Achieving a Toothed Gear on Presses †

: This paper presents a device that, in ﬁnal connection with presses, allows toothed gear (with a crown similar to a toothed wheel with right teeth) to be achieved by hot deformation starting from a cylindrical steel bar. For this, ﬁnite element simulations were performed in Forge software. The proposed device has 23 rollers, so for the simulation process, a slice representing a part (the 23rd) of a circle which simpliﬁes the essential functionality of this device was taken into consideration.


Introduction
From the start of this research problem, it should be noted that the semi-finished product was obtained through a plastic forming process (pressing) by an equipment with 23 forming rollers [1]. The symmetry axis of the set is collinear to the symmetry axis of the final toothed gear, so we subjected a slice which is the 46th part from 360 • , namely 7.8 • , in the simulations. Additionally, we tried to quantify the implications of operating the press punch on the designed and assembled toothed gear wheel.
A mesh network was built for each slice, and the corresponding plastic deformation equations were applied in each of them. Through this research methodology, we noticed how each simulated slice of 7.8 • was affected overall, so we reached the necessary conclusions that led us to make the necessary changes in the whole assembly, and finally we saw how the whole set behaved.
The technical parameters of this plastic deformation process were deduced. It was proven that the technical feasibility for the manufacture of toothed gear wheels through this method is clearly superior to the classical method which involves milling, especially due to the significantly higher productivity of the proposed process and the material saving, in addition to the advantage of toothed gear wheels obtained with continuous fiber, who are much more resistant from a mechanical point of view.

The Pressing
We started from the idea of making a toothed gear by pressing a cylindrical semi-finished product, made by drawing [2,3], through a roller device. In a specific case, we decided that the device should consist of 23 deformation rollers and a body (fixed) on which these rollers are assembled. The design was created using a CAD software: SolidWorks (see Figure 1). It must be noted that the device was made only for research, being intended for the realization of a gear with straight teeth having a certain number of teeth (23) and a certain circular pitch, respectively. design was created using a CAD software: SolidWorks (see Figure 1). It must be noted that the device was made only for research, being intended for the realization of a gear with straight teeth having a certain number of teeth (23) and a certain circular pitch, respectively. For practical, concrete cases, such a device can be built for each desired value of the number of teeth and the circular pitch "p" of the final toothed gear. The toothed gear achieved device, built, has 23 deforming rollers, for simulation using the 46th part of a virtual circle, which has in the center the longitudinal axis of symmetry of the semi-finished product, thus being similar to a slice with peak angle of 7.8° as is shown in Figure 2. This simplification was used to speed up the analysis time of the simulation process. We want to mention that the simulation of the deformation process was simplified to a "slice" because the process is axisymmetric.

The Device Description
The previously proposed device was actually made to confirm the simulation results and its design and real assembly is shown in Figure 3.  For practical, concrete cases, such a device can be built for each desired value of the number of teeth and the circular pitch "p" of the final toothed gear.
The toothed gear achieved device, built, has 23 deforming rollers, for simulation using the 46th part of a virtual circle, which has in the center the longitudinal axis of symmetry of the semi-finished product, thus being similar to a slice with peak angle of 7.8 • as is shown in Figure 2.
Proceedings 2020, 63, 57 2 of 8 design was created using a CAD software: SolidWorks (see Figure 1). It must be noted that the device was made only for research, being intended for the realization of a gear with straight teeth having a certain number of teeth (23) and a certain circular pitch, respectively. For practical, concrete cases, such a device can be built for each desired value of the number of teeth and the circular pitch "p" of the final toothed gear. The toothed gear achieved device, built, has 23 deforming rollers, for simulation using the 46th part of a virtual circle, which has in the center the longitudinal axis of symmetry of the semi-finished product, thus being similar to a slice with peak angle of 7.8° as is shown in Figure 2. This simplification was used to speed up the analysis time of the simulation process. We want to mention that the simulation of the deformation process was simplified to a "slice" because the process is axisymmetric.

The Device Description
The previously proposed device was actually made to confirm the simulation results and its design and real assembly is shown in Figure 3.  This simplification was used to speed up the analysis time of the simulation process. We want to mention that the simulation of the deformation process was simplified to a "slice" because the process is axisymmetric.

The Device Description
The previously proposed device was actually made to confirm the simulation results and its design and real assembly is shown in Figure 3.
Proceedings 2020, 63, 57 2 of 8 design was created using a CAD software: SolidWorks (see Figure 1). It must be noted that the device was made only for research, being intended for the realization of a gear with straight teeth having a certain number of teeth (23) and a certain circular pitch, respectively. For practical, concrete cases, such a device can be built for each desired value of the number of teeth and the circular pitch "p" of the final toothed gear. The toothed gear achieved device, built, has 23 deforming rollers, for simulation using the 46th part of a virtual circle, which has in the center the longitudinal axis of symmetry of the semi-finished product, thus being similar to a slice with peak angle of 7.8° as is shown in Figure 2. This simplification was used to speed up the analysis time of the simulation process. We want to mention that the simulation of the deformation process was simplified to a "slice" because the process is axisymmetric.

The Device Description
The previously proposed device was actually made to confirm the simulation results and its design and real assembly is shown in Figure 3.   Starting from a cylindrical semi-finished product (see Figure 4a), the device manages to make toothed gears by hot forming, similar to that shown in Figure 4b.
Proceedings 2020, 63, 57 3 of 8 Starting from a cylindrical semi-finished product (see Figure 4a), the device manages to make toothed gears by hot forming, similar to that shown in Figure 4b.

Simulation
The simulations were performed by finite element analysis (FEA), using FORGE software.

The Dimension Assessment of the Initial Semi-Finished Product
Basically, the diameter Ds of the semi-finished product and its height Hs were determined. The mathematical calculation of the diameter Ds of the semi-finished product implies that the sum of the transverse areas of the portions displaced by the action of the forming rollers must be equal to the sum of the transverse areas of the tooth tips formed by the flow of the material [4] (see Figure 6).  In fact, the intermediate technical stages (viewed in cross section) are detailed in Figure 5. Starting from a cylindrical semi-finished product (see Figure 4a), the device manages to make toothed gears by hot forming, similar to that shown in Figure 4b.

Simulation
The simulations were performed by finite element analysis (FEA), using FORGE software.

The Dimension Assessment of the Initial Semi-Finished Product
Basically, the diameter Ds of the semi-finished product and its height Hs were determined. The mathematical calculation of the diameter Ds of the semi-finished product implies that the sum of the transverse areas of the portions displaced by the action of the forming rollers must be equal to the sum of the transverse areas of the tooth tips formed by the flow of the material [4] (see Figure 6).

Simulation
The simulations were performed by finite element analysis (FEA), using FORGE software.

The Dimension Assessment of the Initial Semi-Finished Product
Basically, the diameter D s of the semi-finished product and its height H s were determined. The mathematical calculation of the diameter D s of the semi-finished product implies that the sum of the transverse areas of the portions displaced by the action of the forming rollers must be equal to the sum of the transverse areas of the tooth tips formed by the flow of the material [4] (see Figure 6). Starting from a cylindrical semi-finished product (see Figure 4a), the device manages to make toothed gears by hot forming, similar to that shown in Figure 4b.

Simulation
The simulations were performed by finite element analysis (FEA), using FORGE software.

The Dimension Assessment of the Initial Semi-Finished Product
Basically, the diameter Ds of the semi-finished product and its height Hs were determined. The mathematical calculation of the diameter Ds of the semi-finished product implies that the sum of the transverse areas of the portions displaced by the action of the forming rollers must be equal to the sum of the transverse areas of the tooth tips formed by the flow of the material [4] (see Figure 6).

The Von Mises Stress Determination
In the second phase, with these correct dimensions, a mesh network was applied both for the semi-finished product and for the analyzed device. Thus, the final values of von Mises stress were deduced. Because both the semi-finished product and the analyzed device were involved in the simulation at this moment, a view was achieved in its longitudinal section, focused on the von Mises stress that appeared at the deformation of the semi-finished product [6]. Figure 9 shows 5 figures made at various deformation moments: (a) corresponds to the deformation start time t = 0 (initial

The Von Mises Stress Determination
In the second phase, with these correct dimensions, a mesh network was applied both for the semi-finished product and for the analyzed device. Thus, the final values of von Mises stress were deduced. Because both the semi-finished product and the analyzed device were involved in the simulation at this moment, a view was achieved in its longitudinal section, focused on the von Mises stress that appeared at the deformation of the semi-finished product [6]. Figure 9 shows 5 figures made at various deformation moments: (a) corresponds to the deformation start time t = 0 (initial deformation moment), (b) corresponds to the moment t/5, (c) moment (2/5)·t, (d) moment (3/5)

The Semi-Finished Product Deformations
This simulation is similar as aspect to the previous one, practically focusing on the amplitude of the deformations of the semi-finished product along the entire time interval (t) of its deformation, as shown in Figure 10.

The Flow of the Semi-Finished Material
Mesh network was no longer viewed. The whole system device-part was cut from the entire longitudinal section with the aim of analyzing only the evolution of the flow of the part material, as shown in Figure 11.

The Semi-Finished Product Deformations
This simulation is similar as aspect to the previous one, practically focusing on the amplitude of the deformations of the semi-finished product along the entire time interval (t) of its deformation, as shown in Figure 10.

The Semi-Finished Product Deformations
This simulation is similar as aspect to the previous one, practically focusing on the amplitude of the deformations of the semi-finished product along the entire time interval (t) of its deformation, as shown in Figure 10.

The Flow of the Semi-Finished Material
Mesh network was no longer viewed. The whole system device-part was cut from the entire longitudinal section with the aim of analyzing only the evolution of the flow of the part material, as shown in Figure 11.

The Flow of the Semi-Finished Material
Mesh network was no longer viewed. The whole system device-part was cut from the entire longitudinal section with the aim of analyzing only the evolution of the flow of the part material, as shown in Figure 11.

The Flow of the Semi-Finished Material
Mesh network was no longer viewed. The whole system device-part was cut from the entire longitudinal section with the aim of analyzing only the evolution of the flow of the part material, as shown in Figure 11. Figure 11. The flow of the semi-finished material, in the process of its plastic deformation. Figure 11. The flow of the semi-finished material, in the process of its plastic deformation.

Conclusions
In this research, it was proven that toothed gears with a certain circular pitch and number of teeth can be achieved by this method [7] of plastic deformation, and as with any process of plastic deformation, the fibrous structure being continuous, it results in a more resistant final product, able to respond more efficiently to various mechanical stresses [8]. During the practical hours of simulation, it was also observed that the flow of the material in the tooth formation imposes a certain regime of deformation speed. It was also observed that in the case of obtaining steel toothed gears, the respective deformation process will be performed hot, requiring only the heating of the cylindrical surface of the initial semi-finished product.