Spin-Orbit Angular Momentum Conversion in Metamaterials and Metasurfaces

In the last decades unprecedented progress in the manipulation of spin angular momentum (SAM) and orbital angular momentum (OAM) of light has been achieved, enabling a number of applications ranging from classical and quantum communication, to optical microscopy and super-resolution imaging. Metasurfaces are artificially engineered 2D metamaterials with designed subwavelength-size building blocks, which allow precise control of optical fields with unparalleled flexibility and performance. The reduced dimensionality of optical metasurfaces enables new physics and leads to functionalities and applications that are remarkably different from those achievable with bulk materials. In this review, we present an overview of the progress in optical metasurfaces for manipultation of SAM and OAM of light, for applications in integrated spin-orbit conversion (SOC) devices.


Introduction
It is well known that besides linear momentum, electromagnetic (EM) waves possess angular momentum (AM), which can be decomposed into spin angular momentum (SAM) and orbital angular momentum (OAM). Circularly polarized waves carry SAM, quantized as ± per photon for left-hand circular (LHC) and right-hand circular (RHC) polarizations, respectively. On the other hand, OAM describes the azymuthal angular dependence of photons, and is quantized as l per photon with l any integer. Different l-values correspond to mutually orthogonal OAM modes and the total number OAM modes is unbounded. OAM modes have been used to encode information and thus to enhance the channel transmission capacity, via OAM multiplexing and multicasting techniques. Optical vortices characterizing OAM beams also find a number of applications in super resolution imaging, optical tweezers, and detection the rotation of particles [1,2,3,4,5].
2D metamaterials, also known as metasurfaces, is an emerging interdisciplinary field which promotes the of use alternative approaches for manipulation of light based on arXiv:1904.02647v1 [physics.optics] 4 Apr 2019 subwavelength-thick metasurfaces built upon metaatoms, with spatially varying compositions. They exhibit remarkable properties in manipulation of light at a 2D interphase. Metasurfaces can not only achieve the functionalities of the 3D counterparts, such as negative refractive index and invisibility cloaking, but they can also resolve some of the current limits present in 3D metamaterials, such as high resistive loss. In addition, metasurfaces can be easily fabricated via standard nanofabrication techniques, such as electron-beam lithography, techniques readily available in the semiconductor industry.
In this review, we present some of the recent advances in 2D metamaterials and metasurfaces, and their major applications in generation and manipulation of spin angular momentum (SAM) and orbital angular momentum (OAM) of light via spinorbit-conversion (SOC) [1,2,3,4,5]. In Section 2 we describe the basic building blocks of metasurfaces. In section 3 we present a theoretical introduction to the concepts of spin angular momentum (SAM) and of orbital angular momentum (OAM) of light. In Section 4 we present the use of metasurfaces in the control of polarization or spin angular momentum (SAM) of light, of orbital angular momentum (OAM), and of total angular momentum (TAM) via q-plates and J-plates. In Section 5 we review current applications of metasurfaces as OAM multiplexing and multicasting techniques for high speed optical communication. Finally, in Section 6 we outline the conclusions.

Metasurface building blocks
Metasurfaces are 2D artificially engineered materials made of subwavelength metaatoms which enable exotic optical and electromagnetic properties unavailable in natural compounds. Due to the unique wave behaviors that result from stongly localized lightmatter interaction, metasurfaces have the ability to overcome many tough problems faced by traditional materials, such as breaking of the diffraction limit, the generalized laws of refraction and reflection, as well as the localized enhancement of light absorption. 2D metamaterials exhibit enhanced light-interaction via plasmonic resonances [1][2][3][4][5]. When a resonant external electric field is applied, electrons inside plasmonic materials are shifted from their steady-state positions resulting in a macroscopic polarization, which in turn generates an internal electric field to restore the electrons to their steadystates. Under harmonic excitation, collective oscillations can be generated. Depending on the size of plasmonic particles, they can be polarized either completely (small particles compared to wavelength) or only at the surface (larger particles compared to wavelength), resulting in simple dipolar resonances or multipole resonances, respectively. The resonant frequency depends on size, shape, refractive index, and surrounding media. On a metasurface, secondary waves reflected or transmitted through the nanoparticles acting as nanoantennas will gain different phase shifts, and thus they can interfere and generate arbitrary wave fronts. In order to increase the phase shift, the shape of the nanoantenna can be artificially engineered. V-shaped nanoantennas (14,15) can support two resonant modes: a symmetric mode and an antisymmetric one. In coherent superposition of such resonance modes, a phase shift of 2π can be successfully generated for light whose polarization is perpendicular to that of the incidence. In order to mitigate the low efficiency associated with polarization conversion, an alternative design can be employed incorporating a metallic ground plane separated from the top nanoantenna array by a thin dielectric layer (12,15). Light incident will induce antiparallel electric currents on the nanoantennas and ground plane, creating a gap resonance and extending the phase shift, ideally to 2π. Because plasmonic materials can provide strong optical resonances, they were initally chosen as the building blocks of metasurfaces (14,15). However, a significant limitations of plasmonic metasurfaces is energy dissipation into heat (7), or resistive loss. Such resistive loss reduces the overall efficiency of plasmonic devices, thus precluding them from important applications. Additionally, due to the great capacity of plasmonic structures in light confinement at the nanoscale, incident light fields can significantly increase the local temperature, for this reason such plasmonic structures usually present a low power threshold of deformation. Noble metals, such as gold and silver, are widely used as the building components for plasmonic nanostructures, which can increases the fabrication cost and can be incompatible with current semiconductor fabrication processes.
To overcome some of these limitations, alternative metasurface designs using only dielectric components have been proposed (12). Nanostructures composed of dielectrics with high refractive indices, such as silicon, germanium, and tellurium, can manipulate light through Mie resonances (12)(13)(14)(15) and can achieve both electric and magnetic fields enhancement. A significant advantage of dielectric materials is that they are associated with low resistive loss, due to small imaginary part of permittivity, and can in principle enable highly efficiencient devices. Moreover, fabrication of dielectric metasurfaces is compatible with state of the art semiconductor processes. As a simple example to illustrate the resonance of dielectric nanoantennas, for sphere-shaped resonators the two lowest resonant modes excited are the electric and magnetic dipolar resonances (13). By overlapping such lower order resonances, it is possible to achieve a phase difference over the entire 2π-range. In addition, when electrical and magnetic dipole moments have perpendicular orientations, scattered light is unidirectional, which can be exploited to make reflection-free metasurfaces (14,15). Aside from dielectric metasurfaces based on plasmonic antennas, there is growing interest in nanoresonators exhibiting Fano resonances, arising from interference between broad spectral lines with narrow resonances (16)(17)(18). By designing antennas with broken symmetry, weak coupling of plasmonic modes to free-space radiation modes can enable Fano resonances with narrow linewidths and high Q-factor. Fano resonances are also observed in pure dielectric systems through coupling of magnetic and electric dipolar modes. The Fano resonance is directional due to constructive interference. Moreover, the scattering direction is sensitive to frequency shift, which can be exploited in sensing and switching applications.
Finally, there is an alternative approach for phase modulation in metasurfaces based on the geometric-phase (or Berry phase) elements to achieve tunable phase shifts in metasurfaces, it should be noted that typically this approach works only for circularly polarized light (19)(20)(21)(22)(23)(24)(25). The building blocks of geometric phase metasurfaces can be described as polarization wave-plates with spatially varying orientations of fast axes (see Figure 1 A-C). This space-variant polarization convertion can be easily described using Jones formalism for polarized light, obtaining an expression for the trasformation matrix T (x, y): where J(φ) represents the Jones matrix of a retarder plate with retardation φ, R is a rotation matrix and θ is the orientation of the fast axis of the rotation plate. As will be described in the following Sections, it is apparent that by transmission on a geometricphase variant metasurface RHC or LHC light will be converted into the opposite circular polarization, and will aquire an additional spatially dependent geometric phase of the form 2θ(x, y). By rotating the spatially varying waveplate from 0 to 180 degrees, the induced phase shift can be continuously tuned from 0 to 2 π. This phase shift is purely geometric, therefore it has a broad bandwidth. Its performance is limited only by the scattering efficiency of the nanoantennas. Moreover, geometric-phase elements can be resonantly excited to increase the scattering efficiency. The spatially varying phase shift θ(x, y) can be taylored in order to produce controlled orbital angular momentum (OAM) vortex states. This transformation is the called Spin to Orbital Angular Momentum conversion (SOC), as described in detail in the Section 2. Figure 1 depicts different approaches to OAM generation in 2D Metamaterials and Metasurfaces.

Spin Angular Momentum (SAM) of Light
The spin angular momentum (SAM) and orbital angular momentum (OAM) of light are separately observable properties in optics. For paraxial monochromatic beams, a spin-orbital angular momentum decomposition is straightforward. This unique feature explains in part the recent unprivalled progress in photonic SAM-OAM conversion in metasurfaces and 2D metametrias, which motivates this review.
In brief, the spin angular momentul (SAM) is associated with the polarization of light, so that right-hand circular (RHC) and left-hand circular (LHC) polarizations of a paraxial beam correspond to positive and negative helicities σ = ±1 of a photon. If the mean momentum of the beam (in units of per photon) can be associated with its mean wave vector k , then such beam carries the corresponding SAM S = σ k /|k|, where the helicity parameter σ is equivalent to the degree of circular polarization in the Jones formalism.
More specific, a plane wave is an idealized entity which extends to infinity. Such plane wave cannot carry extrinsic orbital angular momentum (analogue to the mechanical counter part L = r × p), because its position r is undefined. On the other hand, a circularly-polarized electromagnetic plane wave can carry SAM. A circularly polarized plane-wave propagating along the z-direction can be written as: wherex,ŷ,ẑ are unit vectors, and the helicity parameter σ = ±1 corresponds to the LHC and RHC polarizations, respectively. The wave number |k|, results from the dispersion relation for a plane wave is |k| = ω/c. The electric E field represents the eigenvector of the z-component of the spin-1 matrix operator S (generators of the SO(3) vector rotations), with eigenvalue σ of the form S z E = σE. Therefore, the plane wave carries SAM density S = σ k |k| defined as the local expectation value of the spin operator with the electric field (Eq. 2).

Orbital Angular Momentum (OAM) of Light
The first demonstration of the mechanical torque created by the transfer of angular momentum of a circularly polarized light beam to a birrefringent plate was performed by Beth in 1936 [22]. In this experiment a half wave-plate was suspended by a fine quartz fiber (Figure 2 a). A beam of light circularly polarized by a fixed quarter-wave plate passed through the plate which tansformed RHC polarization, with spin component − , into LHC polarization, with spin component + , with a net spin angular momentum transfer of 2 per photon to the birrefringent plate. Beth meaured torque agreed in sign and modulus with the quantum and classical predictions, his experiment is usually referred to as the measurement of spin angular momentum of the photon.
In Ref. [23], it was demonstrated that Laguerre-Gaussian modes, with azimuthal angular dependence exp [−ilφ], are eighen-modes of the momentum operator L z and carry an orbital angular momentul l per photon. A convenient representation of a linearly polarized TEM plq laser mode can be obtained, in the Lorentz gauge, using the vector potential [23]: wherex is the unit vector in x-dir and u(r, φ, z) is the complex scarlar field amplitude satisfying the paraxial wave equation. In the paraxial approximation, second derivatives and the products of first derivatives of the electro-magnetic field are ignored, and du/dz is taken to be small compared to ku. The solutions for the cylindrically symmetric case u r,φ,z , describing the Laguerre-Gauss beam, are of the form [23]: where z R is the Rayleigh range, w(z) is the radius of the beam, L l p is the associated Laguerre polynomial, C is a constant and the beam waist is taken at z = 0. Within this description, the time avarage of the real part of the Poyting vector 0 E × B, which is the linear momentum density, results in: where z is the unit vector in z-dir. When applying to a Laguerre-Gaussian distribution given in Eq. 4, the linear momentum density takes the form: wherer,φ are unit vectors. It may be seen that the Poynting vector (c 2 P ) spirals along the direction of propagation along the beam (Figure 2 b). The r component relates to the spatial spread of the beam, the z component relates to the linear momentum, and the φ component gives rise to the orbital angular momentum.

OAM modes and topological charge
Optical vortices characterizing beams of photons propagating with a phase singularity of the form exp[ilφ], with l is an integer number, have a topological structure on its wavefront characterized by a topological charge l, arising from its helical spatial wavefront which spirals around the phase singularity, as depicted in Figure 2 b. The topological structure in the wavefront is not only limited to EM waves, but can also be found in acoustic waves, electrons and neutrons [3]. At the singularity, the phase is not defined and the polarization and amplitude vanish altogether, resulting in a dark centre within the wavepacket, as depicted in Figure 2 c. Such singularity can be considered a screw dislocation. It is remarkable that optical dislocations have not only been observed in spacial Laguerre-Gauss laser modes but they were also predicted and observed in laser scattering speckle fields, resulting from the interfering of multiple plane waves. Therefore, optical dislocations are currently considered a universal phenomenon. A high degree of control over the different approaches for generation and manipulation of vortex beams carrying OAM has been achieved in the last couple of decades, at an unparalleled rate. Similarly impressive are the potential avenues of applications ranging from optical microscopy, micromanipulation, to classical and quantum communications, among other exciting research directions [1,2,3,4,5]. Geometric phase elements and metasurfaces [59], also known as q-plates can couple SAM and OAM, by converting a given state of circular polarization into its opposite, while imprinting an azimuthal phase profile with a fiwed topological charge. On the other hand, generalized metasurfaces [58] can transform arbitrary input SAM states (i.e., elliptical polarization) into arbitrary output states of opposite TAM. Such devices are also known as J-plates. In the next sections we provide an overview of the transformations that can be achieved with q-plates and J-plates respectively, using tailored metasurfaces.

SAM control in metasurfaces
In the same manner as conventional wave plates, metasurfaces enable polarization conversion through manipulation of two eigenmodes of light corresponding to orthogonal polarizations. To design a metasurface for polarization conversion, one should know the Jones vector of the incident field and the Jones vector of the desired output fields. With such knowledge, a Jones matrix J(x, y) for each spatial point (x, y) on the metasurface plane linking the incident and output waves can be determined. The calculated Jones matrix can be achieved by engineering proper nanoantenna patterns. Up to now, conversion between a linear polarization and a circular polarization, between different linear polarization states, or between opposite circular polarization states has been reported using metasurfaces. Geometrical phases can be generated by engineering the metasurface with identical nanoantennas of spatially varying orientations, as described in Section 1. One major limitation of geometric-phase metasurfaces is that they work only for circularly polarized input light, therefore the geometric phase must be carefully matched to the propagation phase to achieve arbitrary control of polarization states. This is typically achieved via hybrid patterns of nanoantennas.

OAM control in metasurfaces
Polarization-control in metasurfaces which enable manipulation of the propagation phase and the geometrical phase can also be utilized in the generation of optical vortex beams carrying net topological charge (l) or orbital angular momentum (OAM) of light (20)(21)(22)(23)(24)(25)(26)(27)(28)(29)(30)(31)(32)(33)(34)(35)(36). One of the most distinct feature of such OAM beams is their helixed wave front, a direct consequence of the dependence of phase on the azimuthal angle. The order of OAM is labeled by an integer l, given by the number of the twists a wave-front contains (per unit wavelength). OAM has been widely recognized as an unbounded degree of freedom of light, which can be utilized in high-speed free-space optical communication systems (27)(28)(29)(30)(31)(32)(33)(34)(35)(36)(37) since beams with different orders of OAM are orthogonal they do not interfere with each other. Traditional methods for generation of OAM beam include spatial light modulators (SLM), holograms, laser-mode conversion, and spiral phase plates (SPP) (Figure 1). On the other hand, metasurfaces can create helical wave fronts by arranging nanoantennas with linearly increasing (or decreasing) phase shifts along the azimuthal direction (38)(39)(40)(41)(42)(43)(44)(45). As a result, a metasurface can add an optical vortex to the incident light wave front, thus converting SAM into OAM, this transformation is also termed spin-to-orbit conversion (SOC) (46,47). Normally the SOC permits only the conversion of LHC and RHC polarizations into states with opposite OAM, due to conservation of total angular momentum (TAM). By providing an additional phase shift in the azimuthal direction, a metasurface can convert circular polarizations into states with independent values of OAM. In recent years, conversion of light with arbitray elliptical polarization states into orthogonal OAM vortex states was demonstrated (47,48).

TAM control in metasurfaces
Phase elements with spatially varying orientations can introduce a controlled geometric phase, and provide for a connection between polarization (SAM) and phase (OAM). These devices are typically made of periodic elements referred to as q-plates [22]. The exact transformation performed by q-plates can be expressed as: where LHC and RHC polarizations are converted to its opposite spin state, with an OAM charge of ±2q per photon (Figure 3a). This transformation is usually referred to as spin-orbit-conversion (SOC). As described in the previous section, typically the only elements that vary the angle spatially are those which perform the rotation (i.e., θ(x, y)). For this reason the OAM output states are constrained to conjugate values (±2q ). Moreover, due to the symmetry of the device, the SOC operation performed by q-plates is limited to SAM states of circular polarization (Figure 3a). In order to perferm SOC operations in arbitrary SAM states, such as elliptic polarizations, a more general device is required. This arbitrary mapping can be performed by J-plates, as described below.
A J-plate has the hability to map arbitrary input SAM states, i.e., not limited to RHC or LHC, into two arbitrary TAM states (represented by the variable J). A J-plate can be realized employing any medium that enables birrefringence, absolute phase shift, and retarder orientation angles to vary spatially. In other words, in addition to the spatial orientation of the fast axes of rotation plates, the relative phase shift between orthogonal spins should also vary spatially (φ = φ(x, y)). In Ref. [58], a J-plate was where the parameters (χ, δ) determine the polarizations state. Implementing the SOC operation reduces to determining the actual Jones matrix J(φ) that transforms J(φ)|λ+ = e imφ |(λ+) * and J(φ)|λ− = e inφ |(λ−) * . It can be demonstrated that the required spatially varying Jones matrix has the form: We stress that no traditional phase plate can provide for the required control and sub-wavelength spatial variations in phase shift, birrefringence and orientation. Subwavelength space metasurfaces on the other hand, can enable such control.

Alternative approaches for spin-orbit conversion (SOC)
Controllable geometric-phases can also be introduced via space-variant polarizationstate manipulation using subwavelength metal stripe space-variant gratings, as proposed by Bomzon et al, in 2001 [64]. This realization is based on a subwavelength metal stripe space-variant grating (SVG) designed for converting circularly polarized light into an azimuthally polarized beam. SVGs are described by a vector: where Λ is the period of the grating, and β(x, y) is a spatially varying vector perpendicular to the metal stripes. The polarization of the transmitted beam through the grating can be expressed as: where J(Λ) is the Jones matrix representing the SVG of period Λ for β = 0, and R(β(x, y)) is a 2x2 spatially varying rotation matrix (Figure 4 a). J(Λ), typically a diagonal matrix because the eigenpolarizations of the grating are oriented parallel and perpendicular the grating vector. Similarity between Eq. 1 and Eq. 12 reveal that both the metasurface and the SVG approach produce a transformation described by the same Jones matrix.
In addition, successful alternative approaches for SOC using metasurfaces based on high-contrast dielectric elliptical nanoposts have been recently implemented [63]. The metasurface is composed of a single-layer array of amorphous silicon elliptical posts with different sizes and orientations, resting on a fused-silica substrate. The elliptical posts are placed at the centres of hexagonal unit cells or pixels (Figure 4 b). In brief, each post can be considered as a waveguide that is truncated on both sides and operates as a low-quality-factor FabryPerot resonator. The elliptical cross-section of the waveguide leads to different effective refractive indices of the waveguide modes polarized along the two ellipse diameters. As a result, each of the posts imposes a polarization-dependent phase shift on the transmitted light field E out (x, y) and modifies both its polarization and phase. This implementation provides complete control of polarization and phase with subwavelength spatial resolution and an experimentally measured efficiency ranging 72% to 97% from thus significantly improving transmission efficiency upon previous realizations [59]. Such complete control enables the realization of most free-space transmissive optical elements such as lenses, phase plates, wave plates, polarizers, beamsplitters, as well as polarization-switchable phase holograms or arbitrary vector beam generators using the same metamaterial platform.

Applications in OAM multiplexing and multicasting techniques
Metasurfaces can contribute to a new class of chip-scale devices, which are expected to revolutionize nanophotonic and optoelectronic circuitry through smart integration of multiple functions in metallic, dielectric, or semiconductor building blocks. Their 2D nature is a signifcant advantage for wafer-scale processing and integration, therefore among artificially engineered materials, metasurfaces hold great promise to excell in technologically relevant applications. Here we will focus on applications of metasurfaces in integrated OAM multiplexing and multicasting devices, for high-speed data transmission [1] [55], [54], [56], [57].
Orbital Angular Momentum (OAM) division multiplexing is an experimental technique for increasing the transmission capacity of electromagnetic signals using the OAM of the electromagnetic waves to distinguish between the different orthogonal channels. It is the analogue of wavelength division multiplexing (WDM), time division multiplexing (TDM), or polarization division multiplexing (PDM) (49), in the subspace spanned by OAM of light. While spin angular momentum (SAM) or polarization multiplexing offers only two orthogonal states corresponding to the two states of circular polarization, OAM multiplexing can access a potentially unbounded set of states, and as such can offer an infinite number of channels for multiplexage. Although OAM multiplexing promises very significant improvements in bandwidth (2.5 Tbit/s transmission rates in MIMO systems have been reported), it is still an experimental technique, and has so far only been demonstrated in the laboratory, over relatively small distances of a few Kms over OAM maintaining fibers. In addition to the reduced transmission distances, one of the main limitations for scalable OAM multiplexage is the extreme bulkiness of the optical components required both for OAM generation and for OAM detection. Recently (50,51), an OAM multiplexing scheme in the Terahertz (THz) band based on use of a single-layer metasurfaces was demonstrated experimentally for the first time. The designed structure generates four focused phase vortex beams that have different topological charges (or OAM number l) under illumination by a Gaussian beam, which means that OAM multiplexing with four channels is realized (see Figure  4). When an individual vortex beam is used as the incident light, only one channel is identified and extracted as a focal spot; that is, demultiplexing of the OAM signal is achieved. The metasurface structure has subwavelength-level thickness, which enriches the number of potential approaches available for the miniaturization and integration of THz communication systems. The performance of the designed OAM multiplexing and demultiplexing device shows excellent agreement between the theoretical predictions and experimental results, indicating that this device is suitable for scalable ultra high-speed THz communications.

Orbital Angular Momentum Multicasting
OAM multicasting consists of generating multiple coaxial OAMs from a single input, a promissing feature for efficient optical processing in one-to-many communications. This approach speeds up the end users to acquire the duplicate data, by replicating data into orthogonal multiple channels in the optical domain. Optical multicasting is used in many optical communication applications, such as interactive distance learning, video distribution, teleconferencing, and distributed computing. To this end, Spatial Light Modulators (SLM) can be loaded with suitably designed phase patterns. A pattern search assisted iterative (PSI) algorithm was proposed to enable simultaneous generation of multiple OAM modes using a single phase-only SLM elements [1]. In addition, metasurface structures with a V-shaped antenna array can also be used to realize on-chip multicasting, from single Gaussian beams to multiple OAM beams [1]. Additionally, adaptive multicasting assisted by feedback, from a single Gaussian mode to multiple OAM modes was demonstrated using a complex phase pattern. Finally, OAM multicasting by manipulation of amplitude and phase, turbulence compensation of distorted OAM multicasting by adaptive optics, and data carrying OAM-based underwater wireless optical multicasting link were also demonstrated, revealing the exceptional performance of OAM multicasting and its broad applications [1].

Discussion
The realization of spin-orbit-convertion (SOC) in metasurfaces and metamaterials may have signifcant impact in diverse scientific and technological areas and can open a number of exciting research directions. The 2D nature of q-plates and generalized J-plates enables easy integration and holds the promise of solving scalability issues. Such 2D metasurfaces could be easily integrated into laser cavities producing arbitrary Laguerre-Modes OAM states as well as tunable TAM states [58]. On the other hand, we have described multiplexing and multicasting applications for encoding information in contrallable optical states using both polarization (SAM) and azymuthal phase (OAM) which could potentially increase the bandwidth of optical communication beyond stateof-the-art. In addtion, controllable structured light produced by J-plates can be used for fabrication of new materials via laser imprinting, optical micromanipulation, and stimulated-emission-depletion imaging. Although classical fields are mainly considered here, the physics of SOC also holds at the single-photon level given the one-to-one mapping between Jones formalism and single-photon polarization description. The transition to the quantum regime is particularly promissing in metasurfaces realization with demonstrated high transmission efficiency [63]. For all these reasons, SOC in metamaterials and metasurfaces can furnish a new tool for both classical and quantum communication, especially in schemes that rely on polarization to OAM conversion.

Conclusion
2D Metamaterials and metasurfaces is a fast growing interdisciplinary field, with significant applications in nanophotonics, biophysics, plasmonics, quantum optics, or telecommunication. They enable precise control of optical fields with unprecedented flexibility and performance. The reduced dimensionality of optical metasurfaces enables applications that are distinctly different from those achievable with bulk metamaterials. Metasurfaces can provide for a novel tool for generation and conversion of Orbital Angular Momentum (OAM), a feature which can promote many applications in integrated on-chip OAM multiplexing techniques, which hold the promisse of increasing transmission capacity and overcome scalabily issues beyond state-of-the-art.