Search Results (716)

Currently, the trade-off between oxygen permeation flux and structural stability in conventional perovskite oxides restricts the practical application of oxygen permeable membranes. In this study, a high-entropy design was applied to the B-site of BSCF matrix materials, resulting in the successful synthesis of a high-entropy perovskite, Ba_0.5Sr_0.5Co_0.71Fe_0.2Ta_0.03Ni_0.03Zr_0.03O_3−δ. The crystal structure, microstructure, and elemental composition of the material were systematically characterized and analyzed. Theoretical analysis and experimental characterization confirm that the material exhibits a stable single-phase high-entropy perovskite oxide structure. Under He as the sweep gas, the membrane achieved an oxygen permeation flux of 1.28 mL·cm⁻²·min⁻¹ and operated stably for over 100 h (1 mm thick, 900 °C). In a 20% CO₂/He atmosphere, the flux remained above 0.92 mL·cm⁻²·min⁻¹ for over 100 h, demonstrating good CO₂ tolerance. Notably, when the sweep gas is returned to the pure He atmosphere, the oxygen permeation flux fully recovers to 1.28 mL·cm⁻²·min⁻¹, with no evidence of leakage. These findings indicate that the proposed B-site doping strategy can break the trade-off between oxygen permeability and structural stability in conventional perovskite membranes. This advancement supports the industrialization of oxygen permeable membranes and offers valuable theoretical guidance for the design of high-performance perovskite materials. Full article

Recently, we have described SrMo_1-xMg_xO_3-δ perovskites (x = 0.1, 0.2) as excellent anode materials for solid oxide fuel cells (SOFCs), with mixed ionic and electronic conduction (MIEC) properties. After depositing on the solid electrolyte, they were annealed for sintering at high temperatures (typically 1000 °C), giving rise to oxidized scheelite-type phases, with SrMo_1-xMg_xO_4-δ (x = 0.1, 0.2) stoichiometry. To obtain the active perovskite phases, they were reduced again in the working anode conditions, under H₂ atmosphere. Therefore, there must be an excellent reversibility between the oxidized Sr(Mo, Mg)O_4-δ scheelite and the reduced Sr(Mo, Mg)O_3-δ perovskite phases. This work describes the topotactical oxidation, by annealing at 400 °C in air, of the SrMo_0.9Mg_0.1O_3-δ perovskite oxide. The characterization by X-ray diffraction (XRD) and neutron powder diffraction (NPD) was carried out in order to determine the crystal structure features. The scheelite oxides are tetragonal, space group I4₁/a (No. 88), whereas the perovskites are cubic, s.g. Pm-3m (No. 221). The Rietveld refinement of the scheelite phase from NPD data after annealing the perovskite at 400 °C and cooling it down slowly to RT evidences the absence of intermediate phases between perovskite and scheelite oxides, as well as the presence of oxygen vacancies in both oxidized and reduced phases, essential for their performance as MIEC oxides. The topotactical relationship between both crystal structures is discussed. Full article

In this study, a UVC photodetector (PD) was fabricated by incorporating CsI into a conventional double-cation perovskite (FAMAPbI₃) to enhance its stability. The device utilized a methylammonium iodide post-treatment solution to fabricate CsFAMAPbI₃ perovskite thin films, which functioned as the primary light-absorbing layer in an NIP structure composed of n-type SnO₂ and p-type spiro-OMeTAD. Perovskite films were fabricated and analyzed as a function of the Cs concentration to optimize the Cs content. The results demonstrated that Cs doping improved the crystallinity and phase stability of the films, leading to their enhanced electron mobility and photodetection performance. The UVC PD with an optimum Cs concentration exhibited a responsivity of 58.2 mA/W and a detectivity of 3.52 × 10¹⁴ Jones, representing an approximately 7% improvement over conventional structures. Full article

The construction sector presently consumes about 40% of global energy and generates 36% of CO₂ emissions, making facade retrofits a priority for decarbonising buildings. This review clarifies how ventilated facades (VFs), wall assemblies that interpose a ventilated air cavity between outer cladding and the insulated structure, address that challenge. First, the paper categorises VFs by structural configuration, ventilation strategy and functional control into four principal families: double-skin, rainscreen, hybrid/adaptive and active–passive systems, with further extensions such as BIPV, PCM and green-wall integrations that couple energy generation or storage with envelope performance. Heat-transfer analysis shows that the cavity interrupts conductive paths, promotes buoyancy- or wind-driven convection, and curtails radiative exchange. Key design parameters, including cavity depth, vent-area ratio, airflow velocity and surface emissivity, govern this balance, while hybrid ventilation offers the most excellent peak-load mitigation with modest energy input. A synthesis of simulation and field studies indicates that properly detailed VFs reduce envelope cooling loads by 20–55% across diverse climates and cut winter heating demand by 10–20% when vents are seasonally managed or coupled with heat-recovery devices. These thermal benefits translate into steadier interior surface temperatures, lower radiant asymmetry and fewer drafts, thereby expanding the hours occupants remain within comfort bands without mechanical conditioning. Climate-responsive guidance emerges in tropical and arid regions, favouring highly ventilated, low-absorptance cladding; temperate and continental zones gain from adaptive vents, movable insulation or PCM layers; multi-skin adaptive facades promise balanced year-round savings by re-configuring in real time. Overall, the review demonstrates that VFs constitute a versatile, passive-plus platform for low-carbon buildings, simultaneously enhancing energy efficiency, durability and indoor comfort. Future advances in smart controls, bio-based materials and integrated energy-recovery systems are poised to unlock further performance gains and accelerate the sector’s transition to net-zero. Emerging multifunctional materials such as phase-change composites, nanostructured coatings, and perovskite-integrated systems also show promise in enhancing facade adaptability and energy responsiveness. Full article

Lead-free (Bi_1/2Na_1/2)(Ti_1−x(Mg_1/3Nb_2/3)_x)O₃ ceramics were synthesized using the solid-phase method, and the effects of varying (Mg_1/3Nb_2/3)⁴⁺ content, substituting for Ti⁴⁺ ions at the B-site of the BNT perovskite lattice, on piezoelectric performance were systematically investigated. The influence of sintering temperature on both piezoelectric and ferroelectric properties was also explored, revealing that sintering temperature significantly affects both the microstructure and the electrical properties of the ceramics. The results indicate that the incorporation of (Mg_1/3Nb_2/3)⁴⁺ significantly enhances the piezoelectric and ferroelectric properties of BNT ceramics. Specifically, a maximum piezoelectric constant of 91 pC/N was achieved at a sintering temperature of 1160 °C and a doping concentration of x = 0.01. By comparing the ferroelectric properties across different doping levels and sintering temperatures, this study provides valuable insights for further design and process optimization of BNT-based piezoelectric materials. Full article

The structural and electrical properties of double perovskite compounds SrLaFe_1−xMn_xTiO_6−δ (x = 0, 0.33, 0.67, and 1.0) were studied using X-ray diffraction (XRD) and dielectric impedance measurements. The reparation of perovskite compounds was successfully achieved through the precursor solid-state reaction in air at 1250 °C. The purity phase and crystal structures of perovskite compounds were determined by means of the standard Rietveld refinement method using the FullProf suite. The best fitting results showed that SrLaFeTiO_6−δ was orthorhombic with space group Pnma, and both SrLaFe_0.67Mn_0.33TiO_6−δ and SrLaFe_0.33Mn_0.67TiO_6−δ were cubic structures with space group Fm3m, while SrLaMnTiO_6−δ was tetragonal with a I/4m space group. The charge density maps obtained for these structures indicated that the compounds show an ionic and mixed ionic–electronic conduction. The dielectric impedance measurements were carried out in the range of 20 Hz to 1 MHz, and the analysis showed that there is more than one relaxation mechanism of Debye type. Doping with Mn was found to reduce the dielectric impedance of the samples, and the major contribution to the dielectric impedance was established to change from a capacitive for SrLaFeTiO_6−δ to a resistive for SrLaMnTiO_6−δ. The fall in values of electrical resistance may be related to the possible occurrence of the double exchange (DEX) mechanism among the Mn ions, provided there is oxygen deficiency in the samples. DC-resistivity measurements revealed that SrLaFeTiO_6−δ was an insulator while SrLaMnTiO_6−δ was showing a semiconductor–metallic transition at ~250 K, which is in support of the DEX interaction. The dielectric impedance of SrLaFe_0.67Mn_0.33TiO_6−δ was found to be similar to that of (La,Sr)(Co,Fe)O_3-δ, the mixed ionic–electronic conductor (MIEC) model. The occurrence of a mixed ionic–electronic state in these compounds may qualify them to be used in free lead solar cells and energy storage technology. Full article

Understanding strain behavior near grain boundaries is critical for controlling structural distortions and oxygen vacancy migration in perovskite oxides. However, conventional techniques often lack the spatial resolution needed to analyze phase and domain evolution at the nanoscale. In this paper, polarization-dependent second-harmonic generation (SHG) imaging is employed as a tool to probe local symmetry breaking and complex domain structures in the vicinity of a low-angle grain boundary of SrTiO₃ (STO) bicrystals. We show that the anisotropic strain introduced by a tilted grain boundary produces strong local distortions, leading to the coexistence of tetragonal and rhombohedral domains. By analyzing SHG intensity and variations in the second-order nonlinear optical susceptibility, we map the distribution of strain fields and domain configurations near the boundary. In pristine samples, the grain boundary acts as a localized source of strain accumulation and symmetry breaking, while in samples subjected to intentional electrical stressing, the SHG response becomes broader and more uniform, suggesting strain relaxation. This work highlights SHG imaging as a powerful technique for visualizing grain-boundary-driven structural changes, with broad implications for the design of strain-engineered functional oxide devices. Full article

This study presents the successful fabrication of lead zirconate titanate (PZT) thin films on silicon (Si) substrates using a hybrid deposition method combining spin-coating and RF sputtering techniques. Initially, a PZT layer was deposited through four successive spin-coating cycles, followed by an additional layer formed via RF sputtering. The resulting multilayer structure was annealed at ${700 }^{°}$C for 2 h to improve crystallinity. Comprehensive material characterization was conducted using XRD, SEM, cross-sectional SEM, EDX, and UV–VIS absorbance spectroscopy. The analyses confirmed the formation of a well-crystallized perovskite phase, a uniform surface morphology, and an optical band gap of approximately 3.55 eV, supporting its suitability for sensing applications. Building upon these findings, a multilayer PZT-based touch sensor was fabricated and electrically characterized. Low-frequency I–V measurements demonstrated consistent and repeatable polarization behavior under cyclic loading conditions. In addition, $\left|Z\right|$–f measurements were performed to assess the sensor’s dynamic electrical behavior. Although expected dielectric responses were observed, the absence of distinct anti-resonance peaks suggested non-idealities linked to ${\mathrm{Ag}}^{+}$ ion diffusion from the electrode layers. To account for these effects, the classical Butterworth–Van Dyke (BVD) equivalent circuit model was extended with additional inductive and resistive components representing parasitic pathways. This modified model provided excellent agreement with the measured impedance and phase data, offering deeper insight into the interplay between material degradation and electrical performance. Overall, the developed sensor structure exhibits strong potential for use in piezoelectric sensing applications, particularly for tactile and pressure-based interfaces. Full article

This study focuses on the structural and electrochemical behavior of the compound ZnLaFeO₄ as a negative electrode material for nickel–metal hydride (Ni-MH) batteries. The material was synthesized by a sol–gel hydrothermal method to assess the influence of lanthanum doping on the ZnFe₂O₄ spinel structure. X-ray diffraction revealed the formation of a dominant LaFeO₃ perovskite phase, with ZnFe₂O₄ and La₂O₃ as secondary phases. SEM analysis showed agglomerated grains with an irregular morphology. Electrochemical characterization at room temperature and a discharge rate of C/10 (full charge in 10 h) revealed a maximum discharge capacity of 106 mAhg⁻¹. Although La³⁺ doping modified the microstructure and slowed the activation process, the electrode exhibited stable cycling with moderate polarization behavior. The decrease in capacity during cycling is due mainly to higher internal resistance. These results highlight the potential and limitations of La-doped spinel ferrites as alternative negative electrodes for Ni-MH systems. Full article

Materials with perovskite phases are widely used in solar cells and ferroelectric, piezoelectric, dielectric and superconducting devices due to their various notable functions. However, structural instability limits some compositions in forming robust perovskite phases for device applications. The analytical approach using the tolerance factor (t) can only guarantee prediction accuracy within a limited range, ascribed to its nature of overlooking the atomic interaction. Hence, here we establish a prediction model using formation energy as the target parameter for its reflection of the reaction of atoms and apply machine learning as the analysis method since it has been successfully employed in plenty of material property prediction studies. Machine learning employs statistical methodologies to identify correlative patterns within large-scale datasets, enabling accurate predictions with robust generalization. In this work, we built a model to predict the formation energy of ABX₃ perovskite using machine learning and achieved a model with an R-squared value of 0.928 and a root mean square error of 0.301 eV/atom, validated by first-principles computations. In total, 75% of the values were correctly predicted within an error lower than 0.06. This work could contribute to accelerating the study of solving perovskites’ instability. Full article

This study systematically investigates the magnetic ordering and magnetocaloric properties of a series of polycrystalline compounds, Gd_1-xDy_xScO₃ (x = 0, 0.1, 0.2 and 1). X-ray powder diffraction (XRD) analysis confirms that all samples exhibit an orthorhombic perovskite structure with a space group of Pbnm. The zero-field cooling and field cooling magnetization curves demonstrate a transition from antiferromagnetic to paramagnetic phases, with Néel temperatures of about 3 K for GdScO₃ and 4 K for DyScO₃. The doping of Dy³⁺ weakened long-range antiferromagnetic order and enhanced short-range magnetic disorder in GdScO₃, leading to vanished antiferromagnetic transition between 2 and 100 K for the sample of x = 0.2. Using the Arrott–Noakes equation, we constructed Arrott plots to analyze the system’s critical behavior. Both the compounds with x = 0.1 and x = 0.2 conform to the 3D-Heisenberg model. These results indicate the weakened long-range antiferromagnetic order induced by Dy³⁺ doping. Significant maximal magnetic entropy change (−Δ$S_{\mathrm{M}}^{\mathrm{M}\mathrm{a}\mathrm{x}}$) of 36.03 J/kg K at 3 K for the sample Gd_0.9Dy_0.1ScO₃ is achieved as the magnetic field changes from 0 to 50 kOe, which is higher than that of GdScO₃ (−Δ$S_{\mathrm{M}}^{\mathrm{M}\mathrm{a}\mathrm{x}}$ = 34.32 J/kg K) and DyScO₃ (−Δ$S_{\mathrm{M}}^{\mathrm{M}\mathrm{a}\mathrm{x}}$ = 15.63 J/kg K). The considerable magnetocaloric effects (MCEs) suggest that these compounds can be used in the development of low-temperature magnetic refrigeration materials. Full article

In this study, we investigated the formation mechanism of organo-metal halide perovskite nanostructures through a two-step process categorized as dissolution–recrystallization. It is proposed that the initial formation of nanostructures is governed by the generation of seed grains, whereas the Ostwald ripening model explains only the subsequent growth stage of these structures. We suggest that newly generated grains—formed adjacent to pre-positioned grains—experience compressive stress arising from volume expansion during the phase transition from PbI₂ to the MAPbI₃ perovskite phase. Owing to their unstable state, these grains may serve as effective seeds for the nucleation and growth of nanostructures. Depending on the dipping time, diverse morphologies such as nanorods, plates, and cuboids were observed. The morphology, including the aspect ratio and growth direction of these nanostructures, appears to be strongly influenced by the residual compressive stress within the seed grains. These findings suggest that the shape and aspect ratio of perovskite nanostructures can be tailored by carefully regulating nucleation, dissolution, and growth dynamics during the two-step process. Full article

Cobalt-based perovskite oxides exhibit remarkable catalytic activity owing to abundant oxygen vacancies and mixed ionic–electronic conductivity, but they suffer from structural instability. In contrast, iron-based perovskite oxides are thermochemically stable under oxidizing and reducing conditions but are catalytically limited. To combine these complementary properties, a composite perovskite oxide was designed and prepared by infiltrating Sr_0.95Ce_0.05CoO_3−δ (SCC) into Ba_0.5Sr_0.5Fe_0.8Cu_0.2O_3−δ (BSFC). The SCC precursor solution was dropwise applied to a BSFC|SDC|BSFC symmetric cell and heat treated. Surface morphology and compositional analyses confirmed the distribution of SCC nanoparticles on the BSFC surface. High-temperature X-ray diffraction and Rietveld refinement results revealed that both BSFC and SCC retained the cubic perovskite structure (space group Pm-3m) at room temperature. No phase transition or secondary phase formation was observed during heating from 200 to 800 °C, and the peak shifts are attributed to thermal expansion and possible oxygen loss at elevated temperatures. Upon cooling, the diffraction patterns returned to their initial state, confirming a high-temperature structural stability. XPS analysis showed an increase in the satellite peak intensity associated with Fe³⁺ after SCC infiltration, and the average oxidation state of Fe decreased from 3.52 (BSFC) to 3.49 (composite perovskite oxide). The O 1s spectra revealed a higher relative content of surface-adsorbed oxygen species in the composite, indicating increased oxygen vacancy formation. Full article

In the quest for stable, lead-reduced perovskites, this study unravels the structural and electronic evolution of CsZnI₃ across its α, β, and γ phases. DFT calculations spotlight the tetrahedral γ phase—with elongated Zn–I bonds (3.17 Å)—as the most stable, sidestepping the octahedral distortions of its metallic α and β counterparts. Pb²⁺ doping (>50%) drives a transformation to mixed octahedral–tetrahedral coordination, slashing the wide 3.15 eV bandgap to a solar-optimal 2.20 eV via lattice shrinkage. Above 50% doping, an optimum emerges—balancing structural integrity with efficient light absorption. These findings elevate Zn-doped or Zn-Pb-based compounds as promising and tunable perovskites for next-gen photovoltaics. Full article

In this study, BiBaO₃ perovskite was successfully synthesized via the sol–gel method and thoroughly characterized to evaluate its structural, microstructural, dielectric, electrical, and magnetic properties. X-ray diffraction (XRD) confirmed the formation of a single-phase perovskite structure with high crystallinity. Scanning electron microscopy (SEM) coupled with energy-dispersive X-ray spectroscopy (EDX) revealed a uniform grain morphology and elemental composition consistent with the intended stoichiometry. Dielectric measurements exhibited strong frequency-dependent behavior, suggesting potential for capacitive applications. The electrical conductivity displayed thermally activated behavior, indicative of semiconducting characteristics. Magnetic measurements showed weak ferromagnetic behavior at room temperature, an unusual observation for undoped BaBiO₃-based systems. This magnetism may stem from subtle structural distortions or compositional variations introduced during synthesis. Comparison with previously reported studies underscores the significant influence of the synthesis route and microstructural features on the multifunctional properties of BiBaO₃. Overall, the results highlight the promise of sol–gel-derived BiBaO₃ as a candidate for multifunctional electronic and magnetic applications. Full article