. When the recovery of the new ion pair [IL][A] was ≤95%, a new assay was performed using a less polar organic solvent, which improved the yield in the range of 95% to 100%. As mentioned above, the use of an anion exchange resin implies the possibility of sorbet contamination [13,46], so, nano-particulates may be an issue to analyze. The analysis of possible nano-particulate contamination was, however, beyond the scope of the present study.

Recapping the results, the AER (A⁻ form) method applied to different examples of quaternary heteroaromatic salts and ionic liquids permitted the halide to be swapped for assorted anions in excellent yields of ≥95% when the appropriate organic solvent or solvent mixture was used. It was confirmed that the AER (A⁻ form) method is efficient with imidazolium-based ILs, improving the currently operative procedures of classical counteranion exchange. Against a large pool of quaternary heteroaromatic and ammonium salts, we limited ourselves to the eleven examples shown in Figure 1 to validate the AER (A⁻ form) method in non-aqueous media.

3. Experimental

3.1. General

Ion exchanger resin Amberlyst A-26 (Aldrich, OH⁻ form), [hmim]Cl, [dmim]Cl, [Cho]I and [d₂m₂N]Br together with all acids, ammonium salts, reagents and solvents were purchased from commercial suppliers, unless mentioned otherwise, and used without further purification. All solvents were reagent grade and methanol and THF were distilled prior to use. [bmim]I [32], [bmim]Br [32], [bbim]I [32], [bbim]Br [32], [mmim]I [32], [bm₂im]Br [47], [bmpy]I [48], and 1·Cl [49] were prepared according with the literature. ¹H-NMR and ¹³C-NMR spectra were recorded on a Varian Gemini 300 (300 MHz for ¹H and 75.4 MHz for ¹³C) spectrometer at 298 K. ¹H and ¹³C chemical shifts were referenced with TMS as an internal reference. Mass spectrometric analyses were performed on a LC/MSD-TOF (2006) mass spectrometer with a pumping system HPLC Agilent 1100 from Agilent Technologies at Serveis Científico-Tècnics of universitat de Barcelona. The pH was measured with benchmeter pH1100 (Eutech Instrunments, Nijkerk, The Netherlands), using Hamilton Flushtrode pH electrode for hydroalcoholic solutions.

3.2. Loading the AER (OH⁻ Form) with Acids or Ammonium Salts

A glass column (1 cm diameter ) packed with 2.5 g (~3 cm³) of commercial wet strongly basic anion exchange Amberlyst A-26 (OH⁻ form) was washed with water, and the column bed was equilibrated progressively with water-solvent mixtures until reaching the selected solvent media used afterwards for anion loading (~25 mL of each solvent mixture). A 1% acid or ammonium salt solution in the appropriate solvent was passed slowly through the resin until the eluates had the same pH value as the original selected acid solution, and then the resin was washed generously with solvent until constant pH. The process was carried out at room temperature, using gravity as the driving force.

3.3. Anion Exchange: General Procedure

A solution of the imidazolium salt (0.5–0.6 mmol) in 10 mL of the selected solvent was passed slowly through a column packed with ~3 cm³ of Amberlyst A-26 (A^– form), and then washed with 25 mL of solvent. The combined eluates were evaporated, and the residue obtained was dried in a vacuum oven at 60 °C with P₂O₅ and KOH pellets.

3.4. Silver Chromate Test

The amount of halide contents was determined by a silver chromate test following a similar protocol to that described by Sheldon and co-workers [31]. An aqueous solution (5 mL) of potassium chromate (5% p/v in Milli-Q water, 0.257 M) was added to the sample (5–10 mg). To 1 mL of the resulting dark yellow solution was added a minimum amount of silver nitrate aqueous solution (0.24% p/v in Milli-Q water, 0.014 M). A persistent red suspension of silver chromate would be observed if the sample was free of halide. The minimum measurable amount of silver nitrate aqueous solution was 0.011 mL; consequently, the detection limit is approx. 6 ppm for Cl⁻, 13 ppm for Br⁻ or 20 ppm for I⁻. The halide content was determined at least twice for each sample.

3.5. 1,3-Dibutyl-5,6-dimethylbenzimidazolium Iodide(2·I)

A suspension of 5,6-dimethyl-1H-benzimidazole (1.00 g, 6.84 mmol) and NaH (0.40 g, 16.66 mmol) in dry THF (100 mL) was stirred under argon atmosphere at 60 °C for 1 h, and then 1-iodobutane (1.50 g, 8.15 mmol) was added. The reaction mixture was stirred at 65 °C for 48 h, and then 5 mL of ethanol were added. The solvent was evaporated to dryness, and the residue was treated with water (50 mL) and extracted with CH₂Cl₂ (3 × 50 mL). The organic solution was dried over anhydrous Na₂SO₄, filtered and the solvent was eliminated under vacuum. A mixture of the previous yellow oil (1.34 g, 6.62 mmol) and 1-iodobutane (1.23 g, 6.70 mmol) was stirred under argon atmosphere at 85 °C for 20 h. The reaction mixture was washed with dry diethyl ether (3 × 25 mL) in an ultrasonic bath, providing the pure 2·I as a white solid (2.47 g, 93% yield). M.p. 150–1 °C. δ_H (300 MHz; CDCl₃; Me₄Si) 0.99 (6H, t, J = 7.4 Hz, N-C₃H₆-CH₃), 1.45 (4H, m, N-C₂H₄-CH₂-CH₃), 2.02 (4H, m, N-CH₂-CH₂-C₂H₅), 2.47 (6H, s, C(5,6)-Me), 4.56 (4H, t, J = 7.4 Hz, N-CH₂-C₃H₇), 7.42 (2H, s, C(4,7)-H) and 11.01 (1H, s, C(2)-H). δ_C (75.4 MHz, CDCl₃) 13.5, 19.8, 20.7, 31.3, 47.3, 112.8, 129.8, 137.5, 140.4. HRMS-ESI(+) Calcd for C₁₇H₂₇N₂ [M]⁺ 259.2169, found 259.2167.

Melting points of compounds 2·A: 2·MeSO₃, 62–3 °C; 2·Bu₂PO₄, 56–7 °C; 2·PF₆, 85–6 °C; 2·BF₄, 109–110 °C; 2·CF₃SO₃, 78–9 °C; 2·SCN, 64–5 °C; 2·AcO, 2·BzO and 2·Lact are oily compounds at room temperature

3.6. 1H-NMR Data of Compounds [bmim][A] (Table 6), [bbim][A] (Table 7), [mmim][A] (Table 8), [hmim][A] (Table 9), [dmim][A] (Table 9), [bm2im][A] (Table 10), [bmpy][A] (Table 11), 1·A (Table 12), 2·A (Table 13), [Cho][A] (Table 14) and [d2m2N][A] (Table 14)

Table 6. ¹H-NMR chemical shift values of 1-butyl-3-methylimidazolium salt [bmim][A] (300 MHz) at 298 K ^a. Molecules 17 04007 i001

**Table 6.** ¹H-NMR chemical shift values of 1-butyl-3-methylimidazolium salt **[bmim][A]** (300 MHz) at 298 K ^a.
Anion	Solvent	H-2	H-4	H-5	Bu	Me	A⁻
AcO⁻	CDCl₃	11.35	7.09	7.08	4.30; 1.86; 1.37; 0.96	4.06	1.99
BzO⁻	CDCl₃	11.00	7.09	7.09	4.29; 1.84; 1.33; 0.92	4.08	8.10; 7.33
( S)-Lactate⁻	CDCl₃	11.19	7.17	7.17	4.31; 1.89; 1.38; 0.98	4.08	3.46; 1.41
MeSO₃⁻	CDCl₃	10.21	7.25	7.20	4.28; 1.87; 1.38; 0.97	4.05	2.80
Bu₂PO₄⁻	CDCl₃	10.19	7.36	7.23	4.25; 1.80; 1.33; 0.88	4.00	3.80;1.54;1.33; 0.88
I⁻ ^b	CDCl₃	10.27	7.52	7.44	4.35; 1.93; 1.41; 0.99	4.14
Br⁻	CDCl₃	10.41	7.46	7.37	4.35; 1.91; 1.40; 0.98	4.13
F⁻	CDCl₃	(c)	7.50	7.33	4.29; 1.87; 1.36; 0.95	4.06
Cl⁻	CDCl₃	10.99	7.31	7.24	4.33; 1.91; 1.40; 0.98	4.13
PF₆⁻	CDCl₃	9.07	7.26	7.23	4.20; 1.88; 1.38; 0.97	3.98
NO₃⁻	CDCl₃	10.02	7.35	7.30	4.25; 1.88; 1.38; 0.97	4.02
ClO₄⁻	CDCl₃	9.15	7.30	7.26	4.23; 1.89; 1.39; 0.98	4.02
BF₄⁻	CDCl₃	8.98	7.28	7.24	4.21; 1.87; 1.39; 0.97	3.98
CF₃SO₃⁻	CDCl₃	9.27	7.32	7.28	4.21; 1.88; 1.38; 0.97	3.99
SCN⁻	CDCl₃	9.59	7.36	7.31	4.32; 1.92; 1.41; 0.99	4.11
Ibu⁻	CDCl₃	9.86	7.10	7.02	4.02; 1.66; 1.24; 0.87	3.71	7.26; 6.95; 3.53; 2.35; 1.75; 1.39; 0.82
AcO⁻	CD₃CN	9.25	7.35	7.32	4.14; 1.80; 1.31; 0.93	3.84	1.66
BzO⁻	CD₃CN	9.43	7.29	7.28	4.19; 1.80; 1.30; 0.92	3.86	7.93; 7.27
MeSO₃⁻	CD₃CN	8.63	7.37	7.34	4.16; 1.80; 1.31; 0.94	3.83	2.43
I⁻	CD₃CN	8.56	7.39	7.35	4.14; 1.81; 1.31; 0.94	3.83
Cl⁻	CD₃CN	9.04	7.39	7.36	4.15; 1.80; 1.31; 0.93	3.84
PF₆⁻	CD₃CN	8.42	7.35	7.31	4.11; 1.79; 1.30; 0.93	3.80
NO₃⁻	CD₃CN	8.58	7.37	7.34	4.13; 1.81; 1.31; 0.94	3.82
ClO₄⁻	CD₃CN	8.43	7.37	7.35	4.12; 1.81; 1.32; 0.94	3.82
BF₄⁻	CD₃CN	8.43	7.36	7.33	4.12; 1.82; 1.32; 0.94	3.81
CF₃SO₃⁻	CD₃CN	8.43	7.36	7.33	4.12; 1.80; 1.32; 0.94	3.81
SCN⁻	CD₃CN	8.49	7.37	7.34	4.13; 1.80; 1.30; 0.94	3.82
Ph₄B⁻	CDCl₃	4.54	6.01	5.84	3.16; 1.33; 1.13; 0.89	2.76	7.52; 6.97; 6.78
Ph₄B⁻	CD₃CN	8.19	7.27 ^d	7.27 ^d	4.05; 1.77; 1.30; 0.93	3.74	7.27; 6.99; 6.84
Ph₄B⁻	DMSO-d₆	9.06	7.74	7.67	4.13; 1.75; 1.24; 0.89	3.82	7.16; 6.91; 6.78

^a Solution concentrations are 0.02 M; ^b Unambiguous assignments were made by NOESY-1D (400 MHz); ^c Signal not observed; ^d Included in the phenyl signal.

Table 7. ¹H-NMR chemical shift values of 1,3-dibutylimidazolium salt [bbim][A] (300 MHz) at 298 K ^a. Molecules 17 04007 i002

**Table 7.** ¹H-NMR chemical shift values of 1,3-dibutylimidazolium salt **[bbim][A]** (300 MHz) at 298 K ^a.
Anion	Solvent	H-2	H-4,5	Bu	A⁻
AcO⁻	CDCl₃	11.32	7.14	4.35; 1.86; 1.39; 0.97	2.01
BzO⁻	CDCl₃	11.40	7.16	4.34; 1.87; 1.35; 0.93	8.10; 7.32
(S)-Lactate⁻	CDCl₃	11.29	7.14	4.33; 1.87; 1.37; 0.96	4.02; 1.39
MeSO₃⁻	CDCl₃	9.73	7.51	4.30; 1.88; 1.37; 0.96	2.75
Bu₂PO₄⁻	CDCl₃	11.05	7.11	4.37; 1.88; 1.40; 0.94	3.87; 1.62; 1.40; 0.94
I⁻	CDCl₃	10.34	7.38	4.38; 1.95; 1.42; 0.99
Br⁻	CDCl₃	10.58	7.42	4.36; 1.90; 1.37; 0.95
F⁻	CDCl₃	(b)	7.17	4.30; 1.89; 1.40; 0.98
Cl⁻	CDCl₃	11.05	7.23	4.38; 1.92; 1.41; 0.98
PF₆⁻	CDCl₃	9.05	7.23	4.24; 1.88; 1.39; 0.98
NO₃⁻	CDCl₃	9.89	7.39	4.25; 1.86; 1.33; 0.94
ClO₄⁻	CDCl₃	9.24	7.38	4.26; 1.88; 1.37. 0.96
BF₄⁻	CDCl₃	9.12	7.36	4.23; 1.87; 1.36; 0.95
H₂PO₄⁻	CDCl₃	10.59	7.31	4.40; 1.84; 1.34; 0.92
HSO₄⁻	CD₃CN	10.84	7.40	4.39; 1.84; 1.34; 0.91
CF₃SO₃⁻	CDCl₃	9.49	7.28	4.26; 1.88; 1.38; 0.98
SCN⁻	CDCl₃	9.18	7.34	4.25; 1.88; 1.38; 0.97
Ph₄B⁻	CDCl₃	(b)	5.81	3.10; 1.30; 1.13; 0.89	7.50; 6.98; 6.82
Ph₄B⁻	DMSO-d₆	9.19	7.79	4.15; 1.77; 1.26; 0.90	7.18; 6.92; 6.78

^a Solution concentrations are 0.02 M. ^b Signal not observed.

Table 8. ¹H-NMR chemical shift values of 1,3-dimethylimidazolium salt [mmim][A] (300 MHz) at 298 K ^a. Molecules 17 04007 i003

**Table 8.** ¹H-NMR chemical shift values of 1,3-dimethylimidazolium salt **[mmim][A]** (300 MHz) at 298 K ^a.
Anion	Solvent	H-2	H-4,5	Me	A⁻
AcO⁻	CD₃CN	9.05	7.32	3.83	1.69
BzO⁻	CD₃CN	9.29	7.33	3.85	7.93; 7.28
(S)-Lactate⁻	CDCl₃	11.04	7.15	4.03	3.80; 1.38
MeSO₃⁻	CD₃CN	8.58	7.33	3.83	2.43
Bu₂PO₄⁻	CDCl₃	10.88	7.15	4.04	3.86; 1.61; 1.39; 0.90
I⁻	CD₃CN	8.48	7.34	3.83
Cl⁻	CD₃CN	8.57	7.34	3.83
PF₆⁻	CD₃CN	8.38	7.32	3.82
NO₃⁻	CD₃CN	8.57	7.34	3.83
ClO₄⁻	CD₃CN	8.45	7.33	3.82
BF₄⁻	CD₃CN	8.43	7.33	3.82
H₂PO₄⁻	CDCl₃	10.26	7.30	4.09
HSO₄⁻	CDCl₃	10.19	7.34	4.09
CF₃SO₃⁻	CD₃CN	8.45	7.33	3.82
SCN⁻	CD₃CN	8.44	7.33	3.83

^a Solution concentrations are 0.02 M.

Table 9. ¹H-NMR chemical shift values of imidazolium salts [hmim][A] and [dmim][A] in CDCl₃ (300 MHz) at 298 K ^a,b. Molecules 17 04007 i004

**Table 9.** ¹H-NMR chemical shift values of imidazolium salts **[hmim][A]** and **[dmim][A]** in CDCl₃ (300 MHz) at 298 K ^a,b.
Cation	Anion	H-2	H-4	H-5	C_nH_n+1	Me	A⁻
hmim	Cl⁻	10.80	7.44	7.31	4.30; 1.89; 1.30; 0.86	4.11	–
	Ibu⁻	9.72	7.08	7.01	4.05; 1.74; 1.26; 0.86	3.75	7.28; 7.01; 3.54;2.37; 1.78; 1.41; 0.86
dmim	Cl⁻	10.82	7.38	7.27	4.32; 1.89; 1.27; 0.86	4.12	–
	Ibu⁻	10.58	7.01	6.99	4.11; 1.78; 1.25; 0.87	3.81	7.31; 6.98; 3.60;2.39; 1.79; 1.46; 0.87

^a Solution concentrations are in the range of 0.015 to 0.025 M; ^b H-4 and H-5 assignments were made according [bmim]I.

Table 10. ¹H-NMR chemical shift values of 1-butyl-2,3-dimethylimidazolium salt [bm₂im][A] in CDCl₃ (300 MHz) at 298 K ^a. Molecules 17 04007 i005

**Table 10.** ¹H-NMR chemical shift values of 1-butyl-2,3-dimethylimidazolium salt **[bm₂im][A]** in CDCl₃ (300 MHz) at 298 K ^a.
Anion	H-4	H-5	Me-2	Me-3	Bu	A⁻
AcO⁻	7.58	7.36	2.59	3.82	4.06; 1.67; 1.26; 0.86	1.72
BzO⁻	7.54	7.27	2.50	3.71	3.90; 1.58; 1.23; 0.85	7.97; 7.27
(S)-Lactate⁻	7.49	7.26	2.70	3.92	4.12; 1.79; 1.40; 0.98	3.87; 1.30
MeSO₃⁻	7.47	7.27	2.69	3.94	4.14; 1.80; 1.38; 0.98	2.74
Bu₂PO₄⁻	7.55	7.27	2.68	3.92	4.13; 1.76; 1.37; 0.96	3.77; 1.56; 1.37; 0.89
Br^−b	7.76	7.56	2.83	4.04	4.24; 1.81; 1.40; 0.98
I⁻	7.60	7.46	2.80	3.98	4.18; 1.80; 1.39; 0.94
PF₆⁻	7.46	7.30	2.70	3.90	4.11; 1.79; 1.40; 0.96
BF₄⁻	7.40	7.27	2.68	3.88	4.10; 1.79; 1.40; 0.97
CF₃SO₃⁻	7.32	7.22	2.66	3.86	4.09; 1.80; 1.40; 0.97
NCS⁻	7.43	7.32	2.77	3.96	4.17; 1.83; 1.43; 0.98
Ph₄B⁻	6.38	6.28	2.39	2.98	3.36; 1.52; 1.25; 0.92	7.46; 6.99; 6.83
Ph₄B^−c	7.63	7.60	2.56	3.73	4.09; 1.68; 1.29; 0.90	7.17; 6.92; 6.78
Ibu⁻	7.30	7.07	2.37	3.57	3.88; 1.56; 1.22; 0.85	7.23; 6.94; 3.45; 2.33; 1.73; 1.33; 0.81

^a Solution concentrations are 0.02 M; ^b Unambiguous assignments were made by NOESY-1D (400 MHz); ^c In DMSO-d₆.

Table 11. ¹H-NMR chemical shift values of 1-butyl-4-methylpyridinium salt [bmpy][A] in CDCl₃ (300 MHz) at 298 K ^a. Molecules 17 04007 i006

**Table 11.** ¹H-NMR chemical shift values of 1-butyl-4-methylpyridinium salt **[bmpy][A]** in CDCl₃ (300 MHz) at 298 K ^a.
Anion	H-2,6	H-3,5	Me	Bu	A⁻
AcO⁻	9.35	7.82	2.62	4.82; 1.96; 1.35; 0.94	1.96
BzO⁻	8.94	7.70	2.47	4.67; 1.82; 1.25; 0.83	8.00; 7.31
(S)-Lactate⁻	9.05	7.81	2.57	4.65; 1.88; 1.35; 0.87	3.89; 1.26
MeSO₃⁻	9.09	7.83	2.57	4.65; 1.91; 1.32; 0.87	2.68
Bu₂PO₄⁻	9.36	7.83	2.53	4.72; 1.89; 1.30; 0.83	3.78; 1.50; 1.30; 0.83
I⁻	9.24	7.90	2.66	4.84; 2.00; 1.41; 0.95
PF₆⁻	8.60	7.80	2.66	4.54; 1.95; 1.39; 0.95
BF₄⁻	8.73	7.82	2.66	4.60; 1.95; 1.39; 0.95
CF₃SO₃⁻	8.80	7.82	2.65	4.60; 1.94; 1.38; 0.94
NCS⁻	8.94	7.91	2.70	4.77; 2.03; 1.44; 0.99

^a Solution concentrations are 0.02 M.

Table 12. ¹H-NMR chemical shift values of 1,3-bis(mesityl)imidazolium salt 1·A in CDCl₃ (300 MHz) at 298 K ^a. Molecules 17 04007 i007

**Table 12.** ¹H-NMR chemical shift values of 1,3-bis(mesityl)imidazolium salt **1·A** in CDCl₃ (300 MHz) at 298 K ^a.
Anion	H-2		H-4,5		Me-2',6'		Me-4'		H-3'		A⁻
AcO⁻	11.54		7.46		2.20		2.35		7.04		2.16
BzO⁻	11.03		7.44		2.07		2.25		6.87		7.63; 7.14
(S)-lactate⁻	10.31		7.56		2.10		2.32		7.00		3.65; 1.04
MeSO₃⁻	9.83		7.63		2.09		2.31		6.98		2.31
Bu₂PO₄⁻	10.76		7.67		2.12		2.30		6.97		3.43; 1.32; 1.20; 0.79
Cl⁻	10.98		7.57		2.20		2.34		7.03
PF₆⁻	8.77		7.57		2.14		2.37		7.07
BF₄⁻	9.19		7.57		2.09		2.32		6.99
CF₃SO₃⁻	9.29		7.57		2.09		2.34		7.01
SCN⁻	9.70	7.63		2.19		2.37		7.08
Ph₄B⁻	6.32	7.06		2.02		2.20		6.77		7.30; 6.88; 6.77
Ph₄B^−b	9.64	8.25		2.11		2.35		7.20		7.18; 6.92; 6.78

^a Solution concentrations are in the range of 0.01 to 0.02 M; ^b In DMSO-d₆.

Table 13. ¹H-NMR chemical shift values of 1,3-dibutyl-5,6-dimethylbenzimidazolium salt 2·A in CDCl₃ (300 MHz) at 298 K ^a. Molecules 17 04007 i008

**Table 13.** ¹H-NMR chemical shift values of 1,3-dibutyl-5,6-dimethylbenzimidazolium salt **2·A** in CDCl₃ (300 MHz) at 298 K ^a.
Anion	H-2	H-4,7	Me	Bu	A⁻
AcO⁻	11.86	7.37	2.46	4.55; 1.96; 1.42; 0.97	2.03
BzO⁻	11.91	7.37	2.45	4.56; 2.00; 1.41; 0.93	8.11; 7.34
(S)-lactate⁻	11.39	7.36	2.43	4.49; 1.92; 1.37; 0.93	4.03; 1.37
MeSO₃⁻	10.63	7.40	2.47	4.53; 1.98; 1.44; 0.99	2.84
Bu₂PO₄⁻	11.52	7.36	2.45	4.57; 1.96; 1.41; 0.97	3.90; 1.62; 1.41; 0.90
I⁻	10.98	7.43	2.46	4.55; 2.02; 1.46; 0.99
PF₆⁻	9.25	7.43	2.48	4.41; 1.97; 1.43; 0.99
BF₄⁻	9.33	7.48	2.45	4.43; 1.94; 1.40; 0.94
CF₃SO₃⁻	9.86	7.42	2.47	4.48; 1.97; 1.43; 0.98
SCN⁻	10.13	7.43	2.48	4.53; 2.02; 1.47; 1.00

^a Solution concentrations are 0.02 M.

Table 14. ¹H-NMR chemical shift values of quaternary ammonium salts [Cho][A] and [d₂m₂N][A] (300 MHz) at 298 K. Molecules 17 04007 i009

**Table 14.** ¹H-NMR chemical shift values of quaternary ammonium salts **[Cho][A]** and [**d₂m₂N][A]** (300 MHz) at 298 K.
Cation	Anion	Solvent	Me	N⁺-CH₂-CH₂-OH	A⁻
Cho	I⁻	CD₃CN	3.12	3.95; 3.41; 3.59(OH)	–
	( S)-Lactate⁻	CD₃CN	3.13	3.95; 3.43; 3.67(OH)	3.78; 1.19
				N⁺-C_nH_n+1
d₂m₂N	Br⁻	CDCl₃	3.41	3.51; 1.65; 1.30; 0.88	–
	Ibu⁻	CDCl₃	3.01	3.10; 1.52; 1.26; 0.88	7.30; 7.00; 3.57;2.39; 1.81; 1.42; 0.88

4. Conclusions

Faced with a large variety of quaternary imidazolium and ammonium salts, the present study using an anion exchange resin (A⁻ form) in non-aqueous media was based on a choice of eleven examples taken from the IL pool [IL]X that could serve to evaluate the halide-for-anion swap. Significant aspects of the reported AER (A⁻ form) process are: (i) the anion loading of the AER (OH⁻ form) with acids and ammonium salts in solvent mixtures of different polarities according to the hydrophobicity of the anion source; (ii) the anion exchange using the AER (A⁻ form) method in organic solvents was easily applied to several imidazolium, benzimidazolium, pyridinium and ammonium salts, the halide-for-anion exchange progressing in excellent to quantitative yields. Depending on the hydrophobic nature of the targeted organic salts, the counteranion exchange was accomplished in organic solvents of variable polarity and dipolar nonhydroxylic organic solvent mixtures ranging from the lowest proportions of water or methanol to lipophylic solvent mixtures such as CH₃CN:CH₂Cl₂ (3:7).

On the whole, the AER (A⁻ form) method in organic solvents is a method of choice for exchanging the halide anions for a variety of anions in quaternary heteroaromatic and ammonium salts, simultaneously removing halide impurities, which is often a troublesome task. This anion exchange method could be adapted to a wide array of charged molecules crucial to advances in interdisciplinary fields in chemistry.

Acknowledgments

The authors thank to the University of Barcelona for support, SCT-UB for the use of their instruments, the D.G.I. (MICINN) Project CTQ2010-15251/BQU and the AGAUR (Generalitat de Catalunya), Grup de Recerca Consolidat 2009SGR562. Thanks are also due to Lucy Brzoska for helpful discussion on semantics and style.

References and Notes

Sowmiah, S.; Srinivasadesikan, V.; Tseng, M.-C.; Chu, Y.-H. On the chemical stabilities of ionic liquids. Molecules 2009, 14, 3780–3813. [Google Scholar]
MacFarlane, D.R.; Pringle, J.M.; Howlett, P.C.; Forsyth, M. Ionic liquids and reactions at the electrochemical interface. Phys. Chem. Chem. Phys. 2010, 12, 1659–1669. [Google Scholar]
Dupont, J.; Scholten, J.D. On the structural and surface properties of transition-metal nanopartícules in ionic liquids. Chem. Soc. Rev. 2010, 39, 1780–1804. [Google Scholar]
Hallett, J.P.; Welton, T. Room-temperature ionic liquids: Solvents for synthesis and catalysis. 2. Chem. Rev. 2011, 111, 3508–3576. [Google Scholar] [CrossRef]
le Bideau, J.; Viau, L.; Vioux, A. Ionogels, ionic liquid based hybrid materials. Chem. Soc. Rev. 2011, 40, 907–925. [Google Scholar]
Plechkova, N.V.; Seddon, K.R. Applications of ionic liquids in the chemical industry. Chem. Soc. Rev. 2008, 37, 123–150. [Google Scholar]
Stoimenovski, J.; MacFarlane, D.R.; Bica, K.; Rogers, R.D. Crystalline vs. ionic liquid salt forms of active pharmaceutical ingredients: A position paper. Pharm. Res. 2010, 27, 521–526. [Google Scholar] [CrossRef]
Deetlefs, M.; Seddon, K.R. Assessing the greenness of some typical laboratory ionic liquid preparations. Green Chem. 2010, 12, 17–30. [Google Scholar]
Yau, H.M.; Chan, S.J.; George, S.R.D.; Hook, J.M.; Croft, A.K.; Harper, J.B. Ionic liquids: Just molten salts after all? Molecules 2009, 14, 2521–2534. [Google Scholar] [CrossRef]
Petkovic, M.; Seddon, K.R.; Rebelo, L.P.N.; Pereira, C.S. Ionic liquids: A pathway to environmental acceptability. Chem. Soc. Rev. 2011, 40, 1383–1403. [Google Scholar]
Sun, N.; Rodríguez, H.; Rahmana, M.; Rogers, R.D. Where are ionic liquid strategies most suited in the pursuit of chemicals and energy from lignocellulosic biomass? Chem. Commun. 2011, 47, 1405–1421. [Google Scholar]
Alcalde, E.; Dinarès, I.; Mesquida, N. Imidazolium-based receptors. Top. Heterocycl. Chem. 2010, 24, 267–300. [Google Scholar]
Clare, B.; Sirwardana, A.; MacFarlane, D.R. Synthesis and purification of ionic liquids. Top. Curr. Chem. 2009, 290, 1–40. [Google Scholar]
Olivier-Bourbigou, H.; Magna, L.; Morvan, D. Ionic liquids and catalysis: Recent progress from knowledge to applications. Appl. Catal. A 2010, 373, 1–56. [Google Scholar]
Smiglak, M.; Hines, C.C.; Rogers, R.D. New hydrogen carbonate precursors for efficient and byproduct-free syntheses of ionic liquids based on 1,2,3-trimethylimidazolium and N,N-dimethylpyrrolidinium cores. Green Chem. 2010, 12, 491–501. [Google Scholar] [CrossRef]
Nockemann, P.; Thijs, B.; Driesen, K.; Janssen, C.R.; van Hecke, K.; van Meervelt, L.; Kossmann, S.; Kirchner, B.; Binnemans, K. Choline saccharinate and choline acesulfamate: Ionic liquids with low toxicities. J. Phys. Chem. B 2007, 111, 5254–5263. [Google Scholar]
Alcalde, E.; Dinarès, I.; Fayet, J.-P.; Vertut, M.-C.; Elguero, J. Synthesis of highly dipolar betaines: Pyridinium azolates. J. Chem. Soc. Chem. Commun. 1986, 734–735. [Google Scholar]
Alcalde, E.; Alemany, M.; Pérez-García, L.; Rodríguez, M.L. Non-classical [1₄]metaheterophanes containing betaine units. Synthesis, NMR spectroscopy, and X-ray crystallography. J. Chem. Soc. Chem. Commun. 1995, 1239–1240. [Google Scholar]
Alcalde, E.; Alemany, M.; Gisbert, M. A direct synthetic approach to novel quadrupolar [1₄] azolophanes. Tetrahedron 1996, 52, 15171–15188. [Google Scholar]
Alcalde, E.; Alvarez-Rúa, C.; García-Granda, S.; García-Rodriguez, E.; Mesquida, N.; Pérez-García, L. Hydrogen bonded driven anion binding by dicationic [1₄] imidazoliophanes. Chem. Commun. 1999, 295–296. [Google Scholar]
Alcalde, E.; Mesquida, N.; Vilaseca, M.; Alvarez-Rúa, C.; García-Granda, S. Imidazolium-based dicationic cyclophanes. Solid-state aggregates with unconventional (C-H)⁺···Cl− hydrogen bonding revealed by X-ray diffraction. Supramol. Chem. 2007, 19, 501–509. [Google Scholar] [CrossRef]
Dinarès, I.; de Miguel, C.G.; Mesquida, N.; Alcalde, E. Bis(imidazolium)-calix[4]arene receptors for anion binding. J. Org. Chem. 2009, 74, 482–485. [Google Scholar]
Ogihara, W.; Yoshizawa, M.; Ohno, H. Novel ionic liquids composed of only azole ions. Chem. Lett. 2004, 33, 1022–1023. [Google Scholar]
Fukumoto, K.; Yoshizawa, M.; Ohno, H. Room temperature ionic liquids from 20 natural amino acids. J. Am. Chem. Soc. 2005, 127, 2398–2399. [Google Scholar]
Fukaya, Y.; Iizuka, Y.; Sekikawa, K.; Ohno, H. Bio ionic liquids: Room temperature ionic liquids composed wholly of biomaterials. Green Chem. 2007, 9, 1155–1157. [Google Scholar]
Ou, G.; Zhu, M.; Shea, J.; Yuan, Y. Ionic liquid buffers: A new class of chemicals with potential for controlling pH in non-aqueous media. Chem. Commun. 2006, 4626–4628. [Google Scholar]
Lall, S.I.; Mancheno, D.; Castro, S.; Behaj, V.; Cohen, J.I.; Engel, R. Polycations. Part X. LIPs, a new category of room temperature ionic liquid based on polyammonium salts. Chem. Commun. 2000, 2413–2414. [Google Scholar]
Golding, J.; Forsyth, S.; MacFarlane, D.R.; Forsyth, M.; Deacon, G.B. Methanesulfonate and p-toluenesulfonate salts of the N-methyl-N-alkylpyrrolidinium and quaternary ammonium cations: Novel low cost ionic liquids. Green Chem. 2002, 4, 223–229. [Google Scholar] [CrossRef]
Machado, M.Y.; Dorta, R. Synthesis and characterization of chiral imidazolium salts. Synthesis 2005, 2473–2475. [Google Scholar]
Nobuoka, K.; Kitaoka, S.; Kunimitsu, K.; Iio, M.; Harran, T.; Wakisaka, A.; Ishikawa, Y. Camphor ionic liquid: Correlation between stereoselectivity and cation-anion interaction. J. Org. Chem. 2005, 70, 10106–10108. [Google Scholar]
Ruiz-Toral, A.; de los Ríos, A.P.; Hernández, F.J.; Janssen, M.H.A.; Schoevaart, R.; van Rantwijk, F.; Sheldon, R.A. Cross-linked Candida antarctica lipase B is active in denaturing ionic liquids. Enzyme Microb. Technol. 2007, 40, 1095–1099. [Google Scholar]
Dinarès, I.; de Miguel, C.G.; Ibáñez, A.; Mesquida, N.; Alcalde, E. Imidazolium ionic liquids: A simple anion exchange protocol. Green Chem. 2009, 11, 1507–1510. [Google Scholar]
Alcalde, E.; Dinarès, I.; Ibáñez, A.; Mesquida, N. A general halide-to-anion switch for imidazolium-based ionic liquids and oligocationic systems using anion exchange resins (A⁻ form). Chem. Commun. 2011, 47, 3266–3268. [Google Scholar]
Viau, L.; Tourné-Péteilh, C.; Devoisselle, J.-M.; Vioux, A. Ionogels as drug delivery system: One-step sol-gel synthesis using imidazolium ibuprofenate ionic liquid. Chem. Commun. 2010, 46, 228–230. [Google Scholar]
Dupont, J.; Suarez, P.A.Z.; de Souza, R.F.; Burrow, R.A.; Kintzinger, J.-P. C-H—π interactions in 1-n-Butyl-3-methylimidazolium Tetraphenylborate molten salt: Solid and solution structures. Chem.-Eur. J. 2000, 6, 2377–2381. [Google Scholar]
Yong, L.; Yao, M.-L.; Green, J.F.; Kelly, H.; Kabalka, G.W. Syntheses and characterization of polymer-supported organotrifluoroborates: Applications in radioiodination reactions. Chem. Commun. 2010, 46, 2623–2625. [Google Scholar]
MacFarlane, D.R.; Pringle, J.M.; Johansson, K.M.; Forsyth, S.A.; Forsyth, M. Lewis base ionic liquids. Chem. Commun. 2006, 1905–1917. [Google Scholar]
Rodríguez, H.; Gurau, G.; Holbreya, J.D.; Rogers, R.D. Reaction of elemental chalcogens with imidazolium acetates to yield imidazole-2-chalcogenones: Direct evidence for ionic liquids as proto-carbenes. Chem. Commun. 2011, 47, 3222–3224. [Google Scholar]
Lee, K.M.; Lee, C.K.; Lin, I.J.B. First example of interdigitated U-shape benzimidazolium ionic liquid crystals. Chem. Commun. 1997, 899–900. [Google Scholar]
Wang, K.F.; Jian, F.F.; Zhuang, R.R.; Xiao, H.L. New ionic liquids of N,N'-dialkylbenzimidazolium salt comprising copper(II) ions. Cryst. Growth Des. 2009, 9, 3934–3940. [Google Scholar] [CrossRef]
Wang, K.F.; Jian, F.F.; Zhuang, R.R. A new ionic liquid comprising lanthanum(III) bulk-modified carbon paste electrode: Preparation, electrochemistry and electrocatalysis. Dalton Trans. 2009, 4532–4537. [Google Scholar]
Zhuang, R.R.; Jian, F.F.; Wang, K.F. A new binuclear Cd(II)-containing ionic liquid: Preparation and electrocatalytic activities. J. Organomet. Chem. 2009, 694, 3614–3618. [Google Scholar]
Arduengo, A.J., III. Looking for stable carbenes: The difficulty in starting anew. Acc. Chem. Res. 1999, 32, 913–921. [Google Scholar]
Vijayaraghavan, R.; Thompson, B.C.; MacFarlane, D.R.; Kumar, R.; Surianarayanan, M.; Aishwarya, S.; Sehgal, P.K. Biocompatibility of choline salts as crosslinking agents for collagen based biomaterials. Chem. Commun. 2010, 46, 294–296. [Google Scholar]
Hough, W.L.; Smiglak, M.; Rodríguez, H.; Swatloski, R.P.; Spear, S.K.; Daly, D.T.; Pernak, J.; Grisel, J.E.; Carliss, R.D.; Soutullo, M.D.; et al. The third evolution of ionic liquids: Active pharmaceutical ingredients. New J. Chem. 2007, 31, 1429–1436. [Google Scholar] [CrossRef]
Clare, B.R.; Bayley, P.M.; Best, A.S.; Forsyth, M.; MacFarlane, D.R. Purification or contamination? The effect of sorbents on ionic liquids. Chem. Commun. 2008, 2689–2691. [Google Scholar]
Burrell, A.K.; del Sesto, R.E.; Baker, S.N.; McCleskey, T.M.; Baker, G.A. The large scale synthesis of pure imidazolium and pyrrolidinium ionic liquids. Green Chem. 2007, 9, 449–454. [Google Scholar]
Wang, J.; Cao, W.-F.; Su, J.-H.; Tian, H.; Huang, Y.-H.; Sun, Z.-R. Syntheses and nonlinear absorption of novel unsymmetrical cyanines. Dyes Pigm. 2003, 57, 171–179. [Google Scholar]
Arduengo, A.J., III; Krafczyk, R.; Schmutzler, R. Imidazolylidenes, imidazolinylidenes and imidazolidines. Tetrahedron 1999, 55, 14523–l4534. [Google Scholar] [CrossRef]

Sample Availability: Samples of all compounds are available from the authors.

© 2012 by the authors; licensee MDPI, Basel, Switzerland. This article is an open-access article distributed under the terms and conditions of the Creative Commons Attribution license (http://creativecommons.org/licenses/by/3.0/).

Share and Cite

MDPI and ACS Style

Alcalde, E.; Dinarès, I.; Ibáñez, A.; Mesquida, N. A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids. Molecules 2012, 17, 4007-4027. https://doi.org/10.3390/molecules17044007

AMA Style

Alcalde E, Dinarès I, Ibáñez A, Mesquida N. A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids. Molecules. 2012; 17(4):4007-4027. https://doi.org/10.3390/molecules17044007

Chicago/Turabian Style

Alcalde, Ermitas, Immaculada Dinarès, Anna Ibáñez, and Neus Mesquida. 2012. "A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids" Molecules 17, no. 4: 4007-4027. https://doi.org/10.3390/molecules17044007

Article Menu

A Simple Halide-to-Anion Exchange Method for Heteroaromatic Salts and Ionic Liquids

Abstract

1. Introduction