Search Results (5)

The depletion of petroleum reserves and increasing environmental concerns have driven the development of eco-friendly asphalt binders. This research investigates the performance of natural asphalt (NA) modified with waste engine oil (WEO) as a sustainable alternative to conventional petroleum asphalt (PA). The study examines NA modified with 10%, 20%, and 30% WEO by the weight of asphalt to identify an optimal blend ratio that enhances the binder’s flexibility and workability while maintaining high-temperature stability. Comprehensive testing was conducted, including penetration, softening point, viscosity, ductility, multiple stress creep recovery (MSCR), linear amplitude sweep (LAS), energy-dispersive X-ray spectroscopy (EDX), Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). The results reveal that WEO effectively softens NA, improves ductility, and enhances workability, with the 20% WEO blend achieving the best balance of physical and rheological properties. Chemical analysis indicates that WEO increases carbon content and reduces sulfur and impurities, aligning NA’s composition closer to PA. However, excessive WEO (30%) compromises thermal stability and deformation resistance. The findings underscore the potential of WEO-modified NA for sustainable pavement applications, with 20% WEO identified as the optimal content to achieve performance comparable to conventional petroleum asphalt while promoting environmental sustainability. Full article

This study investigates the transformative effects of incorporating Trinidad Lake asphalt (TLA), crumb rubber modifier (CRM), and the warm mix additive leadcap (LC) into petroleum-based asphalt binder PG 64-22. Our results show that LC significantly reduces binder viscosity, leading to easier application and lower energy consumption, especially when combined with TLA and CRM. The addition of TLA and CRM enhances rutting resistance, with notable improvements in both pre- and post-aging conditions, particularly in formulations combining PG 64-22, 20% TLA, and 10% CRM. These formulations exhibit superior performance metrics, such as increased percentage recovery (% rec) and reduced non-recoverable creep compliance (J_nr), indicating improved flexibility and deformation resistance. Furthermore, LC balances increased rigidity and susceptibility to fatigue cracking from higher TLA and CRM levels, respectively. These modifications also promote environmental sustainability by reducing energy usage and emissions during production and paving. This study highlights LC’s critical role in advancing high-performance, eco-friendly warm mix asphalt binders, offering valuable insights for sustainable pavement engineering and setting a new benchmark for advanced asphalt technologies. Full article

Exploring the interface of environmental sustainability and civil infrastructure development, this study introduces waste butter (WB), a byproduct of animal fat processing, as a novel bio-modifier in asphalt production. This approach not only recycles animal waste but also charts a course for sustainable infrastructural development, contributing to a reduced environmental impact and promoting circular economy practices. The experiments incorporated varying WB concentrations (e.g., 3%, 6%, and 9% by weight of binder) into standard AP-5 asphalt, employing advanced analytical tools for comprehensive characterization. These included thin-layer chromatography–flame ionization detection (TLC-FID), Fourier-transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM), thermogravimetric analysis (TGA), and Differential Scanning Calorimetry (DSC). The critical properties of the asphalt blends, such as penetration, softening point, viscosity, ductility, rutting factor (Dynamic Shear Rheometer), and thermal susceptibility (Penetration Index, Penetration–Viscosity Number), were assessed. FT-IR analysis indicated negligible chemical alteration with WB addition, suggesting predominantly physical interactions. TLC-FID showed a decrease in aromatic and asphaltene components but an increase in resin content, highlighting the influence of WB’s fatty acids on the asphalt’s chemical balance. The colloidal instability index (I_C) confirmed enhanced stability due to WB’s high resin concentration. Meanwhile, SEM analysis revealed microstructural improvements with WB, enhancing binder compatibility. TGA demonstrated that even a minimal 3 wt. % WB addition significantly improved thermal stability, while the DSC results pointed to improved low-temperature performance, reducing brittleness in cold conditions. Rheologically, WB incorporation resulted in increased penetration and ductility, balanced by decreased viscosity and softening point, thereby demonstrating its multi-faceted utility. Thermal susceptibility tests emphasized WB’s effectiveness in cold environments, with further evaluation needed at higher temperatures. The DSR findings necessitate careful WB calibration to meet Superpave rutting standards. In conclusion, this research positions waste butter as a superior, environmentally aligned bio-additive for asphalt blends, contributing significantly to eco-friendly civil engineering practices by repurposing animal-derived waste. Full article

In order to address the issues of high viscosity and excessive fume exhaust associated with high-viscosity modified asphalt (HVMA), the objective of this study was to develop an eco-friendly HVMA by incorporating fume suppressants and viscosity-retarding agents (VRAs). To begin with, desulfurization rubber powder (DRP) was utilized as a modifier, and fume suppressants, including activated carbon, a chemical reaction fume suppressant, and a composite fume suppressant combining activated carbon and chemical reaction fume suppressant were added to the HVMA separately. The fume suppression effect and odor level were observed to determine the optimal fume suppressant composition for this study. Based on these observations, an area integration method was proposed, utilizing rotational viscosity testing and temperature sweeping experiments, evaluating the viscosity-retarding effect and mixing temperature when different amounts of Sasobit VRA, Evotherm3G VRA, and a composite VRA of Sasobit and Evotherm3G were added to the HVMA. This approach aimed to identify the eco-friendly HVMA with the most effective fume suppression and viscosity-retarding abilities. Furthermore, the morphology and rheological properties of the eco-friendly HVMA were examined through fluorescence microscopy, zero shear viscosity test, multiple stress creep recovery analysis, liner amplitude sweep test, and frequency sweep test. The results demonstrated that the HVMA formulation consisting of 15% DRP and 1% composite fume suppressant exhibited a satisfactory fume suppression effect and odor level. Based on this, the HVMA formulation containing 0.6% Evotherm3G and 3% Sasobit VRAs displayed the best viscosity-retarding effect while reducing the mixing temperature. Moreover, when compared to common HVMA, the eco-friendly HVMA exhibited excellent high-temperature resistance, successfully accomplishing the dual objectives of ecological friendliness and superior performance. Full article

Asphalt binders have been modified with Crumb rubber (CR) as an effort to fulfil the demand for the development of eco-friendly and sustainable pavements. The objective of this study was to investigate the high temperature rheological behaviors and fatigue performance of crumb rubber modified asphalt (CRMA) binder activated using trans-polyoctenamer (TOR). Long-term and short-term aging tests were performed on samples by thin film oven test (TFOT) and pressure aging vessel (PAV). Rotational viscosity (RV), softening point, and dynamic shear rheometer (DSR) tests were conducted to characterize the rheological and physical performance. A linear amplitude sweep (LAS) test was employed to evaluate the fatigue performance. The results show that TOR-activated CRMA is more capable of hardening the matrix bitumen and improving its high-temperature viscoelastic properties after TFOT. The high temperature viscoelasticity is significantly better than styrene-butadiene-styrene block (SBS) modified asphalt (SBSMA) and CRMA. TOR-activated CRMA exhibits strong rutting resistance, but it is more likely to generate fatigue cracks under the violent advancement of complex modulus. Therefore, TOR active agent has a negative impact on the fatigue performance of CRMA. SBSMA exhibited superior fatigue resistance. The viscosity temperature index (VTS) of TOR-activated CRMA and CRMA was basically identical; the TOR did not significantly improve the temperature sensitivity of CRMA. Full article