Search Results (8)

The use of an electron beam (EB) as a heating source in EB-based powder bed fusion (PBF-EB) has several limitations, such as reduced powder recyclability, short machine service intervals, difficulties with heating large areas and the limited processability of charge-sensitive powders. Near-infrared (NIR) heating was recently introduced as a feasible replacement and/or complement to EB heating in PBF-EB. This work further investigates the feasibility of using NIR to eliminate the need for a build platform as well as to enable easier repairing of parts in PBF-EB. NIR-assisted Ti-6Al-4V builds were successfully carried out by starting from a loose powder bed without using a build platform. The results do not only confirm that it is possible to eliminate the build platform by the aid of NIR, but also that it can be beneficial for the process cleanliness and improve the surface quality of built parts. Furthermore, a 430 stainless-steel (SS) component could be repaired by positioning it in a loose 316L SS powder bed using a fully NIR-heated PBF-EB process. Full article

We suggest a novel approach for searching natural compounds with anti-aging and rejuvenation potential using cell cultures, with a high potential for the further in vivo applications. The present paper discusses ways of defining age for cell populations with large numbers of cells and suggests a method of assessing how young or old a cell population is based on a cell age profile approach. This approach uses experimental distributions of the cells over the cell cycle stages, acquired using flow cytometry. This paper discusses how such a profile should evolve under homeostatic maintenance of cell numbers in the proliferation niches. We describe promising results from experiments on a commercial substance claiming rejuvenating and anti-aging activity acting upon the cultures of human mononuclear cells and dermal fibroblasts. The chosen substance promotes a shift towards larger proportion of cells in synthesis and proliferation stages, and increases cell culture longevity. Further, we describe promising in vivo testing results of a selected food supplement. Based on the described concept of cell age profile and available test results, a strategy to search for natural compounds with regenerative, anti-aging and rejuvenation potential is suggested and proposed for wider and thorough testing. Proposed methodology of age assessment is rather generic and can be used for quantitative assessment of the anti-aging and rejuvenation potential of different interventions. Further research aimed at the tests of the suggested strategy using more substances and different interventions, and the thorough studies of molecular mechanisms related to the action of the substance used for testing the suggested search methodology, are needed. Full article

Aging is a global phenomenon, and the use of exercise technology by older adults can help them to prevent disease, achieve good health, and ultimately achieve successful aging. In the past, there literature compilation studies have been conducted on sports technology and young people or on the use of technology by the older adults; however, no studies have determined the attitudes of older adults toward sports technology. This review applied a systematic literature analysis to determine the factors that correlate the technology acceptance model with the older population’s exercise attitudes. A total of 10 studies were identified as contributing to the use of exercise technology by older adults. The main findings of this review are that, of the 28 factors identified in the 10 studies, only 18 were identified as factors influencing older adults’ use of sports technology in the technology acceptance model (TAM). Among these, fifteen factors affected intention, four factors affected perceived ease of use, three factors affected perceived usefulness, and two factors affected attitudes. Finally, discussing the related factors affecting TAM allows us to provide suggestions for future research directions. Full article

Targeting biomedical applications, Triply Periodic Minimal Surface (TPMS) gyroid sheet-based structures were successfully manufactured for the first time by Electron Beam Melting in two different production Themes, i.e., inputting a zero (Wafer Theme) and a 200 µm (Melt Theme) wall thickness. Initial assumption was that in both cases, EBM manufacturing should yield the structures with similar mechanical properties as in a Wafer-mode, as wall thickness is determined by the minimal beam spot size of ca 200 µm. Their surface morphology, geometry, and mechanical properties were investigated by means of electron microscopy (SEM), X-ray Computed Tomography (XCT), and uniaxial tests (both compression and tension). Application of different manufacturing Themes resulted in specimens with different wall thicknesses while quasi-elastic gradients for different Themes was found to be of 1.5 GPa, similar to the elastic modulus of human cortical bone tissue. The specific energy absorption at 50% strain was also similar for the two types of structures. Finite element simulations were also conducted to qualitatively analyze the deformation process and the stress distribution under mechanical load. Simulations demonstrated that in the elastic regime wall, regions oriented parallel to the load are primarily affected by deformation. We could conclude that gyroids manufactured in Wafer and Melt Themes are equally effective in mimicking mechanical properties of the bones. Full article

The term “critical raw materials” (CRMs) refers to various metals and nonmetals that are crucial to Europe’s economic progress. Modern technologies enabling effective use and recyclability of CRMs are in critical demand for the EU industries. The use of CRMs, especially in the fields of biomedicine, aerospace, electric vehicles, and energy applications, is almost irreplaceable. Additive manufacturing (also referred to as 3D printing) is one of the key enabling technologies in the field of manufacturing which underpins the Fourth Industrial Revolution. 3D printing not only suppresses waste but also provides an efficient buy-to-fly ratio and possesses the potential to entirely change supply and distribution chains, significantly reducing costs and revolutionizing all logistics. This review provides comprehensive new insights into CRM-containing materials processed by modern additive manufacturing techniques and outlines the potential for increasing the efficiency of CRMs utilization and reducing the dependence on CRMs through wider industrial incorporation of AM and specifics of powder bed AM methods making them prime candidates for such developments. Full article

The present paper describes preliminary results of studies carried out using a new measurement setup and a biathlon rifle with two different interchangeable stocks: a commercial, mainly wooden one and one additively manufactured from titanium alloy and a polymer PA 2200, employing lightweight, 3D lattice architecture. A finite element analysis of the predicted mechanical properties of new design elements was carried out prior to the manufacturing. Experiments were carried out using a novel setup for the assessment of athlete and rifle performance in biathlon shooting. Data acquisition was carried out at the rates of few kilosamples per second, using a combination of an airbag-based rifle butt pressure sensor, a trigger loading sensor, strap load cell, and two tri-axis MEMS sensors—an accelerometer and a gyroscope. All tests indicate that a rifle stock additively manufactured from titanium alloy could provide better recoil damping compared to the commercial, mainly wooden one. Together with the high capacity of additive manufacturing technologies in equipment individualization, this may provide additional possibilities for the improvement of sports rifle construction and help athletes achieve better results in competitions. Full article

the wind tunnel at the SportsTech Research Centre at Mid Sweden University (MIUN, Ostersund) was opened in 2015 for sports technology research. It is dedicated to analysis of equipment performance and garment development and suitable for roller skiing, running and cycling. The aim of this work was to develop and apply a full-scale method to investigate the aerodynamic behaviour of a cyclist facing front and cross wind at different yaw angles (from 0° to 30°) and speeds. To reach this goal, a rotating structure supported by a force platform was constructed. It includes a set of rollers on which fully unrestrained cycling is possible. The method was applied to the comparison of three wheelsets (differing in material, height and shape of the rim, number and shape of spokes) in terms of drag and side aerodynamic forces during a cyclist’s ride at 30 km/h, while keeping all the other factors constant. Resulting curves allowed estimating differences of 4% and 9% when applied to a recent time trial competition with supposed wind conditions. Full article

A novel Human Head Surrogate was obtained from available MRI scans of a 50th percentile male human head. Addictive manufacturing was used to produce the skull, the brain and the skin. All original MRI geometries were partially smoothed and adjusted to provide the best biofidelity compatible with printing and molding technology. The skull was 3D-printed in ABS and ten pressure sensors were placed into it. The brain surrogate was cast from silicon rubber in the 3D-printed plastic molds. Nine tri-axial accelerometers (placed at the tops of the lobes, at the sides of the lobes, in the cerebellum and in the center of mass) and a three-axis gyroscope (at the center of mass) were inserted into the silicon brain during casting. The cranium, after assembly with brain, was filled with silicon oil mimicking the cerebral fluid. Silicon rubber was cast in additional 3D-printed molds to form the skin surrounding the cranium. The skull base was adapted to be compatible with the Hybrid-III neck and allow the exit of brain sensors cabling. Preliminary experiments were carried out proving the functionality of the surrogate. Results showed how multiple accelerometers and pressure sensors allowed a better comprehension of the head complex motion during impacts. Full article