Search Results (1,878)

The global reliance on coal-fired power generation continues to produce vast quantities of fly ash, exceeding 500 million tons annually, with limited recycling rates. Given its high silica (SiO₂) and alumina (Al₂O₃) contents, fly ash represents a promising alternative raw material for sustainable refractory production. In this study, four aluminosilicate refractory castables were formulated using bauxite, calcined flint clay, kyanite, calcium aluminate cement, and microsilica, in which the fine fraction of flint clay was partially replaced by 0, 5, 10, and 15 wt.% fly ash. The specimens were dried at 120 °C and sintered at 850, 1050, and 1400 °C for 4 h. Their physical and mechanical properties were systematically evaluated, while phase evolution and microstructural development were analyzed through X-ray diffraction (XRD) and scanning electron microscopy (SEM). The results revealed that the incorporation of 10 wt.% fly ash (10FAC) provided the optimal balance between densification and strength, achieving compressive strengths of 45.0 MPa and 65.3 MPa after sintering at 1050 °C and 1400 °C, respectively. This improvement is attributed to the formation of a SiO₂-rich liquid phase derived from fly ash impurities, which promoted the in-situ crystallization of acicular secondary mullite and enhanced interparticle bonding among corundum grains. The 10FAC castable also exhibited only a slight increase in apparent porosity (26.39%) compared with the reference (25.74%), indicating effective sintering without excessive vitrification. Overall, the study demonstrates the technical viability of using fly ash as a sustainable substitute for flint clay in refractory castables. The findings contribute to advancing circular economy principles by promoting industrial waste valorization and resource conservation, offering a low-carbon pathway for the development of high-performance refractory materials for structural and thermal applications in energy-intensive industries. Full article

Hybrid PV-TEG systems can harvest both solar electrical and thermoelectric power, but their operating point drifts with irradiance, temperature gradients, partial shading, and load changes—often yielding multi-peak P-V characteristics. Conventional MPPT (e.g., P&O) and fixed-structure integer-order PID struggle to remain fast, stable, and globally optimal in these conditions. To address fast, robust tracking in these conditions, we propose an adaptive fractional-order PID (FOPID) MPPT whose parameters (K_p, K_i, K_d, λ, μ) are auto-tuned by the red-billed blue magpie optimizer (RBBMO). RBBMO is used offline to set the controller’s search ranges and weighting; the adaptive law then refines the gains online from the measured ΔV, ΔI slope error to maximize the hybrid PV-TEG output. The method is validated in MATLAB R2024b/Simulink 2024b, on a boost-converter–interfaced PV-TEG using five testbeds: (i) start-up/search, (ii) stepwise irradiance, (iii) partial shading with multiple local peaks, (iv) load steps, and (v) field-measured irradiance/temperature from Shanxi Province for spring/summer/autumn/winter. Compared with AOS, PSO, MFO, SSA, GHO, RSA, AOA, and P&O, the proposed tracker is consistently the fastest and most energy-efficient: 0.06 s to reach 95% MPP and 0.12 s settling at start-up with 1950 W·s harvested (vs. 1910 W·s AOS, 1880 W·s PSO, 200 W·s P&O). Under stepwise irradiance, it delivers 0.95–0.98 kJ at t = 1 s and under partial shading, 1.95–2.00 kJ, both with ±1% steady ripple. Daily field energies reach 0.88 × 10⁻³, 2.95 × 10⁻³, 2.90 × 10⁻³, 1.55 × 10⁻³ kWh in spring–winter, outperforming the best baselines by 3–10% and P&O by 20–30%. Robustness tests show only 2.74% power derating across 0–40 °C and low variability (Δv^max typically ≤ 1–1.5%), confirming rapid, low-ripple tracking with superior energy yield. Finally, the RBBMO-tuned adaptive FOPID offers a superior efficiency–stability trade-off and robust GMPP tracking across all five cases, with modest computational overhead. Full article

The growing generation of solid waste, driven by urbanization and industrialization, represents one of today’s greatest environmental challenges. The construction industry can play a key role in this scenario by incorporating recycling and waste reuse practices. Glass, a fully recyclable material, is still largely disposed of in landfills. A promising alternative is the use of ground glass in cementitious materials, partially or completely replacing cement or aggregates. Thus, in this paper, the effect of partially replacing Portland cement with ground glass of different colors including green, blue, transparent, amber, and colorful (all colors used mixed) in proportions of 15 and 35% in mortars was evaluated. The ground glasses were characterized by laser granulometry and chemical analysis. The properties of the mortars were then evaluated in the fresh and hardened state (apparent specific gravity, mechanical strength, water absorption, and open porosity). Regarding workability, the highest improvement observed was 6.8% for the 35% colored glass series compared to the reference series. In terms of entrapped air, there was an increase of up to 18.8% in the 35% green glass series. At 28 days of hydration, the 15% colored glass series obtained a 33% increase in flexural strength compared to the REF series. In the microstructure, it was found that a 15% glass presence was sufficient to reduce the portlandite index from 16.04 to 13.53, while a 35% glass presence was sufficient to reduce it to 7.51% portlandite, equivalent to a 54% reduction, suggesting significant potential for the reaction of the finer glass fractions with portlandite. This study suggests that the use of glass waste in a cementitious matrix can provide an environmentally appropriate alternative for recycling this material, contributing to a sustainable application and increased recycling rates of glass waste. Full article

In this paper, we study a class of time–space fractional partial differential equations involving Caputo time-fractional derivatives and Riesz space-fractional derivatives. A computational scheme is developed by combining a discrete approximation for the Caputo derivative in time with a modified trapezoidal method (MTM) for the Riesz derivative in space. We establish the stability and convergence of the scheme and provide detailed error analysis. The novelty of this work lies in the construction of an MTM-based spatial discretization that achieves ${\displaystyle \beta }$-order convergence in space and a ${\displaystyle (3-\alpha )}$-order convergence in time, while improving accuracy and efficiency compared to existing methods. Numerical experiments are carried out to validate the theoretical findings, confirm the stability of the proposed algorithm under perturbations, and demonstrate its superiority over a recent scheme from the literature. Full article

Aquafaba, a legume cooking water typically discarded as waste, represents a sustainable and plant-based protein source with promising functional applications. In this study, aquafaba hydrolysates were produced by enzymatic treatment with flavourzyme and savinase, yielding two products with distinct degrees of hydrolysis (DH: ~10% and ~29%). Aquafaba hydrolysates obtained using flavourzyme (AFHs) and savinase (ASHs), together with aquafaba isolate (AI), were incorporated into muffin cakes as partial flour substitutes (5%). The addition of hydrolysates significantly influenced cake quality parameters, particularly antioxidant capacity and textural attributes. Enzymatic hydrolysis, particularly with savinase, produced the most pronounced functional improvements. Technologically, ASHs supplementation significantly enhanced cake expansion, with specific volume values (2.23 mL/g) nearly doubling compared to the control (1.04 mL/g). Crust color was markedly altered, with L* decreasing and a* and b* rising, reflecting darker, more browned surfaces due to intensified Maillard reactions. Both ABTS and DPPH assays demonstrated increased radical scavenging activity with higher DH, while SDS-PAGE confirmed the release of smaller peptide fractions. The ABTS radical scavenging activity of the control muffin (CM, 262.53 mg TE/100 g) significantly increased in AIM (muffin cake substituted with aquafaba protein isolate, 481.87 mg TE/100 g) and reached its highest values in muffins containing AFHs (489.74 mg TE/100 g) and ASHs (530.56 mg TE/100 g), respectively. Hardness, a critical quality parameter particularly relevant to storage stability, decreased in hydrolysate-enriched samples compared with both control and isolate formulations. Oxitest results showed that extended induction periods for hydrolysate-containing cakes (18:47 h) were longer relative to control muffins (15:08 h). Thermal analysis also indicated improved thermal stability in the presence of aquafaba. Overall, the findings demonstrate that aquafaba hydrolysates can be effectively utilized in bakery systems to enhance antioxidant activity, oxidative stability, and technological properties, while simultaneously contributing to sustainable food valorization. Full article

The increasing demand for sustainable construction materials has prompted the recycling of construction and demolition waste in concrete manufacturing. This study investigates the feasibility of utilizing porcelain and brick waste as partial substitutes for natural sand in concrete with the objective of improving sustainability and preserving mechanical and durability characteristics. The experimental program was conducted in three consecutive phases. During the initial phase, natural sand was partially substituted with porcelain waste powder (PWP) and brick waste powder (BWP) in proportions of 25%, 50%, and 75% of the weight of the fine aggregate. During the second phase, polypropylene fibers were mixed at a dosage of 0.5% by volume fraction to enhance tensile and flexural properties. During the third phase, zinc oxide nanoparticles (ZnO-NPs) were utilized as a partial substitute for cement at concentrations of 0.5% and 1% to improve microstructure and strength progression. Concrete samples were tested at curing durations of 7, 28, and 91 days. The assessed qualities encompassed workability, density, water absorption, porosity, compressive strength, flexural strength, and splitting tensile strength. Microstructural characterization was conducted utilizing X-ray diffraction (XRD), scanning electron microscopy (SEM), and energy-dispersive X-ray spectroscopy (EDS). The findings indicated that porcelain waste powder markedly surpassed brick waste powder in all mechanical and durability-related characteristics, particularly at 25% and 50% sand replacement ratios. The integration of polypropylene fibers enhanced fracture resistance and ductility. Moreover, the incorporation of zinc oxide nanoparticles improved hydration, optimized the pore structure, and resulted in significant enhancements in compressive and tensile strength throughout prolonged curing durations. The best results were obtained with a mix of 50% porcelain sand aggregate, 1% zinc oxide nanoparticles as cement replacement, and 0.5% polypropylene fibers, for which the improvements in compressive strength, flexural strength, and splitting tensile strength were 39.5%, 46.2%, and 60%, respectively, at 28 days. The results confirm the feasibility of using porcelain and brick waste as sand replacements in concrete, as well as polypropylene fiber-reinforced concrete and polypropylene fiber-reinforced concrete mixed with zinc oxide nanoparticles as a sustainable option for construction purposes. Full article

In this study, the exhaust particulates of a diesel engine burning methanol/F-T diesel blends were collected. The nanostructure and oxidation reactivity of the particulates were explored using the Brunauer–Emmett–Teller (BET) method, high-resolution transmission electron microscope (HRTEM), and thermogravimetric analysis (TGA), and the relationship between them was assessed via the partial least squares (PLS) and variable importance in the projection (PLS-VIP). The results showed that particulates from methanol/F-T diesel combustion were aggregates composed of several primary particles, and the distribution range of particulate half pore width ($R$) was 8~76 nm. As the methanol mixture ratio increased, the mean $R$ of particulates decreased, and the particulates′ total pore volume ($V_p$), specific surface area ($S_{BET}$), and the fractal dimension ($D_f$) increased. Compared with F-T diesel, methanol/F-T diesel blends particulates showed more disordered structure with a smaller diameter ($d_p$) of primary particles, a shorter fringe length ($L_a$), a wider separation distance ($d$), and a larger tortuosity ($T_f$). With increasing the methanol mixture ratio, it was also found that the amount of soluble organic fraction (SOF) of particulates increased, while oxidation characteristic temperature and the apparent activation energy ($E_a$) reduced. The correlation coefficients of $E_a$ with $T_f$ and $D_f$ were 0.99 and 0.98, respectively, by the linear fitting, illustrating that they showed the strongest linear relationship with the reactivity among the discussed nanostructure parameters. The VIP values of $D_f$, $T_f$, $V_p$, and d, with $E_a$ obtained by the PLS and PLS-VIP, were greater than 1, indicating that they were the chief factors influencing particulate reactivity. Full article

The ability to predict the vapor pressure and vapor-phase composition of hydrocarbon mixtures (such as jet fuel, sustainable aviation fuel or its un-refined precursors) and partially vaporized hydrocarbon mixtures is important to simulations of processes that involve vaporization such as distillations, flash points, combustion properties of partially vaporized fuels, etc. Raoult’s Law provides a simple algebraic formula relating liquid composition and temperature to vapor composition and pressure. However, Raoult’s Law is not accurate at low mole fractions, which is typical for complex mixtures such as fuels. A common approach to correcting Raoult’s Law is to apply a scale factor, a so-called activity coefficient. Numerous models exist for predicting activity coefficients. Here we benchmark against the UNIFAC model, which predicts activity coefficients based on mole fractions, group fractions, Van der Waals volume and surface area and temperature-dependent interaction terms between groups. While this approach is truly predictive, its accuracy at very low mole fractions has not been validated, and it is computationally intensive, particularly for simulations (especially optimizations) that require vapor composition or pressure within the inner-most loop. Here we present an alternative correction to Raoult’s law, where the vapor pressure of the i^th component is represented by a modified form of the Clausius–Clapeyron equation. The reference temperature ($T_{ref}$) is replaced by a simple algebraic function that converges to $T_{ref}$ as $x_i$ approaches 1 while smoothly increasing from this value as $x_i$ decreases. Simultaneously, the heat of vaporization ($\mathsf{\Delta }{H}_{vap,i}\left(T\right)$) term is replaced by another simple algebraic expression that converges to $\mathsf{\Delta }{H}_{vap,i}\left(T\right)$ as $x_i$ approaches 1 while smoothly decreasing as $x_i$ decreases. In this model, the temperature-dependent heat of vaporization is tuned at each temperature such that the Clausius–Clapeyron equation reproduces the correct vapor pressure of the neat material, while the parameterized algebraic corrections are tuned to vapor pressure data of mixtures involving n-pentane, toluene, and dodecane, where the mole fractions of n-pentane and toluene are maintained below 10%_mol. Validation of the resulting model is accomplished by comparing modeled vapor–liquid equilibrium systems with experimental measurements. This approach improves the accuracy and computational efficiency of volatility predictions, thereby supporting the development, certification, and adoption of sustainable aviation fuel. Full article

Background/Objectives: Sepsis-induced cholestasis is caused by the release of inflammatory cytokines from lipopolysaccharide (LPS), a component of Gram-negative bacteria. No established therapy exists for this condition. We ascertained the anticholestatic potential of obeticholic acid (OCA), a potent FXR agonist, in a rat model of LPS-induced cholestasis. Methods: Male Wistar rats were randomized into Control, OCA (20 mg/kg/day, i.p., 6 days), LPS (total dose of 6.5 mg/kg, i.p., in the last 2 days, respectively), and OCA + LPS groups. Then, we assessed the serum cholestasis marker, alkaline phosphatase (ALP), and taurocholate-stimulated bile salt output. mRNA/protein levels of the main apical and sinusoidal uptake and efflux carriers were assessed by either or both RT-qPCR and Western blot. Bsep and Mrp2 localization was assessed by immunohistochemistry followed by confocal microscopy and image analysis. Inflammatory cytokines were measured in serum by ELISA. Results: OCA significantly attenuates inflammatory cytokine release and normalizes serum ALP in LPS-treated rats. OCA also increased the biliary output of the Bsep substrate, taurocholate, and partially improved total Bsep at both mRNA and protein levels. Furthermore, OCA fully normalizes Bsep in the canalicular plasma membrane fraction, suggesting improved membrane localization, a finding further confirmed by confocal microscopy. OCA sustained the beneficial downregulation of uptake transporters Ntcp and Oatp2 or the upregulation of the efflux pump Mrp3, both of which serve to minimize hepatocellular bile-salt accumulation. Conclusions: OCA prevents bile-salt accumulation in LPS-induced cholestasis by enhancing Bsep expression and localization, and by mitigating inflammation. This makes OCA a promising therapeutic candidate for sepsis-induced cholestasis. Full article

Aerosol–cloud interaction remains one of the largest sources of uncertainty in weather and climate modeling. This study investigates the impacts of aerosols on the macro- and microphysical properties of different cloud types over East Asia, based on nine years of joint satellite observations from CloudSat, CALIPSO, and MODIS, combined with ERA5 reanalysis data. Results reveal pronounced cloud-type dependence in aerosol effects on cloud fraction, cloud top height, and cloud thickness. Aerosols enhance the development of convective clouds while suppressing the vertical extent of stable stratiform clouds. For ice-phase structures, ice cloud fraction and ice water path significantly increase with aerosol optical depth (AOD) in deep convective and high-level clouds, whereas mid- to low-level clouds exhibit reduced ice crystal effective radius and ice water content, indicating an “ice crystal suppression effect.” Even after controlling for 14 meteorological variables, partial correlations between AOD and cloud properties remain significant, suggesting a degree of aerosol influence independent of meteorological conditions. Humidity and wind speed at different altitudes are identified as key modulating factors. These findings highlight the importance of accounting for cloud-type differences, moisture conditions, and dynamic processes when assessing aerosol–cloud–climate interactions and provide observational insights to improve the parameterization of aerosol indirect effects in climate models. Full article

Bioavailable phosphorus is essential for sustaining high crop productivity, yet excessive inorganic P fertilization often leads to P accumulation in stable soil forms, reducing utilization efficiency. Straw serves as an organic P source and enhances P availability by stimulating microbial activity. However, systematic studies on how organic P inputs (straw returning) and inorganic P fertilizers regulate soil bioavailable P through microbial and enzymatic processes remain limited. A 16-year field experiment was carried out in a rice–wheat rotation system, including five fertilization treatments: no fertilization (CK), optimized fertilization (OPT), increased N (OPTN), increased P (OPTP), and optimized fertilization combined with straw mulching/returning (OPTM). This study evaluates the impacts of long-term organic and inorganic P sources on soil P fractions, extracellular enzyme activities, and the composition of microbial communities, alongside their collective contributions to crop yield. In this study, based on soil samples collected in 2023, we found that fertilization led to significant increases in Citrate-P and HCl-P, enhanced the activities of β-1,4-glucosidase (BG), β-D-cellobiosidase (CBH), and β-1,4-N-acetylglucosaminidase (NAG), and altered both microbial diversity and co-occurrence network complexity. The OPTM treatment showed the highest yield and improved microbial diversity and network complexity, with Enzyme-P, Citrate-P, and HCl-P increasing by 62.64%, 11.24%, and 9.49%, and BG, CBH, and NAG activities rising by 22.74%, 40.90%, and 18.09% compared to OPT. Mantel tests and random forest analyses revealed significant associations between microbial community and biochemical properties, while partial least squares path modeling (PLS-PM) indicated that inorganic P source enhanced yield primarily through altering soil P dynamics and enzymatic processes, while microbial communities under organic P source acted as key mediators to increase crop productivity. These findings deepen insights into how microbial communities and enzymatic stoichiometry synergistically regulate phosphorus bioavailability and wheat yield, providing a theoretical basis for sustainable fertilization practices in rice–wheat rotation systems. Full article

Background: Chronic inflammatory skin disorders, including atopic dermatitis, psoriasis, acne, and chronic wounds, affect nearly two billion people worldwide, impose substantial morbidity and economic burden, and remain only partially controlled by existing therapies. The cutaneous endocannabinoid system (ECS), comprising cannabinoid receptors, endocannabinoids, and their metabolic enzymes, regulates inflammation, pruritus, barrier integrity, and tissue repair; cannabinoid receptor type 2 (CB₂) has emerged as a particularly relevant target. β-Caryophyllene (BCP), a dietary sesquiterpene and highly selective CB₂ agonist with favorable safety and pharmacokinetic attributes, has attracted attention as a promising topical candidate. Methods: We systematically searched PubMed, Embase, and Web of Science (inception–30 July 2025) for studies on “β-caryophyllene” and dermatological outcomes, prioritizing purified BCP and analytically characterized BCP-rich fractions. Quantitative parameters, including tested concentration ranges (0.5 µM–10%) and principal mechanistic outcomes, were extracted to provide a translational context. Results: BCP penetrates the stratum corneum, suppresses NF-κB/MAPK and IL-4/TSLP pathways, enhances Nrf2-driven antioxidant defenses, and accelerates re-epithelialization and collagen remodeling. Across in vitro, in vivo, and formulation studies, BCP produced consistent anti-inflammatory and barrier-restorative effects within this concentration range. CB₂ antagonism attenuated these responses, confirming receptor specificity. BCP’s volatility and autoxidation to β-caryophyllene oxide (BCPO) necessitate stability-by-design strategies using antioxidants, low-oxygen processing, and protective packaging. Human evidence, limited to BCP-rich botanicals such as Copaifera oleoresins, suggests benefits for scars, wounds, and acne but lacks compound-specific validation. Conclusions: BCP exhibits coherent CB₂-mediated anti-inflammatory, antipruritic, antioxidant, and reparative actions with a favorable safety profile. Dose-defined, oxidation-controlled clinical trials of purified BCP are warranted to establish its potential as a steroid-sparing topical therapy. Full article

This study examines binary blends of three types of polyhydroxyalkanoates (PHAs)—poly(3-hydroxybutyrate) (PHB), poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) (PHBH), and poly(3-hydroxybutyrate-co-4-hydroxybutyrate) (P3HB4HB)—with a focus on their rheological, thermal, and mechanical behavior. The blends exhibit partial miscibility in both the melt and solid states. Glass transition analysis revealed that semicrystalline/amorphous PHA combinations are fully miscible (single Tg) at amorphous PHA contents below 30 wt%. Above this threshold, a two-phase morphology develops, consisting of crystalline spherulites embedded in an amorphous matrix. When the amorphous PHA content reached ≥30 wt%, the blends could be oriented by stretching, yielding materials that display thermoplastic elastomer (TPE)-like behavior without chemical modification of the base polymers. Thermal and mechanical characterization, supported by X-ray diffraction of samples before and after orientation, confirmed that the elastomeric properties originate from the multiphase architecture formed by crystalline and amorphous domains interconnected through a miscible amorphous fraction. Full article

Exercise-unacclimatized dromedary camels regularly perform strenuous work in desert heat; however, their short-term hematologic and biochemical recovery is not well defined. In this prospective repeated-measures experiment, seven healthy bulls underwent a standardized 90 min outdoor exercise bout, with blood sampled before exercise and at 0, 3, 6, 24, and 48 h of recovery. The analytical panel included hematology, primary hemostasis, electrolytes, osmolality, protein fractions, metabolites, and serum enzymes. Red-cell indices remained stable, indicating minimal erythrocyte mobilization, while bleeding time shortened sharply at 0 h and normalized by 3 h. Sodium and osmolality followed a biphasic pattern with an early rise at 3 h, a nadir at 6 h, and partial rebound by 24 h, whereas potassium and phosphate stayed depressed from 6 to 48 h. Proteins and glucose showed transient changes, and muscle-associated enzymes, especially lactate dehydrogenase, peaked early before declining. These findings demonstrate that camels tolerate combined exercise and heat stress but require up to 48 h to re-establish biochemical balance. The recovery timeline provides a clinically relevant framework for sampling, welfare monitoring, and management of work–rest cycles in desert environments. Full article

Biochar shows potential for regulating nitrogen cycling in cold-region soils, but the roles of its different fractions during freeze-thaw cycles (FTCs) remain unclear. To elucidate the regulation of cold-region soil environments by biochar at the fraction scale, we examined the effects of biochar and its fractions (dissolved and undissolved) on soil nitrogen forms and microbial communities under simulated FTCs. The experiment included a constant-temperature control, a freeze–thaw control, and three biochar treatments with pristine biochar (PBC), dissolved biochar fraction (DBC), and undissolved biochar fraction (UBC), respectively, maintained in triplicate at five FTC frequencies (0, 1, 5, 10, and 20). Changes in soil physicochemical properties and nitrogen forms were measured at five FTC frequencies, and microbial community composition was analyzed by high-throughput sequencing after the 20th cycle. Both biochar fractions reduced inorganic nitrogen, with ammonium nitrogen decline resulting from joint action and nitrate nitrogen (NO₃⁻-N) reduction dominated by UBC. PBC alleviated microbial biomass nitrogen stress by relying primarily on its undissolved fraction to enhance soil water retention, organic carbon, and total nitrogen. Redundancy analysis indicated that total nitrogen and NO₃⁻-N were the key factors affecting microbial community composition. Partial least squares structural equation modeling results suggested that soil physicochemical properties influenced microbial community structure characteristics more strongly than nutrient properties. These findings provide a new perspective on the regulatory mechanism of biochar on the agricultural soil environment in cold regions. Full article