Search Results (1,033)

Millisecond lasers, with their high processing efficiency and large power, are widely used in manufacturing fields such as aerospace. This study aims to investigate the effects of different processing parameters on the micro-hole processing of 316 heat-resistant steel using millisecond lasers. Through the control variable method, the study examines the impact of pulse energy, pulse count, and pulse width on the quality of micro-holes, including the entrance diameter, exit diameter, and taper. Furthermore, combined with orthogonal experiments and COMSOL Multiphysics 6.2 simulations, the study explores the influence of pulse width on the formation of blind holes. The experimental results show that when the pulse energy is 2.2 J, the taper is minimal (2.2°), while the taper reaches its peak (2.4°) at 2.4 J pulse energy. As the pulse count increases to 55–60 pulses, the exit diameter stabilizes, and the taper decreases to 1.8°. Blind holes begin to form when the pulse width exceeds 1.2 ms. When the pulse width is 1.2 ms, pulse energy is 2.4 J, and pulse count is 50, the entrance diameter of the blind hole reaches its maximum, indicating that longer pulse widths result in more significant energy reflection and thermal accumulation effects. COMSOL simulations reveal that high-energy pulses cause intense melt ejection, while longer pulse widths exacerbate thermal accumulation at the micro-hole entrance, leading to blind hole formation. This study provides important process references for laser processing of through-holes and blind holes in heat-resistant steel. Full article

Morphology is an important characteristic of the hydraulic and gravitational processes driving gully erosion. In this study, field scouring experiments were conducted on five experimental plots using terrestrial laser scanning to study gully erosion processes. The erosion and deposition on a gully slope were quantified using the M3C2 algorithm. The results show that the proportion of sediment yield of the gully slope in the whole slope–gully system ranged from 81.5% to 99.7% for different flow discharges (25, 40, 55, 70, and 85 L/min). Compared with low flow discharges (25 and 40 L/min), the gully slope presented more intense gully head retreat and higher erosion intensity under relatively high discharges (55, 70, and 85 L/min). Alcove expansion processes were characterized by horizontal and vertical cycles. Vertical dynamic changes were dominated by the co-evolution of collapses of the gully head and the deepening of the alcove. Horizontal development mainly manifested as a widening of the alcove caused by the hydraulic erosion of the gully wall. The roughness of the gully slope increased gradually with the increase in scour times and then tended towards stability. These results provide a reference for understanding the processes and mechanisms of gully erosion. Full article

This study synthesizes and comparatively investigates two squaric acid-based phthalocyanine-like dyes, SNF and its long-chain alkylated derivative LNF, to systematically elucidate the influence of peripheral hydrophobic groups on their third-order nonlinear optical (NLO) properties. The NLO characteristics were comprehensively characterized using femtosecond Z-scan and I-scan techniques at both 800 nm and 900 nm. Both dyes exhibited strong saturable absorption (SA), confirming their potential as saturable absorbers. Critically, the comparative analysis revealed that SNF exhibits a significantly greater nonlinear absorption coefficient (β) compared to LNF under identical conditions. For instance, at 800 nm, the β of SNF was approximately 3–5 times larger than that of LNF. This result conclusively demonstrates that the introduction of long hydrophobic alkyl chains attenuates the NLO response. Furthermore, I-scan measurements revealed excellent SA performance, with high modulation depths (e.g., LNF: 43.0% at 900 nm) and low saturation intensities. This work not only clarifies the structure–property relationship in these D-A-D dyes but also presents a clear strategy for modulating the NLO properties of organic chromophores for applications in near-infrared pulsed lasers. Full article

This study focuses on the analysis of soliton solutions within the framework of the time-fractional cubic–quintic nonlinear Schrödinger equation (TFCQ-NLSE), a powerful model with broad applications in complex physical phenomena such as fiber optic communications, nonlinear optics, optical signal processing, and laser–tissue interactions in medical science. The nonlinear effects exhibited by the model—such as self-focusing, self-phase modulation, and wave mixing—are influenced by the combined impact of the cubic and quintic nonlinear terms. To explore the dynamics of this model, we apply a robust analytical technique known as the sub-ODE method, which reveals a diverse range of soliton structures and offers deep insight into laser pulse interactions. The investigation yields a rich set of explicit soliton solutions, including hyperbolic, rational, singular, bright, Jacobian elliptic, Weierstrass elliptic, and periodic solutions. These waveforms have significant real-world relevance: bright solitons are employed in fiber optic communications for distortion-free long-distance data transmission, while both bright and dark solitons are used in nonlinear optics to study light behavior in media with intensity-dependent refractive indices. Solitons also contribute to advancements in quantum technologies, precision measurement, and fiber laser systems, where hyperbolic and periodic solitons facilitate stable, high-intensity pulse generation. Additionally, in nonlinear acoustics, solitons describe wave propagation in media where amplitude influences wave speed. Overall, this work highlights the theoretical depth and practical utility of soliton dynamics in fractional nonlinear systems. Full article

Fluid resuscitation after thermal injury is paramount to avoid burn shock and restore organ perfusion. Both over- and under-resuscitation can lead to unintended consequences affecting patient outcomes. While many studies have examined systemic effects, limited data exist on how fluid resuscitation impacts burn wound progression in the acute period. Furthermore, the mechanisms underlying burn wound progression remain not fully understood. This study used a swine model to investigate how varying resuscitation levels affect peri-burn wound dynamics. Twenty-seven female Yorkshire pigs were anesthetized, subjected to 40% total body surface area burn and 15% hemorrhage, then randomized (n = 9) to receive decision-support-driven (adequate, 2–4 mL/kg/%TBSA), fluid-withholding (under, <1 mL/kg/%TBSA), or high-constant-rate (over, >>4 mL/kg/%TBSA) resuscitation. Pigs were monitored for 24 h in an intensive care setting prior to necropsy. Laser Doppler Imaging (LDI) was conducted pre-burn and at 2, 6, 12, and 24 h post burn to assess perfusion. Biopsies were taken from burn, peri-burn (within 2 cm), and normal skin. RNA was isolated at 24 h for the qRT-PCR analysis of IL-6, CXCL8, and IFN-γ. At hour 2, LDI revealed increased peri-burn perfusion in over-resuscitated animals vs. under-resuscitated animals (p = 0.0499). At hour 24, IL-6 (p = 0.0220) and IFN-γ (p = 0.0253) were elevated in over-resuscitated peri-burn skin. CXCL8 showed no significant change. TUNEL staining revealed increased apoptosis in over- and under-resuscitated peri-burn skin. Differences in perfusion and cytokine expression based on resuscitation strategy suggest that fluid levels may influence burn wound progression. Full article

Hierarchical surface structuring is a critical aspect of advanced materials design, impacting fields ranging from optics to biomimetics. Among several laser-based methods for complex structuring of photo-responsive surfaces, the broadband vectorial interferometry proposed here offers unique performances. Such a method leverages a polychromatic laser source, an unconventional choice for holographic encoding, to achieve deterministic multiscale surface structuring through interference light patterning. Azopolymer films are used as photosensitive substrates. By exploring the interaction between optomechanical stress modulations at different spatial periodicities induced within the polymer bulk, we demonstrate the emergence of hierarchical Fourier surfaces composed of multiple deterministic levels. These structures range from sub-micrometer to tens of micrometers scale, exhibiting a high degree of control over their morphology. The experimental findings reveal that the optical encoding scheme significantly influences the resulting topographies. The polarization light patterns lead to more regular and symmetric hierarchical structures compared to those obtained with intensity patterns, underscoring the role of vectorial light properties in controlling surface morphologies. The proposed method is fully scalable, compatible with more complex recording schemes (including multi-beam interference), and it is applicable to a wide range of advanced technological fields. These include optics and photonics (diffractive elements, polarimetric devices), biomimetic surfaces, topographical design, information encoding, and anti-counterfeiting, offering a rapid, reliable, and versatile strategy for high-precision surface structuring at a submicrometric scale. Full article

Extensive numerical simulations were performed in MATLAB R2020b based on the classical nonlinear Thomson scattering theory and single-electron model, to systematically examine the influence of initial phase in tightly focused linearly polarized laser pulses on the radiation characteristics of multi-energy-level electrons. Through our research, we have found that phase variation from 0 to 2π induces an angular bifurcation of peak radiation intensity, generating polarization-aligned symmetric lobes with azimuthal invariance. Furthermore, the bimodal polar angle decreases with the increase of the initial energy. This phase-controllable bimodal distribution provides a new solution for far-field beam shaping. Significantly, high-harmonic intensity demonstrates π-periodic phase-dependent modulation. Meanwhile, the time-domain pulse width also exhibits 2π-cycle modulation, which is synchronized with the laser electric field period. Notably, electron energy increase enhances laser pulse peak intensity while compressing its duration. The above findings demonstrate that the precise control of the driving laser’s initial phase enables effective manipulation of the radiation’s spatial characteristics. Full article

Belle II is a particle physics experiment working at an high luminosity collider within a hard irradiation environment. The Time-Of-Propagation detector, aimed at the charged particle identification, surrounds the Belle II tracking detector on the barrel part. This detector is composed by 16 modules, each module contains a finely fused silica bar, coupled to microchannel plate photomultiplier tube (MCP-PMT) photo-detectors and readout by high-speed electronics. The MCP-PMT lifetime at the nominal collider luminosity is about one year, this is due to the high photon background degrading the quantum efficiency of the photocathode. An alternative to these MCP-PMTs is multi-pixel photon counters (MPPC), known as silicon photomultipliers (SiPM). The SiPMs, in comparison to MCP-PMTs, have a lower cost, higher photon detection efficiency and are unaffected by the presence of a magnetic field, but also have a higher dark count rate that rapidly increases with the integrated neutron flux. The dark count rate can be mitigated by annealing the damaged devices and/or operating them at low temperatures. We tested SiPMs, with different dimensions and pixel sizes from different producers, to study their time resolution (the main constraint that has to satisfy the photon detector) and to understand their behavior and tolerance to radiation. For these studies we irradiated the devices to radiation up to $5\times {10}^{11}1$ MeV neutrons equivalent (neq) per cm² fluences; we also started studying the effect of annealing on dark count rates. We performed several measurements on these devices, on top of the dark count rate, at different conditions in terms of overvoltage and temperatures. These measurements are: IV-curves, amplitude spectra, time resolution. For the last two measurements we illuminated the devices with a picosecond pulsed laser at very low intensities (with a number of detected photons up to about twenty). We present results mainly on two types of SiPMs. A new SiPM prototype developed in collaboration with FBK with the aim of improving radiation hardness, is expected to be delivered in September 2025. Full article

Fiber fault detection based on the time-delay signature of an optical feedback semiconductor laser has the advantages of high sensitivity, precise location, and a simple structure, which make it widely applicable. The sensitivity of this method is determined by the feedback strength inducing the nonlinear state of the laser. This paper proposes a feedback compensation method to reduce the requirement of the fault echo intensity for the laser to enter the nonlinear state, significantly enhancing detection sensitivity. Numerical simulations analyze the impact of feedback compensation parameters on fault detection sensitivity and evaluate the performance of the laser operating at different pump currents. The results show that this method achieves a 9.33 dB improvement in sensitivity compared to the original approach, effectively addressing the challenges of detecting faults with high insertion losses in optical networks. Full article

With the rapid development of the livestock farming industry, the treatment of livestock farming wastewater has become increasingly important. The microbial-algal biofilm method has gained widespread attention for cattle wastewater treatment owing to its non-toxic nature, resistance to shock loading, and high treatment efficiency. In this study, three types of substrates—polyurethane sponge, ceramic material, and moving bed biofilm reactor media—were evaluated. The formation of biofilms was assessed through variations in chlorophyll content, microscopic observations, and measurements of biofilm dry weight and attachment rate. Biofilm characterization on the different substrates was conducted via Fourier transform infrared spectroscopy, confocal laser scanning microscopy, and scanning electron microscopy. The results demonstrated that polyurethane sponge was the most effective substrate. Furthermore, a single-factor experiment was conducted to optimize the cultivation conditions for the microbial-algal biofilms and identify the optimal parameters based on the ability of the biofilm to remove COD, TN, TP, and NH₄⁺-N. The optimal conditions were as follows: an illumination intensity of 8000 lux, red light, a temperature of 20 °C, a pH of 7, and an aeration intensity of 8 L/min. Under these conditions, the pollutant removal rates were exceptionally high: ~73.4% for COD, 51.8% for TP, 57.0% for TN, and 75.1% for NH₄⁺-N. Full article

Background: Snoring and mild to moderate obstructive sleep apnoea (OSA) are common sleep-related breathing disorders with increasing demand for minimally invasive treatment options. This study aimed to systematically evaluate the efficacy and safety of erbium:yttrium–aluminium–garnet (Er:YAG) laser therapy for these conditions. Methods: A systematic review and meta-analysis were conducted in line with PRISMA guidelines. Studies published between 2015 and 2025 were retrieved from major biomedical databases based on predefined inclusion criteria. Data were extracted on treatment outcomes, laser parameters, patient characteristics, and adverse effects. Results: Fifty-six studies were included. Er:YAG laser treatment, particularly in non-ablative SMOOTH and long-pulse modes, significantly reduced snoring intensity and improved subjective sleep quality. High patient satisfaction (65–85%) and a favourable safety profile were observed, with adverse effects generally mild and transient. Therapeutic effects typically lasted 12–24 months, though 25–40% of patients required maintenance sessions. Treatment success was associated with BMI, oropharyngeal anatomy, smoking status, and baseline apnoea-hypopnoea index scores (AHI 5–30 events/hour). Conclusions: Er:YAG laser therapy appears to be a safe and effective short- to medium-term treatment for selected patients with snoring or mild to moderate OSA. Optimising patient selection and treatment protocols may enhance long-term outcomes. Based on moderate-quality evidence for the immediate effects and safety profile, but low to very low quality evidence for long-term outcomes, erbium:yttrium–aluminium–garnet laser treatment appears to be a potentially effective and well-tolerated option for achieving short- to medium-term improvement in carefully selected patients with primary snoring or mild to moderate obstructive sleep apnoea. The practical significance of these findings lies in the refinement of candidate selection criteria, laser parameter settings, and the development of optimal protocols for long-term snoring control. Full article

Spodumene (LiAlSi₂O₆) is a key lithium source mineral for energy storage devices, making the accurate and rapid analysis of its elemental composition crucial for the battery industry. This study explores the use of laser-induced breakdown spectroscopy (LIBS) combined with the standard addition method to analyze Be, Na, and K in spodumene. The method achieved relative errors of 5%–15% compared to inductively coupled plasma optical emission spectroscopy (ICP-OES), without requiring certified standards. To ensure accuracy, non-resonance emissions were used for Be and Na to minimize self-absorption effects. Although K analysis faced challenges due to strong self-absorption in resonance emissions, focusing on weak edge intensity reduced the relative error significantly. Our results suggest that LIBS combined with the standard addition method is a promising approach for lithium ore analysis, eliminating the need for certified standard materials and complex sample preparation steps such as acid digestion and high-factor dilution. Full article

The remote sensing of seismic waves in challenging and hazardous environments, such as active volcanic regions, remains a critical yet unresolved challenge. Conventional methods, including laser Doppler interferometry, InSAR, and stereo vision, are often hindered by atmospheric turbulence or necessitate access to observation sites, significantly limiting their applicability. To overcome these constraints, this study introduces a Moiré-based apparatus augmented with active convolved illumination (ACI). The system leverages the displacement-magnifying properties of Moiré patterns to achieve high precision in detecting subtle ground movements. Additionally, ACI effectively mitigates atmospheric fluctuations, reducing the distortion and alteration of measurement signals caused by these fluctuations. We validated the performance of this integrated solution through over 1900 simulations under diverse turbulence intensities. The results illustrate the synergistic capabilities of the Moiré apparatus and ACI in preserving the fidelity of Moiré fringes, enabling reliable displacement measurements even under conditions where passive methods fail. This study establishes a cost-effective, scalable, and non-invasive framework for remote seismic monitoring, offering transformative potential across geophysics, volcanology, structural analysis, metrology, and other domains requiring precise displacement measurements under extreme conditions. Full article

In the present work, the influence of external X-ray radiation on the kinetics of multicharged ions in high-temperature plasma is investigated. A generalized diagnostic approach is proposed for the electron density and temperature measurements of photo-pumped plasma based on the relative intensity of the H-like ion resonance line and its dielectronic satellites. Based on detailed kinetic calculations performed for argon plasma, the conditions under which these techniques can be applied without modification to the photo-pumped plasma are determined, and the relative intensities of these lines are calculated for cases where the external influence significantly alters the kinetics of their excitation. The development of such diagnostic methods is of particular importance for the experiments with powerful X-ray free-electron lasers and thermonuclear laser plasma. Full article

The research on high-order transverse modes in lasers was largely abandoned a few years after the invention of the laser in 1960. The main reason for this was that high-order beams are more divergent and less bright than the Gaussian beam. In the present paper, we showed that the behaviour of $L{G}_{p0}$ beams faced to the optical Kerr effect (OKE) varies considerably depending on the mode order (p = 0 or $p\ge 1$). We focused our attention on the properties of $L{G}_{00}$ and $L{G}_{10}$ beams when subject to OKE, and we found that the $L{G}_{10}$ beam keeps its focusability much better than the $L{G}_{00}$ beam. This property has at least two applications concerning first the conception of high-intensity laser chains not based on a Gaussian beam but on an $L{G}_{10}$ beam and second, the use of an $L{G}_{10}$ beam instead of the usual Gaussian beam which can reduce drastically the protection of optical limiters based on OKE; this constitutes a counter-measure against such limiters. Full article