Search Results (6)

In this study, a statistical analysis of results reported in the literature was conducted through a 2ⁿ experimental design on the synthesis of bifunctional catalysts used in the production of lighter fuels, aiming for optimization while considering factors such as support (bentonite and vermiculite), acidity modifier (zirconium and cerium), metal (tungsten and molybdenum), metal content (5% and 10%), promoter (nickel and cobalt), and heteropolyacids (tungstophosphoric acid and molybdophosphoric acid), identifying their influence on textural properties and catalytic performance. Regarding the textural properties, vermiculite proved to be the most favorable support due to its high porosity. It was also established that the implemented metals impart positive characteristics to the catalysts due to their various properties; however, incorporating large amounts led to an adverse effect by clogging the pores. Catalytic performance was analyzed in isomerization and cracking reactions, which were enhanced by the use of cerium due to the presence of Brønsted acid sites and molybdenum for its stability. In this way, the statistical analysis conducted in this study was crucial for identifying the influence of key factors on the textural properties and catalytic performance of bifunctional catalysts. Using a 2ⁿ experimental design allowed for a systematic evaluation of variables reported in the literature, such as support, acidity modifiers, metals, metal content, promoters, and heteropolyacids. Full article

In this work, the microwave-assisted reaction of 5-hydroxymethylfurfural (5-HMF) into valuable ether and acylated production formation was investigated with the help of molybdophosphoric acid encapsulated dendritic fibrous silica (KCC-1) as a catalyst. XRD, N₂ adsorption-desorption, SEM, FT-IR, NH₃-TPD, and TEM were used to analyze the physicochemical and structural properties of the synthesized catalysts. The microwave etherification of 5-HMF with ethanol was tested using synthesized catalysts. The effects of the reaction temperature, reaction time, catalytic amount, and microwave power were investigated. The resulting MPA-KCC-1 and IMPA-KCC-1 catalysts demonstrated excellent activity for the etherification of 5-HMF with ethanol, producing 5-(hydroxymethyl) furfural diethyl acetal (HMFDEA) and 5-(ethoxymethyl)furfural diethyl acetal (EMFDEA) products selectively. The significant advantages of the work are the selective production of EMFDEA at 82%, the catalyst can be easily removed via filtration, and the catalyst activity remains nearly intact even after five reaction cycles. Full article

La-exchanged 12-tungstophosphoric acid (La_xTPA) and 12-molybdophosphoric acid (La_xMPA) salts (x = 0.25, 0.50, 0.75 and 1.00) were prepared via an ion exchange method. The physico-chemical characteristics of the materials were analyzed by using elemental analysis, X-ray diffraction (XRD), Fourier transformed infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), N₂-physical adsorption, X-ray photoelectron spectroscopy (XPS), and acidity-basicity measurements. The results indicated that La was introduced into the secondary structure of heteropolyacid (HPA) and have not influenced the primary structure, which effectively improved the surface area and pore size. Acidity-basicity studies indicated that incorporation of La resulted in a decrease in the number of acid sites and an increase in the number of basic sites. The catalytic activity of samples was studied in transesterification of glyceryl tributyrate with methanol and La_xTPA samples which exhibited high activity compared to La_xMPA samples due to having more active basic sites and a larger surface area. Calcined La_xTPA samples showed excellent stability, outstanding recyclability, and high activity for one pot transesterification and esterification processes. This outcome was attributed to the presence of balanced acidic and basic sites. Full article

A new prepared catalyst, 12-molybdophosphoric acid (HPMo) anchored to the mesoporous aluminosilicate AlSiM, synthesized from Amazon kaolin, was characterized and used as a heterogeneous acid catalyst for the production of eugenyl acetate by acetylation of eugenol with acetic anhydride. The effect of various reaction parameters, such as catalyst concentration, eugenol/acetic anhydride molar ratio, temperature and reaction time, was studied to optimize the conditions of maximum conversion of eugenol. The kinetics studies showed that in eugenol acetylation, the substrate concentration follows a first order kinetics. The results of activation energy was 19.96 kJ mol⁻¹ for HPMo anchored to AlSiM. The reuse of the catalyst was also studied and there was no loss of catalytic activity after four cycles of use (from 99.9% in the first cycle to 90% in the fifth cycle was confirmed), and an excellent stability of the material was observed. Based on catalytic and kinetic studies, HPMo anchored to AlSiM is considered an excellent catalyst. Full article

Cost-efficient and sustainable electrocatalysts for oxygen evolution reaction (OER) is highly desired in the search for clean and renewable energy sources. In this study, we develop a new one-step synthesis strategy of novel composites based on Ni and molybdenum carbide embedded in N- and P-dual doped carbon matrices using mainly chitosan biopolymer as the carbon and nitrogen source, and molybdophosphoric acid (HMoP) as the P and Mo precursor. Two composites have been investigated through annealing a mixture of Ni/chitosan and HMoP with two unlike carbon matrices, melamine and graphene oxide, at a high temperature. Both composites exhibit similar multi-active sites with high electrocatalytic activity for OER in an alkaline medium, which is comparable to the IrO₂ catalyst. For this study, an accurate measurement of the onset potential for O₂ evolution has been used by means of a rotating ring-disk electrode (RRDE). The use of this method allows confirming a better stability in the chitosan/graphene composite. This work serves as a promising approach for the conversion of feedstock and renewable chitosan into desired OER catalysts. Full article

The cobalt, manganese, and iron salts of tungstophosphoric or molybdophosphoric acid with growing content of metals were applied for the first time as catalysts in the Baeyer-Villiger (BV) oxidation of cyclohexanone to ε-caprolactone with molecular oxygen. The catalysts were characterized with Fourier transform infrared spectroscopy (FTIR), X-ray fluorescence (XRF), and ethanol decomposition reaction. Introduction of transition metals into the heteropoly structure increases the activity of resulting heteropoly salts in comparison with parent heteropolyacids. It was shown that the most active catalysts are salts of the heteropoly salts with one metal atom introduced and one proton left (HMPX) type, (where M = Co, Fe, Mn, and X = W, Mo) with the metal to proton ratio equal one. Among all of the studied catalysts, the highest catalytic activity was observed for HCoPW. The effect indicates that both the acidic and redox properties are required to achieve the best performance. The Baeyer-Villiger (BV) oxidation mechanism proposed identifies the participation of heteropoly compounds in three steps of the investigated reaction: oxidation of aldehyde to peracid (redox function), activation of carbonyl group (Lewis acidity), and decomposition of the Criegee adduct to ε-caprolactone (Brønsted acidity). Full article