Search Results (91)

Biomineralized self-healing concrete is a type of concrete that, during its service life, induces the generation of calcium carbonate through the participation of microorganisms or active enzymes, thereby achieving self-repair of cracks at different times. Self-healing concrete based on biomineralization can achieve sustainable crack repair and could enhance the strength and extend the service life of buildings. This article comprehensively analyzes the latest progress in bio-self-healing concrete, including microbial-based self-healing, enzyme-induced calcium carbonate precipitation (EICP), microcapsule-loaded microbial in situ remediation, and bio-inorganic mineral synergist self-healing technology. The maximum repairable width of the crack is 2.0 mm, and concrete strength can be increased by 135%. These methods offer new insights and strategies for the repair of concrete cracks, providing fundamental knowledge for the later application of intelligent engineering of bio-self-healing concrete and the analysis of micro-interface mechanisms. At the same time, they clarify the practical possibility of microbial technology in building materials science and engineering and offer key theoretical support for the long-term development of China’s construction industry. Full article

Reinforced concrete durability depends on a passive oxide film protecting embedded steel, sustained by high-alkalinity pore solutions. Cracking fundamentally alters transport, allowing rapid chloride and carbon dioxide ingress, which undermines passivity and accelerates corrosion. Self-healing concrete technologies aim to autonomously restore transport barriers and reestablish electrochemical stability. This review critically synthesizes evidence on healing effectiveness for corrosion mitigation through a dual framework of barrier restoration and interface stabilization, integrating depth-resolved chloride profiles with electrochemical performance indices. Critically, visual crack closure proves an unreliable indicator of corrosion protection. Healing mechanisms exhibit characteristic spatial signatures: autogenous and microbial approaches preferentially seal surface zones with diminishing effectiveness at reinforcement depth, while encapsulated low-viscosity polymers achieve greater depth continuity. However, electrochemical recovery consistently lags transport recovery, with healed specimens achieving only partial restoration of intact corrosion resistance. Recovery effectiveness depends on crack geometry, moisture conditions, and healing mechanism characteristics, with systems performing effectively only within narrow, condition-specific windows. Effective corrosion protection requires coordinated barrier and interface strategies targeting both bulk transport and steel surface chemistry. The path forward demands rigorous field validation emphasizing electrochemical outcomes over appearance metrics, long-term durability assessment, and performance-based verification frameworks to enable predictable service life extension. Full article

Accumulative rolling bonding (ARB) Cu/Nb nanolaminates have been widely observed to exhibit unique and large numbers of interface-based plasticity mechanisms, and these have been associated with the many extraordinary properties of the material system, especially resistances in extreme engineering environments (mechanical/pressure, thermal, irradiation, etc.) and ability to self-heal defects (microstructural, as well as radiation-induced). Recently, anisotropy in the interface shearing mechanisms in the material system has been observed and much discussed. The Cu/Nb nanolaminates appear to shear on the interface planes to a much larger extent in the transverse direction (TD) than in the rolling direction (RD). Related to that, in this present study we observe interface rotation in Cu/Nb ARB nanolaminates under constrained and unconstrained loading conditions. Although the primary driving force for interface shearing was expected only in the RD, additional shearing in the TD was observed. This is significant as it represents an interface rotation, while there was no external rotational driving force. First, we observed interface rotation in in situ rectangular micropillar compression experiments, where the interface is simply sheared in one particular direction only, i.e., in the RD. This is rather unexpected as, in rectangular micropillar compression, there is no possibility of extra shearing or driving force in the perpendicular direction due to the loading conditions. This motivated us to subsequently perform in situ microbeam bending experiments (microbeam with a pre-made notch) to verify if similar interface rotation could also be observed in other loading modes. In the beam bending mode, the notch area was primarily under tensile stress in the direction of the beam longitudinal axis, with interfacial shear also in the same direction. Hence, we expect interface shearing only in that direction. We then found that interface rotation was also evident and repeatable under certain circumstances, such as under an offset loading. As this behaviour was consistently observed under two distinct loading modes, we propose that it is an intrinsic characteristic of Cu/Nb interfaces (or FCC/BCC interfaces with specific orientation relationships). This interface rotation represents another interface-based or interface-mediated plasticity mechanism at the nanoscale with important potential implications especially for design of metallic thin films with extreme stretchability and other emerging applications. Full article

Polymer gel-based triboelectric nanogenerators (TENGs) have emerged as versatile platforms for self-powered sensing due to their inherent softness, stretchability, and tunable conductivity. This review comprehensively explores the roles of polymer gels in TENG architecture, including their function as triboelectric layers, electrodes, and conductive matrices. We analyze four operational modes—vertical contact-separation, lateral-sliding, single-electrode, and freestanding configurations—alongside key performance metrics. Recent studies have reported output voltages of up to 545 V, short-circuit currents of 48.7 μA, and power densities exceeding 120 mW/m², demonstrating the high efficiency of gel-based TENGs. Gel materials are classified by network structure (single-, double-, and multi-network), matrix composition (hydrogels, aerogels, and ionic gels), and dielectric medium. Strategies to enhance conductivity using ionic salts, conductive polymers, and nanomaterials are discussed in relation to triboelectric output and sensing sensitivity. Morphological features such as surface roughness, porosity, and micro/nano-patterning are examined for their impact on charge generation. Application-focused sections detail the integration of gel-based TENGs in health monitoring (e.g., sweat, glucose, respiratory, and tremor sensing), environmental sensing (e.g., humidity, fire, marine, and gas detection), and tactile interfaces (e.g., e-skin and wearable electronics). Finally, we address current challenges, including mechanical durability, dehydration, and system integration, and outline future directions involving self-healing gels, hybrid architectures, and AI-assisted sensing. This review expands the subject area by synthesizing recent advances and offering a strategic roadmap for developing intelligent, sustainable, and multifunctional TENG-based sensing technologies. Full article

Osteochondral repair remains challenging due to cartilage’s limited self-healing capacity and the structural complexity of the osteochondral interface, particularly the hypertrophic layer anchoring cartilage to bone. We fabricated melt electrowritten (MEW) poly(L-lactic acid) (PLLA) scaffolds incorporating 1%, 5%, and 10% hydroxyapatite (HAp) to provide a precise fiber architecture (~200 μm pores) and bone-mimetic biochemical cues. Human nasal chondrocytes (hNCs), currently in clinical trials for knee cartilage repair, were selected for their phenotypic plasticity and established safety profile, facilitating translational potential. HAp–PLLA scaffolds, especially at higher HAp contents, enhanced hNC adhesion, proliferation, mineralization, and maintenance of cartilage-specific ECM compared to PLLA alone. This work demonstrates the first high-HAp MEW-printed PLLA scaffold for osteochondral repair, integrating architectural precision with bioactivity in a clinically relevant cell–material system. Full article

Extended-reach drilling (ERD) offers substantial economic and operational benefits by accessing extensive reservoir sections with fewer surface facilities, yet poses significant frictional challenges due to complex wellbore geometries and extreme operating conditions. This study introduces a multi-interface lubrication evaluation framework. It systematically assesses oil-based drilling fluids (OBDFs) across three downhole contact scenarios: metal–rock, metal–mud cake, and metal–metal interfaces under HTHP conditions. We developed a quantitative, normalized scoring system. Benchmarked against distilled water (score 0) and W1-110 mineral oil (score 100), it integrates frictional data from various tests into a unified metric for lubricant comparison. Three candidate lubricants—PF-LUBE EP, PF-LUBE OB, and CX-300—were evaluated at varying dosages, lithologies, and applied loads. Results show that at 2 wt%, PF-LUBE EP achieved the most consistent performance, reducing friction coefficients by 36.8% (metal–rock), 27.5% (metal–mud cake), and 32.5% (metal–metal), with a normalized average score of 155.39, outperforming PF-LUBE OB and CX-300 by 12.5% and 18.3%, respectively. Its superior performance is attributed to a bionic dual-layer film formed by organophosphorus anchoring and alkyl slip layers, enabling self-healing and stability under cyclic loading and HTHP environments. PF-LUBE OB and CX-300 also demonstrated friction reduction but with lower normalized scores (138.06 and 131.27), reflecting less stability across varied conditions. The proposed framework bridges the gap between laboratory testing and field-scale application by capturing multi-interface behaviors, enabling objective lubricant selection and dosage optimization for complex ERD operations. These findings not only validate PF-LUBE EP as a robust additive but also establish a scalable methodology for the development and optimization of next-generation OBDF formulations aimed at reducing torque, drag, and equipment wear in challenging drilling environments. Full article

In this study, alkali-treated wood flour/dynamic polyurethane composites were successfully prepared through a solvent-free one-pot method and in situ polymerization. The effects of the alkaline treatment process, changes in the flexible long-chain content in the dynamic polyurethane system, and the wood flour filling amount on the interface’s bonding, mechanical, and reprocessing properties were investigated. Partial removal of lignin and hemicellulose from the alkali-treated wood flour enhanced rigidity and improved interface bonding and mechanical strength when combined with dynamic polyurethane. The tensile strength was improved from 5.65–11.00 MPa to 13.08–23.53 MPa. As the composite matrix, dynamic polyurethane could not easily infiltrate all wood flour particles when its content was low or its fluidity was poor. Conversely, excessive content or overly high fluidity led to leakage and the formation of large pores, affecting the mechanical strength. As the polyol content increased, the matrix exhibited greater fluidity, which enabled it to accommodate more wood flour and penetrate the cell cavity or even the cell wall. This improved infiltration enhanced the interface bonding performance of the composites and made their mechanical properties sensitive to changes in wood flour content. The reprocessing ability of the prepared composites decreased with the increase in wood flour content, and the interface bonding was enhanced after reprocessing. The tensile strength retention rate of the composites prepared with alkali-treated wood flour was lower. This study provides a theoretical basis for optimizing the performance of wood fiber/dynamic polyurethane composites and an exploration path for developing self-healing and recyclable wood–plastic composites, which can be applied to building materials, automotive interiors, furniture manufacturing, and other fields. Full article

Next-generation pilot suits are evolving into intelligent, adaptive platforms that integrate advanced polymeric materials, smart textiles, and on-body artificial intelligence. High-performance polymers have advanced in mechanical strength, thermal regulation, and environmental resilience, with fabrication methods like electrospinning, weaving, and 3D/4D printing enabling structural versatility and sensor integration. In particular, functional nanomaterials and hierarchical nanostructures contribute critical properties such as conductivity, flexibility, and responsiveness, forming the foundation for miniaturized sensing and integrated electronics. The integration of flexible fiber-based electronics such as biosensors, strain sensors, and energy systems enables real-time monitoring of physiological and environmental conditions. Coupled with on-body AI for multimodal data processing, autonomous decision-making, and adaptive feedback, these systems enhance pilot safety while reducing cognitive load during flight. This review places a special focus on system-level integration, where polymers and nanomaterials serve as both structural and functional components in wearable technologies. By highlighting the role of nanostructured and functional materials within intelligent textiles, we underline a potential shift toward active human–machine interfaces in aerospace applications. Future trends and advancements in self-healing materials, neuromorphic computing, and dynamic textile systems will further elevate the capabilities of intelligent pilot suits. This review discusses interdisciplinary strategies for developing pilot wearables capable of responding to real-time physiological and operational needs. Full article

With the rising performance demands in road engineering, traditional experiments often fail to reveal the microscopic mechanisms behind asphalt behavior. Molecular dynamics (MD) simulation has emerged as a valuable complement, enabling molecular-level insights into asphalt’s composition, structure, and aging mechanisms. This review summarizes the recent advances in applying MD to asphalt research. It first outlines molecular model construction approaches, including average models, three- and four-component systems, and modified models incorporating SBS, SBR, PU, PE, and asphalt–aggregate interfaces. It then analyzes how MD reveals the key performance aspects—such as high-temperature stability, low-temperature flexibility, self-healing behavior, aging processes, and interfacial adhesion—by capturing the molecular interactions. While MD offers significant advantages, challenges remain: idealized modeling, high computational demands, limited chemical reaction simulation, and difficulties in multi-scale coupling. This paper aims to provide theoretical insights and methodological support for future studies on asphalt performance and highlights MD simulation as a promising tool in pavement material science. Full article

As an emerging energy-saving approach, bio-inspired drag reduction technology has become a key research direction for reducing energy consumption and greenhouse gas emissions. This study introduces the latest research progress on bio-inspired microstructured surfaces in the field of underwater drag reduction, focusing on analyzing the drag reduction mechanism, preparation process, and application effect of the three major technological paths; namely, bio-inspired non-smooth surfaces, bio-inspired superhydrophobic surfaces, and bio-inspired modified coatings. Bio-inspired non-smooth surfaces can significantly reduce the wall shear stress by regulating the flow characteristics of the turbulent boundary layer through microstructure design. Bio-inspired superhydrophobic surfaces form stable gas–liquid interfaces through the construction of micro-nanostructures and reduce frictional resistance by utilizing the slip boundary effect. Bio-inspired modified coatings, on the other hand, realize the synergistic function of drag reduction and antifouling through targeted chemical modification of materials and design of micro-nanostructures. Although these technologies have made significant progress in drag reduction performance, their engineering applications still face bottlenecks such as manufacturing process complexity, gas layer stability, and durability. Future research should focus on the analysis of drag reduction mechanisms and optimization of material properties under multi-physical field coupling conditions, the development of efficient and low-cost manufacturing processes, and the enhancement of surface stability and adaptability through dynamic self-healing coatings and smart response materials. It is hoped that the latest research status of bio-inspired drag reduction technology reviewed in this study provides a theoretical basis and technical reference for the sustainable development and energy-saving design of ships and underwater vehicles. Full article

This study investigates the influence of cerium nitrate (Ce(NO₃)₃·6H₂O) content on the performance of Ce(III)/CF/BN/EPN coatings intended for heat exchangers. A series of Ce(III)/carbon fibre (CF)/boron nitride (BN)/epoxy phenolic (EPN) coatings are fabricated with varying concentrations of Ce(NO₃)₃·6H₂O. The results of SEM and EDS show that the dissolution of cerium nitrate in acetone due to the particulate form causes it to be distributed in a diffuse state in the coating. This diffuse distribution does not significantly alter the porosity or structural morphology of the coating. With the increase in cerium nitrate content, both the EIS test results and mechanical damage tests indicate a progressive improvement in the corrosion resistance and self-healing properties of the coatings, while the thermal conductivity (TC) remains largely unaffected. The Ce in the coating reacts with the water molecules penetrating into the coating to generate Ce₂O₃ and CeO₂ with protective properties to fill the permeable pores inside the coating or to form a passivation film at the damaged metal–coating interface, which enhances the anticorrosive and self-repairing properties of the coating. However, the incorporation of Ce(NO₃)₃·6H₂O does not change the distribution structure of the filler inside the coating. As a result, the phonon propagation path, rate, and distance remain unchanged, leading to negligible variation in the thermal conductivity. Therefore, at a cerium nitrate content of 2.5 wt%, the coating exhibits the best overall performance, characterised by a |Z|_0.1Hz value of 6.08 × 10⁹ Ω·cm² and a thermal conductivity of approximately 1.4 W/(m·K). Full article

This paper reviews the applications and performance advantages of ultra-high-performance concrete (UHPC), engineered cementitious composite (ECC), and recycled aggregate concrete (RAC) in composite flexural members. UHPC is characterized by its ultra-high strength, high toughness, excellent durability, and microcrack self-healing capability, albeit with high costs and complex production processes. ECC demonstrates superior tensile, flexural, and compressive strength and durability, yet it exhibits a lower elastic modulus and greater drying shrinkage strain. RAC, as an eco-friendly concrete, offers cost-effectiveness and environmental benefits, although it poses certain performance challenges. The focus of this review is on how to enhance the load-bearing capacity of composite beams or slabs by modifying the interface roughness, adjusting the thickness of the ECC or UHPC layer, and altering the cross-sectional form. The integration of diverse concrete materials improves the performance of beam and slab elements while managing costs. For instance, increasing the thickness of the UHPC or ECC layer typically enhances the load-bearing capacity of composite beams or plates by approximately 10% to 40%. Increasing the roughness of the interface can significantly improve the interfacial bond strength and further augment the ultimate load-bearing capacity of composite components. Moreover, the optimized design of material mix proportions and cross-sectional shapes can also contribute to enhancing the load-bearing capacity, crack resistance, and ductility of composite components. Nevertheless, challenges persist in engineering applications, such as the scarcity of long-term monitoring data on durability, fatigue performance, and creep effects. Additionally, existing design codes inadequately address the nonlinear behavior of multi-material composite structures, necessitating further refinement of design theories. Full article

This study systematically investigates the mechanism by which total ionizing dose (TID) affects the lifetime degradation of NMOS devices induced by hot-carrier injection (HCI). Experiments involved Cobalt-60 (Co-60) gamma-ray irradiation to a cumulative dose of 500 krad (Si), followed by 168 h annealing at 100 °C to simulate long-term stability. However, under HCI stress conditions (V_D = 2.7 V, V_G = 1.8 V), irradiated devices show a 6.93% increase in threshold voltage shift (ΔV_th) compared to non-irradiated counterparts. According to the IEC 62416 standard, the lifetime degradation of irradiated devices induced by HCI stress is only 65% of that of non-irradiated devices. Conversely, when the saturation drain current (I_Dsat) degrades by 10%, the lifetime doubles compared to non-irradiated counterparts. Mechanistic analysis demonstrates that partial neutralization of E’ center positive charges at the gate oxide interface by hot electrons weakens the electric field shielding effect, accelerating ΔV_th drift, while interface trap charges contribute minimally to degradation due to annealing-induced self-healing. The saturation drain current shift degradation primarily correlates with electron mobility variations. This work elucidates the multi-physics mechanisms through which TID impacts device reliability and provides critical insights for radiation-hardened design optimization. Full article

To overcome the shortcomings of traditional polyurethane, such as poor weather resistance and susceptibility to hydrolysis, this study systematically explores the preparation techniques of organic silicon-modified polyurethane and its application in intelligent sports fields. By introducing siloxane into the polyurethane matrix through copolymerization, physical blending, and grafting techniques, the microphase separation structure and interfacial properties of the material are effectively optimized. In terms of synthesis processes, the one-step method achieves efficient preparation by controlling the isocyanate/hydroxyl molar ratio (1.05–1.15), while the prepolymer chain extension method optimizes the crosslinked network through dual reactions. The modified material exhibits significant performance improvements: tensile strength reaches 60 MPa, tear resistance reaches 80 kN/m, and the elastic recovery rate ranges from 85% to 92%, demonstrating outstanding weather resistance. In sports field applications, the 48% impact absorption rate meets the requirements for athletic tracks, wear resistance of <15 mg suits gym floors, and the impact resistance for skate parks reaches 55%–65%. Its environmental benefits are notable, with volatile organic compounds (VOC) <50 g/L and a recycling rate >85%, complying with green building material standards. However, its development is still constrained by multiple factors: insufficient material interface compatibility, a comprehensive cost of 435 RMB/m², and the lack of a quality evaluation system. Future research priorities include constructing dynamic covalent crosslinked networks (e.g., self-healing systems), adopting bio-based raw materials to reduce carbon footprint by 30%–50%, and integrating flexible sensing technologies for intelligent responsiveness. Through multidimensional innovation, this material is expected to evolve toward multifunctionality and environmental friendliness, providing core material support for the intelligent upgrading of sports fields. Full article

B₄C is beneficial for forming a glassy film that is effective at impeding oxygen diffusion and improving the oxidation resistance of coatings at high temperature. The effect of B₄C content on the oxidation resistance of a B₄C-SiO₂–Albite/Al₂O₃ (BSA/AO) double-layer coating by the slurry brushing method at 900 °C was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy-dispersive spectroscopy (EDS), and differential scanning calorimetry (DSC) with thermogravimetric analysis (TGA) in this work. It is indicated that the composite coating with 20 wt% B₄C exhibits excellent oxidation resistance at high temperature, which shows a mass loss of only 0.11% for the coated carbon block after being exposed to 900 °C for 196 h. This is attributed to the in situ formation of a thin, dense glass layer with good self-healing ability at the interface of the B₄C-SiO₂–Albite/Al₂O₃ composite coating within 1 h and the persistence and stability of the dense glass layer during exposure. The mechanism is discussed in detail. Full article