Search Results (12)

A supercapacitor’s energy storage capability is greatly dependent on electrode materials. Layered double hydroxides (LDHs) were extensively studied as battery-type electrodes because of their 2D structure and quick intercalation/deintercalation of electrolyte ions. However, the energy storage capability for pristine LDHs is limited by their large aggregation tendency and poor electrical conductivity. Herein, a novel NiCoMn-LDH/SWCNTs (single-walled carbon nanotubes) composite electrode material, with ultrathin NiCoMn-LDH nanosheets dispersedly grown among the highly conductive networks of SWCNTs, was prepared via a facile zeolitic imidazolate framework-67 (ZIF-67)-derived in situ etching and deposition procedure. The NiCoMn-LDH/SWCNTs electrode demonstrates a specific capacitance as large as 1704.3 F g⁻¹ at 1 A g⁻¹, which is ascribed to its exposure of more active sites than NiCoMn-LDH. Moreover, the assembled NiCoMn-LDH/SWCNTs//BGA (boron-doped graphene aerogel) hybrid supercapacitor exhibits a superior capacitance of 167.9 F g⁻¹ at 1.0 A g⁻¹, an excellent energy density of 45.7 Wh kg⁻¹ with a power density of 700 W kg⁻¹, and an outstanding cyclic stability with 82.3% incipient capacitance maintained when subjected to 5000 charge and discharge cycles at the current density of 10 A g⁻¹, suggesting the significant potential of NiCoMn-LDH/SWCNTs as the electrode material applicable in supercapacitors. Full article

Heavy metal poisoning has a life-threatening impact on the human body to aquatic ecosystems. This necessitates designing a convenient green methodology for the fabrication of an electrochemical sensor that can detect heavy metal ions efficiently. In this study, boron (B) and nitrogen (N) co-doped laser-induced porous graphene (LIG_BN) nanostructured electrodes were fabricated using a direct laser writing technique. The fabricated electrodes were utilised for the individual and simultaneous electrochemical detection of lead (Pb²⁺) and cadmium (Cd²⁺) ions using a square wave voltammetry technique (SWV). The synergistic effect of B and N co-doping results in an improved sensing performance of the electrode with better sensitivity of 0.725 µA/µM for Pb²⁺ and 0.661 µA/µM for Cd²⁺ ions, respectively. Moreover, the sensing electrode shows a low limit of detection of 0.21 µM and 0.25 µM for Pb²⁺ and Cd²⁺ ions, with wide linear ranges from 8.0 to 80 µM for Pb²⁺ and Cd²⁺ ions and high linearity of R² = 0.99 in case of simultaneous detection. This rapid and facile method of fabricating heteroatom-doped porous graphene opens a new avenue in electrochemical sensing studies to detect various hazardous metal ions. Full article

Zn-air batteries (ZABs) with neutral electrolytes offer a significantly longer lifespan and better recyclability than alkaline ones. However, low-performance bifunctional catalytic activities for oxygen reduction or evolution reaction (i.e., ORR/OER) in neutral electrolytes still hamper their development. Here, we report iron nanoparticle-decorated nitrogen/boron co-doped reduced graphene oxide aerogel (Fe-NBrGO) with distinguished ORR/OER activity, enabling its application in neutral rechargeable ZABs. Taking advantage of the formation of 3D porous structure of graphene aerogel, N/B-moieties active sites, and Fe-containing active sites, Fe-NBrGO exhibits high ORR onset potential (1.074 and 0.817 V) and adequate OER overpotential (476 and 615 mV) in alkaline and neutral electrolytes, respectively. Fe-NBrGO enables the production of a neutral-ZAB with 34 mW cm⁻² in peak power density and remains stable for a 284 h (~852 cycles) cycling test. This research highlights the rational design of highly active oxygen catalysts for the widespread implementation of new energy storage technologies. Full article

In the present study, nanocomposites having hierarchical nanoflowers (HNFs) -like morphology were synthesized by ultra-sonication approach. HNFs were ternary composite of MgFe₂O₄ and bentonite with boron-, phosphorous- co-doped graphene oxide (BPGO). The HNFs were fully characterized using different analytical tools viz. X-ray photoelectron spectroscopy, scanning electron microscopy, energy dispersion spectroscopy, transmission electron microscopy, X-ray diffraction, vibrating sample magnetometry and Mössbauer analysis. Transmission electron micrographs showed that chiffon-like BPGO nanosheets were wrapped on the MgFe₂O₄-bentonite surface, resulting in a porous flower-like morphology. The red-shift in XPS binding energies of HNFs as compared to MgFe₂O₄-bentoniteand BPGO revealed the presence of strong interactions between the two materials. Box–Behnken statistical methodology was employed to optimize adsorptive and photocatalytic parameters using Pb(II) and malathion as model pollutants, respectively. HNFs exhibited excellent adsorption ability for Pb(II) ions, with the Langmuir adsorption capacity of 654 mg g⁻¹ at optimized pH 6.0 and 96% photocatalytic degradation of malathion at pH 9.0 as compared to MgFe₂O₄-bentonite and BPGO. Results obtained in this study clearly indicate that HNFs are promising nanocomposite for the removal of inorganic and organic contaminants from the aqueous solutions. Full article

In this work, we study the structural and electronic properties of boron nitride bilayers sandwiched between graphene sheets. Different stacking, twist angles, doping, as well as an applied external gate voltage, are reported to induce important changes in the electronic band structure near the Fermi level. Small electronic lateral gaps of the order of few meV can appear near the Dirac points K. We further discuss how the bandstructures change applying a perpendicular external electric field, showing how its application lifts the degeneracy of the Dirac cones and, in the twisted case, moves their crossing points away from the Fermi energy. Then, we consider the possibility of co-doping, in an asymmetric way, the two external graphene layers. This is a situation that could be realized in heterostructures deposited on a substrate. We show that the co-doping acts as an effective external electric field, breaking the Dirac cones degeneracy. Finally, our work demonstrates how, by playing with field strength and p-n co-doping, it is possible to tune the small lateral gaps, pointing towards a possible application of C/BN sandwich structures as nano-optical terahertz devices. Full article

Twin T-graphene (TTG) is a new two-dimensional carbon allotrope of graphene. Heteroatom co-doping is an effective method for the modulation of the physical and chemical properties of two-dimensional materials. This study explored the structural stability, electronic structures, and optical properties of boron and phosphorus co-doped TTG using first-principles calculations. TTG was doped with B and P atoms (BP) at different positions considering 13 different configurations. Pristine TTG has a band gap of 1.89 eV, and all BP co-doped TTG (TTG/BP) systems remain semiconducting with band gaps that gradually decrease with increasing doping concentration. For a given doping concentration, the TTG/BP-ortho systems had a narrower band gap than the corresponding TTG/BP-para systems. The TTG and TTG/BP systems exhibited significant optical anisotropy. In the infrared region, BP co-doping increased the absorption coefficient, and the reflectance and refractive index increased with increasing doping concentration, except for the vertical component of the TTG/BP-ortho system. In the visible region, the absorption coefficient, reflectance, and refractive index decreased with increasing doping concentration for the vertical component, and the peaks were red-shifted from the near-ultraviolet region to the visible region. In the near-ultraviolet region, the reflectance also decreased with increasing doping concentration. The BP co-doping concentration can regulate the electronic structures and optical properties of the TTG, showing that the BP co-doped TTG has potential for application in nanoelectronics and optoelectronics. Full article

A sample of nitrogen and boron co-doped graphene (NB-Gr) was obtained by the hydrothermal method using urea and boric acid as doping sources. According to XRD analysis, the NB-Gr sample was formed by five-layer graphene. In addition, the XPS analysis confirmed the nitrogen and boron co-doping of the graphene sample. After synthesis, the investigation of the electro-catalytic properties of the bare (GC) and graphene-modified electrode (NB-Gr/GC) towards cymoxanil detection (CYM) was performed. Significant differences between the two electrodes were noticed. In the first case (GC) the peak current modulus was small (1.12 × 10⁻⁵ A) and appeared in the region of negative potentials (−0.9 V). In contrast, when NB-Gr was present on top of the GC electrode it promoted the transfer of electrons, leading to a large peak current increase (1.65 × 10⁻⁵ A) and a positive shift of the peak potential (−0.75 V). The NB-Gr/GC electrode was also tested for its ability to detect cymoxanil from a commercial fungicide (CURZATE MANOX) by the standard addition method, giving a recovery of 99%. Full article

A novel solvothermal technique has been developed in the presence of C/N/B precursor for synthesizing B-N-coped graphene quantum dots (GQDs) as non-metal electrocatalysts towards the catalytic glucose oxidation reaction (GOR). Both N-doped GQD and B-N-codoped GQD particles (~4.0 nm) possess a similar oxidation and amidation level. The B-N-codoped GQD contains a B/C ratio of 3.16 at.%, where the B dopants were formed through different bonding types (i.e., N‒B, C‒B, BC₂O, and BCO₂) inserted into or decorated on the GQDs. The cyclic voltammetry measurement revealed that the catalytic activity of B-N-codoped GQD catalyst is significantly higher compared to the N-doped GQDs (~20% increase). It was also shown that the GOR activity was substantially enhanced due to the synergistic effect of B and N dopants within the GQD catalysts. Based on the analysis of Tafel plots, the B-N-codoped-GQD catalyst electrode displays an ultra-high exchange current density along with a reduced Tafel slope. The application of B-N-codoped GQD electrodes significantly enhances the catalytic activity and results in facile reaction kinetics towards the glucose oxidation reaction. Accordingly, the novel design of GQD catalyst demonstrated in this work sets the stage for designing inexpensive GQD-based catalysts as an alternative for precious metal catalysts commonly used in bio-sensors, fuel cells, and other electrochemical devices. Full article

Herein, the boron and nitrogen co-doped 0-dimensional graphene quantum dots (B,N-GQDs) with high quantum yield (QY) were synthesized via microwave-assisted hydrothermal method at 170 °C for 20 min using fresh passion fruit juice and boric acid as the starting materials. The 3–6 layers of B,N-GQDs with mean particle size of 9 ± 1 nm were then used for ultra-sensitive and selective detection of tetracycline in aqueous and biological media. The hybridization of boron and nitrogen atoms into the GQD structures increases the intensity of electronegative, resulting in the enhancement of QY to 50 ± 1%. The B,N-GQDs show their excellent analytical performance on tetracycline determination after 2 min of reaction under an optimal condition at pH 5. The linear range of 0.04–70 µM and with limits of detection (LOD) of 1 nM in phosphate buffer saline (PBS), 1.9 nM in urine and 2.2 nM in human serum are obtained. Moreover, the high selectivity of tetracycline by B,N-GQDs over the other 23 interferences is observed. The π-π interaction and electron donor-acceptor principle play pivotal roles in enhancing the ultra-sensitivity and selectivity of B,N-GQDs toward TC detection. Moreover, the B, N-GQD based paper nanosensor exhibits an excellent analytical performance on visual detection of 0.1–30 µM TC in human serum. Results of this study clearly indicate the feasibility of synthesis of B,N-GQDs derived from passion fruit juice for ultrasensitive tetracycline detection, which can open an avenue to use natural products for the preparation of environmentally benign and biocompatible carbon nanomaterials for highly sensitive detection of drugs, antibiotics, organic compounds and biomarkers. Full article

Dissolved oxygen (DO) is an important parameter to monitor in processes applicable in, for example, water technology and fermentation. In this study, we report the manufacturing of a membrane-less amperometric sensor that is based on the electrocatalytic reduction of oxygen. The sensor was tested in pH-neutral KNO₃ solutions and in a microbial fermentation to monitor the consumption of dissolved oxygen. The nitrogen and boron-doped reduced graphene oxide (N,B-HRGO) is used as an electrocatalyst for oxygen reduction. One step co-doping of nitrogen and boron on graphene oxide is performed using the hydrothermal method. The sensor responded linearly to the DO concentration. A sensitivity of 0.2 µA/mg·L⁻¹ O₂ is obtained for the DO concentration of 1.5 to 10 mg·L⁻¹ O₂. The membrane-less N,B-HRGO based DO sensor is successfully tested in an Amycolotopsis methanolica fermentation by monitoring the dissolved oxygen in real-time. The sensor detected the consumption of oxygen during the growth of A. methanolica, which shows the compatibility of N,B-HRGO as electrode material for amperometric measurement of dissolved oxygen in aerobic fermentation. This membrane-less amperometric sensor can be used to fabricate microdevices for microbioreactor applications. Full article

Spintronics is one of the most exciting applications of graphene-based devices. In this work Density Functional Theory is used to study a nanojunction consisting of two semi-infinite graphene electrodes contacted with an iron-porphyrin (FeP) molecule, which plays the role of spin filter for the incoming unpolarized electrons. The graphene-FeP contact closely resembles the recently synthesized porphyrin-decorated graphene [He et al., Nat. Chem. 2017, 9, 33–38]. The analysis of the spectral properties of the system shows a variation of the orbital occupancy with respect to the isolated FeP molecule and an hybridization with the delocalized states of the substrate, while the overall magnetic moment remains unchanged. Doping the electrodes with boron or nitrogen atoms induces a relevant rearrangement in the electronic structure of the junction. Upon B doping the current becomes significantly spin polarized, while N doping induces a marked Negative Differential Resistivity effect. We have also investigated the possible exploitation of the FeP junction as a gas sensor device. We demonstrate that the interaction of CO and O₂ molecules with the Fe atom, while being strong enough to be stable at room temperature (2.0 eV and 1.1 eV, respectively), induces only minor effects on the electronic properties of the junction. Interestingly, a quenching of the spin polarization of the current is observed in the B-doped system. Full article

Functionalized graphene derivatives including graphene oxide (GO), reduced graphene oxide (rGO), and heteroatom (nitrogen/sulphur (N/S) or boron (B))-doped graphene were used to synthesize composites with TiO₂ (T). The photocatalytic performance of composites was assessed for the degradation of Orange G dye (OG) under simulated solar light. All the prepared graphene derivatives—TiO₂ composites showed better photocatalytic performance than bare TiO₂. A higher photocatalytic activity was found for the composites containing GO and N/S co-doped rGO (k_app = 109.2 × 10⁻³ and 48.4 × 10⁻³ min⁻¹, for GO-T and rGONS-T, respectively). The influence of both initial solution pH and the reactive species involved in the OG degradation pathway were studied. The photocatalytic activity of the samples decreased with the increase of the initial pH (from 3.0 to 10.0) due to the occurrence of electrostatic repulsive forces between the photocatalysts surface and the molecules of OG, both negatively charged. The use of selective scavengers showed that although the photogenerated holes dominate the degradation mechanism, radicals and singlet oxygen also participate in the OG degradation pathway. In addition, reutilization experiments indicated that the samples were stable under the reaction conditions used. Full article