Search Results (34)

In civil engineering, with the increasing demand for structural reinforcement and renovation projects, polymer-rich anchoring adhesives have attracted much attention due to their performance advantage of having high strength and have become a key factor in ensuring the safety and durability of buildings. In this study, polymer-rich anchoring adhesives underwent three artificial aging treatments (alkali medium, hygrothermal, and water bath) to evaluate their aging performance. Alkali treatment reduced bending strength by up to 70% (sample 5#) within 500 h before stabilizing, while hygrothermal and water-curing treatments caused reductions of 16–51% and 15–77%, respectively, depending on adhesive composition. Dynamic thermomechanical analysis revealed significant loss factor decreases (e.g., epoxy adhesives dropped from >1.0 to stable lower values after 500 h aging), indicating increased rigidity. Infrared spectroscopy confirmed chemical degradation, including ester group breakage in vinyl ester resins (peak shifts at 1700 cm⁻¹ and 1100 cm⁻¹) and molecular chain scission in unsaturated polyesters. The three test methods consistently demonstrated that 500 h of aging sufficiently captured performance trends, with alkali exposure causing the most severe degradation in sensitive formulations (e.g., samples 5# and 6#). These results can be used to establish quantitative benchmarks for adhesive durability assessment in structural applications. Full article

Asphalt binder aging under natural exposure critically determines pavement durability, though current research inadequately captured performance evolution across diverse regional climates. This study investigated climate-driven degradation mechanisms through 12-month all-weather aging (AWA) tests in Gansu, Shandong, and Beijing via rheological (G-R parameter, stiffness modulus S-value) and chemical analyses (carbonyl index I_C=O, sulfoxide index I_S=O). The results demonstrated significant region-dependent aging disparities beyond laboratory simulation. In Gansu, extreme thermal fluctuations and UV radiation accelerated hardening via thermal stress cycles and photo-oxidation, yielding 52.4% higher G-R parameter than PAV. In Shandong, humid saline environments triggered sulfur oxidation-driven electrochemical corrosion, increasing I_S=O by 4.2% compared to PAV. In Beijing, synergistic UV–thermal oxidation elevated I_C=O and S-value by 8% and 40.7%, respectively versus PAV. Critically, I_C=O exhibited strong positive correlations with rheological degradation across regions (r > 0.90, p < 0.01). Based on I_C=O, the 12-month all-weather aging rate in Beijing exceeded Gansu and Shandong by 18.5% and 68%, revealing UV–thermal coupling as the most severe degradation pattern. Novelty lies in quantifying region-specific multi-factor coupling effects (UV–thermal, hygrothermal–salt, etc.) and demonstrating their superior severity over PAV (Beijing > Gansu > Shandong). Dominant environmental factors showed distinct regional variations: UV radiation and temperature difference dominated in Gansu (I_C=O, r = 0.76) and Beijing (0.74), while precipitation—I_C=O correlation prevailed in Shandong (0.76), yet multi-factor coupling ultimately governed aging. These findings provide theoretical foundations for region-tailored and climate-resilient asphalt pavement design. Full article

Paper relics, as carrieres of historical civilization’s records and inheritance, could be severely acidic and brittle over time. In this study, the multi-functional dispersion of nanometer magnesium oxide (MgO) carried by 3-aminopropyl triethoxysilane-modified bacterial cellulose (KH550-BC) was applied in the impregnation process to repair aged paper, aiming at solving the key problems of anti-acid and strength recovery in the protection of ancient books. The KH550-BC/MgO treatment demonstrated enhanced functional efficacy in repairing aged paper, attributed to the homogeneous and stable distribution of MgO within the nanofibers of BC networks, with minimal impact on the paper’s wettability and color. Furthermore, the treatment facilitated the formation of adequate alkali reserves and hydrogen bonding, resulting in superior anti-aging properties in the treated paper during prolonged preservation. Even after 30 days of hygrothermal aging tests, the paper repaired by KH550-BC/MgO was still in a gently alkaline environment (pH was about 7.56), alongside a 32.18% elevation compared to the untreated paper regarding the tear index. The results of this work indicate that KH550-BC/MgO is an effective reinforcement material for improving the long-term restoration of ancient books. Full article

Three-dimensional braided composites (3D-BCs) have better specific strength and stiffness than two-dimensional planar composites (2D-PCs), so they are widely used in modern industrial fields. In this paper, two kinds of 3D four-directional braided composites (3D4d-BCs) with different braided angles (15°, denoted as H15, and 30°, denoted as H30) were subjected to hydrothermal aging treatments, low-velocity impact (LVI) tests, and compression after impact (CAI) tests under different conditions. This study systematically studied the hygroscopic behavior and the effect of hygrothermal aging on the mechanical properties of 3D4d-BC. The results show that higher temperatures and smaller weaving angles can significantly improve the moisture absorption equilibrium content. When the moisture absorption content is balanced, the energy absorption effect of 3D4d-BC is better, but the integrity and residual compression rate will be reduced. Due to the intervention of oxygen molecules, the interface properties between the matrix and the composite material will be reduced, so the compressive strength will be further reduced. In the LVI test, the peak impact load of H15 is low. In CAI tests, the failure of H15 mainly occurs on the side, and the failure form is buckling failure. The main failure direction of H30 is 45° shear failure. Full article

High-viscosity modified asphalt binder (HVMA) is used widely as a polymer-modified binder in porous asphalt pavement because it can improve the cohesiveness of the asphalt mixture. However, because of the high voidage in the mixture, HVMA is vulnerable to aging induced by temperature, oxygen, water, sunlight, and other climatic conditions, which degrades the performance of pavement. The properties of asphalt binder are affected adversely by the effects of hygrothermal environments in megathermal and rainy areas. Therefore, it is essential to study the aging characteristics of HVMA under the influence of hygrothermal environments to promote its application as a high-viscosity modifier. A hygrothermal cycle aging test (HCAT) was designed to simulate the aging of HVMA when rainwater was kept inside of the pavement after rainfall in megathermal areas. One kind of base bitumen and three kinds of HVMA (referred to as SBS, A, and B, respectively) were selected in this study. Short-term aging tests, hygrothermal cycling aging tests, and long-term aging tests were performed on the base bitumen and three kinds of modified asphalt binder. Fourier-transform infrared spectroscopy (FTIR), thermo-gravimetric analysis (TGA), and dynamic shear rheological (DSR) tests were used to evaluate the properties of the binders on the micro and macro scales. By comparing the index variations of the four binders before and after aging, the effects of the hygrothermal environment on the properties of HVMA were studied. It was found that the effects of the hygrothermal environment expedited the decomposition of the polymer and the formation of carbonyl groups compared with the TFOT and PAV test, which TGA confirmed further. Moreover, the thermal stability of the samples was improved after HCAT. In addition, the master curves of the complex modulus showed that hygrothermal cycles made the high-temperature rutting resistance of asphalt binder increase significantly. All of the results above verified that the effect of hygrothermal cycling could accelerate the aging of HVMA and shorten its service life. Full article

To investigate the potential of modified epoxy resin for repairing and strengthening historical wooden structures, this study utilized polyurethane and silicone-modified epoxy resin as the base, alongside a polyamine curing agent. The resin mixture was cured at ambient temperature, resulting in the creation of ten unique epoxy resin systems. Investigation into the chemical structure and alterations to the glass transition temperature were conducted. The study conducted tests and characterization of viscosity, curing rate, mechanical properties, stress failure mode, hygrothermal aging resistance, and bonding properties. The results reveal that the curing degree of the two modified epoxy resins is high after being cured at room temperature, and the chemical structure and curing rate show insignificant changes. The range of the glass transition temperature for the modified epoxy resin is between 61.31 °C and 70.51 °C. The incorporation of polyurethane and silicone molecular chains into the epoxy resin cross-linking curing system enhances the toughness of the epoxy resin. The modified resin achieves a maximum elongation at break that is 5.18 times greater than that of the unmodified resin, along with a maximum tensile strength and a compressive strength that are 7.94 and 1.74 times, respectively, higher than those in the Chinese technical specifications for the maintenance and reinforcement of ancient wooden structures. The increase in toughness changes the failure mode of the cured epoxy resin. The modified epoxy resin exhibits great bonding ability to aged wood, with a shear strength of up to 9.6 MPa along the grain. As a result, the modified epoxy resin meets the requirements for the reinforcement and repair of the timber members of ancient buildings. Full article

In order to investigate the durability of fiber-reinforced polymer composites in hygrothermal environments, hygrothermal accelerate aging tests, for 360 days at 70 °C, RH70%; 70 °C, RH85%; 85 °C, RH70%; and 85 °C, RH85% and natural storage for 2 years in Guangzhou, China, were carried out for composite laminates. Then, the moisture absorption and interlaminar shear strength were measured. The hygrothermal damage mechanism of the composite was studied by Fourier transform infrared (FTIR), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), and field emission scanning electron microscopy (FSEM). A dual stress storage life prediction model and the equivalent relationship between natural storage and hygrothermal acceleration were established. The results show that the order of moisture absorption rates, moisture absorption contents, and the severity effect order on the interlaminar shear strength is RH85%; 85 °C > 70 °C; RH85% > 85 °C; RH70% > 70 °C; and RH70%. The time to achieve an effective moisture absorption balance is opposite to this. The moisture absorption rate meets Fick’s law before the effective moisture absorption balance, and then shows a linear trend. The interlayer shear strength still decreases exponentially with aging, which is mainly caused by the resin plasticization and interface weakening. Hygrothermal accelerated aging for 13.4831 days at 85 °C; RH85% is equivalent to that for one-year actual storage in Guangzhou. According to the failure criterion of shear strength decreasing to 77%, the storage life of T700/epoxy in Guangzhou is 14.4661 years. Full article

The aim of this work is to analyze the effect of water absorption on the mechanical properties and damage mechanisms of polyester/glass fiber/jute fiber hybrid composites obtained using the compression molding and vacuum-assisted resin transfer molding (VARTM) techniques with different stacking sequences. For this purpose, the mechanical behavior under tensile stress of the samples was evaluated before and after hygrothermal aging at different temperatures: TA, 50 °C, and 70 °C for a period of 696 h. The damage mechanism after the mechanical tests was evaluated using SEM analysis. The results showed a tendency for the mechanical properties of the composites to decrease with exposure to an aqueous ambient, regardless of the molding technique used to conform the composites. It was also observed that the stacking sequence had no significant influence on the dry composites. However, exposure to the aqueous ambient led to a reduction in mechanical properties, both for the molding technique and the stacking sequence. Damage such as delamination, fiber pull-out, fiber/matrix detachment, voids, and matrix removal were observed in the composites in the SEM analyses. Full article

With increasing attention being paid to environmental issues, the application of natural fibers in fiber-reinforced composites has attracted more and more attention. Composite materials with basalt fibers (BFs) as reinforcement have excellent properties and are widely used in many fields. Hydrothermal aging crucially influences the durability of basalt fiber/epoxy resin composites (BF/ERCs). In this study, BFs were used as reinforcing materials, whose surfaces were modified with a rare earth modification solution (CeCl₃). The density, mechanical performance, and chemical properties of BF/ERCs subjected to hygrothermal aging were analyzed by the weight method, static mechanical performance testing, scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FT-IR). The effects of the modification solution with different Ce concentrations on the water absorption, tensile, bending and interlaminar shear strength (ILSS) of BF/ERCs were investigated. The test results showed that the water absorption of BF/ERCs treated with a modification solution that contained Ce 0.5 wt % as the minimum value and the retention rate of the mechanical properties of BF/ERCs reached maximum values after hygrothermal aging. Full article

The main advantage of green composites is their biodegradability, but this biodegradability can also be considered a drawback if the degradation appears during the service life of the component. Therefore, the study of the mechanical behavior of green composites after hygrothermal aging tests is necessary to analyze their degradation process. This study aims to comprehensively analyze the hygrothermal aging behavior and aging mechanism of flax-fiber-reinforced polylactic acid (PLA) biocomposites. The fully biodegradable composites are manufactured by compression molding. In addition, the influence of atmospheric-pressure plasma treatment on the mechanical properties of the biocomposite is studied. Specimens are exposed to water vapor and 40 °C environmental conditions in a stove for up to 42 days. Several specimens of each type are taken out at regular intervals and tested to examine the water absorption, mechanical properties, and thermal characterization. The results show that the stiffness was significantly reduced after 24 h due to matrix degradation, while the strength was reduced only after three weeks. Full article

Fiber-reinforced polymer composites have been highlighted as ideal candidates for structural applications in marine renewable energy devices, such as tidal turbines and wave energy converters. It is well understood that harsh marine environments can cause strength degradation of composite laminates, which has been extensively researched at the coupon scale; however, no research has investigated how this translates into larger-scale composite structures. This paper presents a subcomponent-scale study which investigates the effects of hygrothermal aging and subsequent static and fatigue characterization of thick composite T-bolt connections as part of a large, multilaboratory materials research effort. Of the glass-reinforced epoxy and vinylester-epoxy matrix composites tested, both showed measurable static strength degradation (4–36%) after being hygrothermally aged, even though the composite specimens were only partially saturated with water. Under tension–tension fatigue loading, the epoxy specimens performed very well in their dry states but exhibited significant degradation after hygrothermal aging. In comparison, the vinylester-epoxy specimens had much shorter fatigue lives in their dry states but exhibited no degradation after hygrothermal aging. Overall, this research demonstrates that hygrothermal aging can have significant effects on the ultimate strengths and fatigue lives of even partially saturated thick composite T-bolt connections, indicating that degradation of the outer plies on thick composite laminates can have pronounced effects on the whole structure. It discusses the challenges of building an understanding of the effects of harsh marine environments in large-scale composite structures. Full article

Currently, the construction sector is witnessing a growing demand for lightweight solutions, which can be justified by the need to adopt high-performance solutions and the fact that the industry is struggling with a shortage of skilled labour. In this sense, this study focuses on a novel and flexible building wall system, constructed using an innovative extensible LSF profile. To enhance its functionality, a monitoring system comprising printed sensors was integrated into the wall. These sensors underwent a thorough verification process. To evaluate the hygrothermal performance of the complete LSF wall solution and validate the novel monitoring system, an extensive ageing test focused on heat/rain, freeze/thaw cycles was conducted on a large-scale wall prototype. Additionally, this research introduces a novel approach by simulating exceptional solar radiation conditions, surpassing the standard cycles outlined in EAD 040083-00-0404, for the first time in this kind of solution. The results cover the measurements taken inside the building system using the incorporated monitoring system. Additionally, supplementary external temperature and heat flow sensors were used to determine the thermal transmittance. Visual and thermography inspections were also carried out. The findings reveal no instances of failures or defects that could potentially impact the hygrothermal behaviour of the system. The hybrid LSF constructive solution leads to more stable temperatures on the inner surface. The presence of direct solar radiation can raise surface temperatures by up to 5 °C compared to surfaces not exposed to such radiation, even when a light-coloured surface is used. The monitoring system worked correctly. In conclusion, the innovative profile proved to be resistant to hygrothermal cycles and the monitoring system developed is efficient. Full article

Basalt Fibre Reinforced Polymer (BFRP)-bonded structures are lightweight, high strength, economical, and environmentally friendly, which is very advantageous in the civil sector. The aim of this paper is to provide a comprehensive account of the hygrothermal degradation and failure mechanisms of BFRP-bonded structures by comparing the residual properties of two epoxy adhesive BFRP single-lap joints after ageing for 240 h, 480 h, and 720 h in an extreme hygrothermal environment with pure water at 80 °C. The hydrophilicity and thermal stability of the two adhesives were firstly compared by water absorption and Thermogravimetric Analysis (TGA) tests, and the hygrothermal degradation of the molecular chains and the reduction in T_g were characterised by Fourier Transform Infra-Red (FTIR) spectroscopy and Differential Scanning Calorimetry (DSC) curves. The failure strength and load-displacement curves of the two joints were then compared, and it was found that the strength and stiffness had different trends, while the paired t-test was used to demonstrate the correlation between the failure strength and the adhesive T_g, as well as the difference in the failure mechanisms of the two joints caused by the water absorption rate. The analysis of macrosections and Scanning Electron Microscope (SEM) images summarised the process and reasons for the transition of the failure mode from fibre tearing to hybrid failure, and finally, the changes in elemental concentration and O/C values were analysed by Energy Dispersive X-ray Analysis (EDX), which proved that the degree of hydrolysis could not be used as a judgement of the degradation degree of the joint alone, and provided data support for the application of the BFRP-bonded structure in the humid and hot environment. Full article

The present work studies the response to hygrothermal ageing of natural fibre composites (NFCs) against synthetic fibre composites when using three different types of polymers as matrices. For ageing, coupons were fully immersed in distilled water at 23, 40, and 60 °C for a total ageing period of 56 days. Flax fibre-reinforced composites, using two recyclable polymer systems: (i) a bio-based recyclable epoxy and (ii) an acrylic-based liquid thermoplastic resin, were tested against conventional glass fibre-reinforced composites employing a synthetic (petroleum-based) epoxy. Different fibre/polymer matrix material combinations were tested to evaluate the effects of hygrothermal ageing degradation on the reinforcement, matrix, and fibre/matrix interface. The hygrothermal ageing response of unaged and aged composite coupons was assessed in terms of flexural and viscoelastic performance, physicochemical properties, and microscopy (SEM—Scanning Electron Microscopy). Full article

Conductive polymers and their composites have been widely applied in different applications, including sensing applications. Herein, we constructed a conductive composite of polypropylene, carbon black, and multi-walled carbon nanotubes (PP/CB/MWCNTs) to experimentally study its sensing behaviors in a humid thermal environment. The as-synthesized PP/CB/MWCNT composite polymer was immersed in simulated sweat in deionized water at 67 °C. Regarding their electrical and mechanical properties, different experimental parameters, such as cyclic loading and hygrothermal aging, were investigated by recording the mass changes, carrying out strain sensing experiments, and performing dynamic mechanical analyses before and after the immersion test. The results reveal that the filler content improved the rate of water absorption but decreased at higher concentrations of the solution. The sensitivity of the material decreased by up to 53% after the hygrothermal ageing and cyclic loading. Moreover, the sensitivity under cyclic compression loading decreased with an increasing immersion time, qualitatively illustrated by an effective quantum tunneling effect and conducting path model. Finally, hygrothermal aging reduced the composite’s glass transition temperature. This reduction was the most significant for specimens immersed in deionized water, ascribed to the moisture absorption, reducing the molecular chain activity. Full article