Search Results (26)

Phenolic antioxidants such as tert-butylhydroquinone (TBHQ) can prolong the shelf life of edible oils by delaying the oxidation process. The excessive use of TBHQ can damage food quality and public health, so it is necessary to develop an efficient TBHQ detection technique. In this work, nickel-aluminum double hydroxide (NiAl-LDH) was grown on glucose carbon spheres (GC), which formed porous carbon nanomaterials (named NiAl-LDH@GC-800) after pyrolysis at 800 °C. The successful synthesis of the material was verified by scanning electron microscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The obtained NiAl-LDH@GC-800 was dopped onto a glass carbon electrode to prepare an electrochemical sensor for TBHQ. The synergistic effect of porous carbon and Ni metal reduced from NiAl-LDH by high-temperature calcination accelerated the electron transfer rate and improved the sensitivity of the sensor. The prepared sensor showed a low limit of detection (LOD) of 8.2 nM, a high sensitivity (4.2 A·M⁻¹), and a good linear range (20~300 µM) in detecting TBHQ. The sensor was also successfully used for TBHQ detection in edible oils, including chili oil, peanut oil, and rapeseed oil. Full article

This article reports a simple hydrothermal method for synthesizing nickel disulfide (NiS₂) on the surface of fluorine-doped tin oxide (FTO) glass, followed by the deposition of 5 nm Au nanoparticles on the electrode surface by physical vapor deposition. This process ensures the uniform distribution of Au nanoparticles on the NiS₂ surface to enhance its conductivity. Finally, an Au@NiS₂-FTO electrochemical biosensor is obtained for the detection of dopamine (DA). The composite material is characterized using transmission electron microscopy (TEM), UV-Vis spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The electrochemical properties of the sensor are investigated using cyclic voltammetry (CV), differential pulse voltammetry (DPV), and time current curves in a 0.1 M PBS solution (pH = 7.3). In the detection of DA, Au@NiS₂-FTO exhibits a wide linear detection range (0.1~1000 μM), low detection limit (1 nM), and fast response time (0.1 s). After the addition of interfering substances, such as glucose, L-ascorbic acid, uric acid, CaCl₂, NaCl, and KCl, the electrode potential remains relatively unchanged, demonstrating its strong anti-interference capability. It also demonstrates strong sensitivity and reproducibility. The obtained Au@NiS₂-FTO provides a simple and easy-to-operate example for constructing nanometer catalysts with enzyme-like properties. These results provide a promising method utilizing Au coating to enhance the conductivity of transition metal sulfides. Full article

The review paper provides a comprehensive analysis of nickel oxide (NiO) as an emerging material in environmental monitoring by surveying recent developments primarily within the last three years and reports the growth processing and strategies employed to enhance NiO sensing performance. It covers synthesis methods for pristine NiO, including vapor-phase, liquid-phase, and solution-processing techniques, highlighting advantages and limitations. The growth mechanisms of NiO nanostructures are explored, with a focus on the most recent research studies. Additionally, different strategies to improve the gas sensing performance of NiO are discussed (i.e., surface functionalization by metallic nanoparticles, heterostructure formation, carbon-based nanomaterials, and conducting polymers). The influence of these strategies on selectivity, sensitivity, response time, and stability of NiO-based sensors is thoroughly examined. Finally, the challenges and future directions that may lead to the successful development of highly efficient NiO-based gas sensors for environmental monitoring are introduced in this review. Full article

Nickel-based alloys that contain chromium are widely used in corrosion-resistant applications in industry, but they are sensitive to the environment when the passive chromium oxide layer is damaged. In Ni600 and Ni625 alloys, precipitates can deplete the surface layer of chromium oxide. To better characterize and analyze the nickel alloy surfaces and their chromium carbides, chemical etching with different etchants and electrolytic etching were applied to sample surfaces. This paper revealed their efficacy in etching various carbides within the nickel alloys, and orange phases ranging from 2 to 20 μm in optical micrographs were identified as titanium-containing compounds. Carbides located on the grain boundaries were determined to be Cr23C6 and were surrounded by chromium-depleted zones. The findings and figures in this paper provide a more intuitive reference for future analysis of carbides and titanium nitrides, enhancing the understanding of their impact on the corrosion resistance of these alloys, which will not only contribute to the material science field but also aid in developing the Ni-based alloys for industrial applications. Full article

Xylene gas is highly toxic, can irritate the skin, and is also very harmful to the body. Therefore, it is necessary to prepare sensors that can accurately detect xylene. In this paper, NiTiO₃ nanoparticles were synthesized by the hydrothermal method and used to modify NiO, and a NiTiO₃-modified NiO (NiTiO₃-NiO) nanosheet material was successfully prepared. Its microstructure and internal composition were observed and analyzed by various characterization methods. When detecting 100 ppm xylene gas at the optimum temperature, comparing the response level of the NiTiO₃-NiO sensor with that of a pure nickel oxide sensor, the former was 20 times that of the latter, and the sensitivity was greatly improved. In a 100 ppm xylene gas environment, the response level of the sensor reached 21, the minimum detection limit was 1 ppm, and the recovery time was 135.75 s. NiTiO₃ is a perovskite-structured material, with many active sites and good catalytic properties that promote redox reactions. Full article

To determine urea accurately in clinical samples, food samples, dairy products, and agricultural samples, a new analytical method is required, and non-enzymatic methods are preferred due to their low cost and ease of use. In this study, bitter gourd peel biomass waste is utilized to modify and structurally transform nickel oxide (NiO) nanostructures during the low-temperature aqueous chemical growth method. As a result of the high concentration of phytochemicals, the surface was highly sensitive to urea oxidation under alkaline conditions of 0.1 M NaOH. We investigated the structure and shape of NiO nanostructures using powder X-ray diffraction (XRD) and scanning electron microscopy (SEM). In spite of their flake-like morphology and excellent crystal quality, NiO nanostructures exhibited cubic phases. An investigation of the effects of bitter gourd juice demonstrated that a large volume of juice produced thin flakes measuring 100 to 200 nanometers in diameter. We are able to detect urea concentrations between 1–9 mM with a detection limit of 0.02 mM using our urea sensor. Additionally, the stability, reproducibility, repeatability, and selectivity of the sensor were examined. A variety of real samples, including milk, blood, urine, wheat flour, and curd, were used to test the non-enzymatic urea sensors. These real samples demonstrated the potential of the electrode device for measuring urea in a routine manner. It is noteworthy that bitter gourd contains phytochemicals that are capable of altering surfaces and activating catalytic reactions. In this way, new materials can be developed for a wide range of applications, including biomedicine, energy production, and environmental protection. Full article

A metal-free porphyrazine derivative with peripheral phthalimide substituents was metallated with a nickel(II) ion. The purity of the nickel macrocycle was confirmed using HPLC, and characterized by MS, UV–VIS, and 1D (¹H, ¹³C) and 2D (¹H–¹³C HSQC, ¹H–¹³C HMBC, ¹H–¹H COSY) NMR techniques. The novel porphyrazine was combined with various carbon nanomaterials, such as carbon nanotubes—single walled (SWCNTs) and multi-walled (MWCNTs), and electrochemically reduced graphene oxide (rGO), to create hybrid electroactive electrode materials. The carbon nanomaterials’ effect on the electrocatalytic properties of nickel(II) cations was compared. As a result, an extensive electrochemical characterization of the synthesized metallated porphyrazine derivative on various carbon nanostructures was carried out using cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS). An electrode modified with carbon nanomaterials GC/MWCNTs, GC/SWCNTs, or GC/rGO, respectively, was shown to have a lower overpotential than a bare glassy carbon electrode (GC), allowing for the measurement of hydrogen peroxide in neutral conditions (pH 7.4). It was shown that among the tested carbon nanomaterials, the modified electrode GC/MWCNTs/Pz3 exhibited the best electrocatalytic properties in the direction of hydrogen peroxide oxidation/reduction. The prepared sensor was determined to enable a linear response to H₂O₂ in concentrations ranging between 20–1200 µM with the detection limit of 18.57 µM and sensitivity of 14.18 µA mM⁻¹ cm⁻². As a result of this research, the sensors produced here may find use in biomedical and environmental applications. Full article

In this study, two alternative synthesis routes have been used in obtaining gas-sensitive NiO materials. The structural and morphological aspects were systematically investigated by X-ray diffraction (XRD) and transmission electron microscopy (TEM), revealing significant differences further mirrored in their sensing performances. Simultaneous electrical resistance and contact potential differences have been involved aiming to decouple the energetic contributions: work function (ΔΦ), surface band bending (qΔVs) and electron affinity (Δχ). Two sensing mechanism scenarios explained the enhancement and downgrading in the sensor response to carbon monoxide (CO) concerning the synthesis strategies. The role of relative humidity (RH) was considered throughout the electrical operando (in-field) investigations. Full article

The results of the synthesis of PAN/NiO composite fibers by the electrospinning method are presented. The electrospinning installation included a rotating drum collector for collecting fibers. Nickel oxide nanoparticles were synthesized by solution combustion synthesis from nickel nitrate and urea. It was shown that monophase NiO nanoparticles with average particle sizes of 154 nm could be synthesized by this method. NiO nanoparticles were investigated by X-ray diffraction analysis and scanning electron microscopy. Based on NiO nanoparticles, composite PAN/NiO fibers were obtained by electrospinning. The obtained composite fibers were modified with heat treatment (stabilization and carbonization) processes. Obtained C/NiO fibers were investigated by SEM, and EDAX. It was shown that obtained composite fibers could be used for the detection of acetone and acetylene in air. These results show that C/NiO based electrospun fibers have potential applications in gas sensors. Full article

Perovskite solar cells (PSCs) and dye-sensitized solar cells (DSCs) both represent promising strategies for the sustainable conversion of sunlight into electricity and fuels. However, a few flaws of current devices hinder the large-scale establishment of such technologies. On one hand, PSCs suffer from instabilities and undesired phenomena mostly linked to the perovskite/hole transport layer (HTL) interface. Most of the currently employed organic HTL (e.g., Spiro-OMeTAD) are supposed to contribute to the perovskite decomposition and to be responsible for charge recombination processes and polarization barriers. On the other hand, power conversion efficiencies (PCEs) of DSCs are still too low to compete with other conversion technologies. Tandem cells are built by assembling p-type and n-type DSCs in a cascade architecture and, since each dye absorbs on a different portion of the solar spectrum, the harvesting window is increased and the theoretical efficiency limit for a single chromophore (i.e., the Shockley–Queisser limit) is overcome. However, such a strategy is hindered by the lack of a p-type semiconductor with optimal photocathode features. Nickel oxide has been, by far, the first-choice inorganic p-type semiconductor for both PV technologies, but its toxicity and non-optimal features (e.g., too low open circuit voltage and the presence of trap states) call for alternatives. Herein, we study of three p-type semiconductors as possible alternative to NiO, namely CuI, CuSCN and Cu₂O. To this aim, we compare the structural and electronic features of the three materials by means of a unified theoretical approach based on the state-of-the art density functional theory (DFT). We focus on the calculation of their valence band edge energies and compare such values with those of two widely employed photo-absorbers, i.e., methylammonium lead iodide (MAPI) and the triple cation MAFACsPbBrI in PSCs and P1 and Y123 dyes in DSCs, given that the band alignment and the energy offset are crucial for the charge transport at the interfaces and have direct implications on the final efficiency. We dissect the effect a copper vacancy (i.e., intrinsic p-type doping) on the alignment pattern and rationalize it from both a structural and an electronic perspective. Our data show how defects can represent a crucial degree of freedom to control the driving force for hole injection in these devices. Full article

Cold spray is an emerging additive manufacturing process that allows particles to be coated onto the surface of a base material without melting. It is suitable to repair components made from temperature-sensitive materials, such as grey cast iron, which cannot be easily restored using conventional methods like welding or thermal spray. In this study, the nickel-based alloy Inconel 625 was successfully coated onto a grey cast iron (GJL250) using a cold spray process, and extensive experiments were carried out to study the effects of diffusion between the coating and the substrate after heat treatment at 400, 600, 850 and 1050 °C for 3 and 6 hours durations. The coatings in all conditions were dense (0.25% to 3%) and had defect-free interfaces. Under heat treatment, the diffusion layer increased in thickness with increasing temperature and duration due to atomic diffusion. The Inconel 625 coating is also shown to be effective against oxide growth as compared to grey cast iron. The hardness of the coatings is also stable at high temperatures. The heat-treated coatings at 600 °C achieved a peak hardness of around 500 HV, which is 30% and 60% higher than the as-sprayed coating and grey cast iron substrate, respectively, because of the possible formation of recrystallized nanostructured grains and strengthening precipitates. These findings demonstrate the potential application of using cold spray on nickel-based alloy coatings for restoration and surface enhancement of grey cast iron components, such as engine blocks and pump housings. Full article

This work describes a straightforward method using one-step preparation of graphene/nickel nanocomposite materials from low-cost materials including graphene oxide and nickel metal. Repetitive CVs lead to the simultaneous deposition of metallic nickel nanoparticles and reduced graphene oxide sheets onto glassy carbon electrode. The obtained nanocomposite-modified surfaces were characterised by cyclic voltammetry, differential pulse voltammetry and field emission scanning electron microscopy. The result demonstrated the ability to produce nickel nanoparticles with a small size of about 20 nm, uniformly dispersed on a graphene oxide matrix. The ERGO-NiNP nanocomposite could be used as a sensor material exhibiting high performance; it is used here in order to detect Sunset Yellow (SY) and for quantification in complex media. The sensor enables rapid quantification of SY with a good linearity (R² = 0.996) in the range of 10–1000 nM, together with a low detection limit of 3.7 nM (equivalent to 1.7 µg L⁻¹) and a high sensitivity up to 7 µA/µM. The sensor also displays high reliability with a RSD value = 1.08 (n = 10) and good reusability (signal response variation below 5% after 5 detection/cleaning cycles). Finally, we demonstrate how this GCE/ERGO-NiNP sensor can be used for the successful determination of SY in commercial soft drink samples with an acceptable deviation below 6.4% when compared to HPLC method. Full article

Nanocomposite sensors were prepared using carbon soot (CNPs), nickel oxide nanoparticles (NiO-NPs), and cellulose acetate (CA), which was used to detect and study the sensing mechanism of mesitylene vapour at room temperature. Synthesised materials were characterised using high-resolution transmission electron microscopy (HR-TEM), powder x-ray diffraction (PXRD), Raman spectroscopy, and nitrogen sorption at 77 K. Various sensors were prepared using individual nanomaterials (NiO-NPs, CNPs, and CA), binary combinations of the nanomaterials (CNPs-NiO, CNPs-CA, and NiO-CA), and ternary composites (NiO-CNPs-CA). Among all of the prepared and tested sensors, the ternary nanocomposites (NiO-CNPs-CA) were found to be the most sensitive for the detection of mesitylene, with acceptable response recovery times. Fourier-transform infrared (FTIR) spectroscopy coupled with an LCR meter revealed that the mesitylene decomposes into carbon dioxide. Full article

Approaches are being developed to create composite materials with a fractal-percolation structure based on intercalated porous matrices to increase the sensitivity of adsorption gas sensors. Porous silicon, nickel-containing porous silicon, and zinc oxide have been synthesized as materials for such structures. Using the impedance spectroscopy method, it has been shown that the obtained materials demonstrate high sensitivity to organic solvent vapors and can be used in gas sensors. A model is proposed that explains the high sensitivity and inductive nature of the impedance at low frequencies, considering the structural features and fractal-percolation properties of the obtained oxide materials. Full article

In this paper, we report on the development of a highly sensitive and humidity-tolerant metal-oxide-based volatile organic compound (VOC) sensor, capable of rapidly detecting low concentrations of VOCs. For this, we successfully fabricated two different thicknesses of nickel oxide (NiO) sensors using a spin-coating technique and tested them with seven different common VOCs at 40% r.h. The measured film thickness of the spin-coated NiO was ~5 μm (S-5) and ~10 μm (S-10). The fastest response and recovery times for all VOCs were less than 80 s and 120 s, respectively. The highest response (R_g/R_a = 1.5 for 5 ppm ethanol) was observed at 350 °C for both sensors. Sensors were also tested in two different humidity conditions (40% and 90% r.h.). The humidity did not significantly influence the observed sensitivity of the films. Furthermore, S-10 NiO showed only a 3% drift in the baseline resistance between the two humidity conditions, making our sensor humidity-tolerant compared to traditional n-type sensors. Thus, we propose thick-film NiO (10 μm) sensing material as an interesting alternative VOC sensor that is fast and humidity-tolerant. Full article