Search Results (249)

This study evaluated the efficacy of various cleaning protocols on two nickel–titanium (NiTi) file systems—RaCe EVO(RE) and EdgeFile X7(EE)—using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Eighty-four NiTi files (42RE, 42EE) were divided into seven groups (n = 12), including a group with unused, sterilized files and a group of used files without cleaning. The remaining files were subjected to simulated clinical use, followed by different cleaning methods, such as soaking in sodium hypochlorite (NaOCl), ethanol wiping (with or without magnification), enzymatic spray, and enzymatic solution. SEM images were imported into ImageJ to quantify surface changes, while EDX assessed elemental composition. The p-value was set to ≤0.05 for significance. Apart from the unused files, calcium and phosphorus—indicators of dentin debris—were present in all groups, especially those cleaned with enzymatic spray (p ≤ 0.0001). Their percentage in RE files soaked in NaOCl or wiped with ethanol was statistically lower than the positive control (p ≤ 0.0001). Post-use, all files showed significantly higher surface asymmetry in Groups 2 and 6 (p = 0.001). Cleaning efficacy depends on the type of NiTi file. RE files responded well to both wiping and soaking, while EE required soaking for effective debris removal. Enzymatic spray was ineffective. Full article

Titanium dioxide (TiO₂), a widely used semiconductor in photocatalysis owing to its adequate potential for water hydrolysis, chemical stability, low toxicity, and low cost. However, its efficiency is limited by fast charge-carrier recombination and poor visible light absorption. Coupling TiO₂ with a p-type semiconductor, such as nickel oxide (NiO), forming a p-n heterojunction, decreases the recombination of charge carriers and increases photocatalytic activity. In this work, the surface of TiO₂ modified with NiO nanoparticles (NPs) induced by radiolysis for photocatalytic hydrogen production was studied. The photocatalytic activity of NiO/TiO₂ was evaluated using methanol as a hole scavenger under UV–visible light. All modified samples presented superior photocatalytic activity compared to bare TiO₂. The dynamics of the charge carriers, a key electronic phenomenon in photocatalysis, was investigated by time-resolved microwave conductivity (TRMC). The results highlight the crucial role of Ni-based NPs modification in enhancing the separation of the charge carrier and activity under UV–visible irradiation. Furthermore, the results revealed that under visible irradiation, NiO-NPs inject electrons into the conduction band of titanium dioxide. Full article

Resistance spot welding was performed to join a 2 mm thick TA2 titanium plate and Q235 steel plate using nickel foil with thicknesses of 0.02 mm, 0.04 mm, and 0.06 mm as interlayers. The microstructure of the nugget zone and the interface region of the joint were systematically observed and analyzed, and the tensile shear-bearing capacity of the joint was evaluated. As the welding current increased, the tensile shear load of the joint exhibited a trend of initially increasing and subsequently decreasing. When the welding current was 8 kA, the tensile shear load of the joints with an interlayer of 0.04 mm thickness reached a maximum value of 8.02 kN. The results indicate that employing a reduced welding current can effectively prevent the mixing of nuggets on both sides of the titanium and steel interface. This ensures that the intermetallic compounds formed in the interface region are confined to the Ti-Ni series, which is crucial for enhancing the tensile shear load of the joint. Full article

In this study, a TiNi alloy with a composition of 50 at.% of titanium and 50 at.% of nickel is investigated in terms of its corrosion and biocompatibility behavior for biomedical applications. The corrosion measurements, which include the determination of open-circuit potential and linear polarization resistance measurements, cyclic polarization measurements, and electrochemical impedance spectroscopy in 9 g L⁻¹ NaCl, show that TiNi has satisfactory corrosion stability. According to the SEM and EDS analysis, after cyclic polarization, pitting corrosion occurred, accompanied by the dissolution of the unstable Ti₂Ni inclusions. The analysis also showed that TiNi has good biocompatibility for human osteoblast-like cells, as determined by the mitochondrial activity, which was assessed using a direct contact test following ISO standard 10993-5, via scanning electron microscopy (SEM) and fluorescent microscopy. Full article

This paper presents the results of a study of the catalytic hydrogenation of phenanthrene using catalysts based on chrysotile modified with nickel and titanium (chrysotile/NiTi), as well as coal shale. Complex characterization of catalysts in terms of acid, texture and morphological properties was carried out. Pre-reduction in the catalysts has been found to increase the yield of partially and fully hydrogenated products, including tetrahydronaphthalene, trans-decalin and dihydrophenanthrene. Particular attention is paid to the role of coal shale as a donor source of hydrogen in thermolysis conditions. The results of hydrogenation revealed complex mechanisms of phenanthrene transformations, including partial saturation of aromatic rings, desulfurization and the formation of alkyl-substituted compounds. The obtained data emphasize the prospects of using the studied catalysts in the processes of processing heavy and solid hydrocarbon raw materials, which opens up opportunities for creating new technologies for the production of liquid fuel. Full article

Fluoride mouthwashes are often recommended by dental professionals due to their proven benefits for oral hygiene. However, it is vital to acknowledge that these products may have undesirable effects on orthodontic treatment outcomes, particularly by altering the biomechanical properties of orthodontic devices and their components. To gain a comprehensive understanding of this potential issue, an extensive and systematic search was conducted across seven distinct databases. PRISMA extension for scoping reviews (PRISMA ScR) guidelines were followed. Following a detailed evaluation and careful scrutiny of the available evidence, a total of seven relevant studies met the inclusion criteria and were incorporated into the current scoping review. Findings indicated that regular intraoral use of fluoride-containing mouthwashes could lead to heightened corrosion and greater release of metal ions from stainless-steel brackets and nickel–titanium (NiTi) archwires. Additionally, the mechanical properties and structural integrity of titanium–molybdenum alloy (TMA) wires were negatively influenced by exposure to fluoride mouthwashes. Although existing evidence highlights these potential drawbacks, there remains a clear necessity for additional comprehensive research. Given the possibility that fluoride mouthwashes could adversely influence orthodontic treatment effectiveness, orthodontists and dental clinicians must exercise cautious judgment and deliberate consideration when prescribing fluoride-based mouthwashes for patients undergoing orthodontic therapy. Full article

The miniaturization of smart materials has become a new trend in the modern manufacturing industry due to its enormous application in the aerospace, biomedical, and automobile sectors. Nickel–titanium (NiTi)-based binary shape memory alloys (SMAs) are one of the smart materials with certain supreme features like shape memory effect, pseudo-elasticity, high ductility, strong corrosion-resistance, and elevated wear resistance. For this, several micro-machining processes have been developed to machine NiTi SMAs. This paper summarizes all of the conventional and non-conventional micro-machining processes employed to machine NiTi SMAs. In this review process, the surface integrity, dimensional accuracy of the machined surface, cutting force and tool wear analysis during conventional and non-conventional micro-machining of NiTi SMA are evaluated mostly with the aid of input process variables like cutting speed, depth of cut, width of cut, types of coolants, tool coating, discharge voltage, capacitance, laser fluence, pulse duration, scan speed, electrolysis concentration and gap voltage. The optimization of process parameters using different methods during conventional and non-conventional micro-machining of NiTi SMAs is also analyzed. The problems faced during conventional micro-machining of NiTi SMAs are overcome by non-conventional micro-machining processes as discussed. The present study aims to recognize potential developments in the improvement of the micro-machinability of NiTi SMAs. Full article

Prior to the laser processing, the surface of the TiC-reinforced particles underwent a metallization process with Ni-P, with the objective of enhancing the wettability between the TiC and the Ti6Al4V, thereby ensuring enhanced wear resistance of the titanium-based composite (TMC) coatings. In this study, the chemical deposition method was utilized to synthesize three types of metallized TiC with varying phosphorus contents. The P contents of these samples were determined to be 9.12 wt.% (HP metallized TiC), 6.55 wt.% (MP metallized TiC), and 1.71 wt.% (LP metallized TiC). It was observed that the thickness of the coatings increased in a gradual manner with the decrease in P. Furthermore, the coating of the LP metallized TiC was found to possess the highest degree of crystallinity and a microcrystalline structure. The 50 wt.% TiC-Ti6Al4V composite coatings (TMC-Nickel-free, TMC-HP, TMC-MP, and TMC-LP) were produced by laser fusion deposition using untreated TiC and three metallized TiC enhancements. The findings indicate that TMC-LP exhibits cracking only during the initial processing stage. Surface metallization has been shown to enhance the wear resistance of composite coatings through several mechanisms, including increased bonding of the ceramic phase to the metal matrix and the formation of hard Ti₂Ni compounds. The wear rates of TMC-HP, TMC-MP, and TMC-LP were reduced by 22%, 43%, and 72%, respectively, in comparison to TMC-Nickel-free. Full article

Nickel–titanium carbide (Ni-TiC) coatings were synthesized on Q235 steel via double-pulse electrodeposition to enhance surface properties. The influence of TiC concentration on surface morphology, microstructure, and performance was systematically studied using SEM, TEM, XRD, microhardness testing, wear analysis, and electrochemical methods. At low TiC concentrations (2–4 g/L), the coatings exhibited typical cell-like morphology. At 8 g/L, the coating showed a dense structure, refined grains, and broad Ni diffraction peaks. TEM analysis revealed nickel and TiC grain sizes of 97.82 nm and 34.75 nm, respectively. The plating rate remained stable (~36.94 mg·cm⁻²·h⁻¹), while surface roughness increased with TiC content. The 8 g/L TiC coating achieved the highest microhardness (743.13 HV), lowest wear loss (5.43%), and superior corrosion resistance, with a self-corrosion current density of 5.27 × 10⁻⁶ A·cm⁻² and polarization resistance of 7705.62 Ω·cm². These enhancements are attributed to uniform TiC dispersion and grain boundary pinning. Thus, 8 g/L TiC is optimal for fabricating Ni-TiC coatings with improved mechanical and electrochemical performance. This work demonstrates a practical strategy for developing high-performance Ni-based composite coatings via double-pulse electrodeposition. Full article

A novel parameter optimization method for additively manufacturing nickel–titanium (NiTi) alloys using laser powder bed fusion (LBPF) was developed. Compared with the conventional NiTi alloy and the previously reported LPBF-NiTi alloy, the LBPF-NiTi alloy prepared with these parameters exhibits excellent tensile properties and an anisotropic microstructure. Since distinct regions of orthopedic implants have specific functional requirements, we investigated the anisotropy of this LPBF-NiTi in terms of its osteoinductive capacity to determine the appropriate building direction for prosthesis fabrication. The biosafety of the transverse (XY-NiTi) and longitudinal (XZ-NiTi) planes was assessed through cytotoxicity assays. Comparative analyses of the biological activities of these planes were conducted by evaluating the adherent cell counts, the adhesion morphology, and the expression of osteogenic-related genes and factors in adherent cells. Compared with XZ-NiTi, XY-NiTi exhibited superior cell adhesion properties. Additionally, the expression levels of osteogenic markers (RUNX2, ALP, OPG, and OCN) were significantly greater in bone marrow mesenchymal cells (BMMCs) adhered to XY-NiTi than in those adhered to XZ-NiTi. These results indicate a greater osteogenic potential in the XY-NiTi group. XY-NiTi was more advantageous as an implant–bone contact surface. Building implant products in the direction perpendicular to the load-bearing axis enhances biofixation; thus, this is the preferred orientation for manufacturing orthopedic implants. Full article

Nickel-containing orthodontic archwires, particularly those made of nickel-titanium (NiTi) and stainless steel (SS), play a crucial role in orthodontic treatment using the fixed technique due to their mechanical properties. However, concerns regarding nickel-induced allergic reactions, cytotoxicity, and metal ion release, especially nickel-related ones, persist. This narrative review aims to explore recent findings on nickel release from orthodontic appliances, building upon prior systematic reviews by analyzing both in vitro and in vivo studies under various environmental conditions. The databases Web of Science, Scopus, and PubMed were searched for relevant studies that examined the relationship between nickel ion release from nickel-containing archwires and various environmental conditions. The studies found indicate that while metal ion release occurs during short-term treatment, the levels are lower than harmful thresholds, with factors such as pH, corrosion, length of treatment, and environmental influences affecting release rates. Despite this, long-term studies are few and are usually conducted only in an in vitro or in vivo environment, but not both. To establish causal relationships regarding metal ion release, in vivo monitoring of ions like Ni is critical, with further research needed to assess its prolonged effects. Furthermore, collaborative efforts among practitioners, researchers, and regulatory bodies are vital for developing evidence-based guidelines for orthodontic material selection, prioritizing patient safety and addressing metal ion release risks. Full article

In the context of Al-Kharj city, which is steadily advancing as an industrial and manufacturing hub within Saudi Arabia, this study has significant relevance. The city’s focus on metal forming, fabrication, and materials engineering makes it crucial to optimize processes such as hot deformation of metallic alloys for various sectors, including aerospace, automotive, oil and gas, and structural applications. By assessing and comparing phenomenological and physical material models for nickel, aluminum, titanium, and iron-based alloys, this study aids Al-Kharj industries in advancing their process simulation and predictive performance. Thus, this study aims to evaluate the proposed phenomenological and physically based constitutive models for Ni-, Al-, Ti-, and Fe-based alloys to enhance the accuracy of high-temperature deformation simulations. Phenomenological models investigated include the Johnson–Cook (JC), Fields and Backofen (FB), and Khan–Huang–Liang (KHL) formulations, while the Zerilli–Armstrong (ZA) model represents the physical category. Additionally, various modifications to these models are explored. Model parameters are calibrated using the Levenberg–Marquardt algorithm to minimize mean square error. Performance is assessed through key statistical metrics, including the correlation coefficient (R), average absolute relative error (AARE), and root mean square error (RMSE). Of the 32 models analyzed, a modified version of the JC model delivers the highest accuracy across all alloys. Furthermore, four other modifications, one each for the JC and ZA models and two for the FB model, exhibit superior predictive capability for specific alloys. This makes this study valuable not just academically, but also as a practical resource to boost Al-Kharj’s industrial competitiveness and innovation capacity. Full article

Background and Objectives: Nickel–titanium (Niti) instruments have enhanced root canal cleaning in primary teeth, but file fractures are still common. Materials and Methods: This study evaluated the cyclic fatigue resistance of 120 Niti files from four different systems, A: Kedo SG (n = 30); B: Neoendo Pedoflex (n = 30); C: Pedoflex Waldent files (n = 30); and D: Vortex Blue files (n = 30). All the files had similar tip diameters (0.25 mm) and tapers (0.4%) and underwent heat treatment during manufacturing. Cyclic fatigue tests showed notable variations in cycles to fracture (NCF) across groups. All fracture surfaces of the files were assessed through scanning electron microscopy. Results: The mean values achieved in the experimental groups (A, B, C) were less than those in the control Group D (976.90 ± 1085.19). Files in Group A demonstrated the highest NCF (697.01 ± 420.09), while Pedoflex files in Group C showed the lowest values (203.88 ± 155.46). Statistical analysis using the Mann–Whitney test revealed significant differences between Group C and Groups A, B, and D and no differences among Groups A, B, and D. Conclusions: These findings suggest that Kedo SG and Neoendo Pedoflex files offer comparable cyclic fatigue resistance to Vortex Blue files. In contrast, Pedoflex Waldent files exhibit lower resistance to fracture. Full article

Three alloys differing in their nominal chemical composition (Ni₅₀Ti₅₀, Ni₅₁Ti₄₉, and Ni₅₂Ti₄₈) were produced in the form of powders using high-energy ball milling. Their microstructure, morphology, structure, and phase composition were studied using the X-ray diffraction technique, scanning, and transmission electron microscopy. For the detailed structural analysis, the Rietveld method was used. The results show that each of the alloys consists of three fractions: fine, medium, and thick. The fractions varied in particle/agglomerate size from 200 nm to 800 μm. Additionally, they varied in phase composition. The fine fraction comprised a mixture of amorphous and nanocrystalline phases. Additionally, the medium and coarse phases showed crystalline solid solutions formed on the bases of nickel or titanium, as well as a crystalline bcc phase—a precursor of the parent phase (B2). The largest contribution in the alloy powders, over 80%, comes from the amorphous–nanocrystalline mixture (ANM). The increase in the nickel content resulted in an increase in ANM quantity of 3 wt.%. Similarly, the weight content of the titanium-based solid solution increased to about 7 wt.%. In contrast, the quantity of the nickel-based solid solution decreased from 3 wt.% to approximately 1 wt.% in the Ni₅₀Ti₅₀ and Ni₅₂Ti₄₈ alloys. Full article

Nickel-doped titanium dioxide (NIT) with different nickel contents (0.1–1.0 wt%) was prepared via the sol–gel method, combined with mechanical ball milling. X-ray diffraction (XRD), scanning electron microscopy (SEM), and UV–Vis diffuse reflectance spectroscopy (DRS) were employed to characterize the crystalline structure, morphological characteristics, and optical properties of the samples. The photocatalytic activity was evaluated through the photocatalytic degradation of methylene blue (MB) under visible light and nitric oxide (NO) under simulated sunlight. The XRD results show that all the catalysts retain the anatase phase, confirming that nickel doping does not alter the crystalline structure of TiO₂. NIT catalysts exhibited a plate-like morphology due to the ball milling treatment of the precursors. The DRS analysis revealed that nickel modification induced a redshift in the absorption edge of TiO₂ and enhanced the visible-light absorption. The photocatalytic tests demonstrated that 0.5 wt% NIT and 0.7 wt% NIT exhibited the highest photocatalytic activity for MB degradation, achieving degradation rates of 93.1% and 91.4% after 60 min, respectively. Moreover, 0.7 wt% NIT showed the optimal NO conversion efficiency of 45.4% after 30 min. The improved photocatalytic performance of the sample is attributed to enhanced visible-light absorption, reduced charge recombination, and a high specific surface area. This study provides a facile strategy for synthesizing Ni-doped TiO₂ nanoplates based on the sol–gel method, which is scalable in regard to the industrial production of efficient photocatalysts. Full article