Search Results (489)

Nowadays, nanosized mesoporous oxides are of increasing interest to scientists. They can be used as components of heterogeneous catalysts, for photo- and electrocatalysis, as gas sensors, etc. For instance, the desired properties in catalysts include a nano size and homogeneity of the particles that form the catalyst. The particle sizes of oxides are set at the initial stage of their formation, as precursors of precipitation in the context of wet chemistry. The creation of optimal conditions is possible through the use of homogeneous precipitation, where the precipitant is formed within the solution itself as a result of a hydrolysis reaction. The resolution of this issue involved the utilization of urea in our experimental setup, obtaining the hydrolysis products of ammonia and carbon dioxide. Consequently, precipitation reactions can be utilized to obtain hydroxides, carbonates, or hydroxy carbonates of metals. The precursors were calcined, obtaining nanosized mesoporous oxides, which can have a wide range of applications. Nanosized 0.1–50 nm metal oxides were obtained, including those aluminum, iron, indium, zinc, nickel, and cobalt. Full article

Silver nanoparticles (AgNPs), iron oxide nanoparticles (Fe₂O₄NPs), and multiwalled carbon nanotubes (MWCNTs) are widely used in various applications, such as biomedicine, environmental remediation, and agriculture. In addition, these nanomaterials can affect the production of bioactive compounds in plants that have pharmacological activities. In the current study, the in vitro plant cultures of Chinese lobelia (Lobelia chinensis Lour.) were established in MS medium and treated with 0, 12.5, 25, 37.5, and 50 mg L⁻¹ AgNPs or Fe₂O₄NPs, or MWCNTs. Initially, plants were grown for four weeks without any elicitors, and after that, the cultures were treated with nano-elicitors for one week. After five weeks, the effects of nano-elicitors were estimated on growth, total phenolic, flavonoids, polyacetylenes, and ABTS/DPPH/FRAP antioxidant activity was investigated. The results showed that lower levels of AgNPs (25 mg L⁻¹), Fe₂O₄NPs (25 mg L⁻¹), and MWCNTs (12.5 mg L⁻¹) favored the accumulation of fresh and dry biomass. Whereas, 37.5 mg L⁻¹ AgNPs, 25 mg L⁻¹ Fe₂O₄NPs, and 37.5 mg L⁻¹ MWCNTs enhanced the accumulation of total phenolics, flavonoids, specific phenolic compounds including chlorogenic acid, catechin, phloretic acid, coumaric acid, salicylic acid, naringin, myricetin, linarin, and polyacetylenes viz. lobetylonin and lobetyolin in higher concentrations. The plant extracts elicited by nanomaterials also depicted very good antioxidant activities according to ABTS, DPPH, and FRAP assays. These results suggest that specific nanomaterials, and at specific levels, could be used for the production of bioactive compounds from shoot cultures of Chinese lobelia. Full article

The growing demand for low-emission maritime transport and efficient onboard energy management has intensified research into advanced control strategies for hybrid shipboard microgrids. These systems integrate both AC and DC power domains, incorporating renewable energy sources and battery storage to enhance fuel efficiency, reduce greenhouse gas emissions, and support operational flexibility. However, integrating renewable energy into shipboard microgrids introduces challenges, such as power fluctuations, varying line impedances, and disturbances caused by AC/DC load transitions, harmonics, and mismatches in demand and supply. These issues impact system stability and the seamless coordination of multiple distributed generators. To address these challenges, we proposed a hierarchical control strategy that supports sustainable operation by improving the voltage and frequency regulation under dynamic conditions, as demonstrated through both MATLAB/Simulink simulations and real-time hardware validation. Simulation results show that the proposed controller reduces the frequency deviation by up to 25.5% and power variation improved by 20.1% compared with conventional PI-based secondary control during load transition scenarios. Hardware implementation on the NVIDIA Jetson Nano confirms real-time feasibility, maintaining power and frequency tracking errors below 5% under dynamic loading. A comparative analysis of the classical PI and sliding mode control-based designs is conducted under various grid conditions, such as cold ironing mode of the shipboard microgrid, and load variations, considering both the AC and DC loads. The system stability and control law formulation are verified through simulations in MATLAB/SIMULINK and practical implementation. The experimental results demonstrate that the proposed secondary control architecture enhances the system robustness and ensures sustainable operation, making it a viable solution for modern shipboard microgrids transitioning towards green energy. Full article

This study introduces an advanced strategy for improving microbial fuel cell (MFC) performance in hexavalent chromium (Cr(VI)) wastewater treatment. A high-performance nano-iron sulfide (nano-FeS) hybridized biocathode was developed by regulating glucose concentration and applying an external voltage. The combination of a glucose concentration of 1000 mg/L and a 0.2 V applied voltage greatly promoted the in situ biosynthesis of nano-FeS, resulting in smaller particle sizes and increased quantities within the biocathode, leading to enhanced electrochemical performance. The MFC with the hybridized biocathode exhibited the highest power density (43.45 ± 1.69 mW/m²) and Cr(VI) removal rate (3.99 ± 0.09 mg/L·h), outperforming the control by 29% and 71%, respectively. The improvements were attributed to the following processes. (1) Nano-FeS provided additional active sites that enhanced electron transfer and electrocatalytic activity, reducing cathode passivation; (2) it protected microorganisms by reducing Cr(VI) toxicity, promoting redox-active substance enrichment and antioxidant enzyme secretion, which maintained microbial activity; (3) the biocathode selectively enriched electroactive and Cr(VI)-reducing bacteria (such as Brucella), fostering a stable and symbiotic microbial community. This study highlights the promising potential of regulating carbon source and external voltage to boost nano-FeS biosynthesis, offering a sustainable and efficient strategy for MFC-based Cr(VI) wastewater treatment with practical implications. Full article

Triple-negative breast cancer (TNBC) frequently evades immune recognition and elimination, resulting in an immunosuppressive microenvironment. The phagocytic activity of tumor-associated macrophages underscores the development of nanomaterials as a promising strategy to target these macrophages and modulate their polarization, thereby advancing immunotherapy against TNBC. This research developed functional polymers that are complexed with therapeutic molecules as a coating strategy for iron oxide nanoparticles. An arginine-based poly (ester urea urethane) polymer complexed with a macrophage-polarizing molecule (APU-R848) could provide a synergistic effect with iron oxide nanoparticles (IONPs) to stimulate the M1-polarization of macrophages at the tumor site, resulting in a versatile nano-platform for immune regulation of TNBC. In the 4T1 in vivo breast tumor model, the APU-R848-IONPs demonstrated an improved intratumoral biodistribution compared to IONPs without a polymer coating. APU-R848-IONPs significantly reversed the immune-suppressive tumor environment by reducing the M2/M1 macrophage phenotype ratio by 51%, associated with an elevated population of cytotoxic T cells and a significantly enhanced production of tumoricidal cytokines. The activated immune response induced by APU-R848-IONP resulted in a significant anti-tumor effect, demonstrating an efficacy that was more than 3.2-fold more efficient compared to the controls. These immune-regulatory pseudo-protein-coated iron oxide nanoparticles represent an effective nano-strategy for macrophages’ regulation and the activation of anti-tumor immunity, providing a new treatment modality for triple-negative breast cancer. Full article

In order to develop an efficient, environmentally friendly heavy metal ions adsorbent, the amino-modified expanded vermiculite-supported nano zero-valent iron (nZVI@PEI/EVMT) was prepared by using polyethyleneimine (PEI) as the functional reagent and expanded vermiculite (EVMT) as the carrier. The characterization results of nZVI@PEI/EVMT confirm that the PEI modification did not destroy the crystal configuration of EVMT, and when nano zero-valent iron (nZVI) was successfully loaded onto the PEI/EVMT surface, the value of saturation magnetic field was 41.5 emu/g, which could be separated from solution with magnet. The performance of Cr(VI) adsorption onto nZVI@PEI/EVMT was studied, showing that the ideal mass ratio for nZVI@PEI/EVMT was 1:1, and the removal capacity was largest when solution pH was 2. After four adsorption–desorption cycles, the adsorption amounts remained 40.1 mg/g. The Cr(VI) adsorption onto nZVI@PEI/EVMT was more consistent with a pseudo-second-order kinetics equation. Isotherm adsorption data accord with the Langmuir model, which suggests that the adsorption was the monolayer, the maximum adsorption amount was 116.2 mg/g at 30 °C and pH 2, and the adsorption was spontaneous and endothermic. It was inferred that the adsorption mechanisms included electrostatic attraction, reduction, chemical complexation, and co-precipitation. Full article

Synthetic dyes are commonly present in industrial wastewater and when discharged in water bodies without receiving a treatment capable of removing or destroying them, they turn into concerning water pollutants. These organic contaminants threaten living beings due to their toxicity, and some of them can even damage DNA. Consequently, in order to achieve sustainable development, it is necessary to develop eco-friendly tools that can efficiently manage this kind of pollution. In the present study the aqueous extract from the leaves of Leucaena leucocephala (an invasive plant species native to Mexico) was used to produce green nano zero-valent iron (nZVI). The nanomaterial was characterized (TEM, UV–vis, FTIR, SEM, EDS, XRD) and assayed regarding its antioxidant potential (DPPH test) and capacity to remediate the pollution caused by two dyes. It proved to be able to adsorb nigrosine (288.30 mg/g of nanomaterial) and tartrazine (342.50 mg/g of nanomaterial), and also displayed antioxidant activity (effective concentration to discolor 50% of the DPPH solution = 286.02 μg/mL). Therefore, the biogenic antioxidant nanoparticle proved also to be a possible nanotool to be applied to remediate water contamination caused by these synthetic dyes. Full article

The co-occurrence of the synthesis of a functionalized magnetic nano iron oxides–biochar composite (MFe@BC) via impregnation–thermal pyrolysis and its use to remove micro-sized poly (3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV) microplastics from simulated wastewater was demonstrated in this study. The results showed that PHBV removal efficiency correlated positively with MFe@BC dosage, achieving an adsorption capacity of 13.14 mg/g and a removal efficiency of 98.53% at an optimal dosage of 1.5 g/L. Adsorption kinetics fit a pseudo-second-order model (R² = 0.9999), and the isotherm followed the Langmuir model (R² = 0.8440), yielding a theoretical maximum capacity of 31.96 mg/g. Characterization indicated chemisorption-driven monolayer adsorption via surface complexation and hydrogen bonding. Magnetic nano-iron transfer from MFe@BC to the PHBV surface imparted magnetic properties to PHBV, enabling synergistic adsorption and magnetic separation. Removal efficiency remained above 95% across pH 4–9 and COD 0–500 mg/L. Regeneration experiments indicated that the MFe@BC showed robust reusability, maintaining >92% PHBV removal efficiency after four adsorption–regeneration cycles. The results of this study may provide a feasible pathway for PHBV microplastic removal from secondary effluent, indicating that MFe@BC prepared in this study can be used for the removal of PHBV microplastics in a wide range of water bodies. Full article

Polyethylene terephthalate (PET) microfibers in effluent are difficult to remove using technology. In this study, a novel nano-sized iron-oxide-loaded biochar (FBC) with robust magnetic response characteristics was prepared by the impregnation–pyrolysis method and used for the removal of PET microfibers in simulated wastewater. The results showed that the removal efficiency of FBC on PET exceeded 91.69% over a wide pH range (4~9) and was barely affected by co-existing COD (15~500 mg/L) at an initial PET concentration of 1 g/L and FBC dosage of 3 g/L. The adsorption kinetics and isotherms indicated that the adsorption was more consistent with the pseudo-second-order kinetics (PSO) model and the Langmuir model, suggesting that the adsorption involved both physical and chemical actions. In addition, the maximum PET adsorption capacity expected by the Langmuir model reached 4500 mg/g, confirming the high adsorption performance of FBC. The characterization of FBC before and after adsorption indicated that PET was adsorbed mainly by the formation of Fe–O–PET bonds, π-π interactions, and hydrogen bonding. In addition, the FBC maintained a high PET removal efficiency of over 95.59% after four consecutive regeneration cycles. This study provides new insights into the efficient removal of fibrous microplastics from wastewater. Full article

Conventional magnetorheological fluids (MRFs) exhibit a constrained shear strength that restricts their deployment in high-performance damping systems. This study introduces a dual-axis innovation strategy combining material science and device physics to fundamentally redefine MRF capabilities. We develop a hierarchical particle architecture through the controlled integration of micro/nano-sized carbonyl iron particles (CIPs), enhanced by polyethylene glycol/oleic acid surface engineering to optimize magnetic chain formation and interfacial bonding. The engineered MRF demonstrates a shear yield strength of 99.6 kPa at 0.757 T, surpassing conventional single-component MRFs by a significant margin. Integrated with a self-decoupling damper that isolates magnetic flux from mechanical motion, this synergistic design achieves exceptional force modulation: damping forces scale from 281.5 kN (5 mm stroke) to 300 kN (60 mm stroke), with current-regulated adjustability factors reaching 3.34. The system exhibits substantial improvements in both maximum damping force (93.9 kN enhancement) and energy dissipation efficiency compared to standard MRF dampers. Through co-optimization of the particle architecture and magnetic circuit design, this work establishes new performance benchmarks for smart fluid technology. The achieved force capacity and dynamic response characteristics directly address critical challenges in seismic engineering and industrial vibration control, where extreme load-bearing requirements demand simultaneous high strength and tunable damping capabilities. Full article

Severe plastic deformation and subsequent heat treatments yield nanostructured commercially pure (CP) titanium Grade 4 with average grain size of about 100 nm and exceptional strength. To elucidate the underlying strengthening mechanisms in this nanotitanium (nanoTi), this study uses atom probe tomography (APT) to analyze the atomic structure of grain boundaries and assess impurity segregation. Results reveal the formation of grain boundary segregations, primarily composed of iron (Fe) atoms, reaching concentrations up to 3.3 ± 0.2 at% in localized regions. The average width of these segregation layers is 6.13 ± 0.45 nm. The paper considers a mechanism for forming these segregations and discusses relevant theoretical models describing their contribution to the material’s enhanced strength. Full article

The dual-pole magnetic abrasive finishing (DMAF) method was proposed to achieve a smooth surface on TC4 titanium alloy. Firstly, both the distribution of the magnetic field and the intensity of magnetic induction produced by nine combinations of magnetic poles of different shapes were simulated using Ansys Maxwell software (2024R2). According to the results of the simulation, the optimal combination of magnetic poles was determined. Then, the machining parameters of multi-stage DMAF were optimized through comparative experiments on major single factors. Finally, combinations of the mixed magnetic abrasive in three polishing stages were obtained as follows: #100 electrolytic iron powder (Fe₃O₄) + #2000 white abrasive (WA), #200 Fe₃O₄ + #8000 WA, and #450Fe₃O₄ + #w1 diamond (DMD). The gap between the upper and lower magnetic poles was set to 5 mm, the rotational speed of the magnetic pole was set to 300 rpm, and the quality ratio of the abrasive was 2:1. The experiments indicated that the average surface roughness Ra was reduced from an initial value of 0.433 μm to 8 nm after 30 min of multi-stage DMAF, and a nano-level mirror polishing effect was essentially achieved in the polishing zone. Full article

This study aims to evaluate the corrosion behavior of ductile cast iron (FCD-500) under simulated marine engine operating conditions and to determine the optimal corrosion inhibitor conditions under chloride contamination. Experiments were conducted at 50 °C and 80 °C, with different Cl⁻ concentrations (0–500 ppm) and sodium nitrite (NaNO₂)-based inhibitor concentrations (0; 9000; 15,000; 17,000 ppm). Immersion and electrochemical tests were performed to analyze the microstructural corrosion characteristics and inhibitor efficiency. The results indicated that as the Cl⁻ concentration increased, proportionally higher levels of inhibitor were required to maintain surface stability. The maximum inhibition efficiency, approximately 97.3%, was achieved with an inhibitor concentration of 17,000 ppm, at a Cl⁻ concentration of 100 ppm. Full article

The accumulation of heavy metal cadmium (Cd) in farmland soil in edible parts of crops seriously threatens plant growth, human health, and even the global ecological environment. Finding stabilization remediation technology is an important means to treat Cd-contaminated soil. This study comprehensively evaluated the synergistic effects of independent or combined application of biochar (BC) (10, 30 g kg⁻¹) and nano zero-valent iron (nZVI) (0.1% w/w) on soil properties and morphological and physiological traits of pakchoi (Brassica rapa L. subsp. chinensis) under Cd (1, 3 mg kg⁻¹) stress by pot experiments. It was shown that Cd toxicity negatively affected soil properties, reduced pakchoi biomass and total chlorophyll content, and increased oxidative stress levels. On the contrary, the combined application of BC (30 g kg⁻¹) and nZVI (0.1%, w/w) reduced the Cd accumulation in the shoot parts of pakchoi from 0.78 mg·kg⁻¹ to 0.11 mg·kg⁻¹, which was lower than the Cd limit standard of leafy vegetables (0.20 mg kg⁻¹) in GB 2762-2017 “National Food Safety Standard”. Compared with the control, the treatment group achieved a 61.66% increase in biomass and a 105.56% increase in total chlorophyll content. At the same time, the activities of catalase (CAT) and superoxide dismutase (SOD) increased by 34.86% and 44.57%, respectively, and the content of malondialdehyde (MDA) decreased by 71.27%. In addition, the application of BC alone (30 g·kg⁻¹) increased the soil pH value by 0.43 units and the organic carbon (SOC) content by 37.82%. Overall, the synergistic effect of BC (30 g kg⁻¹) and nZVI (0.1% w/w) helped to restore soil homeostasis and inhibit the biotoxicity of Cd, which provided a new option for soil heavy metal remediation and crop toxicity mitigation. Full article

In this work, 1,3-diketone synthesized via the Claisen condensation method and nano-copper particles modified by the Brust–Schiffrin method were added into a commercial marine medium-speed diesel engine cylinder piston oil to evaluate their effects on boundary lubrication performance. Friction and wear tests conducted on CKS-coated piston ring and cast-iron cylinder liner samples demonstrated significant reductions in both friction and wear with the addition of 1,3-diketone and nano-copper particles. Compared to the original oil without additives, the friction force was reduced by up to 16.7%, while the wear of the piston ring and cylinder liner was decreased by up to 21.6% and 15.1% at 150 °C, respectively. A worn surface analysis indicated that the addition of 1,3-diketone and functionalized nano-copper particles influenced the depolymerization and tribo-chemical reactions of the anti-wear additive ZDDP (zinc dialkyldithiophosphate) in the original engine oil. This modification enhanced the oil’s anti-friction and anti-wear properties, offering valuable insights into the development of eco-friendly lubricants for energy-efficient systems. Full article