Search Results (31)

This study explores the development and optimization of TiO₂-based photoactive coatings enhanced with silver (Ag)—to boost photocatalytic performance—for application on glass-fiber-reinforced polyester (GFRP) and epoxy (GFRE) composites. The influence of Ag content on the structural, physicochemical, and functional properties of the coatings was evaluated. The TiO₂-Ag coating showed the best performance and was tested under UV-A irradiation and visible light (Vis), with high efficiency in VOC degradation, self-cleaning, and microbial activity. The tests were repeated in multiple runs, showing high reproducibility in the results obtained. In GFRP, pollutant and microorganism removal ratios of more than 90% were observed. In contrast, GFRE showed a lower adhesion and stability of the coating. This result is attributed to incompatibility problems with the epoxy matrix, which significantly limited its functional performance. The results highlight the feasibility of using the TiO₂-Ag coating on GFRP substrates, even under visible light. Under real-world conditions for 351 days, the coating on GFRP maintained its stability. This type of material has high potential for application in modular building systems using sandwich panels, as well as in facades and automotive components, where self-cleaning and contaminant-control properties are essential. Full article

A nitro-derivative of fenamic acid (4′–nitro–fenamic acid) was synthesized and used as ligand for the synthesis of four Co(II) complexes in the absence or presence of the N,N′-donors 2,2′–bipyridylamine, 1,10–phenanthroline and 2,9–dimethyl–1,10–phenanthroline. The characterization of the resultant complexes was performed with diverse techniques (elemental analysis, molar conductivity measurements, IR and UV-vis spectroscopy, single-crystal X-ray crystallography). The biological evaluation of the compounds encompassed (i) antioxidant activity via hydrogen peroxide (H₂O₂) reduction and free radical scavenging; (ii) antimicrobial screening against two Gram-positive and two Gram-negative bacterial strains; (iii) interactions with calf-thymus (CT) DNA; (iv) cleavage of supercoiled pBR322 plasmid DNA (pDNA), in the dark or under UVA/UVB/visible light irradiation; and (v) binding affinity towards bovine and human serum albumins. The antioxidant activity of the compounds against 2,2′–azinobis–(3–ethylbenzothiazoline–6–sulfonic acid) radicals and H₂O₂ is significant, especially in the case of H₂O₂. The complexes exhibit adequate antimicrobial activity against the strains tested. The complexes interact with CT DNA through intercalation with binding constants reaching a magnitude of 10⁶ M⁻¹. The compounds have a significantly enhanced pDNA-cleavage ability under irradiation, showing promising potential as photodynamic therapeutic agents. All compounds can bind tightly and reversibly to both albumins tested. Full article

Amazonian fruit residues like piquia shells are often discarded despite their antioxidant potential for sustainable cosmetic use. This study evaluated the photostability, phototoxicity, and photoprotection of hydroalcoholic piquia shell extract (PqSE) combined with UV filters in solutions and cosmetic formulations. PqSE formulations were photostable, even stabilizing photounstable UV filters. Phototoxicity tests (OECD TG 432) showed no phototoxic potential (MPE < 0.15) and reduction in the phototoxic potential of UV filters, while ocular irritation potential via HET-CAM assay indicated no irritant effects. The extract combined with UV filters enhanced protection against UVA-induced reactive oxygen species (ROS) production, achieving 60.9% effectiveness, outperforming commercial photostabilizers. Against UVB radiation, it showed cellular viability above 80%, comparable to benzophenone-3. PqSE formulations exhibited a radical protection factor (RPF) nine times higher than controls and reduced radical production by 64% after visible/near-infrared (VIS/NIR) irradiation on porcine skin, compared to 38% for controls. Confocal Raman microspectroscopy showed penetration depths below 12 µm for all time points. This study highlights the potential of reusing fruit residues like PqSE as sustainable, effective ingredients in sunscreen formulations, offering enhanced photoprotection and reduced environmental waste. Full article

Ivermectin (IVM) is a pharmaceutical antiparasitic agent with a broad range of medicinal properties that are comparable in impact to those of penicillin and aspirin. The molecule’s structural composition includes functional groups that indicate the potential for photoreactivity. However, there is a paucity of information regarding its photostability, particularly in tropical regions where parasitic diseases and intense solar radiation intersect. It would be beneficial to investigate the chemical transformation of this compound in a variety of natural aqueous environments under different irradiation sources. This knowledge gap motivated this study. Therefore, the chemical alterations of IVM were investigated in various natural aqueous media when exposed to solar radiation (UVA-Vis). In particular, an evaluation of its photostability was conducted at wavelengths of 350 and 254.5 nm. It is noteworthy that photodegradation occurred primarily at 350 nm. Additionally, IVM demonstrated photohemolytic effects on human erythrocytes, indicating phototoxicity. This suggests the presence of photoinduced mechanisms by this drug for the generation of free radicals, including singlet oxygen (¹O₂, type II mechanism), superoxide anion, and hydroxyl radical (^.O₂ and ^.OH, type I mechanism). The latter would also entail the interaction of the IVM molecule with the membrane of human red blood cells, which would signify a considerable biological impact. Furthermore, through computational calculations, potential photoproducts formed during IVM irradiation were deduced, simulating experimental conditions. Our findings contribute to an enhanced comprehension of IVM’s behavior under solar exposure, particularly in tropical contexts. Additional research is imperative to address its emerging biological activity status and potential implications for biomedical applications. Full article

This work examined the influence of UV-A light modulation on the photocatalytic process coadjuvated with H₂O₂ to mineralize phenol in an aqueous solution. A fixed-bed batch photocatalytic reactor with a flat-plate geometry, irradiated by UV-A LEDs, was employed. The successful deposition of commercial TiO₂ PC105 on a steel plate (SP) was achieved, and the structured photocatalyst was characterized using Raman spectroscopy, specific surface area (SSA) measurements, and UV–vis DRS analysis. These analyses confirmed the formation of a titania coating in the anatase phase with a bandgap energy of 3.25 eV. Various LED-dimming techniques, with both fixed and variable duty cycle values, were tested to evaluate the stability of the photocatalyst’s activity and the influence of operating parameters during the mineralization of 450 mL of a phenol solution. The optimal operating parameters were identified as an initial phenol concentration of 10 ppm, a hydrogen peroxide dosage of 0.208 g L⁻¹, and triangular variable duty cycle light modulation. Under these conditions, the highest apparent phenol degradation kinetic constant (0.39 min⁻¹) and the total mineralization were achieved. Finally, the energy consumption for mineralizing 90% phenol in one cubic meter of treated water was determined, showing the greatest energy savings with triangular light modulation. Full article

Silver nanoparticles (AgNPs) can be produced safely and greenly using water hyacinth, an invasive aquatic plant, as a reducing agent. This study aimed to optimize the UV-irradiation parameters for the synthesis of AgNPs from water hyacinth leaf extract. The study varied the reaction time and pH levels and added a stabilizing agent to the mixture. The synthesized AgNPs were characterized using UV-visible spectroscopy (UV-vis), transmission electron microscopy (TEM), X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), and inductively coupled plasma optical emission spectroscopy (ICP-OES). The findings revealed that the optimal conditions for synthesizing AgNPs were achieved by adjusting the pH level to 8.5, adding starch as a stabilizing agent, and exposing the mixture to UV-A radiation for one hour. These conditions resulted in the smallest size and highest quantity of AgNPs. Furthermore, the synthesized AgNP colloids remained stable for up to six months. This study highlights the potential of utilizing water hyacinth as a sustainable and cost-effective reducing agent for AgNP synthesis, with potential applications in pharmaceuticals, drug development, catalysis, and sensing detection. Full article

Solar radiation is the main risk factor for cSCC development, yet it is unclear whether the progression of cSCC is promoted by solar radiation in the same way as initial tumorigenesis. Additionally, the role of miRNAs, which exert crucial functions in various tumors, needs to be further elucidated in the context of cSCC progression and connection to solar radiation. Thus, we chronically irradiated five cSCC cell lines (Met-1, Met-4, SCC-12, SCC-13, SCL-II) with a custom-built irradiation device mimicking the solar spectrum (UVB, UVA, visible light (VIS), and near-infrared (IRA)). Subsequently, miRNA expression of 51 cancer-associated miRNAs was scrutinized using a flow cytometric multiplex quantification assay (FirePlex^®, Abcam). In total, nine miRNAs were differentially expressed in cell-type-specific as well as universal manners. miR-205-5p was the only miRNA downregulated after SSR-irradiation in agreement with previously gathered data in tissue samples. However, inhibition of miR-205-5p with an antagomir did not affect cell cycle, cell growth, apoptosis, or migration in vitro despite transient upregulation of oncogenic target genes after miR-205-5p knockdown. These results render miR-205-5p an unlikely intracellular effector in cSCC progression. Thus, effects on intercellular communication in cSCC or the simultaneous examination of complementary miRNA sets should be investigated. Full article

The DNA photocleavage effect of halogenated O-carbamoyl derivatives of 4-MeO-benzamidoxime under UVB and UVA irradiation was studied in order to identify the nature, position, and number of halogens on the carbamoyl moiety that ensure photoactivity. F, Cl, and Br-phenyl carbamate esters (PCME) exhibited activity with the p-Cl-phenyl derivative to show excellent photocleavage against pBR322 plasmid DNA. m-Cl-PCME has diminished activity, whereas the presence of two halogen atoms reduced DNA photocleavage. The substitution on the benzamidoxime scaffold was irrelevant to the activity. The mechanism of action indicated function in the absence of oxygen, probably via radicals derived from the N-O bond homolysis of the carbamates and in air via hydroxyl radicals and partially singlet oxygen. The UVA-vis area of absorption of the nitro-benzamidoxime p-Cl-PCMEs allowed for the investigation of their potential efficacy as photopesticides under UVA irradiation against the whitefly Bemisia tabaci, a major pest of numerous crops. The m-nitro derivative exhibited a moderate specificity against the adult population. Nymphs were not affected. The compound was inactive in the dark. This result may allow for the development of lead compounds for the control of agricultural insect pests that can cause significant economic damage in crop production. Full article

A photocatalyst comprised of Ag nanoparticles dispersed on an anatase matrix has been prepared using a simple hydrothermal method without additional thermal treatment. The prepared material was characterized using scanning electron microscopy (SEM), X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM), UV-Vis spectroscopy, and N₂ adsorption–desorption isotherms. The prepared catalyst activity was evaluated by photocatalytic degradation of C.I. Reactive Violet 2 (RV2) aqueous solution under UVA and visible light illumination. SEM revealed the non-uniform dispersion of silver particles throughout the matrix composed of fine particles. According to XRD analysis, the matrix was composed of pure anatase with a crystallite size of 8 nm calculated through the Scherrer equation. HRTEM micrograph analysis showed that anatase nanoparticles possess a spherical morphology and a narrow size distribution with an average particle size of 8 nm with more active anatase {100} crystal surface exposed, while silver nanoparticles were between 60 and 90 nm. A bandgap of 3.26 eV has been calculated on the basis of the DRS UV-Vis spectrum, while a specific surface area of 209 m²g⁻¹ has been established from adsorption isotherms. Thus, through a simple synthesis approach without subsequent thermal treatment, the agglomeration of nanoparticles and the reduction of specific surface area have been avoided. Prepared nano Ag/anatase photocatalyst exhibits excellent efficiency for the photodegradation of RV2 under UVA and visible irradiation. Full article

Water can trigger freeze–thaw cycles, acid rain corrosion, and microbial colonisation, all of which destroy stone. Water is one of the most influential factors in the destruction of outdoor stone heritage. Therefore, materials with excellent hydrophobic properties and durability are urgently required to effectively retard long-term stone weathering. In this study, two nanoparticles, TiO₂ and SiO₂, were used to modify dodecyltrimethoxysilane (DTMS), a waterproof coating commonly used for stone heritage protection, to fabricate nanocomposite superhydrophobic coatings. The micromorphology, water repellence (water contact angle and capillary water absorption), suitability to protect stone heritage (color change and water vapor permeability), and durability (thermal, light, and chemical stability) of DTMS and nanocomposite coatings were evaluated. The scanning electron microscope (SEM) images revealed that adding 0.5% (w/w) SiO₂ produced nanoscale roughness on the sandstone surface, leading to superhydrophobicity. The results of ultraviolet -visible (UV–Vis) spectrophotometer showed that adding 0.01% TiO₂ shielded more than 90% of UV light but accelerated the decrease in the contact angle under UVA irradiation. The addition of SiO₂ was able to avoid the detrimental effect of TiO₂ under UV light. The thermogravimetric analysis (TGA) results showed that both SiO₂ and TiO₂ nanoparticles improved the thermal stability of the coatings. In particular, the fabricated nanocomposite coating, SiO₂ and TiO₂ co-modified DTMS, had excellent water repellence, low color change and outstanding durability, and retained about 85% of the water vapor permeability of the stone, showing promise for stone protection. Full article

This work reports on a new TBO–Pluronic F–127 three-dimensional (3D) gel dosimeter for UV light dose distribution measurements. The optimal gel composition was found to be 60 µM Toluidine Blue O (TBO), which acts as a UV-sensitive compound; 5% w/w hydrogen peroxide (H₂O₂), which is necessary for initiation of TBO photodegradation and 25% w/w poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) (Pluronic F–127), which forms a physical gel matrix. The dosimeter becomes discoloured when exposed to UV radiation and a discolouration is the more intense, the higher the absorbed dose is. The samples after irradiation with UVA, UVB and UVC radiation were measured using UV-Vis spectrophotometry to obtain the basic dose–response characteristic of the dosimeter, including dose sensitivity, linear and dynamic dose range, threshold dose, stability over time and dose–response for fractioned and non-fractioned doses. Additionally, the TBO–Pluronic F–127 gel dosimeter was investigated for spatial stability and the ability to measure the dose distribution of UV radiation. The results obtained indicate that the TBO–Pluronic F–127 dosimeter is a promising UV sensor and 2D/3D UV dosimeter. Full article

4-chlorophenol (4-CP), a hydroxylated aromatic compound (HAC), is a recalcitrant and toxic organic pollutant found in industrial wastewater and various environmental media. In this paper, visible-light-activated photocatalysis using graphitic carbon nitride (GCN) was used to treat 4-CP in an aqueous media. Graphitic carbon nitride from different precursors (dicyanamide, urea, and melamine), as well as GCN/silver nanocomposites (AgBr, Ag₃PO₄, Ag₂CrO₄, and Ag), were successfully synthesized and characterized by BET, XRD, SEM, EDS, and UV-Vis DRS. The band gaps of the photocatalysts were estimated using the UV-Vis DRS characterization results and Tauc plots. The evaluation of the efficacy of the GCN-based catalysts in degrading 4-CP was conducted with different photoreactors such as a royal blue light-emitting diode (LED), a UV-A LED, LUZCHEM cool white lamps, and a solar simulator. The results showed that GCNs with royal blue LED can effectively degrade 4-CP from aqueous media. Among the different precursors, urea-derived GCN showed the best performance in degrading 4-CP due to its large surface area. GCN/0.3Ag₂CrO₄ nanocomposite showed a synergistic effect for the enhanced photocatalytic degradation of 4-CP. The degradation of 4-CP with a rate constant of 2.64 × 10⁻² min⁻¹ was achieved with a GCN/0.3Ag₂CrO₄ nanocomposite under royal blue LED irradiation. Full article

In this investigation, a hybrid-biocomposite “ZnO-Bentonite/Chitosan” was synthesized using inexpensive and environmentally friendly materials (Bentonitechitosan) and (ZnO). It was used as a photocatalyst for water remediation. The structural, optical, thermal, and morphological properties of the synthesized hybrid-biocomposite were investigated using XRD, FTIR spectroscopy, UV-vis diffuse reflectance spectroscopy, TGA, XPS, and SEM-EDS. The thermal measurements showed that the decomposition of CS was postponed progressively by adding PB and ZnO, and the thermal stability of the synthesized hybrid-biocomposite was improved. The characterization results highlighted strong interactions between the C–O, C=O, -NH₂, and OH groups of chitosan and the alumina-silica sheets of bentonite on the one side, and between the functional groups of chitosan (-NH₂, OH) and ZnO on the other side. The photocatalytic efficiency of the prepared hybrid-biocomposite was assessed in the presence of Methyl Orange (MO). The experiments carried out in the dark showed that the MO removal increased in the presence of Zn-PB/CS hybrid-biocomposite (86.1%) by comparison with PB (75.8%) and CS (65.4%) materials. The photocatalytic experiments carried out under visible light showed that the MO removal increased 268 times in the presence of Zn-PB/CS by comparison withZnO.The holes trapping experiments indicated that they are the main oxidative active species involved in the MO degradation under both UV-A and visible light irradiations. Full article

An environmentally friendlier solution processing has been introduced to fabricate zirconium oxide (ZrO₂) films on quartz substrates, using spin coating of simple water-based solution. The films cured with UV-A = 330 nm for different times (40, 80, 120 min) were investigated for structural and optical properties and compared with thermally annealed film (at 350 °C). XRD and Raman spectroscopy showed amorphous structure in all the samples with no significant phase transformation with UV-A exposure. AFM microscopy showed smooth and crack free films with surface roughness ≤2 nm that reduced with UV-A exposure. Ultraviolet-visible (UV–Vis) spectroscopy demonstrated optical transmittance ≥88% and energy band gap variations as 4.52–4.70 eV. Optical constants were found from spectroscopic ellipsometry (SE). The refractive index (n) values, measured at 470 nm increased from 1.73 to 2.74 as the UV-A exposure prolonged indicating densification and decreasing porosity of the films. The extinction coefficient k decreased from 0.32 to 0.19 indicating reduced optical losses in the films under the UV-A exposure. The photoluminescence (PL) spectra exhibited more pronounced UV emissions which grew intense with UV-A exposure thereby improving the film quality. It is concluded that UV-A irradiation can significantly enhance the optical properties of ZrO₂ films with minimal changes induced in the structure as compared to thermally treated film. Moreover, the present work indicates that water-based solution processing has the potential to produce high-quality ZrO₂ films for low cost and environmental friendlier technologies. The work also highlights the use of UV-A radiations as an alternate to high temperature thermal annealing for improved quality. Full article

The aim of the present study was to evaluate the relative attenuation of VIS, UV and NIR solar radiation through a large pond skylight into the interior of the l’Almoina Archaeological Museum (Valencia, Spain), and to determine how relative attenuation varied throughout the year and time of day. Measurements were taken at 9:00 a.m., 12:00 p.m. and 3:00 p.m. during July 2019 and January 2020. Relative attenuation values were obtained from the measurement of spectral irradiance in the exterior and at different points in the interior by means of two Ocean Optics spectrometers: HR4000CG-UV-NIR for VIS (400–700 nm) and NIR (700–1000 nm) bands, and FLAME-S-UV-VIS for UV-A (280–315 nm) and UV-A (315–400 nm) bands. The central points of the skylight had relative attenuation at 520 nm, reaching a value of 50% in summer at noon and 38% in the afternoon. At noon in winter, there were two relative attenuation peaks above 33% at 520 nm and at 900 nm. For mean relative attenuation, in the UVB range, the highest relative attenuation (20%) was inside the ruins in the morning in both summer and winter, and the UVA band relative attenuation was quite constant throughout the museum, but lower than that of the UVB band, in the range 0–3%. Full article