Special Issue "Graphene-Polymer Composites III"

A special issue of Polymers (ISSN 2073-4360).

Deadline for manuscript submissions: 10 April 2021.

Special Issue Editors

Dr. Artur Pinto
Website
Guest Editor
Instituto de Investigação e Inovação em Saúde, Universidade do Porto, Rua Alfredo Allen, 208, 4200-135 Porto, Portugal
Interests: graphene-based materials; polymer composites; biomaterials; phototherapy; antibacterial materials; graphene inks
Special Issues and Collections in MDPI journals
Prof. Dr. Fernão D. Magalhães
Website SciProfiles
Guest Editor
LEPABE, Chemical Engineering Department, Faculty of Engineering, University of Porto, Portugal
Interests: synthetic and natural adhesives; lignocellulosic composites; high-performance industrial coatings; graphene-based biomaterials
Special Issues and Collections in MDPI journals

Special Issue Information

Dear Colleagues,

Further to the success of the Special Issue of PolymersGraphene-Polymer Composites II”, we are delighted to reopen the Special Issue, now entitled “Graphene-Polymer Composites III”.

The mechanical, electrical, thermal, magnetic, optical, and biological properties of graphene have attracted a significant amount of attention from the research community since the isolation of single-atom-thick graphene layers, by Geim and co-workers in 2004. Presenting a very high surface-to-volume ratio, relatively simple processability, and low cost, graphene and graphene-based materials (GBMs) were soon identified as promising nanofillers for polymer matrices. Reports have shown notorious property enhancements for graphene–polymer composites (GPC) at very low filler loadings. Uses of GPC in varied fields, such as energy, electronics, catalysis, separation and purification, biomedicine, aerospace, tribology, etc., have been demonstrated and, in some cases, put into industrial practice. However, challenges still exist. Platelet agglomeration within the polymer matrix is often seen to hinder performance improvements. Poor interfacial adhesion between filler and matrix is also a limiting factor in many systems, demanding tuning of the surface chemistry to promote physical or chemical interactions with the polymer chains. The range of routes for fabrication of GBMs, leading to different morphologies, oxidation states, and degrees of platelet exfoliation, has an impact on the final properties of the composites that has not yet been fully addressed. Some argue that the potential of graphene, and its advantages in relation to other nanofillers, has not yet been fully demonstrated for polymer composites. On the other hand, recent findings suggest that some graphene forms are potentially biodegradable and biocompatible, which constitutes a major advantage, compared for example with carbon black or some forms of carbon-nanotubes, which were demonstrated to be carcinogenic. Further studies are required, concerning not only GBMs’ biological properties, but also their potential applications in multiple fields.

This Special Issue invites original papers and reviews reporting on recent progress in the following areas:

  • Chemical and physical surface modifications of graphene and GBMs for improving dispersibility and compatibility with polymer matrices;
  • Fabrication methods of GPC in coating, film, bulk or particulate forms;
  • Properties of GPC (chemical, mechanical, thermal, electrical, magnetic, etc.);
  • Applications of GPC;
  • Biological properties of GBMs and GPC (biocompatibility, biointeractions, environmental toxicity, etc.).

It must be noted that the term “composite” should be understood here in its broader sense, describing a material, of any geometry and size, made of two or more constituent materials that do not lose their individual identities when combined.

Dr. Artur Pinto
Prof. Dr. Fernão D. Magalhães
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All papers will be peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Polymers is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 1800 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Graphene
  • Graphene oxide
  • Composites
  • Coatings
  • Adhesives
  • Fibers
  • Particles
  • Surface modification
  • Surface functionalization
  • Materials properties
  • Biological properties

Published Papers

This special issue is now open for submission.
Back to TopTop