Engineering Proceedings, Volume 64, Issue 1

In order to fulfil the environmental goals set for the coming years, industrial companies are motivated to look for clean technologies and green solutions. Replacing common fuels in the transport sector can also contribute to the reduction of emissio...

The 30th International Scientific Conference on Modern Metallurgy—Iron and Steelmaking 2023 (IaSM 2023) was organized by the Faculty of Materials, Metallurgy, and Recycling at the Technical University of Košice in Slovakia, in collaborat...

In submitting the conference proceedings to Engineering Proceedings, the volume editors of the proceedings certify with the publisher that all the papers published in this volume have been subjected to peer review administered by the volume editors [...

This publication presents the chemical compositions of carbon reducers used in the production of ferroalloys, with particular emphasis on the content of Al, Ca, Mg, Mn, Cr, Ti, P, or S in their mineral substances. A certain amount of these elements i...

This study presents the development of a novel material for a spherical impact pad for tundishes during steel production, focusing on improving steel cleanliness and flow optimization. Traditional low-carbon and ultra-low carbon concrete (LCC/ULCC) m...

Using 3D scanning, coordinate measuring machine, and roughness measurements we evaluated and compared zinc alloy castings produced in conventionally and additively manufactured shaped mould parts. Tests were conducted on castings from new shaped part...

The metallurgical sector, a key component of European industries, plays a crucial role both in advanced economies and in the infrastructure development of emerging nations. As environmental concerns increasingly influence global trade policies, the i...

Foundries, to the same extent today as in the past, represent one of the strategic branches of all industry. In fact, all aspects of modern life depend on the casting and production of brake discs, medical implants, marine engines, and even aircraft...

Foundry Degassing Units (FDU) are used for refining aluminum alloys. For an ideal refining process using an FDU unit, it is necessary to select several parameters, which are linked to each other. For a rotary impeller, we searched for several paramet...

In the present paper, microstructural changes in two alloys, IN617 and DMV617 mod, after 5 h and 1000 h of aging at 700 °C were investigated using scanning transmission electron microscopy. The mechanical properties of the samples were evaluated...

Reducing energy consumption and increasing energy efficiency have been especially topical issues recently, affecting all areas of energy consumption, including industrial sectors. Continuous annealing lines, as important industrial production facilit...

The production of iron castings in cupola furnaces is a significant industrial process that has a notable impact on the environment. This paper examines and describes the environmental impact of this process, specifically focusing on the generation,...

Hydrogen is a key element in the changing energy sector and presents an accessible alternative to conventional fossil fuel sources. In this work, a system of ten high-entropy alloys was prepared based on the Hume-Rothery rules. One of the biggest adv...

The conversion of locally available, low-value materials to useful products and media, thereby replacing high-quality and high-cost resources, belongs to one of the pillars of the circular economy of industrial conditions. A study on the potential im...

This paper presents the results of increasing the hydrogen concentration in natural gas distributed within the territory of the Slovak Republic. The range of hydrogen concentrations in the mathematical model is considered to be from 0 to 100 vol.% fo...

The article deals with the use of computed tomography, an advanced method for evaluating the quality of aluminium castings. Casting quality is a key factor in ensuring safety and reliability in industrial applications. Computed tomography is a compre...

In previous work, a small electric furnace with a capacity of 3.5 kg of liquid copper, capable of reaching temperatures up to 1200 °C, and with nominal power input of 2.1 or 6.2 kW at 230 V was designed and constructed. The purpose of this furnac...

Pyrometallurgical copper production is carried out in thermal aggregates. Input waste materials with a copper content between 5% and 99% Cu are treated in the individual aggregates. In a shaft furnace, except for molten black copper, slag and shaft f...

The aim of the presented research was to optimize a pig iron desulfurization process through data-driven machine learning methods. Utilizing historical data, chemical analysis of pig iron and slag, and the thermodynamics of the process including simu...

Copper converter flue dust (CFD) is one of the solid wastes generated during the pyrometallurgical production of secondary copper. Due to its fine-grained character and its content of toxic heavy metals, CFD is classified as hazardous waste. CFD cont...