Mathematical Modeling, Moisture Di ﬀ usion and Color Quality in Intermittent Microwave Drying of Organic and Conventional Sweet Red Peppers

: The aims of this research were to evaluate the inﬂuence of intermittent microwave drying on the moisture di ﬀ usion and color qualities of organically and conventionally grown sweet red peppers and mathematically express drying kinetic data. Pepper samples of 150 g were dried at 150, 300 and 450 W using a microwave oven. Results showed that intermittent microwave drying at 450 W occurred mainly in the falling rate period, whereas drying at lower powers resulted in relatively longer constant rate periods for both peppers types. The Midilli model provided the best ﬁt for all data. The moisture di ﬀ usivity (D e ﬀ ) values of organic and conventional samples ranged from 59.69 × 10 − 10 to 182.01 × 10 − 10 m 2 s − 1 and from 59.11 × 10 − 10 to 181.01 × 10 − 10 m 2 s − 1 , respectively, and the di ﬀ erence was insigniﬁcant. The pre-exponential factor for the Arrhenius equation (D 0 ) and activation energy (E a ) values were almost identical for both product types. Overall, organic or conventional growing did not alter the structural features related to the heat transfer properties. 300 W for organic peppers and 150 W for conventional peppers gave the highest ∆ L*, ∆ a* and a* / b* values, producing the most bright and red pepper powders. Thus, these treatments can be used to produce higher color quality powders.


Introduction
Organic farming has been gaining importance both in the world (31.5 million to 69.8 million ha increase in 2007-2017) and in Turkey (0.17 million to 0.54 million ha increase in 2007-2017), which ranked 17th in the world in terms of the amount of organic farmland [1,2]. Organic farming offers pesticide residue-free, healthy, and tasty products [3]. Since organic fruits and vegetables are not subjected to synthetic chemical pesticides and fertilizers, they use higher amounts of metabolic energy to produce secondary plant metabolites such as antioxidants and phenolic compounds [4]. It was reported that the secondary metabolites in organic fruits and vegetables were 12% higher than in conventional samples [5]. Hence, growing conditions of the product could affect the phytochemical content, structure, taste and aroma. It was mentioned that organic products have higher antioxidant activity, higher levels (18-69%) of antioxidants, phenolic compounds and other plant secondary metabolites and also, lower amounts of agrochemical residues (75%) and cadmium (48%), which all related to chronic and neurodegenerative diseases and certain cancers [6].
Pepper (Capsicum annuum L.) is a very important source of food, medicinal and industrial products as a cheap source of vitamins, fibers and minerals [7]. It is consumed as fresh or dried and is also used for the production of spices, pastes, natural colorants, soups, sauces and oleoresin [8]. The total pepper production was about 36.1 million tonnes in the world and 2.6 million tonnes in Turkey [9]. Organic pepper production is important, with about 5558 tonnes (in 2018) in Turkey [10].
Nowadays, the demand for dried organic products has increased remarkably with the spectacular trends in the healthier food market. Pepper fruits can quickly rot after harvest due to the high initial moisture content being up to 90% wet-based [8]. Hence, fresh fruits, like peppers, are highly perishable products and are generally dried to increase their shelf life and make them accessible to consumers during the whole year. Various drying practices such as sun, hot-air, infrared and microwave drying are applied to preserve this perishable product without impairing its quality such as color, valuable vitamins, minerals and nutrients. Though sun and hot air drying are still the most common methods to produce red pepper flakes and powdered spices, the drying process in both methods takes quite a long time and associated quality losses occur [11][12][13]. Use of microwaves to shorten the drying time and protect the quality of the final dried products is a promising alternative in drying of perishable agricultural products like pepper. Since microwaves affect the product as a whole, heating up the product volumetrically and pumping up the moisture from inside to outside, it eliminates case hardening and yields increased diffusion rates [14][15][16]. Nevertheless, it is well known that the continuous application of microwaves during the drying process could lead to overheating and uneven heating problems. Intermittent application of microwave energy can eliminate these drawbacks [17,18]. As intermittent application of microwave energy provides the rest time to allow moisture redistribution by limiting temperature increase, it results in higher energy efficiency and product quality [19][20][21][22]. Various studies signified the superiority of intermittent application of microwaves for various vegetables and fruits such as strawberry [23], banana [24], red pepper [8,25], carrot [26], oregano [27], fig [28], pumpkin [29] and apple [30].
Only very few studies have been reported comparing the effects of drying on organically or conventionally produced crops [31,32]. The first study [31] concentrated on the effects of freeze drying, air-drying and flash freezing on the total amount of ascorbic acid and phenolics of strawberry, marionberry and corn produced using conventional, organic and sustainable production practices, but it contained no information on the drying characteristics of the products. The second study [32] was related to the influence of air and freeze drying on the phytochemical content and moisture diffusivity of conventional and organic berries. No significant differences between the phytochemical contents in fresh conventional and organic berries were found. They stated that the air drying resulted in considerable changes in phytochemical compounds in both conventionally and organically grown berries, whereas freeze drying increased the phytochemicals and in some cases, it increased the phytochemicals contents as compared to air drying.
Even if there is an increasing demand for organic products due to the consumer preference for healthier and tastier foods, studies on the comparison of drying kinetics and color parameters of organic and conventional products have been very limited. Mathematical models could be useful to estimate the moisture and temperature of the product during the drying process and the drying capacity of the system. Therefore, the aim of this work was to compare the drying kinetics, mathematical models, moisture diffusion characteristics and color qualities of the organically and conventionally grown sweet red peppers dried by intermittent microwave drying.

Pepper Samples
Sweet red peppers (Capia pepper, Diyar F1 cultivar) produced in organic and conventional farming methods under greenhouse conditions were obtained directly from farmers located near Erdemli, Mersin, Turkey (36.6115 N, 34.2624 E). This type of pepper is intensively cultivated and consumed in Turkey. The peppers were hand harvested in the red stage and stored at +4 • C for one day, and then, the drying experiments were started and completed in ten days. The moisture contents of the pepper slices were determined by using a standard oven method (103 • C for 24 h). Before each drying experiment, three samples were utilized for moisture content determination. The average initial moisture contents of the organic and conventional pepper samples were 91.65 ± 0.20% (wet basis) and 92.06 ± 0.27% (wet basis), respectively.

Intermittent Microwave Drying (IMD)
A lab-scale microwave oven (MD 1605, Beko, Istanbul, Turkey) with a maximum rated power of 900 W at 2.45 GHz was utilized in the drying experiments. The size of the microwave oven cavity was about 22 × 35 × 33 cm. The microwave oven's actual power was calculated as 736 W by using the IMPI-2L test [33]. The experiments were carried out at three power levels (150, 300 and 450 W) by changing the microwave on and off times (T on and T off ) as controlled by a programmable logic controller (PLC) ( Table 1). The mass of the microwave turntable with the shredded pepper sample and air temperature inside the microwave cavity were recorded at every minute during the drying process. An axial fan was used to aspirate moist air from the drying chamber at about 1.5 ms −1 airflow speed. The peppers were washed with tap water, rinsed with distilled water, and then, they were dripped and shredded at a thickness of about 1.43 ± 0.09 mm. In each drying process, about 150 g of shredded pepper sample was distributed evenly and homogeneously in a layer with a thickness of 7.6 ± 0.07 mm on a glass tray with a 30 cm diameter ( Figure 1). All drying experiments were conducted in an acclimatized laboratory at room temperature. Moisture loss from the material was recorded at one minute intervals, with an accuracy of 0.01 g. All experiments were ended when the pepper samples reached a moisture level of about 0.10 kg [H 2 O] kg −1 [DM]. The drying procedure was repeated seven times at each of the three microwave power levels for both product types (organic and conventional) giving a total 42 drying experiments (3 × 7 × 2 = 42). AIMP-Applied intermittent microwave power; IM-Initial mean mass; SIMP-Specific intermittent microwave power; PP*-Power proportion; T on -On time; T off -Off time; PR-Pulse ratio; MCT-Mean cavity temperature; * PP was computed by dividing the AIMP by microwave oven's actual power (736 W); ** PR = (T on + T off )/T on [26].

Intermittent Microwave Drying (IMD)
A lab-scale microwave oven (MD 1605, Beko, Istanbul, Turkey) with a maximum rated power of 900 W at 2.45 GHz was utilized in the drying experiments. The size of the microwave oven cavity was about 22 × 35 × 33 cm. The microwave oven's actual power was calculated as 736 W by using the IMPI-2L test [33]. The experiments were carried out at three power levels (150, 300 and 450 W) by changing the microwave on and off times (Ton and Toff) as controlled by a programmable logic controller (PLC) ( Table 1). The mass of the microwave turntable with the shredded pepper sample and air temperature inside the microwave cavity were recorded at every minute during the drying process. An axial fan was used to aspirate moist air from the drying chamber at about 1.5 ms −1 airflow speed. The peppers were washed with tap water, rinsed with distilled water, and then, they were dripped and shredded at a thickness of about 1.43 ± 0.09 mm. In each drying process, about 150 g of shredded pepper sample was distributed evenly and homogeneously in a layer with a thickness of 7.6 ± 0.07 mm on a glass tray with a 30 cm diameter ( Figure 1). All drying experiments were conducted in an acclimatized laboratory at room temperature. Moisture loss from the material was recorded at one minute intervals, with an accuracy of 0.01 g. All experiments were ended when the pepper samples reached a moisture level of about 0.10 kg [H2O] kg −1 [DM]. The drying procedure was repeated seven times at each of the three microwave power levels for both product types (organic and conventional) giving a total 42 drying experiments (3 × 7 × 2 = 42).

Mathematical Modeling of Drying Curves
The data were fitted to various drying models to determine the best fitting drying equation. A total of eleven drying models were appraised in the study ( Table 2). The equilibrium moisture content (M e ) was assumed to be zero and therefore, the moisture ratio ( * MR-moisture ratio; k and k 1 -drying coefficients; n-exponent; t-time in minutes; a and b-model coefficients. Nonlinear regression analyses for these models were carried out in the SigmaPlot program (Version 12; Systat Software, San Jose, CA, USA). The coefficient of determination (R 2 ), standard error of estimate (SEE) and residual sum of squares (RSS) were utilized to select the best equation. These parameters were computed as follows: where MR exp,i is the ith experimental moisture ratio, MR pre,i is the ith estimated moisture ratio and N is the number of data.

Calculation of the Effective Moisture Diffusivity (D eff ) and Activation Energy (E a )
The effective moisture diffusivity (D eff ) values were interpreted by using Fick's second diffusion equation. The general solution of Equation (3) for slab geometry with the assumptions of diffused moisture migration, insignificant shrinkage, constant diffusion coefficients and temperature is given below [42]: ), D eff is the effective moisture diffusivity (m 2 s −1 ), L is the half thickness of the samples (m), i is a positive integer and t is time (s). For the long drying process, Equation (3) can be further simplified as follows [43]: The D eff values were calculated by plotting experimental ln(MR) data against drying time, so the plot provides a straight line with a slope as K = π 2 D eff /4L 2 .
In this study, the dependency of the effective moisture diffusivity (D eff ) on the ratio of applied microwave power to fresh sample mass were characterized with an Arrhenius-type exponential model Equation (5) derived by [44]: where D eff is the effective moisture diffusivity (m 2 s −1 ), D 0 (m 2 s −1 ) is a pre-exponential factor, E a is the activation energy (Wg −1 ), P a is the applied microwave power (W) and m is the fresh sample mass (g). Then, the E a was computed from the slope of the Equation (5) by plotting ln(D eff ) versus m/P a .

Color Analysis
The color of the fresh and dried-powdered red peppers was measured with a hand-held chromameter (Minolta CR-400, Osaka, Japan). The CIE L*a*b* color model was used. The chromameter was utilized with illuminant C standard and calibrated using its white reflector plate. The color in the L*a*b* model is expressed in three dimensions and the meaning of each parameter is as follow: L*-Brightness of the color (0-black; 100-white), a*-Redness-greenness (-60-green; +60-red), b*-Yellowness-blueness (-60-blue; +60-yellow). In measuring the color of the samples, ground material measurement apparatus was used. Color change of the material was evaluated by using the redness to yellowness ratio (a*/b*), total color difference (∆E*) and color difference values for all three parameters (∆L*, ∆a*, and ∆b*): where d and f refer to the dried and fresh products, respectively.

Statistical Analysis
Seven fresh samples and 42 dried-powdered samples (three power levels of 150, 300 and 450 W multiplied by seven drying experiments and two production methods) for both organic and conventional red sweet peppers were included in the data analysis. The effect of the drying temperatures on the color of the dried organic and conventional red pepper powder samples was statistically evaluated with a statistic software (SPPS, v.17, IBM, NY, USA) using one-way analysis of variance (ANOVA) and the means were compared with Duncan's test (p < 0.05).

Drying Kinetics
Change of moisture ratio (MR) in intermittent microwave drying of organic and conventional sweet red pepper shreds is presented in Figure 2 Table 3).
It was found that increasing the applied microwave power diminished the drying time significantly (p < 0.05). Compared to organic peppers, drying time of the conventional pepper shreds lasted 1 to 8 min longer. Except 150 W, no substantial difference was found between the drying times of organic and conventional pepper samples dried at 300 and 450 W power levels. Mean cavity temperature was found to be higher in conventional red pepper, probably due to the longer drying time (Table 1).

Drying Kinetics
Change of moisture ratio (MR) in intermittent microwave drying of organic and conventional sweet red pepper shreds is presented in Figure 2. The moisture content of the samples decreased to 0.10 kg [H2O] kg -1 [DM] in about 26 to 77 min and 27 to 85 min, depending on the applied intermittent microwave power for organic and conventional sweet red pepper shreds, respectively ( Figure 2, Table 3). It was found that increasing the applied microwave power diminished the drying time significantly (p < 0.05). Compared to organic peppers, drying time of the conventional pepper shreds lasted 1 to 8 min longer. Except 150 W, no substantial difference was found between the drying times of organic and conventional pepper samples dried at 300 and 450 W power levels. Mean cavity temperature was found to be higher in conventional red pepper, probably due to the longer drying time (Table 1).  It is clearly seen that the drying rate was in an increasing trend at the early stage of the drying process (Figure 3). At 150 and 300 W, a relatively longer constant drying rate period was observed (no constant drying rate period at 450 W). In addition, the drying rate was in a decreasing trend (falling rate period) at the final stage of the drying process. After a short heating process during the early stage of drying, intermittent microwave drying process at 450 W (PR = 1.67; SIMP = 3.0 W g −1 ) for organic and conventional pepper shreds, the drying rate increased to a maximum and then, decreased without a distinct constant drying rate period. On the contrary, a relatively long constant rate period was visible at lower specific powers (1.0 and 2.0 W g −1 ), which corresponds to higher PR levels (PR = 4.93 for 150W and PR = 2.47 for 300 W). As PR increased, the length of the constant drying rate period increased (Figure 3). This phenomenon could be due to the longer MW power off time (Toff), which provided longer rest time for better moisture and temperature distribution inside the  It is clearly seen that the drying rate was in an increasing trend at the early stage of the drying process (Figure 3). At 150 and 300 W, a relatively longer constant drying rate period was observed (no constant drying rate period at 450 W). In addition, the drying rate was in a decreasing trend (falling rate period) at the final stage of the drying process. After a short heating process during the early stage of drying, intermittent microwave drying process at 450 W (PR = 1.67; SIMP = 3.0 W g −1 ) for organic and conventional pepper shreds, the drying rate increased to a maximum and then, decreased without a distinct constant drying rate period. On the contrary, a relatively long constant rate period was visible at lower specific powers (1.0 and 2.0 W g −1 ), which corresponds to higher PR levels (PR = 4.93 for 150 W and PR = 2.47 for 300 W). As PR increased, the length of the constant drying rate period increased (Figure 3). This phenomenon could be due to the longer MW power off time (T off ), which provided longer rest time for better moisture and temperature distribution inside the product until the following MW on time (T on ). These findings are supported by various intermittent microwave drying studies [19,22,23,26,45,46]. AgriEngineering 2020, 3 FOR PEER REVIEW 7 product until the following MW on time (Ton). These findings are supported by various intermittent microwave drying studies [19,22,23,26,45,46].

Modeling of Drying Curves
The experimental moisture contents on a dry weight basis at different times during the intermittent microwave drying (IMD) process were transformed to moisture ratio (MR) values and fitted against the drying time. Fitting ability of eleven thin layer drying models were assessed based on the parameters of the standard error of estimates (SEE), the residual sum of squares (RSS), and the coefficients of determination (R 2 ) ( Table 4). The most suitable model for the microwave drying kinetics of sweet red pepper shreds was determined based on the highest R 2 value and lowest RSS and SEE values. Among the eleven drying models tested in the study, the Midilli model (Model 5) presented the best fit for all drying data points for organic and conventional peppers, with values for the R 2 greater than 0.9986, the SEE of lower than 0.0135 and the RSS of lower than 0.0148 (Table4). The drying coefficient k had higher values as a result of the increase in applied intermittent microwave power (Table 5). These findings were consistent with the drying rate data that followed a similar trajectory. Validation of the Midilli model was depicted in Figure 4, which shows predicted data closely positioned on and near the 1:1 ratio straight line.

Modeling of Drying Curves
The experimental moisture contents on a dry weight basis at different times during the intermittent microwave drying (IMD) process were transformed to moisture ratio (MR) values and fitted against the drying time. Fitting ability of eleven thin layer drying models were assessed based on the parameters of the standard error of estimates (SEE), the residual sum of squares (RSS), and the coefficients of determination (R 2 ) ( Table 4). The most suitable model for the microwave drying kinetics of sweet red pepper shreds was determined based on the highest R 2 value and lowest RSS and SEE values.
Among the eleven drying models tested in the study, the Midilli model (Model 5) presented the best fit for all drying data points for organic and conventional peppers, with values for the R 2 greater than 0.9986, the SEE of lower than 0.0135 and the RSS of lower than 0.0148 ( Table 4). The drying coefficient k had higher values as a result of the increase in applied intermittent microwave power (Table 5). These findings were consistent with the drying rate data that followed a similar trajectory. Validation of the Midilli model was depicted in Figure 4, which shows predicted data closely positioned on and near the 1:1 ratio straight line.

Effective Moisture Diffusivity (Deff) and Activation Energy (Ea)
The effective moisture diffusivity (Deff) and activation energy (Ea) values for the organic and conventional sweet red pepper shreds dried with three different applied intermittent microwave powers were given in Table 6. It was seen that increasing the applied microwave power increased the Deff values considerably. Higher microwave powers speed up the water molecules and elevate the vapor pressure inside the product to evaporate faster and hence, provide more rapid decrease in the moisture content corresponding to higher values of Deff [47][48][49]. Depending on the applied microwave power, the Deff values of organic and conventional pepper shreds ranged from 59.69 × 10 −10 to 182.01 × 10 −10 m 2 s −1 and from 59.11 × 10 −10 to 181.01 × 10 −10 m 2 s -1 , respectively (Table 6). No distinct difference was observed between the Deff values of organic pepper and conventional pepper shreds dried at 150, 300 and 450 W applied microwave powers. Table 6. Effective moisture diffusion (Deff) coefficients and equations for different applied intermittent microwave powers applied to organic and conventional sweet red peppers.

Effective Moisture Diffusivity (D eff ) and Activation Energy (E a )
The effective moisture diffusivity (D eff ) and activation energy (E a ) values for the organic and conventional sweet red pepper shreds dried with three different applied intermittent microwave powers were given in Table 6. It was seen that increasing the applied microwave power increased the D eff values considerably. Higher microwave powers speed up the water molecules and elevate the vapor pressure inside the product to evaporate faster and hence, provide more rapid decrease in the moisture content corresponding to higher values of D eff [47][48][49]. Depending on the applied microwave power, the D eff values of organic and conventional pepper shreds ranged from 59.69 × 10 −10 to 182.01 × 10 −10 m 2 s −1 and from 59.11 × 10 −10 to 181.01 × 10 −10 m 2 s −1 , respectively (Table 6). No distinct difference was observed between the D eff values of organic pepper and conventional pepper shreds dried at 150, 300 and 450 W applied microwave powers. Table 6. Effective moisture diffusion (D eff ) coefficients and equations for different applied intermittent microwave powers applied to organic and conventional sweet red peppers. The D eff values established in this work were within the range from 10 −11 to 10 −9 m 2 s −1 for various biological materials [50,51], very similar [48] and lower [13,[52][53][54] than that of the red or green peppers reported by several authors ( Table 7). The variations could be due to differences in the drying conditions and physico-chemical properties of dried materials such as cultivar, composition, slice thickness and stage of ripening [55]. Table 7. Effective moisture diffusivities (D eff ) and activation energies (E a ) of peppers dried by intermittent microwave as compared to the values in previous studies.

Products
Applied The pre-exponential factor of the Arrhenius equation (D 0 ) explaining moisture diffusivity when temperature goes to infinity [56] was found to be the same for both product types ( Table 6). The same trend was determined for the activation energy (E a ) values, which were computed from the slope of the Equation (6) by plotting ln(D eff ) against m/P a . The plots showed straight lines for the studied applied power range, which indicated Arrhenius dependence ( Figure 5). Thus, the E a values established from the slope of these lines were 1.62 and 1.63 W g −1 for the organic and conventional sweet red pepper samples, respectively (Table 7).
AgriEngineering 2020, 3 FOR PEER REVIEW 9 The Deff values established in this work were within the range from 10 −11 to 10 −9 m 2 s −1 for various biological materials [50,51], very similar [48] and lower [13,52,53,54] than that of the red or green peppers reported by several authors ( Table 7). The variations could be due to differences in the drying conditions and physico-chemical properties of dried materials such as cultivar, composition, slice thickness and stage of ripening [55].
The pre-exponential factor of the Arrhenius equation (D0) explaining moisture diffusivity when temperature goes to infinity [56] was found to be the same for both product types ( Table 6). The same trend was determined for the activation energy (Ea) values, which were computed from the slope of the Equation (6) by plotting ln(Deff) against m/Pa. The plots showed straight lines for the studied applied power range, which indicated Arrhenius dependence ( Figure 5). Thus, the Ea values established from the slope of these lines were 1.62 and 1.63 W g −1 for the organic and conventional sweet red pepper samples, respectively (Table 7).  The Ea value determines the sensitivity of diffusivity against temperature. Higher Ea values indicate higher sensitivity of the diffusivity to the temperature [56]. The similarity between the Ea values of organic and conventional peppers signifies that organic or conventional growing practice did not significantly alter the structural properties of the sweet red pepper samples. Furthermore, both the organic and conventional pepper shreds showed the same resistance to the moisture transported in the drying material as a result of intermittent microwave drying. The drying kinetic profiles and the calculated Deff values given above strongly support this statement. The Ea values of the red pepper shreds obtained in the current study were similar [52,54] and much lower [53] as compared to the Ea values reported by several authors for green and red peppers (Table 7). Differences can be attributed to different factors including cultivar, physico-chemical properties of The E a value determines the sensitivity of diffusivity against temperature. Higher E a values indicate higher sensitivity of the diffusivity to the temperature [56]. The similarity between the E a values of organic and conventional peppers signifies that organic or conventional growing practice did not significantly alter the structural properties of the sweet red pepper samples. Furthermore, both the organic and conventional pepper shreds showed the same resistance to the moisture transported in the drying material as a result of intermittent microwave drying. The drying kinetic profiles and the calculated D eff values given above strongly support this statement. The E a values of the red pepper shreds obtained in the current study were similar [52,54] and much lower [53] as compared to the E a values reported by several authors for green and red peppers (Table 7). Differences can be attributed to different factors including cultivar, physico-chemical properties of dried material, composition, design features of drying equipment, microwave power level, slice thickness, growing conditions, ripening stage, etc.

Influence of Applied Microwave Power on the Color of Powdered Red Pepper Samples
The relations between the applied intermittent microwave power and color parameters of fresh and dried red pepper shreds were given in Table 8. The L* and b* values of the organic and conventional fresh samples did not show any statistically significant difference. However, redness (a*) and a*/b* ratios of fresh organic and conventional samples were different (p < 0.05), which signifies that the color of fresh conventional samples was deeper in red as compared to the organic samples (Table 8). Thus, the differences between organic and conventional samples were due to a difference in a* parameter from the fresh samples.
The L* value of the dried and powdered red peppers was significantly higher than that of the fresh peppers (p < 0.05). It was observed that, as compared to fresh product, the redness values of dried peppers increased first and then decreased depending on the increase in applied microwave power. In terms of microwave treatments, 450 W always showed lower a* values, followed by 300 W, while 150 W demonstrated higher values of a* and a*/b* for organic and conventional products as compared to other microwave powers. The redness (a*) values of organic and conventional red peppers dried at 150 W microwave power were noticeably higher than that of fresh red peppers (p < 0.05). Beside this, no significant difference was determined between the a* values of fresh and dried organic pepper shreds dried at 300 W power level.
Commonly used quality criteria for dried red pepper was red color intensity [57,58], which comes from ketocarotenoids, capsanthin and capsorubin. Moreover, some researchers reported that the dried red peppers having a higher ratio of redness to yellowness (a*/b*) were considered as more preferable [59]. The a*/b* values were found to be lower in the current study in both fresh and dried products as compared to the findings of Ergunes and Tarhan [59] (who reported up to 3.93) and this difference could be due to some factors such as pepper type, production method, drying technique, and maturity level, etc. It is clear that the L* values of both organic and conventional fresh samples were significantly enhanced after microwave drying process in the present study (p < 0.05).
Compared to the fresh product color values, it was determined that the change in the redness values remained at a limited level, whereas the yellowness values increased to a higher extent. The highest color difference values (∆L*, ∆a*, ∆b* and ∆E*) were obtained at lower microwave power levels (Table 8). On the other hand, microwave drying at 150 and 300 W for organic peppers and at 150 W for conventional red peppers yielded the highest ∆L*, ∆a* and a*/b* values. This implies that these pepper powders were deeper and brighter in red color (Table 8). Hence, intermittent microwave drying at 150 and 300 W for organic peppers and at 150 W for conventional red peppers can be evaluated as the most suitable drying applications because these treatments gave brighter and redder pepper powders as compared to fresh peppers. Table 8. Color parameters of fresh and intermittent microwave-dried and powdered organic and conventional red pepper samples (n = 9; mean ± std. dev.).

Product
Applied * Different letters (a-f) in same column specify significant differences (p < 0.05).

Conclusions
The results revealed that drying of the conventional pepper shreds lasted 1 to 8 min longer as compared to organic peppers. Except 150 W (1.0 Wg −1 ), no substantial difference was determined between the drying times of organic and conventional red pepper samples dried at 300 (2.0 Wg −1 ) and 450 W (3.0 Wg −1 ) power levels.
The Midilli model provided the best fit for all drying data points for both organic and conventional peppers.
Depending on the applied microwave power, the D eff values of organic and conventional red pepper shreds ranged from 59.69 × 10 −10 to 182.01 × 10 −10 m 2 s −1 and from 59.11 × 10 −10 to 181.01 × 10 −10 m 2 s −1 , respectively. No distinct difference was found between the D eff values of organic and conventional pepper shreds dried at 150, 300 and 450 W applied microwave powers. The activation energy (E a ) was found to be 1.62 and 1.63 W g −1 for the organic and conventional samples. Both the pre-exponential factor of the Arrhenius equation (D 0 ) and activation energy (E a ) values were found as almost identical for both product types. Consequently, close similarity among the characteristics drying curves, D eff and E a values signifies that organic or conventional growing practice did not significantly alter the structural properties of the sweet red pepper samples. Both the organic and conventional pepper shreds showed the same resistance to the moisture transported in the pepper samples as a result of intermittent microwave drying (IMD).
The color of fresh conventional red pepper samples was deeper in red as compared to the organic samples. IMD at 150 (1.0 Wg −1 ) and 300 W (2.0 Wg −1 ) for organic red peppers and at 150 W (1.0 Wg −1 ) for conventional peppers yielded the highest ∆L*, ∆a* and a*/b* values, which implies that these pepper powders were deeper and brighter in red color. Hence, IMD at 150 and 300 W for organic red peppers and 150 W for conventional red peppers can be evaluated as the suitable drying applications, as these treatments gave brighter and redder pepper powders as compared to fresh peppers.
Due to the increasing demand for organic products, future studies are needed on the drying kinetics, color parameters, aroma profiles and sensory attributes of other organic products as compared to the conventional products.