Search Results (22)

In the development of high-temperature and high-salinity oil fields, biopolymer scleroglucan flooding technology faces significant challenges. Traditional scleroglucan products exhibit poor injectability and high extraction costs. This study investigated the application potential of the original fermentation broth of exopolysaccharides (EPS) produced by microorganisms in a simulated high-temperature and high-salinity oil reservoir environment. The polysaccharide was identified as scleroglucan through IR and NMR analysis. Its stability and rheological properties were comprehensively evaluated under extreme conditions, including temperatures up to 150 °C, pH levels ranging from 1 to 13, and salinities up to 22 × 10⁴ mg/L. The results demonstrated that EPS maintained excellent viscosity and stability, particularly at 76.6 °C and 22 × 10⁴ mg/L salinity, where its viscosity remained above 80% for 35 days. This highlights its significant viscoelasticity and stability in high-temperature and high-salinity oil reservoirs. Additionally, this study, for the first time, examined the rheological properties of the original fermentation broth of scleroglucan, specifically assessing its injectability and enhanced oil recovery (EOR) performance in a simulated Middle Eastern high-temperature, high-salinity, medium-low permeability reservoir environment. The findings revealed an effective EOR exceeding 15%, confirming the feasibility of using the original fermentation broth as a biopolymer for enhancing oil recovery in extreme reservoir conditions. Based on these experimental results, it is concluded that the original fermentation broth of Athelia rolfsii exhibits superior performance under high-temperature and high-salinity conditions in medium–low permeability reservoirs, offering a promising strategy for future biopolymer flooding in oil field development. Full article

Water injection is the most widely used secondary recovery method, but its low viscosity limits sweep efficiency in heterogeneous carbonate reservoirs, especially when displacing heavy crude oils. Polymer flooding overcomes this by increasing the viscosity of the injected fluid and improving the mobility ratio. In this work, we compare three biopolymers (i.e., Xanthan Gum, Scleroglucan, and Guar Gum) using a core flood test on Indiana Limestone with 16–19% porosity and 180–220 mD permeability at 60 °C and 30,905 mg/L of salinity. We injected solutions at 100–1500 ppm and 0.5–6 cm³/min to measure the Resistance Factor (RF), Residual Resistance Factor (RRF), in situ viscosity, and relative injectivity. All polymers behaved as pseudoplastic fluids with no shear thickening. The RF rose from ~1.1 in the dilute regime to 5–16 in the semi-dilute regime, and the RRF spanned 1.2–5.8, indicating moderate, reversible permeability impairment. In-site viscosity reached up to eight times that of brine, while relative injectivity remained 0.5. Xanthan Gum delivered the highest viscosity boost and strongest shear thinning, Scleroglucan offered a balance of stable viscosity and a moderate RF, and Guar Gum gave predictable but lower viscosity enhancement. These results establish practical guidelines for selecting polymer types, concentration, and flow rate in reservoir-condition polymer flood designs. Full article

Scleroglucan is the extracellular polysaccharide (EPS) produced by Sclerotium rolfsii (S. rolfsii). The low EPS titer and limited substrate utilization of S. rolfsii present significant challenges in the fermentation process, restricting industrial applications of scleroglucan. In this study, we performed a transcriptomic analysis on the mycelium of S. rolfsii fermented with different carbon sources. The key genes involved in polysaccharide biosynthesis (6-phosphofructokinase 1 (PFK1), pyruvate decarboxylase (PDC), aldehyde dehydrogenase (NAD (P)+) (ALDH3), and acetyl-CoA synthase (ACS)) were identified and their roles in the process were investigated. The supplementation of specific precursors—fructose-6-phosphate, pyruvate, aldehydes, and acetate—was shown to enhance both the polysaccharide titer and substrate utilization. By adding precursors, the titer of SEPS produced in a 5 L fermentation tank reached 48.69 ± 3.8 g/L. Notably, the addition of these precursors increased the titer of EPS fermented with sucrose (SEPS) by 65.63% and substrate utilization by 119.3%, while the titer of EPS fermented with lactose (LEPS) rose by 80.29% and substrate utilization rose by 47.08%. These findings suggest that precursor supplementation can effectively improve polysaccharide production and substrate efficiency, thereby minimizing resource waste and environmental impact. Full article

This study details the synthesis and performance evaluation of a novel lightweight thermal and acoustic insulation material, resulting from the combination of a scleroglucan-based hydrogel and recycled rigid polyurethane waste powder. Through a sublimation-driven water-removal process, a porous three-dimensional network structure is formed, showcasing notable thermal and acoustic insulation properties. Experimental data are presented to highlight the material’s performance, including comparisons with commercially available mineral wool and polymeric foams. This material versatility is demonstrated through tunable mechanical, thermal and acoustic characteristics, achieved by strategically adjusting the concentration of the biopolymer and additives. This adaptability positions the material as a promising candidate for different insulation applications. Addressing environmental concerns related to rigid polyurethane waste disposal, the study contributes to the circular economy. Full article

Scleroglucan (SG) is resistant to harsh reservoir conditions such as high temperature, high shear stresses, and the presence of chemical substances. However, it is susceptible to biological degradation because bacteria use SG as a source of energy and carbon. All degradation effects lead to viscosity loss of the SG solutions, affecting their performance as an enhanced oil recovery (EOR) polymer. Recent studies have shown that nanoparticles (NPs) can mitigate these degradative effects. For this reason, the EOR performance of two new nanohybrids (NH-A and NH-B) based on carboxymethyl-scleroglucan and amino-functionalized silica nanoparticles was studied. The susceptibility of these products to chemical, mechanical, and thermal degradation was evaluated following standard procedures (API RP 63), and the microbial degradation was assessed under reservoir-relevant conditions (1311 ppm and 100 °C) using a bottle test system. The results showed that the chemical reactions for the nanohybrids obtained modified the SG triple helix configuration, impacting its viscosifying power. However, the nanohybrid solutions retained their viscosity during thermal, mechanical, and chemical degradation experiments due to the formation of a tridimensional network between the nanoparticles (NPs) and the SG. Also, NH-A and NH-B solutions exhibited bacterial control because of steric hindrances caused by nanoparticle modifications to SG. This prevents extracellular glucanases from recognizing the site of catalysis, limiting free glucose availability and generating cell death due to substrate depletion. This study provides insights into the performance of these nanohybrids and promotes their application in reservoirs with harsh conditions. Full article

In this study, two new nanohybrids (NH-A and NH-B) were synthesized through carbodiimide-assisted coupling. The reaction was performed between carboxymethyl-scleroglucans (CMS-A and CMS-B) with different degrees of substitution and commercial amino-functionalized silica nanoparticles using 4-(dimethylamino)-pyridine (DMAP) and N,N′-dicyclohexylcarbodiimide (DCC) as catalysts. The morphology and properties of the nanohybrids were investigated by using transmission (TEM) and scanning electron microscopy (SEM), electron-dispersive scanning (EDS), attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FT-IR), X-ray photoelectron spectroscopy (XPS), powder X-ray diffraction (XRD), inductively coupled plasma atomic emission spectroscopy (ICP-OES), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and dynamic light scattering (DLS). The nanohybrids exhibited differences in structure due to the incorporation of polyhedral oligomeric silsesquioxane (POSS) materials. The results reveal that hybrid nanomaterials exhibit similar thermal properties but differ in morphology, chemical structure, and crystallinity properties. Finally, a viscosity study was performed on the newly obtained nanohybrid materials; viscosities of nanohybrids increased significantly in comparison to the carboxymethyl-scleroglucans, with a viscosity difference of 7.2% for NH-A and up to 32.6% for NH-B. Full article

Biopolymers emerge as promising candidates for enhanced oil recovery (EOR) applications due to their molecular structures, which exhibit better stability than polyacrylamides under harsh conditions. Nonetheless, biopolymers are susceptible to oxidation and biological degradation. Biopolymers reinforced with nanoparticles could be a potential solution to the issue. The nanofluids’ stability and performance depend on the nanoparticles’ properties and the preparation method. The primary objective of this study was to evaluate the effect of the preparation method and the nanoparticle type (SiO₂, Al₂O₃, and TiO₂) on the viscosity and stability of the scleroglucan (SG). The thickening effect of the SG solution was improved by adding all NPs due to the formation of three-dimensional structures between the NPs and the SG chains. The stability test showed that the SG + Al₂O₃ and SG + TiO₂ nanofluids are highly unstable, but the SG + SiO₂ nanofluids are highly stable (regardless of the preparation method). According to the ANOVA results, the preparation method and standing time influence the nanofluid viscosity with a statistical significance of 95%. On the contrary, the heating temperature and NP type are insignificant. Finally, the nanofluid with the best performance was 1000 ppm of SG + 100 ppm of SiO₂_120 NPs prepared by method II. Full article

This paper presents the methodology for synthesizing and characterizing two carboxymethyl EOR-grade Scleroglucans (CMS-A and CMS-B). An O-Alkylation reaction was used to insert a hydrophilic group (monochloroacetic acid—MCAA) into the biopolymer’s anhydroglucose subunits (AGUs). The effect of the degree of the carboxymethyl substitution on the rheology and thermal stability of the Scleroglucan (SG) was also evaluated. Simultaneous thermal analysis (STA/TGA-DSC), differential scanning calorimetry (DSC), X-ray Diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Scanning Electron Microscopy, and Energy Dispersive Spectroscopy (SEM/EDS) were employed to characterize both CMS products. FTIR analysis revealed characteristic peaks corresponding to the carboxymethyl functional groups, confirming the modification. Also, SEM analysis provided insights into the structural changes in the polysaccharide after the O-Alkylation reaction. TGA results showed that the carboxymethylation of SG lowered its dehydroxylation temperature but increased its thermal stability above 300 °C. The CMS products and SG exhibited a pseudoplastic behavior; however, lower shear viscosities and relaxation times were observed for the CMS products due to the breakage of the SG triple helix for the chemical modification. Despite the viscosity results, the modified Scleroglucans are promising candidates for developing new engineering materials for EOR processes. Full article

The chemically synthesized polymer polyacrylamide (HPAM) has achieved excellent oil displacement in conventional reservoirs, but its oil displacement is poor in extreme reservoir environments. To develop a biopolymer oil flooding agent suitable for extreme reservoir conditions, the viscosity changes and rheological properties of three biopolymers, diutan gum, xanthan gum, and scleroglucan, were studied under extreme reservoir conditions (high salt, high temperature, strong acid, and alkali), and the effects of temperature, mineralization, pH, and other factors on their viscosities and long-term stability were analyzed and compared. The results show that the three biopolymers had the best viscosity-increasing ability at temperatures of 90 °C and below. The viscosity of the three biopolymers was 80.94 mPa·s, 11.57 mPa·s, and 59.83 mPa·s, respectively, when the concentration was 1500 mg/L and the salinity 220 g/L. At the shear rate of 250 s⁻¹, 100 °C~140 °C, scleroglucan had the best viscosification. At 140 °C, the solution viscosity was 19.74 mPa·s, and the retention rate could reach 118.27%. The results of the long-term stability study showed that the solution viscosity of scleroglucan with a mineralization level of 220 mg/L was 89.54% viscosity retention in 40 days, and the diutan gum could be stabilized for 10 days, with the viscosity maintained at 90 mPa·s. All three biopolymers were highly acid- and alkali-resistant, with viscosity variations of less than 15% in the pH3~10 range. Rheological tests showed that the unique double-helix structure of diutan gum and the rigid triple-helix structure of scleroglucan caused them to have better viscoelastic properties than xanthan gum. Therefore, these two biopolymers, diutan gum, and scleroglucan, have the potential for extreme reservoir oil displacement applications. It is recommended to use diutan gum for oil displacement in reservoirs up to 90 °C and scleroglucan for oil displacement in reservoirs between 100 °C and 140 °C. Full article

Fungal exopolysaccharides (EPSs) represent an important group of bioactive compounds secreted by fungi. These biopolymers can be utilized individually or in combination with different bioactive substances for a broad range of pharmaceutical field applications, due to their various biological activities, such as antioxidant, antimicrobial, anti-inflammatory, antiviral, anti-diabetic, and anticoagulant effects. The paper presents an up-to-date review of the main fungal polysaccharides (pullulan, schizophyllan, scleroglucan, botryosphaeran, lentinan, grifolan, and lasiodiplodan), highlighting their structures, producing strains, and useful properties in a double position, as controlled release (rate and selectively targeting) drug carriers, but mostly as active immunomodulating and antitumor compounds in cancer therapy. Full article

Scleroglucan is obtained from Sclerotium rolfsii and is widely used in many fields. In this study, transcriptomics combined with metabolomics were used to study the global metabolites and gene changes. The results of the joint analysis showed that the DEGs (differentially expressed genes) and DEMs (differentially expressed metabolites) of SEPS_48 (fermented with sucrose as a carbon source for 48 h) and GEPS_48 (fermented with glucose as a carbon source for 48 h) comparison groups were mainly related to cell metabolism, focusing on carbohydrate metabolism, amino acid metabolism, and amino sugar and nucleoside sugar metabolism. We therefore hypothesized that the significant differences in these metabolic processes were responsible for the differences in properties. Moreover, the joint analysis provides a scientific theoretical basis for fungal polysaccharides biosynthesis and provides new insights into the effects of carbon sources on the production. As an excellent bioenergy and biological product, scleroglucan can be better applied in different fields, such as the food industry. Full article

Maintaining insoluble plant-based ingredients in suspension and ensuring long-term physical stability is particularly challenging for formulators of green cosmetics. This study aimed to evaluate the structure and applicative properties of gel and gel-cream topical formulations suitable for delivering an insoluble phytocomplex on the vaginal mucosa and maintaining its integrity. For this purpose, we studied the compatibility of Perilla frutescens (L.) Britton phytocomplex (PFP), derived from in vitro plant cell cultures and presented as a powder finely dispersed in glycerin, with different classes of natural rheological modifiers (such as xanthan gum, sclerotium gum, succinoglycan, xyloglucan, diutan gum, hydroxypropyl guar gum derivative) in gel and gel-cream formulations, to meet the needs of the cosmetic market for naturalness and biodegradability. Through rheological and texture analyses, we studied the physico–mechanical properties of the samples, comparing the performances of the chosen polysaccharides to those of acrylic polymeric rheological modifiers, evaluating their contribution in terms of stability and applicative properties. Since a weak-gel rheological pattern proved to be the optimal one to keep the actives in suspension, the associations of tamarind seed polysaccharides with succinoglycan or scleroglucan were the most suitable for the formulation of mucoadhesive gels. Full article

The aging of the existing reservoirs makes the hydrocarbon extraction shift toward newer reserves, and harsh conditioned carbonates, which possess high temperature and high salinity (HTHS). Conventional polymer-flooding fails in these HTHS carbonates, due to precipitation, viscosity loss, and polymer adsorption. Therefore, to counteract these challenges, novel polymer-based cEOR alternatives employ optimized polymers, polymer–surfactant, and alkali–surfactant–polymer solutions along with hybrid methods, which have shown a potential to target the residual or remaining oils in carbonates. Consequently, we investigate novel polymers, viz., ATBS, Scleroglucan, NVP-based polymers, and hydrophobic associative polymers, along with bio-polymers. These selected polymers have shown low shear sensitivity, low adsorption, and robust thermal/salinity tolerance. Additionally, adding an alkali-surfactant to polymer solution produces a synergy effect of improved mobility control, wettability alteration, and interfacial-tension reduction. Thus, enhancing the displacement and sweep efficiencies. Moreover, low-salinity water can precondition high-salinity reservoirs before polymer flooding (hybrid method), to decrease polymer adsorption and viscosity loss. Thus, this paper is a reference for novel polymers, and their hybrid techniques, to improve polymer-based cEOR field applications under HTHS conditions in carbonates. Additionally, the recommendations can assist in project designs with reasonable costs and minimal environmental impact. The implication of this work will aid in supplementing the oil and gas energy sector growth, making a positive contribution to the Middle Eastern economy. Full article

The subject of the study was emulsions based on enzymatically modified fats and stabilized with polysaccharides (xanthan gum and scleroglucan). Emulsion oil phases (blends of mutton tallow and hemp seed oil in a ratio of 3:1, 3:2, 3:3, 2:3 and 1:3) were characterized in the terms of acid value, melting point and mono- and diacylglycerols content before and after the modification. Emulsions containing modified fat blends and various amount (0.6, 0.8 and 1.0% w/w) of polysaccharides were investigated in the terms of their color, rheological properties, microstructure, droplet size and stability. The obtained results confirmed that enzymatic modification allowed to produce new fats, which can successfully be applied as an emulsion oil phases equipped with a sufficient amount of emulsifiers. The use of a variable amount of texture modifier in the proposed formulations did not show clear differences in the stability of the systems. Therefore, it does not seem justified to use greater amounts of a modifier (above 0.6% w/w) in this type of emulsions. The proposed formulations could be of interest to the cosmetics, food or pharmaceutical industry. Full article

Viscosity losses and high degradation factors have a drastic impact over hydrolyzed polyacrylamides (HPAM) currently injected, impacting the oil recovery negatively. Previous studies have demonstrated that biopolymers are promising candidates in EOR applications due to high thermochemical stability in harsh environments. However, the dynamic behavior of a biopolymer as scleroglucan through sandstone under specific conditions for a heavy oil field with low salinity and high temperature has not yet been reported. This work presents the rock–fluid evaluation of the scleroglucan (SG at 935 mgL⁻¹) and sulfonated polyacrylamide (ATBS at 2500 mgL⁻¹) to enhance oil recovery in high-temperature for heavy oils (212 °F and total dissolved solid of 3800 mgL⁻¹) in synthetic (0.5 Darcy) and representative rock samples (from 2 to 5 Darcy) for a study case of a Colombian heavy oilfield. Dynamic evaluation at reservoir conditions presents a scenario with stable injectivity after 53.6 PV with a minimal pressure differential (less than 20 psi), inaccessible porous volume (IPV) of 18%, dynamic adsorption of 49 µg/g, and resistance and residual resistance factors of 6.17 and 2.84, respectively. In addition, higher oil displacement efficiency (up to 10%) was obtained with lower concentration (2.7 times) compared to a sulfonated polyacrylamide polymer. Full article