Irreversibility of the Direct and Counter Impinging Liquid Jet onto Profiled Heated Cavity

Liquid impinging jet at the bottom of the annular cavity is a typical case in the process industry. The jet could have an impact at the bottom center or its peripheral section. The profiled annular cylindrical cavity with the installed electricity heater source is investigated in this paper. Thermal contact irreversibility and liquid drag irreversibility are generated within the profiled cavity. Through analytical modeling and experimental verification, a valid model of the entropy generation is established for both states. The results show that the total entropy between the liquid and the bottom is many times greater for the case of the central jet impingement. Within the annular vertical walls are the locations of the maximum or minimum of the entropy. The effectiveness of the liquid heating is greater in the peripheral impact of the liquid. The method and the results are the basis for optimizing the profiled cavity in various optimization geometry parameters. The optimal geometry of the annular cavity exists in such a way that the balance between thermal irreversibility and liquid drag irreversibility leads to the total minimum rate of the entropy generation for the annular cavity.


Introduction
Fluid jet impact on curved surfaces and semi-enclosed cavities often happens in thermo-fluid technologies. Many researchers have studied impinging liquid jets on horizontal flat surfaces for established heat transfer. Thus, L. Huang and M. S. El-Genk [1] analyzed and experimentally investigated the heat transfer between heated plate and an impinging circular air jet in order to determine the values of the Nusselt numbers, for small values of the Reynolds number. A.K. Mohanty and A.A. Tawfek [2] measurements the heat transfer from an isothermal plate due to an impinging air jet for different diameters of circular nozzles and Reynolds number. A. H. Beitelmal et al. [3] experimentally studied the effect of the inclination of an impinging air jet on the heat transfer from a heated plate. The experimental investigation of the fluid flow and heat transfer of the rectangular air jet impinging on a heated plate investigated by D.W. Zhou and S. J. Lee [4]. M. Behnia, S. Parneix and P.A. Durbin [5] numerically studied cooling of the heated plate by axisymmetric isothermal turbulent jet. A. V. Nguyen and G. M. Evans [6] studied gas jets impinging onto a gas-liquid interference of a liquid pool using fluid dynamics modeling. D. M. Esparza et al. [7] numerical studied impinging jets over liquid surfaces common in the metallurgy and chemical industry. With regard to analysis and studies show of entropy generation induced by hydraulic and thermal irreversibility A. Bejan [8] gives many different examples generated entropy of different thermal fluid interactions. The minimize the entropy generation of the heat transfer from a thicker plate to a laminar impinging planar jet investigated by G. Ruocco [9]. S. Chen and C. Zheng [10] investigated entropy generation in impinging flow on planar opposing jets. S.Z. Shuja et al. [11] numerically computed local entropy generation rate for the fluid impinging fluid jet on a heated wall. Also, some researchers conducted the analysis and study of entropy generation within the annular channel. O.M. Haddad et al. [12] numerically studied entropy production due to forced convection within the concentric cylindrical annulus. M. Torabi and K. Zhang [13] investigated local and total entropy generation within a composite hollow cylinder with thermal conductivity and heat source. This paper also observed and analyzed entropy generation paradox, i.e. that minimize of the entropy generated does not mean at the same time maximizing the coefficient of performance (COP) of the system. This paradox observed by several researchers, one of them is A. Bejan [14] which is entropy generation paradox observed with counter flow heat exchanger. Also, Shah and Skiepko [15] analyzed 18 types of heat exchangers and came to the conclusion that achieving the maximum coefficient of efficiency does not mean that at the same time established a minimum entropy of the heat exchanger. Similar conclusions come other authors Y. Guo et al. [16], and X. D. Qian and Z. X. Li [17].
This paper presents a comparative analysis of the thermal and hydraulic irreversibility of central and peripheral impinging liquid jets on the heated bottom of a profiled cylindrical cavity. A central liquid impinging on the bottom of a cavity includes both the impact liquid at the center bottom of the profiled cavity and its exit through the peripheral part of the cylindrical cavity. The peripheral impact of liquid on the bottom includes the counter impinging liquid jet in the peripheral part of the bottom and a liquid outlet in the central part of the cavity in the direction of the axis perpendicular to the bottom of the cylindrical cavity. Accordingly, the inlet and outlet of the liquid are such that the two impinging jets are reversed. The overall cylindrical cavity was heated with a heating source of constant temperature located at the bottom. The temperature at the bottom of the cavity was kept constant, while the temperature of the wall of the cylindrical cavity was heated from the bottom. The temperature of the wall cavity is a function of the wall height and the convective heat transfer coefficient between the cylindrical cavity's inner wall surface and the liquid. The cylindrical cavity was thermally insulated from the outside surface, which was in contact with the surroundings. Also, the inner central channel was thermally insulated from the cylindrical peripheral annular channel. As previously stated, the goal of this research was to identify the difference of thermal and hydraulic irreversibility entropy in such a heating system. The total generated entropy consists of the thermal entropy caused by heat transfer between the cylindrical cavity and the liquid, while the hydraulic entropy results from the friction loss of liquid flow through the cavity. In this analysis, the variables were temperature at the bottom, the liquid flow, the distance from the center of the bottom, and the height of the cylindrical annular channel. This research involved a comparative analysis of thermal and hydraulic irreversibility of the central and peripheral impinging liquid jets on the heated bottom of a cavity. Besides the total entropy, for different conditions, dimensionless sizes as Bejan numbers and irreversibility distribution ratios were compared. This research involved analyzing the entropy generation paradox, i.e., that minimizing entropy generated does not mean maximizing a system's coefficient of performance (COP).

Materials and Methods. The Reasons for this Research. Thermal and Hydraulic Irreversibility
Liquid jet impingement on the bottom of an annular cavity is a common occurrence in the process industry. There are many technical applications in which liquid or some other fluid impinges on a heated wall. Often in thermal and fluid techniques where a liquid impinges on a semi-closed heating cavity and then exits out of the same cavity. This is the case in various vessels with heated bottoms, such as closed profiled pipes, various semi-open channels, etc. Except for the central jet impact, there are situations of liquid counter-impinging on a heated surface. The central and peripheral impacts of liquid on a heated surface may appear within the same semi-closed cavity, which occurs by changing the direction of liquid flow. However, the heat exchange between the liquid and heated cavity causes thermal irreversibility. The flowing liquid, according to friction forces and local hydraulic resistance, generates hydraulic irreversibility. The total generated entropy of the interaction between the cavity and the liquid is equal to the sum of the thermal and hydraulic entropies. Accordingly, there is a need for entropy analysis of the described impact liquid; thus, this research investigated the profiled cavity with a heating source installed on the bottom. Both of the above cases were analyzed under the same conditions and using the same methodology. The aim of this research was to determine the differences in values of generated entropy caused by thermal and hydraulic irreversibility. An additional goal of this research was to establish a mathematical model for dependence-generated entropy of the characteristic geometric parameters of heating cavities. This resulting mathematical model can be a good basis for optimizing the geometric parameters of such cylindrical cavities, such as, for example, minimizing total entropy generated, which could reduce unnecessary thermal and hydraulic losses.

Central Impinging Liquid Jet on the Bottom of the Cylindrical Cavity
and obtained, (Equation (5)) after separation of the variables and integration where c λ the conductivity of the material cavity, c δ the thickness of the vertical wall of the cavity, 2 α convection coefficient between the vertical cylindrical wall and ) (h T l liquid temperature.
Finding the temperature of the liquid within the annular channel, Figure 2, is obtained after the establishment of heat balance and after separation of the variables, by integration and combining with Equation (7) obtained the temperature of the liquid within the annular channel of the heating cavity  , i.e., the liquid and the annular vertical part of the cavity , is represented by Equations (9) and (10), respectively.
In Equation (9), The irreversibility distribution ratio φ , as ratio hydraulic and thermal irreversibility, gives the possibility to evaluate the influence of losses and their relevance in the process of heat exchange. This ratio φ according to Equations (9) and (10) can be represented by the following Equations, (11) and (12).
The irreversibility distribution ratio o φ refers to the thermo-hydraulic interaction of the bottom and liquid, while the irreversibility distribution ratio 1 φ refers to the annular channel of the cylindrical cavity.

The Peripheral Impinging Liquid Jet on the Bottom of the Cylindrical Cavity
As in the previous case, the bottom of the cavity was heated with an electric heater at constant temperature co T . In this case, a liquid of temperature in l T . and velocity 1 w passed through the annular vertical channel, impacted the peripheral part, and exited through the central cylindrical channel at height o h , as shown in Figure 3.

Results. The Central Impinging Liquid Jet
The Geometrical Change Figure 5 shows the total generated entropy induced by the thermal irreversibility


. The maximum thermal entropy occured 0.06 m from the bottom, after which the values of entropy decreased. Both diagrams of Figure 5 show that, as expected, the generated entropy values were greater for the higher temperature of 100 °C. Figure 6 shows the total generated entropy induced by the hydraulic irreversibility


, the temperature influence at the bottom is clearly visible in both diagrams of Figure   6. The lower temperature of 60 °C at the bottom of the cylindrical cavity reduced the generated entropy caused by hydraulic irreversibility. The dimensionless characteristic ratio for describing the impact of hydraulic generated entropy  often uses the irreversibility distribution ratio φ defined by Equations (11) and (12). In accordance with the left and the right diagrams of Figure 7, it is clear that small value dimensionless ratios φ directly indicate that the hydraulic generated entropy  In accordance with Figure 3, and in the context of Figure 7 with an increase in the thermal entropy T gen S Δ .


directly decrease values of dimensionless ratio φ .
For example, in the annular channel, the maximum value of the thermal entropy is at a vertical distance of 0.06 m, as shown in Figure 5, while, at that same distance the irreversibility distribution ratio φ is at the minimum value. One of the commonly used dimensionless ratios is the Bejan number Be , presented by Equations (13) and (14), which represents the ratio of the generated entropy caused by thermal irreversibility

 
caused by thermal and hydraulic irreversibility. As can be seen by comparing Equations (11) and (12) with Equations (13) and (14) and the diagrams in Figures 7 and 8, the irreversibility ratio φ and Bejan number Be are in inverse proportion when the hydraulic irreversibility is negligible compared to the thermal irreversibility, as was the case in this analysis. The values of Bejan number Be are between 0 and 1; in when heat exchange is far greater than hydraulic loss, the value of this number is about 1. Without heat exchange, the value of this number is zero.

The Geometrical Change
In the case of the peripheral impinging jet, shown in Figures 3 and 4, the inlet temperature of the liquid was


, as sshown in the left diagram of Figure 9.     Figure 12 shows that the irreversibility distribution ratio φ of the annular channel was greatest 0.044 m from the bottom. This distance was the same for both temperatures of 60 °C and 100 °C.  Figure 9. In contrast to the irreversibility distribution ratio, the Bejan number has an inverse function, as shown in Figure 13. Figure 9 shows that the minimum Bejan number, with only minor changes from hydraulic entropy  As previously noted, the values of entropy, irreversibility distribution ratio, and Bejan number shown in Figures 5 to 13 represent the individual effects of the vertical annular channel and the bottom of the cavity on the liquid jet, i.e., its flow through the described profiled cylindrical cavity.


. However, the temperature of the vertical annular wall was not constant at a height h .


, which affects the increase of the irreversibility distribution ratio φ . For the lower bottom temperature of 60 °C, thermal entropy was lower an hydraulic entropy was greater, which caused a greater irreversibility distribution ratio. The higher bottom temperature of 100 °C caused more heat exchange between the cylindrical cavity and the liquid, i.e., led to a higher Bejan number. However, increasing the inlet liquid velocity value decreased the Bejan number, as shown in Figure 15. The reason for this decrease of the Bejan number with increasing inlet liquid velocity w is the increase in hydraulic entropy casued by the increased inlet liquid velocity and the total generated entropy  Diagrams of the effectiveness of the direct and counter impinging liquid on the heating bottom were established in accordance with Equation (15). Higher values of effectiveness happened with direct liquid impinging on the heated bottom. Higher velocities of liquid intensified the heat exchange, thus causing the vertical part of the annular cavity to cool faster, leading to lower values for effectiveness, as shown in Figure 16.

Entropy Generation Paradox and Entropy Maximum
The minimum generated entropy of a system does not always mean that the maximum coefficient of performance (COP) is evident in a thermo-technique system; this is called the entropy generation paradox. This paradox suggests that decreasing the generated entropy of a system does not mean at the same time increasing the coefficient of performance (COP). As already presented, this research analyzed direct and indirect impinging liquid jets on the heated bottom of a cylindrical cavity and the effects on generated entropy and effectiveness. Figure 17 presents the generated entropy and the coefficient of performance COP as a function of the height of the cylindrical cavity at different values for the Reynolds number for both the direct, shown on the the left, and counter impinging, shown on the right, liquid jets on the heated bottom of the cylindrical cavity. In the first case, it can be seen that the noticeable interval for the paradox of entropy generation was for heights of the cylindrical vessel above 0.066 m at the Reynolds number of 15,000. Reducing the Reynolds number decreased the interval of the entropy generation paradox. In the counter impinging liquid jet, Figure 17 right, the entropy generation paradox was noticeable for all heights of the cylindrical cavity. Figure 18 shows that maximum generated entropy decreased with increasing height of the cavity ho.

The Contribution of This Work
This research demonstrates that a central impinging liquid jet onto a heated profiled cavity generates higher thermal and hydraulic entropies, i.e., total irreversibility. The directly impinging liquid had greater entropy, while the coefficient of performance was higher with direct impinging compared to peripheral impacting. This resulted in the entropy generation paradox, as mentioned in the previous section.

The Limitations of This Work
-It did not account for heat exchange between the cylindrical cavity and the environment because it was thermally insulated from the outside. -It is did not account for heat exchange between the central and peripheral liquid jets.

-
The liquid velocity within the channels of the cavity was considered at an average value.

Benefits of This Work
This research contributes in the following ways: -Establishes a mathematical model for the thermal and hydraulic irreversibility of direct and counter impinging liquid jets onto a heated cylindrical cavity. This mathematical model can be a basis for minimizing total generated entropy.

-
Presents the advantages and disadvantages of direct impinging liquid jets compared to indirect liquid impacting. There is the possibility to choose parameters for liquids or cavities in various industrial applications, both for cooling and heating a cavity with a liquid.

-
Establishes the most unfavorable heights, in terms of maximum entropy, of a cavity for a direct impinging liquid jet as a function of different values of the Reynolds number.

Validation Results
The mathematical model was validated with experimental testing of the central and peripheral impinging liquid jets in a profiled cavity at the same boundary conditions, as well as in mathematical analysis. The generated entropy caused by the thermal irreversibility   Also, effectiveness was experimentally determined in accordance with the left side of Equation (15). Figure 21 shows comparative diagrams for direct and peripheral impinging on the heated bottom. By comparing the experimental results with the results of mathematical modeling, it can be concluded that the used mathematical model satisfactorily describes the irreversibility of thermal hydraulic system, as analyzed in this paper.

Conclusions
This paper presents the investigation and analsysis of entropy for two cases of liquid impinging jets within a profiled cylindrical cavity. In the first case, the liquid jet impacted the center of the bottom and exited through the peripheral annular channel, while the second case involved a liquid impinging jet. Both of the above cases involved mathematical modeling of thermal and hydraulic entropy, irreversibility distribution ratio, and the Bejan number as a function of the radius of the bottom of the cavity and the height of the peripheral annular channel. Also, this research investiagted the effects of varying liquid input velocities, with constant geometric dimensions of the cylindrical cavity, on thermal and hydraulic irreversibility. The research conclusions are as follows:

-
The total generated entropy for a central impinging liquid jet of constant inlet velocity is lower than for a counter impinging liquid jet on the peripheral part of the bottom of the cylindrical cavity. on the bottom by many times greater than its on the vertical annular channel. However, the total thermal entropy of the cylindrical cavity is many times greater than the total hydraulic generated entropy. Either the minimum or maximum thermal entropy appears within the annular channel. This depends on whether the liquid flow enters or exits through the annular channel, or whether the liquid centrally or peripherally impinges on the bottom of the cavity.

-
The research has also shown that the effectiveness of the heating profiled cavity is greater in the case of a direct impinging liquid jet on the bottom of the cavity.

-
The above can be applied and in the case of a profiled cylindrical cavity cooled with liquid.

Future Research Directions
A mathematical model of entropy generation caused by thermal and hydraulic irreversibility was developed based on the analyses and tests in this study. This mathematical model can provide a good basis for optimizing this system. For example, it can be used for minimizing thermal and hydraulic irreversibility.