Enhancing Oil-Uptake Efficiency with an Alkyl Polyglycoside–Dodecanol Formulation

: This study provides valuable insights into biobased surfactant systems, shedding light on their behavior and potential applications in cleaning and oil recovery processes. By combining the alkyl polyglycoside Triton ® CG-110 with C 12 OH fatty alcohol, a promising strategy emerges, enhancing the efficiency of surfactant-based formulations. This innovative approach paves the way for sustainable solutions in diverse industrial applications. A rheological analysis of the formulations containing C 12 OH demonstrated a Newtonian-like behavior of up to 3.2 v / v % of Triton, while a viscoelastic response was observed in a system containing 6.4 v / v % of Triton. Self-diffusion nuclear magnetic resonance revealed the formation of larger aggregates with C 12 OH, diverging from the classical spherical micellar solution. Moreover, cleaning efficiency tests highlighted C 12 OH’s significant enhancement of the surfactant system’s oil-uptake capacity. This study identified the optimum formulation point, corresponding to the Winsor III microemulsion phase, in samples containing C 12 OH. This pivotal discovery showcases the potential of tailored surfactant blends, indicating a path toward greener and more effective industrial practices.


Introduction
Biosurfactants, as an environmentally sustainable alternative to conventional surfactants, offer the potential to mitigate the environmental impact caused by the escalating production of industrial surfactant-containing formulations [1,2].In recent years, heightened concern for environmental issues has directed scientific and technological research efforts.The imperative to safeguard human and environmental well-being while reducing reliance on nonrenewable resources has stimulated investigations into the discovery and development of novel sustainable molecules.These molecules should demonstrate high biocompatibility and biodegradability, originating from either natural sources or a synthetic approach grounded in the principles of green chemistry [3][4][5][6].
Rha surfactants-comprising a hydrophilic group involving one or two (L)-rhamnose molecules with a glycosidic linkage to a hydrophobic group composed of one or two β-hydroxy fatty acids-have emerged as promising contenders for the partial or complete substitution of anionic surfactants across a range of industrial formulations [1,2].However, the utilization of rhamnolipids is hindered by their elevated production costs, attributed to fermentation and product purification processes [46][47][48].In contrast, APG surfactants offer a cost-effective alternative.
APGs have been utilized in the composition of water-in-oil (W/O) nanoemulsions with various solvent systems, serving as specialized detergents for the precise removal of various graffiti coatings [61].In the realm of detergency, APGs have been employed as degreasing agents [62] and have even been utilized to remove radioactive contamination in low-temperature environments [63].As non-ionic surfactants, APGs possess impressive eco-friendly attributes and have emerged as promising candidates for chemical flooding applications, particularly in high-temperature, high-salinity reservoirs.Unlike other non-ionic surfactants containing propylene oxide (PO) and ethylene oxide (EO) structures, APGs do not exhibit a cloud point at elevated temperatures in the presence of salts, making them particularly interesting for hightemperature, high-salinity reservoirs where traditional surfactants tend to adsorb on carbonate surfaces [55,64].Studies indicate that APGs show lower adsorption on carbonate surfaces compared with anionic surfactants like alkyl ether carboxylate [64,65].
Ultra-low interfacial tension in brine/alkane or brine/xylene systems can be seen in APG formulations.Balzer [66] observed ultra-low interfacial tension between water and three different model oils in the presence of APG surfactants, as did Kutschmann et al. and Kahlweit et al. with linear alcohols as co-solvents [67,68].Dari et al. reported that it is possible to stabilize W/W emulsions using a lamellar gel network based on different APGs and fatty alcohols [69].The effect of alcohol on classical surfactants has been a subject of investigation for decades.For instance, dodecanol on dodecylamine molecules forms stable clusters at the air/water interface through van der Waals forces between the hydrophobic alkyl chains and hydrogen bonding between the head groups [70].Such interactions result in a lower critical micelle concentration (CMC), reduced interfacial tension, and more stable micelles.Colafemmina et al. investigated the effect of fatty alcohol mixtures inserted into a CTAC surfactant, indicating highly different effects depending on the cooling ramp rate used after mixing [71].
We present a formulation involving the APG surfactant Triton ® CG-110, an octyl/decyl polyglucoside, combined with the fatty alcohol dodecanol that is able to enhance oil uptake.Dodecanol is a highly surface-active compound that significantly influences interfacial tension when co-adsorbed with Triton ® CG-110.The impact of dodecanol on Triton ® CG-110 concentrations was evaluated using both stationary and oscillatory rheology techniques, along with 1 H self-diffusion NMR.We assess the surfactant's ability to capture oils, both in the presence and absence of fatty alcohol.This study has the potential to enhance oil recovery and find applications in household cleaning.
The purchased surfactant might contain traces of 1-decanol and 1-octanol.In the following text, Triton ® CG-110 will be indicated as C 8-10 G m , where 8-10 are the number of atoms in the hydrocarbon chain, and "m" is a non-definite number of pyranose (G) units in oligomers."C 12 OH" will denote the fatty alcohol 1-dodecanol.The critical micellar concentration (CMC) is at 1748 ppm (~0.17 v/v%) at a temperature of 25 • C [72,73].

Formulations
The Triton ® CG-110 samples were prepared by blending the surfactant solution with distilled H 2 O at concentrations of 1%, 5%, and 10% by volume relative to the initial solution.In a second set of samples, an additional 0.25%, 1.25%, and 2.5% by volume of C 12 OH was added.The C 12 OH acts as a co-surfactant.
The surfactant and the C 12 OH were mixed at 70 • C, applying a shear rate of 1000 s −1 .Subsequently, the system was cooled down at a rate of 1 • C/min while maintaining a shear rate of 100 s −1 .Considering the surfactant concentration in the initial solution of approximately 64% by weight, the resulting ratio of surfactant to fatty alcohol was approximately 2.56:1.The investigated samples are reported in Table 1.The standard uncertainties of 0.1 v/v% in the concentrations are estimated based on the precision of the micropipette.The v/v% concentration is obtained by considering the initial volume of aliquots of Triton ® CG-110.

Stationary and Oscillatory Rheology
Stationary and oscillatory rheological measurements were carried out using the MCR302evolution stress-controlled rheometer (Anton Paar Gmbh, Graz, Austria) equipped with Taylor−Couette geometry, i.e., concentric cylinder geometry (inner diameter of 16.662 mm and a gap of 0.704 mm).For sample CG10C, a double-wall concentric cylinder geometry was utilized, having stationary inner and outer cylinder diameters of 23.824 mm and 27.586 mm, respectively.The inner and outer rotor diameters were 24.660 mm and 26.650 mm, respectively.The temperature was controlled by a Peltier system (±1 • C), and a water-bath circulator was used as a reference.
The stationary experiments were used to prepare the samples containing fatty alcohol, as described in Section 2.2.Moreover, they were performed at 25 • C by incrementally increasing the shear rate, .γ, and obtaining the apparent viscosity, η .γ , from the measured shear stress (flow curve).All samples were investigated within a range of shear rates from 0.1 to 100 s −1 .The Carreau-Yasuda model, [74] was adopted to determine the zero-shear viscosity of non-Newtonian pseudoplastic samples.The equation for the Carreau-Yasuda model is as follows: where η . γ → 0 and η .γ → ∞ represent the zero-shear and infinity-shear viscosities, respectively."a" is a constant that determines the curvature of the transition region between the lower and higher shear rates, while "λ" has the dimension of time and represents the characteristic time of the system."n" has the same meaning as in the Herschel-Bulkley model; a Newtonian behavior is characterized by a flow index of 1, n = 1, whereas the shear-thinning and shear-thickening non-Newtonian behaviors are characterized by n < 1 and n > 1, respectively.
Small amplitude oscillatory shear tests provided insights into the linear viscoelastic behavior of materials through the determination of the complex shear modulus as a function of the oscillatory angular frequency, ω: where G ′ (ω) and G ′′ (ω), in the following indicated as G ′ and G ′′ , are the elastic and viscous moduli, respectively.Frequency sweep tests were conducted between 10 −1 and 10 2 rad/s in the linear viscoelastic regime.

1 H Self-Diffusion NMR
The NMR experiments were conducted using an Agilent/Varian VNMRS 500 MHz spectrometer equipped with the OneNMR probe.The 1 H NMR spectra were acquired using the PRESAT pulse sequence for water suppression.Self-diffusion 1 H NMR measurements were carried out by employing the DOSY Gradient-Compensated Stimulated Echo with Spin Lock (DgcsteSL) [75] to measure water self-diffusion and the PRESAT sequence (DgcsteSL_dpfgse) to determine the self-diffusion coefficients of the surfactant while suppressing the water signal.The field gradient pulses, denoted as g, ranged from 0.02 to 0.64 Tm −1 .The samples were maintained at a temperature of 25 • C. The resulting spin-echo decays were evaluated following the well-known Stejskal and Tanner equation [76]: where I represents the echo amplitude, and I 0 is the amplitude at g = 0. γ represents the proton's gyromagnetic ratio; ∆ is the gradient pulse separation, ranging from 70 ms to 130 ms; and the gradient pulse duration, δ, varied from 2 ms to 10 ms to explore different time scales and observe echo decays in the water or surfactant.D stands for the apparent self-diffusion coefficient.Equation (3) can also be expressed in terms of b, the diffusion attenuation factor, which contains information regarding the gradient duration and strength used to produce diffusion-weighted spectra.The echo decays for water self-diffusion were obtained at 4.8 ppm, while the surfactant self-diffusion coefficients were determined by integrating the signal from 0.5 to 4.5 ppm.

Cleaning Efficiency and Qualitative Oil-Uptake Performance
The cleaning efficiency was evaluated using a cleaning performance procedure based on IKW recommendations, which can also be interpreted as the amount of oil that the system is capable of absorbing (oil uptake).A sample of greasy soil was applied to a stainless-steel tile, which was then baked and aged at 135 • C for 2 h before being used for the cleaning assessment.The stainless-steel tiles were treated with a solution of potassium hydroxide (0.08 wt/vol%) and ethanol before use.The greasy soil consisted of oils and soil in a ratio of 4:1.Specifically, the oil was composed of peanut oil, sunflower oil, and corn oil, while the HSW soil was primarily composed of humus, cement, silica gel, and clay.The resulting negatively charged organic matter composition included fatty acids; carbohydrates; and, to a lesser extent, aromatics.The mixture was such that it could be perceived as used cooking oil.The soiled stainless-steel tiles were placed in Petri dishes and covered with pollutant-removal solutions for 18 h.The soiled stainless-steel tiles were weighed using an analytical balance before and after the application of the cleaning solutions.
To evaluate the oil uptake of the surfactant and the combined surfactant and fatty alcohol (co-surfactant) system, petroleum ether was added to form microemulsions.The oil was added to the surfactant and to the surfactant plus the co-surfactant solutions in water.

The Effect of Dodecanol on Triton ® CG-110 Micellar Phase
The Triton ® CG-110 and C 8-10 G m surfactants exhibit a critical micelle concentration (CMC) of approximately 0.17 v/v% at 25 • C. The pseudo-binary phase diagram in water indicates a single micellar phase, L1 [72,73].Figure 1A illustrates the elastic modulus (G ′ ) and viscous modulus (G ′′ ) as functions of angular frequency for the CG1, CG5, and CG10 samples.The frequency sweep tests show overlapping results, resembling Newtonian-like solution behavior, confirming the presence of pure micelles for all investigated concentrations.
The addition of C 12 OH significantly affects the frequency sweep measurements.In CG1C and CG5C, G ′′ surpasses G ′ across all angular frequencies, with G ′′ an order of magnitude higher compared with samples without C 12 OH, as shown in Figure 1B.Additionally, CG1C and CG5C exhibit Newtonian-like behavior in their apparent viscosity, as depicted in Figure 1C.
Conversely, the introduction of C 12 OH to the CG10C sample results in viscoelastic behavior, as shown in Figure 2B.The frequency sweep of CG10C demonstrates non-Maxwellian behavior, with the slopes of G ′ and G ′′ at low frequency, deviating significantly from the expected values of two and one, respectively.The flow curve for this system indicates shear-thinning behavior, particularly with no apparent yield stress, classifying the system as pseudoplastic, as shown in Figure 1D.Applying the Carreau-Yasuda model (Equation ( 1)) to the pseudoplastic system yields a flow index (n) of 0.49, a zero-shear viscosity of 1613 ± 78 mPa, and a relaxation time (λ) of 72 ± 12 s.

Self-Diffusion NMR and Obstruction Factor
The 1 H NMR spectra of CG5 and CG5C are shown in Figure 2A.The resonances of the surfactant head (polyglycosides) are not affected by the presence of the fatty alcohol, while the intensities are visibly affected in the alkyl region (from 0.5 to 1.8 ppm), changing the intensity ratio between the polyglycoside region and the alkyl region as expected.Moreover, some impurities are appreciable in the CG5 spectrum, but they are not appreciable in the CG5C because of the high resonance intensities.

Self-Diffusion NMR and Obstruction Factor
The 1 H NMR spectra of CG5 and CG5C are shown in Figure 2A.The resonances of the surfactant head (polyglycosides) are not affected by the presence of the fatty alcohol, while the intensities are visibly affected in the alkyl region (from 0.5 to 1.8 ppm), changing the intensity ratio between the polyglycoside region and the alkyl region as expected.Moreover, some impurities are appreciable in the CG5 spectrum, but they are not appreciable in the CG5C because of the high resonance intensities.
1 H self-diffusion NMR was employed to evaluate the amount of C 12 OH entrapped in the surfactant and to elucidate the kind of surfactant-alcohol assembly.Figure 2B shows the water self-diffusion coefficients for all investigated samples with respect to the total volume fraction considering the surfactant volume fraction plus the fatty alcohol content of the samples containing fatty alcohol.It is worth noting that all echo decays were fitted with a single-exponential decay equation (Equation ( 3)).Clearly, water self-diffusion was strongly affected by the presence of the fatty alcohol even before reaching the CG10 sample (volume fraction of 0.064).
Equation ( 3), used to estimate the water self-diffusion NMR coefficient, is effective for pure isotropic systems such as the micellar phase, while for anisotropic systems, the following holds [77]: where f is the obstruction factor, whose value is 0 < f < 1, which accounts for the geometrical restrictions to water self-diffusion.For any phase, the relation between water self-diffusion and the surfactant volume fraction can be expressed as where P b is the amount of water bound to interfaces with a self-diffusion equal to D b , and D w is the self-diffusion of free water (2.29 × 10 −9 m 2 /s).However, P b is not directly available from experimental measurements, but if we have two lyotropic mixtures, i and j, belonging to the same phase or micellar solution but with a slightly different composition, a simple relation can be found via elementary stoichiometric considerations, locking the fractions P i and P j to the water weight fractions W i and W j .
Rewriting Equation ( 5) for i and j and considering Equation ( 6), we can obtain the obstruction factor as a function of known quantities: If we consider 5 and 10 v/v% of C 8-10 G m (CG5 and CG10) to be our i and j samples, we obtain f = 0.99, but it reduces to 0.86 considering 1 and 5 v/v% C 8-10 G m + C 12 OH (CG1C and CG5C) and to 0.44 considering 5 v/v% and 10 v/v% of C 8-10 G m + C 12 OH (CG5C and CG10C).
The surfactant self-diffusion coefficients, shown in Figure 2C as a function of the total volume fraction, were determined by fitting the echo decay signals with a singleexponential decay equation (Equation ( 3)).This implies that the fatty alcohol and the surfactant are located in the same assembly.The surfactant self-diffusion decreases as the total volume fraction increases, suggesting an increase in the size of the aggregates.
Assuming a spherical shape for the micelles in the samples without C 12 OH, we calculated hydrodynamic radii of 1.3 ± 0.5 nm, 1.9 ± 0.4 nm, and 2.7 ± 0.2 nm for CG1, CG5, and CG10, respectively, using the Stokes-Einstein equation.These results align with the DLS data in Figure S1, where a hydrodynamic radius of 2.8 ± 0.4 nm is observed for both CG5 and CG10.
However, the samples containing C 12 OH deviate from the classical spherical micellar solution, as indicated by the obstruction factor.Consequently, the Stokes-Einstein equation cannot be properly applied even though the self-diffusion coefficient is lower than the system without C 12 OH, implying the presence of larger aggregates.

Cleaning Efficiency and Oil-Uptake
The samples, both with and without C 12 OH, were tested for cleaning efficiency.Contaminated stainless steel tiles were immersed in the respective systems and placed in Petri dishes for 18 h, as shown in Figure 3A-F.The cleaning efficiency, indicated by weight loss or oil uptake, is reported in Figure 3G.The oil uptake was estimated using the following formula: where W f represents the final weight of the contaminated stainless-steel tiles after 18 h of treatment with the testing sample, W in is the initial weight of the contaminated stainlesssteel tiles, and W p represents the weight of the clean stainless-steel tiles.Even when increasing the surfactant concentration without C12OH, the results indicate a lower cleaning efficiency (see Figure S2).
The system containing 1 v/v% of C8-10Gm and 0.25 v/v% of C12OH (CG1C) demonstrated the highest cleaning efficiency, approximately 57%, surpassing commercial systems and newly developed formulations [78].A further increase in surfactant concentrations leads to a decrease in efficiency because of the formation of a viscoelastic matrix.The CG1 without alcohol contains micelles with relatively low cleaning efficiency.Increasing the surfactant concentration increases cleaning efficiency as well but with less effectiveness compared with the systems containing C12OH.
Samples were collected to measure the self-diffusion coefficients at the end of the cleaning experiments (Figure 4).The line shape of the 1 H NMR spectra was affected by the presence of contaminants (Figure 4A).Particularly in systems containing C12OH, the selfdiffusion coefficients were significantly affected.For samples without C12OH, after collecting contaminants, monoexponential echo decays were observed, enabling the direct application of Equation (3).However, in samples with C12OH, a double-exponential decay (blue line) had to be applied since the monoexponential decay (red dotted line) did not fit the data properly (Figure 4B).Even when increasing the surfactant concentration without C 12 OH, the results indicate a lower cleaning efficiency (see Figure S2).
The system containing 1 v/v% of C 8-10 G m and 0.25 v/v% of C 12 OH (CG1C) demonstrated the highest cleaning efficiency, approximately 57%, surpassing commercial systems and newly developed formulations [78].A further increase in surfactant concentrations leads to a decrease in efficiency because of the formation of a viscoelastic matrix.The CG1 without alcohol contains micelles with relatively low cleaning efficiency.Increasing the surfactant concentration increases cleaning efficiency as well but with less effectiveness compared with the systems containing C 12 OH.
Samples were collected to measure the self-diffusion coefficients at the end of the cleaning experiments (Figure 4).The line shape of the 1 H NMR spectra was affected by the presence of contaminants (Figure 4A).Particularly in systems containing C 12 OH, the self-diffusion coefficients were significantly affected.For samples without C 12 OH, after collecting contaminants, monoexponential echo decays were observed, enabling the direct application of Equation (3).However, in samples with C 12 OH, a double-exponential decay (blue line) had to be applied since the monoexponential decay (red dotted line) did not fit the data properly (Figure 4B).The self-diffusion coefficients decreased with increasing total volume fraction.Specifically, the two self-diffusion coefficients for samples containing C12OH are indicated as black-and gray-filled circles in Figure 4C.
To further evaluate the oil-uptake capacity of the investigated samples at 1 v/v% of C8-10Gm with and without C12OH, petroleum ether was gradually added to the respective samples (refer to Figure 5).The quantity of oil retained before reaching the Winsor III microemulsion phase is considered the maximum oil uptake, aligning with the optimized formulation concept introduced for enhanced oil recovery (EOR) [79].It is well established that the optimal formulation corresponds to a minimum interfacial tension, described when the hydrophilic-lipophilic deviation (HLDN) equals zero [80][81][82], indicating the Winsor III phase [83].In our case, Winsor III is achieved at a volume ratio of 2:0.300 for the CG1C sample (Figure 5H), but it is not observed for the corresponding sample without C12OH, CG1 (Figure 5D).However, the achieved Winsor III is referred to as "apparent" because the central phase does not form a bicontinuous structure, a behavior documented in other studies involving different systems [84].Furthermore, after an extended period of 96 h, a Winsor II phase is observed (Figure 5I).The self-diffusion coefficients decreased with increasing total volume fraction.Specifically, the two self-diffusion coefficients for samples containing C 12 OH are indicated as black-and gray-filled circles in Figure 4C.
To further evaluate the oil-uptake capacity of the investigated samples at 1 v/v% of C 8-10 G m with and without C 12 OH, petroleum ether was gradually added to the respective samples (refer to Figure 5).The quantity of oil retained before reaching the Winsor III microemulsion phase is considered the maximum oil uptake, aligning with the optimized formulation concept introduced for enhanced oil recovery (EOR) [79].It is well established that the optimal formulation corresponds to a minimum interfacial tension, described when the hydrophilic-lipophilic deviation (HLD N ) equals zero [80][81][82], indicating the Winsor III phase [83].In our case, Winsor III is achieved at a volume ratio of 2:0.300 for the CG1C sample (Figure 5H), but it is not observed for the corresponding sample without C 12 OH, CG1 (Figure 5D).However, the achieved Winsor III is referred to as "apparent" because the central phase does not form a bicontinuous structure, a behavior documented in other studies involving different systems [84].Furthermore, after an extended period of 96 h, a Winsor II phase is observed (Figure 5I).

Discussion
The APG micellar phase has been extensively discussed in the literature.While micelles might be spherical and homogeneous in size at the CMC [85,86], they become larger and heterodisperse with increasing concentrations.Micelles have been demonstrated to be anisotropic in shape [87,88].Using the 1 H NMR self-diffusion coefficient of an APG surfactant with an eight-carbon alkyl chain and considering the contribution effects and the assumption that micelle size does not change with concentration, it has been demonstrated that cylindrical micelles, with a cylinder radius of 2.16 nm and an axial ratio of 0.45 nm, are more suitable.
The water self-diffusion obstruction factor of spherical micelles was estimated to be 1/(1 + (Φ/2)), where Φ is the volume fraction 89 , implying that, for our volume fraction, 0.96 < f < 0.99, whereas the obstruction of cylinders is 1/(1 + Φ), implying that for our volume fraction is 0.92 < f < 0.99 for the samples without C12OH.In the concentration range investigated, we cannot distinguish between spherical or cylindrical micelles.On the other hand, it is clear that, from 1 to 10 v/v%, there is no increase in size (Figures 2C and S1) or change in Newtonian behavior (Figure 1A,C).
The effect of C12OH on the micellar shape leads to an obstruction factor below the 0.92 value of the micelles with a cylindrical shape.This could be due to the formation of a worm-like micelle network, but the frequency sweep is far from being Maxwellian-like, suggesting a more intricate structure.The frequency sweep is not typical of a lamellar phase either [90][91][92] and is not birefringent.Further investigation is needed to characterize the obtained viscoelastic system.

Discussion
The APG micellar phase has been extensively discussed in the literature.While micelles might be spherical and homogeneous in size at the CMC [85,86], they become larger and heterodisperse with increasing concentrations.Micelles have been demonstrated to be anisotropic in shape [87,88].Using the 1 H NMR self-diffusion coefficient of an APG surfactant with an eight-carbon alkyl chain and considering the contribution effects and the assumption that micelle size does not change with concentration, it has been demonstrated that cylindrical micelles, with a cylinder radius of 2.16 nm and an axial ratio of 0.45 nm, are more suitable.
The water self-diffusion obstruction factor of spherical micelles was estimated to be 1/(1 + (Φ/2)), where Φ is the volume fraction [89], implying that, for our volume fraction, 0.96 < f < 0.99, whereas the obstruction of cylinders is 1/(1 + Φ), implying that for our volume fraction is 0.92 < f < 0.99 for the samples without C 12 OH.In the concentration range investigated, we cannot distinguish between spherical or cylindrical micelles.On the other hand, it is clear that, from 1 to 10 v/v%, there is no increase in size (Figure 2C and Figure S1) or change in Newtonian behavior (Figure 1A,C).
The effect of C 12 OH on the micellar shape leads to an obstruction factor below the 0.92 value of the micelles with a cylindrical shape.This could be due to the formation of a worm-like micelle network, but the frequency sweep is far from being Maxwellian-like, suggesting a more intricate structure.The frequency sweep is not typical of a lamellar phase either [90][91][92] and is not birefringent.Further investigation is needed to characterize the obtained viscoelastic system.
Employing surfactants is a recognized approach to efficiently eliminating surface pollutants at both micro-and nanoscale levels [93].Furthermore, in the realm of enhanced oil recovery (EOR), surfactants play a crucial role [12][13][14].In both cases, a higher amount of oil is retained by the surfactant, leading to increased efficiency.The most effective oil uptake is usually achieved above the surface aggregation concentration when submonolayer, monolayer/hemimicelle, or bilayer/cylindrical micelle structures are formed at interfaces and surfaces [94].
The C 8-10 G m in water always presents a micellar phase, which can be spherical or cylindrical, showing a relatively low capacity for entrapping the oil phase (contaminants).GC1 holds approximately 12% of the oil phase, while GC10 holds approximately 24% of the oil phase.The cleaning efficiency is relatively low compared with other systems [78].Adding C 12 OH to the surfactants results in a much lower obstruction factor, indicating the presence of a more complex system that leads to pseudoplastic behavior, especially in the case of the CG10C sample.The pseudoplastic behavior is not desirable for a conventional formulation since it might interfere with the detergent's ability to penetrate surfaces effectively.When C 12 OH is added to the system, the cleaning capacity, i.e., the oil uptake, increases considerably, particularly for CP1C, accounting for approximately 57% of the oil phase.An apparent Winsor III microemulsion phase was observed by adding petroleum ether to the samples containing C 12 OH, enabling the estimation of the optimum formulation point, which is at a ratio of 2:0.300 for CG1C, while no Winsor III was observed at any time in the absence of C 12 OH.
Fatty alcohols are oleochemicals characterized by hydrophobic acyl chains and hydroxyl groups, providing them with amphiphilic properties.As such, they are useful co-surfactants in formulations.We have demonstrated that their oleochemical nature enhances the oil-uptake capacity even in the case of an alkyl polyglycoside surfactant.As such, formulations including APGs and fatty alcohols can be adopted for detergency.

Conclusions
In conclusion, our study delved into the intricate behavior of the Triton ® CG-110 micellar phase and the significant impact of C 12 OH addition.While all concentrations of Triton ® CG-110 demonstrated Newtonian-like behavior, the introduction of C 12 OH led to a viscoelastic response in CG10C, signifying a more complex system.Through advanced NMR techniques, we investigated the self-diffusion coefficients, unveiling significant alterations influenced by the presence of C 12 OH.Spherical micellar structures, common in Triton ® CG-110, transitioned into anisotropic shapes, particularly cylindrical micelles, as indicated by the obstruction factors.Moreover, our experiments highlighted the cleaning efficiency and oil-uptake capacity of the systems.Triton ® CG-110 with C 12 OH demonstrated remarkable efficiency in oil uptake at more than 50%.The addition of petroleum ether to the samples containing C 12 OH led to the formation of apparent Winsor III microemulsion phases, offering insights into the optimal formulation ratios.Finally, we explored the role of fatty alcohols as co-surfactants, emphasizing, in our preliminary evaluation, their amphiphilic nature in enhancing oil-uptake capacities, even when combined with alkyl polyglycoside surfactants.Triton ® CG-110 is still relatively expensive, but the low concentration and the use of fatty alcohols made the system cost-effective.Our findings provide valuable insights into the complex interplay of surfactant and co-surfactant systems, offering potential avenues for enhanced oil recovery strategies and efficient surface pollutant removal at both the micro-and nanoscale levels.

Figure 1 . 17 Figure 2 . 1 H
Figure 1.The elastic modulus, G ′ , and viscous modulus, G ′′ , are presented as functions of angular frequency for systems with Triton ® CG-110 at 1 v/v%, CG1; 5 v/v%, CG5; and 10 v/v%, CG10, in water (A), as well as for Triton ® CG-110 with C 12 OH in a 2.56:1 ratio as a function of surfactant concentrations for CG1C, CG5C, and CG10C (B).The red lines represent linear fits of G ′′ and G ′ with slopes of 0.5 and 0.8, respectively.The apparent viscosity as a function of shear rate is shown for all investigated systems (C), while the shear stress as a function of shear rate is presented for the system CG10C (D).The red line corresponds to the Carreau-Yasuda model, Equation (1), while the inset is a linear-linear plot.All measurements were conducted at 25 • C. Colloids Interfaces 2024, 8, x FOR PEER REVIEW 7 of 17

Figure 2 .
Figure 2. 1 H NMR spectra of the 5 v/v% of C 8-10 G m , CG5, and 5 v/v% of C 8-10 P m + 1.25 v/v% of C 12 OH, CG10 (A).Water self-diffusion (B) and surfactant self-diffusion (C) coefficients extracted from the echo decays using the Stejskal and Tanner equation, Equation (3), for all investigated samples.

Figure 3 .
Figure3.Cleaning efficiency (oil-uptake) performance test made on contaminated stainless-steel tiles using the C8-10Gm surfactant concentrations, CG1 (A), CG5 (B), and CG10 (C), and the C8-10Gm surfactant + C12OH CG1C (D), CG5C (E), and CG10C (F).Finally, weight loss of contaminants from stainless-steel tiles (previously contaminated with HVS soil and oils) after 18 h of immersion in the respective solutions (G).The weight loss can be observed qualitatively as the amount of oil uptake.

Figure 3 .
Figure 3. Cleaning efficiency (oil-uptake) performance test made on contaminated stainless-steel tiles using the C 8-10 G m surfactant concentrations, CG1 (A), CG5 (B), and CG10 (C), and the C 8-10 G m surfactant + C 12 OH CG1C (D), CG5C (E), and CG10C (F).Finally, weight loss of contaminants from stainless-steel tiles (previously contaminated with HVS soil and oils) after 18 h of immersion in the respective solutions (G).The weight loss can be observed qualitatively as the amount of oil uptake.

Figure 4 . 1 H
Figure 4. 1 H NMR spectra of the 1 v/v% C 8-10 G m , CG1-Dirty, and the 1 v/v% C 8-10 G m + 0.25 v/v% C 12 OH, CG1C-Dirty, after the cleaning procedure, i.e., containing contaminants (A).Exponential echo decays of the surfactant resonance region (B).The red (solid and dotted) lines represent singleexponential decay (Equation (3)), while the blue line represents double-exponential decay.The surfactant self-diffusion coefficients extracted from the echo decays using the Stejskal and Tanner equation (Equation (3)) and the double-exponential decay of the CG1C-dirty samples lead to the two self-diffusion coefficients, D1 and D2 (C).

Figure 5 .
Figure 5.A known amount of petroleum ether was added to both the 1 v/v% C8-10Gm sample, CG1 (A-D), and the 1 v/v% C8-10Gm + 0.25 v/v% C12OH sample, CG1C (E-I).The ratio is expressed as a volume ratio, where the first number denotes the sample volume, and the second number represents the volume of petroleum ether.For the 2:0.3 ratio of sample CG1, panel H displays the sample after 24 h of stabilization, while panel I shows it after 96 h.

Figure 5 .
Figure 5.A known amount of petroleum ether was added to both the 1 v/v% C 8-10 G m sample, CG1 (A-D), and the 1 v/v% C 8-10 G m + 0.25 v/v% C 12 OH sample, CG1C (E-I).The ratio is expressed as a volume ratio, where the first number denotes the sample volume, and the second number represents the volume of petroleum ether.For the 2:0.3 ratio of sample CG1, panel H displays the sample after 24 h of stabilization, while panel I shows it after 96 h.
Figure S1: Correlation function (B) and volumeweighted distribution (A) of C 8-10 Pm and C 8-10 Pm + C 12 OH.Figure S2: Cleaning tests of stainlesssteel plates for CG1P (A), CG5P (B), and CG10P (C) samples and cleaning efficiency indicated by weight loss or oil uptake (D).Table S1: Samples under investigation for Figure S2.