Mechanical Properties of Hybrid Structures Incorporating Nano-Silica and Basalt Fiber Pellets

: Recently, developing a nonferrous reinforcement system (corrosion-free system) using durable and ductile cement-based materials that incorporate discrete ﬁbers has been a promising option for exposed concrete structures in cold regions or marine environments. Therefore, in this study, properties of a novel type of cementitious composite comprising nano-silica and a high dosage of slag were investigated. The hybrid (layered) composites assessed in this study were composed of two layers of different types of cementitious composites. Normal concrete (NC) was used in the top layer combined with a layer of ﬁber-reinforced cementitious composite (FRCC) reinforced with either the recently developed basalt ﬁber (BF) pellets (basalt ﬁber strands encapsulated by a polymeric resin or steel ﬁbers (SF)) that were used at different dosages. The post-cracking behavior in terms of residual strength, residual index, and toughness are presented and discussed. The analysis of results showed the effectiveness of the BF pellets in enhancing the post-cracking behavior of specimens, as they behaved comparably to counterpart specimens comprising SF, which makes them a good candidate for infrastructural applications including rehabilitation such as new bridge girders or overlays.


Introduction
Concrete often cracks due to its limited tensile and deformation capacity. The presence of cracks may not only affect the aesthetics of structures, but also its durability by allowing the infiltration of moisture and oxygen causing corrosion of the reinforcing steel accompanied by a deterioration of the concrete [1]. In addition, the presence of de-icing salts and repeated freezing-thawing cycles in cold regions aggravate the damage of concrete. Therefore, to expand the possibilities of using concrete in such harsh environments, developing high performance mortar/composite and concrete to rehabilitate concrete infrastructure (e.g., bridge decks, pavements, parking structures) is much needed [2].
In this context, the use of a fiber-reinforced cementitious composite (FRCC) has been suggested by many researchers to enhance short-term structural performance. Incorporating discrete fibers into any cementitious composite (e.g., geopolymer mortar) can reduce bleeding, controlling shrinkage cracking, and improving impact resistance [3]. Furthermore, the most pronounced advantages of using fibers in cementitious composites are increasing their energy absorbing capacity, deformation capability, and load bearing capacity after cracking due to the ability of the fibers to bridge cracks and to transfer tensile stress across the crack interface [4]. In addition, incorporating waste materials along with short fibers significantly enhanced the mechanical properties [5].
The application of discrete fibers mainly contributes to the improvement of FRCC tensile properties [6]. However, previous studies showed that the contribution of fibers in enhancing the compressive strength is insignificant. Accordingly, it is reasonable and more on economical to implement fibers in structural members on the tension side only to cast layered (hybrid) structures. For example, a simply supported beam under flexural service loads is subjected to tension on the bottom side and compression on the top side. Applying the FRCC as a layer in the tension side of such a beam could significantly improve the post-cracking flexural capacity, while using the fibers in the compression zone would contribute less [7].
Various commercially available fibers can be used to make fiber-reinforced cementitious composites, such as steel and synthetic, organic, and inorganic fibers. However, relatively new types of fibers manufactured from basalt rocks are progressively emerging in civil engineering research, including a special type of basalt fiber (BF) pellets, which are made of basalt fibers encapsulated by polyamide or other resins. The production process of basalt fibers is more environmentally friendly, and it is cheaper in comparison to other types of fibers such as glass fibers. In addition, basalt fibers have high tensile strength, and they are not vulnerable to corrosion in contrast to the corrodible steel fibers that result in rough concrete surfaces, which should be avoided in applications such as slabs on the ground, bridge decks, and pavements [8][9][10][11][12].
Despite the advantages of fibers, it was reported that adding fibers in mortar or concrete may increase its permeability due to the formation of numerous weak interfacial transition zones (ITZ) between the fibers and cementitious matrix. In addition, the efficacy of fiber reinforcement depends upon the matrix composition [4,[13][14][15][16].
Therefore, producing a cementitious composite with superior properties is crucial, which can be obtained by incorporating supplementary cementitious materials (SCMs), such as silica fume and/or ground granulated blast-furnace slag. These supplementary materials can react with calcium hydroxide crystals, the weakest by-product of the cement hydration reaction, to form more calcium silicate hydrate (CSH), which is the backbone of concrete strength and binding. This results in a refined and denser microstructure and ITZ. Nevertheless, it is worth noting that slag is a latent hydraulic binder which mainly contributes to improving the long-term performance of cementitious systems and incorporating high dosages of slag usually leads to a delay in hardening and strength as well as microstructural development during the early ages [17,18]. In addition, it is well-documented that adding a small dosage of nanoparticles (e.g., nano-silica, NS) can vigorously speed up the kinetics of cement hydration, especially during the early ages, besides their contribution to improving the microstructural development of cement-based materials [17,[19][20][21].
This study presents part of an ongoing program at the University of Manitoba. The first phase of this project was undertaken by Mahmoud et al. [12], who investigated the behavior of high-strength nano-modified cementitious composites incorporating 6% NS with 40% slag and reinforced with BF pellets (BFRCC) in terms of compressive strength, flexural strength, and toughness. The slag replacement level (40 %) was selected to meet the requirements of the category HVSCM-2 for high SCM concretes according to CSA A23.1/A23.2-19 (Annex K) [22]. It was concluded that this BFRCC had high performance and potential to be applied in structural applications. Yet, some research gaps and limitations still exist and need to be addressed to fully exploit this innovative composite (BFRCC) in infrastructure applications. For instance, only one dosage of BF pellets was used in the previous study by Mahmoud et al. [12], and the results were not compared with composites incorporating steel fibers (SF), which are currently the most used fibers in the construction industry. In addition, the concept of layered structures (hybrid structures) was not applied. These trends have not been substantiated by systematic research work.
This study provides much better understanding and fundamental data about these composites for achieving improved performance of structural elements incorporating BFRCC. The fresh, hardened, and durability properties of these composites were evaluated.

Materials
General use (GU) cement and slag, which meets the requirements of CSA-A3001 [23], were used as the main components of the binder. Table 1 shows the chemical and physical properties of these main components. In addition, a commercial nano-silica (NS) sol was added in the binder. Fine aggregate, having a fineness modulus of 2.9 and a gradation less than 600 µm according to ASTM C136 [24], was adopted to cast the composites. The specific gravity and absorption of the fine aggregate were 2.6 and 1.5%, respectively, according to ASTM C128 [25]. A high-range water-reducing admixture (HRWRA) complying with ASTM C494 Type F [26] was used to target a flow between 185 and 215 mm for all composites. The cementitious composites were reinforced with either BF pellets or steel fibers ( Figure 1). The BF pellets were made of 16-micron basalt roving encapsulated by polyamide resin, and the BF represented 60% of the pellet by weight. The BF pellets were 36 mm long with a diameter of 1.8 mm. Hooked-end steel fibers with a diameter of 0.5 and 30 mm in length were also used. The properties of the BF pellets and the steel fibers are listed in Table 2. with ASTM C494 Type F [26] was used to target a flow between 185 and 215 mm for all composites. The cementitious composites were reinforced with either BF pellets or steel fibers ( Figure 1). The BF pellets were made of 16-micron basalt roving encapsulated by polyamide resin, and the BF represented 60% of the pellet by weight. The BF pellets were 36 mm long with a diameter of 1.8 mm. Hooked-end steel fibers with a diameter of 0.5 and 30 mm in length were also used. The properties of the BF pellets and the steel fibers are listed in Table 2.

Proportions and Mixing Procedues
For the FRCC layer on the tension face of the specimens, two mixtures were cast: normal cementitious composite (designated as N) and high-performance cementitious composite (designated as H). Further description of the components of the N and H mixtures can be found elsewhere [27]. The mixtures were reinforced with BF pellets and SF. The rationale to select the dosages of fiber is illustrated by the authors elsewhere. The reference composite was cast with the same ingredients but without fibers. Table 3 shows the proportions of all mixtures. For the mixture nomenclature, the first letter illustrates the type of the cementitious composite ("N" for normal mixture and "H" for high-performance mixture), whereas the second letter refers to the type of fiber ("B" for basalt fiber pellet and "S" for steel fiber). The third part (number) illustrates the dosage of fibers. The base concrete was cast to satisfy the requirements specified by the City of Winnipeg (COW), Manitoba, Canada, for structural concrete projects. The COW has specified concrete with a target compressive strength of 35 MPa at 28 days meeting an exposure Class C-1 and comprising synthetic fibers with a minimum post-residual cracking index of 0.15 at 7 days.

Tests
Two tests were conducted to assess the effect of varying the dosages of BF pellets and incorporating SCMs on the fresh properties of the mixtures. The consistency of the mixtures was performed using the truncated cone and flow table method according to ASTM C230/C230M [28] and ASTM C1437 [29]. The mortar flow loss test, lasting up to 60 min, was also conducted according to the latter standards.
To evaluate the hardened properties of the composites, the compressive strength, and flexural strength, pull-off tests were performed. To determine the compressive strength of the mixtures, triplicate cylinders (100 mm × 200 mm) were tested at different ages according to ASTM C39 [30]. Since one of the main challenges with the layered structures is the interaction and bond between the materials, duplicate concrete slabs of 250 mm × 250 mm surface area and 100 mm thickness were cast for each mixture following the same procedures mentioned earlier. After casting, the slabs were demolded and moist cured for 28 days in the curing room, then the slabs were partially cored to determine the pull-off strength according to ASTM C1583 [31].
To determine the flexural strength of the composites, triplicate standard prisms (100 mm × 100 mm × 350 mm) were tested according to ASTM C1609 [32]. A closed loop testing machine (Figure 2) was used to apply the load, where the deflection rate was controlled by the measured net mid-span deflection of the prism. The residual strength at net deflection of ( /600) and ( /150) was calculated based on Equation (1): where, f is the strength (MPa), P is the load (N), is the span length (mm), b is the average width of the specimen at the fracture, as oriented for testing (mm), and d is the average depth of the specimen at the fracture, as oriented for testing (mm). In addition, the toughness herein was calculated following the ASTM C1609 [32] as the area under the load-deflection curve up to a displacement of /150 (i.e., 2 mm for the prism size used).
In addition, the residual post-cracking strength index (R i ) was calculated according to Equation (2): R i = ((P 0.5 + P 0.75 + P 1.0 + P 1.25 )/4)/P cr (2) where, P 0.5 , P 0.75 , P 1.0 , and P 1.25 are the residual loads at deflections of 0.5, 0.75, 1.0, and 1.25 mm, and P cr is the peak load at first cracking.
tion of (ℓ/600) and (ℓ/150) was calculated based on Equation (1): where, f is the strength (MPa), P is the load (N), ℓ is the span length (mm), width of the specimen at the fracture, as oriented for testing (mm), and d depth of the specimen at the fracture, as oriented for testing (mm). In addi ness herein was calculated following the ASTM C1609 [32] as the area u deflection curve up to a displacement of ℓ/150 (i.e., 2 mm for the prism si dition, the residual post-cracking strength index (Ri) was calculated accord (  The interconnectivity of the pore system of the composites was assess chloride penetration test (RCPT) according to ASTM C1202 [33]. During th h), 60 V DC was applied to the cell compartments. The standard describe RCPT in terms of passing charges through concrete that are continuously termine the penetrability class according to ASTM C1202. Since physical ob vide a better representation of the penetrability of chloride ions only in physical penetration depth of chloride ions was measured in this study im the completion of the test by spraying 0.1 M AgNo3 (silver nitrate) solutio face of equally split discs. The discs were allowed to set under fluoresce proximately 15 min to obtain the whitish precipitate of silver chloride [34 To complement the findings of the hardened properties, scanning e copy (SEM) was employed on fracture pieces to assess the morphology o and to evaluate their characteristics in the cementitious matrix. The small p were coated with carbon (thickness ranging from 50 nm to 500 Angstroms conductivity for the SCM.

Flowability
The flowability is the resulting increase in average base diameter of th expressed as a percentage of the original base diameter, Do = 100 mm in  The interconnectivity of the pore system of the composites was assessed by the rapid chloride penetration test (RCPT) according to ASTM C1202 [33]. During the test period (6 h), 60 V DC was applied to the cell compartments. The standard describes the data from RCPT in terms of passing charges through concrete that are continuously recorded to determine the penetrability class according to ASTM C1202. Since physical observations provide a better representation of the penetrability of chloride ions only into concrete, the physical penetration depth of chloride ions was measured in this study immediately after the completion of the test by spraying 0.1 M AgNo 3 (silver nitrate) solution onto the surface of equally split discs. The discs were allowed to set under fluorescent light for approximately 15 min to obtain the whitish precipitate of silver chloride [34].
To complement the findings of the hardened properties, scanning electron microscopy (SEM) was employed on fracture pieces to assess the morphology of the BF pellets and to evaluate their characteristics in the cementitious matrix. The small pea-sized pieces were coated with carbon (thickness ranging from 50 nm to 500 Angstroms) to enhance the conductivity for the SCM.

Flowability
The flowability is the resulting increase in average base diameter of the mortar mass, expressed as a percentage of the original base diameter, D o = 100 mm in this study. The flow is the increase in average base diameter, expressed in mm. The flow loss is the loss of workability with time, expressed in mm. The flow, flowability, flow loss of the fresh cementitious composite mixtures with and without fibers are given in Table 4. The results illustrate the variation in the slump flow of composites reinforced with different dosages of BF pellets or SF. It is worth mentioning that the dosage of the superplasticizer was added at a constant dosage for the same type of the cementitious composite (see Table 3) to magnify the effect of adding fibers on the flowability of composites. All mixtures achieved a slump flow of 200 ± 20 mm (flowability of 100 ± 20%), which is reaching the threshold of treating the composite as self-consolidating concrete of approximately 230 mm according to the CSA A23.1/CSA A23.2-19 [22], and the recommendation stipulated by Hunger [35]. The incorporation of SCMs such as slag and nano-silica required a greater dosage of superplasticizer to achieve the desired level of workability (see Table 3). This can be attributed to the slag which had a highly angular shape and rough surface texture [36], in addition to the high specific surface area-to-volume ratio of the NS. Furthermore, it can be observed that the addition of BF pellets or SF had a negative effect on the workability, regardless the type of the cementitious composite. For example, adding 4.5% of BF pellets in both mixtures N-B-4.5 and H-B-4.5 reduced the flowability by 10 and 7%, respectively, compared to that of the counterpart specimens prepared without fibers. This can be attributed to the fact that the addition of fibers offered higher shear resistance to flow, which resulted in decreased flowability and stiffer fresh composites [37]. Moreover, increasing the dosage of the basalt fiber pellets was associated with a consistent reduction in the flowability of the cementitious composite. For instance, increasing the number of pellets from 2.5% in N-B-2.5 and H-B-2.5 to 6.9% in N-B-6.9 and H-B-6.9, respectively, led to an 11 and 8% reduction in the flow values. This might be due to increased surface area associated with the increase of fiber content. Compared to the control mixtures (N-X-0.0 and H-X-0.0), the addition of 1.0% of steel fibers yielded a noticeable decrease in the flowability of 20 and 16%, respectively. This can be attributed to the higher shear resistance to the flow of the composite offered by the metallic deformed fibers with relatively high modulus. These trends were similar to those reported by Yu et al. [38] and Wu et al. [39]. Moreover, irrespective of the type of the composite or the dosage of the pellets, all mixtures maintained reasonable flow up to 30 min after mixing, as the average flow loss was approximately 15% of the initial flow. After 60 min, the mixtures maintained almost 69% of their initial values. These results emphasize the applicability of using such composites in the field in terms of moldability/placement and finishability operations since it possessed suitable flow properties.

Compressive Strength
The average compressive strength for the developed composites obtained from cylinders at different ages is listed in Table 5. As evident by the compressive strength results, the addition of NS along with slag showed significantly more effect on the strength development, especially at early ages when it is compared to the corresponding reference mixture with cement only, regardless the type or dosage of the fibers. For example, the average compressive strength of the nano-modified slag-based composites was significantly increased by 97 and 48% at 3 and 7 days, respectively, compared to those of the reference cement-based specimens. The results were assessed by the analysis of variance (ANOVA) to determine whether there were any statistically significant differences between the means of compressive strength, as shown in Table 6. The t-test looked at the t-statistic, t-distribution, and degrees of freedom to determine a p value (probability) that could be used to determine whether the population means differ. The t-test is one of several hypothesis tests. To compare three or more variables, statisticians use the analysis of variance (ANOVA). If the sample size is large, statisticians use a z-test. In addition, the authors have used ANOVA in their previous research rather than other statistical analyses that dealt with more than two variables. According to Montgomery [40], exceeding the F cr value of an F distribution density function indicates that the variable tested has a significant effect on the average results. The significant effect of incorporating SCMs was statistically supported by ANVOA for the compressive strength results at 3 and 7 days, since adding slag and NS yielded F values of 64.0 and 15.2, which were greater than the F cr of 5.3. On the other hand, the latter strength development started to diminish at higher curing ages especially at 54 and 91 days, as the average compressive strengths of the H composites slightly increased by 20 and 14%, respectively, with respect to the N composites. The reason behind the increasing values of compressive strength with time for the N composites was the progression of the hydration process, especially with the high volume of cement adopted in this study (700 kg/m 3 ). This was statistically supported by the ANOVA for the compressive strength results at 56 and 91 days, as the incorporation of SCMs yielded F values of 2.8 and 2.1, which were less than the F cr of 5.3, indicating that the effect of this parameter was statistically insignificant at later ages.   The effect of fiber inclusion on the compressive strength of concrete is controversial [41][42][43], as BFRCC at different dosages showed lower compressive strengths, compared to the control mixtures without fibers (N-X-0.0 and H-X-0.0). A similar trend was obtained by Branston et al. 2016 [43] for BF mini bars. The ANOVA showed that incorporating the BF pellets in the N and H matrices yielded an F value of 6.0, which was higher than the critical value (F cr ) of 4.1, indicating that the effect of adding such fibers on the compressive strength was statistically significant. For example, the 28-day compressive strength was markedly reduced by 17 and 25% and 26 and 32.5 %, when the composite was reinforced with BF pellets at dosages of 4.5 and 6.9% for the N and H composites, respectively. This may be attributed to the formation of additional interfacial transitional zones (ITZs) in the matrix, and the reduced workability, which causes more air to be entrapped in the cementitious matrix after compacting, as previously observed by Mahmoud et al. [12]. In this context, varying the dosage of BF pellets from 2.5 to 6.9% led to a 16 and 22% decrease in the compressive strength value for the N and H composites, respectively. In addition, the ANOVA results revealed significant differences among the compressive strength results for the mixtures incorporating different dosages of BF pellets. For instance, increasing the dosage of BF pellets from 2.5 to 6.9 % in both composites had an F value of 8.0 compared to an F cr of 4.4.
On the other hand, unlike the BF pellets, the incorporation of steel fibers showed a slight increase in the compressive strength quantitatively with respect to the two control mixtures. This was statistically supported by ANOVA for the compressive strength results, as adding SF yielded an F value of 0.2, which was less than the F cr of 4.4. This insignificant effect might be ascribed to the small volumes of SF introduced to the cementitious matrix, as the dosage of the SF corresponded to the lowest dosage in the BF. Nevertheless, the failure mode was considerably altered from brittle to ductile, as the bridging effect of the fibers maintained the integrity of the cylinders up to the end of the test, as depicted in Figure 3. It is worth noting that the compressive strength was marginally affected by the properties of fibers (modulus of elasticity and aspect ratio). The incorporation of fibers, regardless of the fiber type, usually contributes to increasing air bubbles in the matrix, and thus, reducing its strength [44,45]. This was confirmed by ANOVA for the compressive strength results, as replacing the BF pellets with steel fibers in the N and H composites yielded F values of 2.5 and 3.6, which were smaller than the F cr value of 4.4 (Table 6). This trend is highlighting the predominant role of the cementitious matrix in cantly reducing/increasing the compressive strength, rather than the type of fiber lets or SF). In addition, when the volume was kept constant, the same observa This trend is highlighting the predominant role of the cementitious matrix in significantly reducing/increasing the compressive strength, rather than the type of fiber (BF pellets or SF). In addition, when the volume was kept constant, the same observation was found; replacing 2.5 % of BF pellets with 1.0% SF yielded an F value of 2.2, which is less than the F cr value of 4.4.

Flexural Strength and Toughness
The flexural and residual strength, as well as toughness and residual post-cracking strength index (R i ), for all mixtures at 28 days are listed in Table 7. In general, complying with the compressive strength results, the H composites were supposed to have an improved pre-cracking performance in terms of the first-peak strength, despite the fibers type or dosage included, in comparison to that of the counterpart specimens without slag and nano-silica (N composites). However, unexpectedly, the incorporation of SCMs did not significantly affect the first-peak strength, as the trends of both the N and H composites were quite comparable (see Table 7). This was due to the N composites being made with a high-volume cement (700 kg/m 3 ) in addition to the continual curing up to 28 days, which resulted in significant increase in its strength. These strengths, which exceeded the limit that defines the high strength concrete with 55 MPa [46], were similar to the strength of the H composites at 28 days (see Table 5). This was statistically supported by the ANOVA for the first-peak strength at 28 days, as changing the cementitious composites from N to H yielded F value of 3.8, which was less than the F cr of 4.2, indicating that the effect of this parameter on the pre-peak stage was statistically insignificant. Consistently, the fibers had marginal effect on the behavior during the pre-cracking stage, which was mainly dependent on the properties of the cementitious matrix. The first-crack strength (first-peak strength) for all fiber-reinforced composites (N and H composites) with either BF or SFs, showed comparable values with respect to the control mixture without fibers. This trend was statistically substantiated by the ANOVA results, as incorporating the BF pellets in the N and H matrices yielded an F value of 0.4, which was less than the critical value (F cr ) of 4.2, indicating that the effect of adding such fibers on the first-crack strength was statistically insignificant. Similarly, replacing the BF pellets with SF did not show any distinctive difference in terms of the first-crack strength, even if the modular ratio and the volume were kept constant; such insignificant effect was also validated by the ANOVA results (see Table 6). This behavior may be explained as follows. At the pre-cracking stage, although both the fiber and the cementitious matrix sustained loads together, the relatively low stress resulted in similar bond stress for the BFRCC and SFRCC with different fiber contents; however, after cracking, only fibers sustained loads through different mechanisms.
The P-δ (load-deflection) curves for all test prisms are shown in Figure 4. The reported mid-span deflection represents the average readings from two LVDTs that were in contact with a bracket attached to each specimen. As expected, the prism made without any fibers did not show any significant residual strength after cracking and broke in a brittle manner, and the sudden drop in the load after reaching the peak was observed due to the presence of synthetic fibers in the top layer. Whereas all FRCC prisms, irrespective of the type or dosages of fibers added to the mixture, exhibited improved post-cracking behavior due to deformation and pull-out mechanisms of the BF pellets and the SF.  The P-δ curves are usually used qualitatively to examine the overall performan the various FRCC. However, to quantitatively evaluate the behaviour of FRCC, two niques were adopted: the toughness and the residual index. First, despite the min effect of the SCMs on the pre-cracking stage, the incorporation of slag and nanocontributed to improving the post-cracking behaviour with statistical significance ( 6). For example, replacing 40% cement content with slag and adding 6% NS increase average toughness and residual index for all mixtures by 45 and 42%, respectively spective of the type or dosage of fiber. This behavior may be attributable to the h degree of hydration and improved quality of the ITZ between the fibers and cement  After the first cracking, the prisms did not fail but continued to carry either decreasing loads (N-B-2.5, N-B-4.5, N-B-6.9, N-S-1.0, H-B-2.5, and H-S-1.0) or increasing loads (H-B-4.5 or H-B-6.9). The post-cracking behavior of the former prisms was associated with a sudden drop (an average drop of 30% at approximately 0.2 mm deflection) in the load. However, the fibers in these prisms were able to control the crack exhibiting a notable increase in composite fracture resistance, which was accompanied by a slight increase in load carrying capacity but not exceeding the initial cracking load. As for the later prisms, no drop in the load was observed, but it continued to carry increasing loads, whereas the peak load of the composite was notably greater than that of the load at the first cracking. The prisms reinforced with high dosages of BF pellets (H-B-4.5 and H-B-6.9) exhibited a pseudo strain hardening behavior, similar to Engineered Cementitious Composites, which nearly behave as ductile metals [47]. The prisms from H-B-4.5 and H-B-6.9 achieved the highest post-cracking behavior, as the residual strengths at a deflection of 0.5 mm (span/600) were approximately 18 and 27% higher than the first crack strength of both mixtures, respectively. At a deflection of 2 mm (span/150), these percentages were approximately 15 and 21% for both mixtures, respectively. Such distinctive behavior beyond the first cracking for both mixtures (B-4.5 and B-6.9) substantiates the well-documented notion that effective types of fibers are mainly incorporated to significantly enhance the flexural behaviour [4]. This trend might be attributed to the adequate distribution of BF pellets over the cross-section of the layer and the intensity of fibers, which improved their effectiveness in controlling crack propagation in the matrix by redistributing micro-cracks ( Figure 5). In addition, the improved bonding with the cementitious matrix resulted in the gradual pull-out failure rather than the rupture of the pellets, as was substantiated by the SEM. In the same context, the Ri results of the N and H composites contai or SF have remained above the level (0 -0.3) specified by the Canadian H Design Code, CHBDC [48] based on the application and the number of di ventional cracking control reinforcement, to be adequate for an efficient pos formance. For instance, the incorporation of 4.5% BF pellets in the N and yielded Ri values of 0.94 and 1.1, respectively, compared to that of the co tures prepared without fibers, which were 0.1 and 0.2, respectively. Albei had lower modulus of elasticity and aspect ratio with respect to the SF, a cracking behavior was observed for both cementitious composites in ter strength at both deflections (ℓ/600 and ℓ/150), residual index, and fracture ness). To keep the ratio of volume of BF pellets to SF equal to the modular r ness was markedly increased. For instance, replacing 1.0% of SF with 6.9 both cementitious composites (N-B-6.9 and H-B-6.9) led to a significant inc The P-δ curves are usually used qualitatively to examine the overall performance of the various FRCC. However, to quantitatively evaluate the behaviour of FRCC, two techniques were adopted: the toughness and the residual index. First, despite the minimal effect of the SCMs on the pre-cracking stage, the incorporation of slag and nano-silica contributed to improving the post-cracking behaviour with statistical significance (Table 6). For example, replacing 40% cement content with slag and adding 6% NS increased the average toughness and residual index for all mixtures by 45 and 42%, respectively, irrespective of the type or dosage of fiber. This behavior may be attributable to the higher degree of hydration and improved quality of the ITZ between the fibers and cement paste due to the process by which the load is transferred from the cementitious matrix to the fibers to bridge the cracks.
In the same context, the Ri results of the N and H composites containing BF pellets or SF have remained above the level (0-0.3) specified by the Canadian Highway Bridge Design Code, CHBDC [48] based on the application and the number of directions of conventional cracking control reinforcement, to be adequate for an efficient post-cracking performance. For instance, the incorporation of 4.5% BF pellets in the N and H composites yielded R i values of 0.94 and 1.1, respectively, compared to that of the counterpart mixtures prepared without fibers, which were 0.1 and 0.2, respectively. Albeit the BF pellets had lower modulus of elasticity and aspect ratio with respect to the SF, a superior post-cracking behavior was observed for both cementitious composites in terms of residual strength at both deflections ( /600 and /150), residual index, and fracture energy (toughness). To keep the ratio of volume of BF pellets to SF equal to the modular ratio, the toughness was markedly increased. For instance, replacing 1.0% of SF with 6.9% BF pellets in both cementitious composites (N-B-6.9 and H-B-6.9) led to a significant increase of 42 and 15%, respectively, in the toughness, which was also confirmed by the ANOVA results (see Table 6). Interestingly, when the volume of both fibers was kept constant, taking into consideration the superior properties of SF with respect to the BF pellets, the post-cracking behavior was quite comparable, as shown in Figure 4. Accordingly, replacing 2.5% BF pellets with 1.0% SF had an insignificant effect on the toughness results. This trend was also substantiated by the ANOVA results, as incorporating the same volume of both types into the matrix yielded an F value of 0.06, which was much lower than the critical value (F cr ) of 5.0. This may be ascribed to the enhanced bonding of the cementitious composite within the textured grooves in the longitudinal direction of the BF pellets, which provided a host for the deposition of the hydration products, as shown in Figure 6. To assess the effectiveness of incorporating the FRCC as a layer, not over the whole cross-section, on improving the post-cracking behaviour, additional sets of prisms were cast and tested following the guidelines of ASTM C1609 [32].

R REVIEW 13
The whole cross-section of the specimens was cast using the H cementitious composites and was reinforced with BF pellets at different dosages of 2.5, 4.5, and 6.9%. To differentiate the nomenclature of the full depth specimens from the layered specimens, a letter F preceded the full depth specimen's name. Table 8 lists the flexural strength parameters for the full depth specimens at 28 days, based on the load-deflection curve shown in Figure 7. At a fixed fiber dosage, the toughness of the layered specimens was slightly lower than that of their full depth counterparts. The ANOVA results revealed insignificant differences among the toughness calculations for the layered and full depth prisms. For example, incorporating 4.5% BF pellets over the whole depth of the prism had an F value of 3.2 compared to an Fcr of 7.7 (Table 6). This may be ascribed to the well- To assess the effectiveness of incorporating the FRCC as a layer, not over the whole cross-section, on improving the post-cracking behaviour, additional sets of prisms were cast and tested following the guidelines of ASTM C1609 [32].
The whole cross-section of the specimens was cast using the H cementitious composites and was reinforced with BF pellets at different dosages of 2.5, 4.5, and 6.9%. To differentiate the nomenclature of the full depth specimens from the layered specimens, a letter F preceded the full depth specimen's name. Table 8 lists the flexural strength parameters for the full depth specimens at 28 days, based on the load-deflection curve shown in Figure 7. At a fixed fiber dosage, the toughness of the layered specimens was slightly lower than that of their full depth counterparts. The ANOVA results revealed insignificant differences among the toughness calculations for the layered and full depth prisms. For example, incorporating 4.5% BF pellets over the whole depth of the prism had an F value of 3.2 compared to an F cr of 7.7 (Table 6). This may be ascribed to the well-documented trend that the contribution of fibers to enhance compressive strength is negligible, and these findings support the authors' notion that it is more economical and effective in practice to incorporate the FRCC as a layer in the tension side only. Table 8. Mechanical properties of the full depth specimens at 28 days.

Bond Strength
There has been an increasing demand to optimize the structural element, and be achieved by combining two different materials. Such composite structures ar named as a layered or hybrid structure, where the interaction and bond between ferent materials are considered as a major challenge for design engineers, as bond is a critical cause of deterioration in layered structures. Therefore, the pull-off t adopted to evaluate the monolithic behaviour between the FRCC layer with base the concrete and capture the risk results from the incompatibility between the two It is worth mentioning that the specimens in the pull-off test are subjected to pure stresses, which represents a severe scenario for the specimen.
The average bond strength values obtained from eight cores for each mixtu days are shown in Figure 8. The results showed that the mixtures prepared witho fibers (N-X-0.0 and H-X-0.0) had a bond strength of 1.44 and 2.2 MPa, respectivel mixtures experienced an undesirable mode of failure, as the failure occurred mainl composite itself, as shown in Figure 9. This may be ascribed to the N and H com prepared without any fibers, which had tensile strength lower than that of the ba crete, the bond line between the two layers or the epoxy used to bond the steel disk pared to the control mixture N-X-0.0, there was a slight improvement in the bond s of the H-X-0.0 mixture; this can be ascribed to the synergistic effects of nano-sil slag, resulting in the densification of the microstructure. On the other hand, accor the CHBDC [48], it is stipulated that the concrete base should have a minimum

Bond Strength
There has been an increasing demand to optimize the structural element, and this can be achieved by combining two different materials. Such composite structures are often named as a layered or hybrid structure, where the interaction and bond between the different materials are considered as a major challenge for design engineers, as bond failure is a critical cause of deterioration in layered structures. Therefore, the pull-off test was adopted to evaluate the monolithic behaviour between the FRCC layer with base the concrete and capture the risk results from the incompatibility between the two layers. It is worth mentioning that the specimens in the pull-off test are subjected to pure tensile stresses, which represents a severe scenario for the specimen.
The average bond strength values obtained from eight cores for each mixture at 28 days are shown in Figure 8. The results showed that the mixtures prepared without any fibers (N-X-0.0 and H-X-0.0) had a bond strength of 1.44 and 2.2 MPa, respectively. Both mixtures experienced an undesirable mode of failure, as the failure occurred mainly in the composite itself, as shown in Figure 9. This may be ascribed to the N and H composites, prepared without any fibers, which had tensile strength lower than that of the base concrete, the bond line between the two layers or the epoxy used to bond the steel disk. Compared to the control mixture N-X-0.0, there was a slight improvement in the bond strength of the H-X-0.0 mixture; this can be ascribed to the synergistic effects of nano-silica and slag, resulting in the densification of the microstructure. On the other hand, according to the CHBDC [48], it is stipulated that the concrete base should have a minimum bond strength of 1.5 MPa for bond-critical applications. The results herein indicated that the inclusion of fibers in the N and H composites, despite the type or the dosage, markedly improved the bond strength, which were in the range from 3.51-3.89 MPa. For example, adding BF pellets at dosages of 2.5, 4.5%, and 6.9% in the H composite enhanced the bond strength by 73, 70, and 68 %, respectively. This significant effect of incorporating discrete fibers was statistically supported by ANOVA for the bond strength, since adding BF pellets to the H composites at different dosages yielded an F value of 164.0, which was greater than the F cr of 4.2. At a fixed BF pellet dosage, changing the cementitious composite from N to H showed a negligible improvement in the bond strength, with statistical insignificance (Table 5). Consistently, increasing the BF dosage or using steel fibers instead did not contribute to enhancing the bond strength. Therefore, the bond strength for all fibrous composites were quite similar, and this may be attributed to the failure of all specimens containing BF pellets or SF shifting toward the base concrete (see Figure 9), suggesting that the assembly behaved as an integral system with a high degree of compatibility.

Penetrability
Penetrability is considered a major factor that affects the durability/longevity mentitious composites in their resistance to the ingress of moisture and aggressi stances and was assessed by the RCPT test at 28 days. The average penetration dep results of passing charges, and the corresponding penetrability class according to

Penetrability
Penetrability is considered a major factor that affects the durability/longevity of cementitious composites in their resistance to the ingress of moisture and aggressive substances and was assessed by the RCPT test at 28 days. The average penetration depth, the

Penetrability
Penetrability is considered a major factor that affects the durability/longevity of cementitious composites in their resistance to the ingress of moisture and aggressive substances and was assessed by the RCPT test at 28 days. The average penetration depth, the results of passing charges, and the corresponding penetrability class according to ASTM C1202 [33] are listed in Table 9. According to the qualitative indication of the chloride ion penetrability, the cement-based composites, irrespective to the type and dosage of the fibers included, had low penetrability since the passing charges fall in the range from 1000-2000 coulombs. On the other hand, the inclusion of SCMs such as slag and nanosilica, despite the type or the dosage of fibers, significantly reduced the passing charges to become lower than 1,000 coulombs, which can be classified as "very low" penetrability as per ASTM C1202 [33]. For example, the passing charges of H-X-0.0, H-B-2.5, H-B-4.5, H-B-6.9, and H-S-1.0 specimens were 64, 70, 69, 66, and 60% less than that of N-X-0.0, N-B-2.5, N-B-4.5, N-B-6.9, and N-S-1.0 specimens. This trend was substantiated by the physical penetration depth results, as these mixtures had markedly lower penetration depths (less than 8 mm) relative to that of the counterpart mixtures cast with cement only. Exemplar measurements for the penetration depth are shown in Figure 10. This was ascribed to the smaller particle size of nano-silica (approximately 35 nm), which provides a huge surface area (80,000 m 2 /kg), as it vigorously speeds up the rate of cement hydration. In addition, nano-silica can contribute physical filler and pozzolanic effects to the cementitious matrix, which led to densifying the cementitious matrix and increasing its chloride penetration resistance.  Although adding discrete fibers had several advantages, it was also reported that fibers introduce more transition zones in the matrix resulting in increased permeability [14,49]. Conforming to the strength results, the chloride penetration resistance decreased with the addition of BF pellets compared to the control mix, which contains zero fiber, despite the cementitious composite type. For example, the control mixtures N-X-0.0 and H-X-0.0 had passing charges and penetration depths of 1,103 and 398 coulombs, and 11.3 and 3.1 mm, respectively. These values were significantly increased to 1,798 and 617 coulombs, and 15.2 and 7.9 mm, respectively (Table 9) when BF Pellets were incorporated at a higher dosage of 6.9% in both mixtures (N-B-6.9 and H-B-6.9). In the same context, increasing the BF dosages led to the increased penetrability of the composites. Increasing the dosage of BF pellets from 2.5 to 4.5 and further to 6.9% in the N composites led to a 12 and 20% increase in the passing charges. Correspondingly, for the H composites, these values were 11 and 33% higher for the 4.5 and 6.9% BF pellet specimens than that of the 2.5% specimens. From Table 9, it can be noted that the specimens containing SF, irrespective of the cementitious composite type, had higher passing charges than those of corresponding 15.2 7.9 Although adding discrete fibers had several advantages, it was also reported that fibers introduce more transition zones in the matrix resulting in increased permeability [14,49]. Conforming to the strength results, the chloride penetration resistance decreased with the addition of BF pellets compared to the control mix, which contains zero fiber, despite the cementitious composite type. For example, the control mixtures N-X-0.0 and H-X-0.0 had passing charges and penetration depths of 1,103 and 398 coulombs, and 11.3 and 3.1 mm, respectively. These values were significantly increased to 1,798 and 617 coulombs, and 15.2 and 7.9 mm, respectively (Table 9) when BF Pellets were incorporated at a higher dosage of 6.9% in both mixtures (N-B-6.9 and H-B-6.9). In the same context, increasing the BF dosages led to the increased penetrability of the composites. Increasing the dosage of BF pellets from 2.5 to 4.5 and further to 6.9% in the N composites led to a 12 and 20% increase in the passing charges. Correspondingly, for the H composites, these values were 11 and 33% higher for the 4.5 and 6.9% BF pellet specimens than that of the 2.5% specimens.
From Table 9, it can be noted that the specimens containing SF, irrespective of the cementitious composite type, had higher passing charges than those of corresponding specimens comprising BF pellets. This was attributed to the RCPT test based on electrical conductivity as the presence of steel or metallic fibers enhanced the conductivity of the specimens, depending on their continuity in the matrix, and produced misleading results in terms of the charges migrating through the specimen. A similar observation was reported by Hossain et al. [50] and Ghazy et al. [49]. As such, this highlighted the role of using an alternative measurement (chloride penetration depth), which better correlates to the physical characteristics of the pore structure of the cementitious matrix to alleviate and capture biases induced by conductive material (e.g., steel fibers) that influence the resistivity of the cementitious matrix. For example, including SF in the N and H composites yielded the highest passing charges with 1,843 and 732 coulombs, respectively, which would give the impression that the specimens containing SF had a pore structure that would facilitate the ingress of fluids into the matrix. However, interestingly, the penetration depths for both mixtures, N-S-1.0 and H-S-1.0, were 11.9 and 4.2 mm, respectively, which were less than the penetration depths for all specimens containing BF pellets, despite the dosage included.

Conclusions
Based on the specific material types, mixture designs, and tests implemented in this study, the following conclusions can be drawn:

•
The inclusion of SF in the H composites reduced the flowability, whereas the replacement of SFs by BF pellets at different dosages had less effect on the flowability and flow loss, which makes the BFRCC suitable for field applications in terms of the placement and finishability process.

•
The results generally show that the early-age and later-age compressive strength of the H composites comprising different types and dosages of fibers markedly improved, as all values were above 55 MPa at seven days. Hence, the inherently slower rate of strength development of cementitious systems containing slag can be controlled by the addition of a small dosage (6%) of nano-silica.

•
Compared to the control mixtures without fibers, BFRCC mixtures with fibers yielded lower compressive strength, especially with higher dosages of BF pellets; however, the mode of failure considerably changed from brittle to ductile.

•
The layered prisms reinforced with high dosages of BF pellets (H-B-4.5 and H-B-6.9) exhibited a pseudo strain-hardening process (ranging between 47 and 45 J), while the prisms reinforced with SF (H-S-1.0) showed a strain-softening behavior.

•
Keeping the volume of BF pellets and SF constant (H-B-2.5 vs H-S-1.0) showed comparable post-cracking behavior. • At a fixed fiber dosage, the incorporation of FRCC, as a layer in the tension side only, yielded comparable toughness and maintained acceptable post-peak performance to counterpart specimens comprising FRCC over the full depth. This notion has proven to be technically more efficient and economic than the common practice of adding the fibers over the whole cross-section.

•
The superior bonding of BF pellets with the cementitious matrix was one of the main reasons for such an enhanced post-cracking behavior compared to SF, which is promising to produce high strength and high ductility cementitious composites using non-metallic fibers.

•
In comparison to N-X-0.0 and H-X-0.0, the pull-off test results showed that the bond strength of all fibrous composites, despite the type or dosage of the fibers included, increased. In addition, the bond strength for the later specimens were quite similar since the failure of the specimens occurred in the base concrete. • Compared to the control specimens without SCMs (N composites) and irrespective of the dosage of fibers, the passing charges of H composites were less than 1000 coulombs, which signified the synergistic effects of nano-silica and slag on densifying cementitious systems comprising different types of fibers and reducing their penetrability (as shown by the low penetration depth in the RCPT).

•
Overall, the results showed the efficacy of developing a corrosion-free composite for improving the post-cracking behavior of specimens, as they successfully controlled the progress of cracks and behaved similarly to the samples cast with SF, which can be proposed as a promising solution for infrastructure applications such as bridge girders or overlays. Data Availability Statement: All data, models, and code generated or used during the study appear in the submitted article.