Laser Scanners for High-Quality 3D and IR Imaging in Cultural Heritage Monitoring and Documentation

: Digital tools as 3D (three-dimensional) modelling and imaging techniques are having an increasing role in many applicative ﬁelds, thanks to some signiﬁcative features, such as their powerful communicative capacity, versatility of the results and non-invasiveness. These properties are very important in cultural heritage


Introduction
Artistic and cultural heritage (CH) is essential for present and future generations as a proof of human genius over the past eras, and its preservation has a key role in transmitting cultural and historical roots of nations around the world [1][2][3]. The safeguard and the communication of global CH are therefore more than an exclusively humanistic issue, being involved in many scientific activities of national and international institutions. The numerous variables involved in CH Conservation Science, such as the conservation status, material composition and the surrounding conditions, require the development of specific and multidisciplinary applicative solutions, both in terms of instrumentation and methodology [4]. In the actual digital era, imaging techniques and 3D (three-dimensional) modelling are widely employed in CH for recording and remote investigations, becoming common practice used in archaeological sites for contactless surveys [2,[5][6][7]. The digital information achieved with these methodologies has an important usefulness, not only for historical reconstructions and dissemination purposes, but also for monitoring and diagnostic studies, allowing for investigations and comparisons of conservation status over time. Many methods are nowadays available for gaining these purposes and differ for factors, such as acquisition timing, resolution, accuracy and typology of achievable results [5,6,[8][9][10][11][12]. Despite the variety of systems, functionalities and properties, it is well-known that one single method is insufficient for the complete 3D color digitalization of a

ITR Technology and Systems
The DIM laboratory (Diagnostics and Metrology) of the ENEA Research Center has been working on laser applications for over two decades, developing several prototypes for many fields, from forensic science to CH studies [29,30]. In this paper, we present two laser scanners based on the use of n-laser stimuli as light sources for contactless acquisition of backscattered information: the RGB-ITR (Red Green Blue-Imaging Topological Radar) and the IR-ITR (Infrared-Imaging Topological Radar). The ITR systems are based on the double amplitude modulation (AM) range-finding technique, where the laser beam is exploited as the carrier wave of a radiofrequency signal, which modulates the beam intensity [31,32]. The double modulation of the laser sources combined with the lock-in technique allows estimating the amplitude and phase-shift information of the back-reflected signals from the target simultaneously. The estimation of the amplitudes' information, proportional to the matter/laser interaction at a specific optical wavelength, contributes to the color (RGB-ITR version) or grey-level intensity (IR-ITR version) reconstruction of the target, while the phase-shift information to estimate the distance occurred between the scanner and the investigated surface. The amplitude and phase-shift information is actually stored point-by-point, collecting electronic signals in a range between 1 × 10 −4 and 0.1 Volts. Structural digitalization of the surfaces is elaborated from the distance measurements, determined indirectly from the phase delay ∆ϕ of the collected back-reflected signal with respect to the reference modulating wave, as expressed by the formula [33]: where f m is the modulation frequency and ν is the velocity of light in the transmitting medium. For laser optical powers where the shot noise dominates over all other noise sources in the detection process (typically, a few nW at the output of the detection fiber), the accuracy of distance measurements can be shown to increase with the modulation frequency f m [33] according to the following expression: where σ R is the "intrinsic" error (i.e., the minimum attainable error in optimal experimental conditions), m is the modulation depth and SNR i is the current signal-to-noise ratio: which depends on the laser optical frequency f , the integration time τ, the detector's quantum efficiency η, the overall optics merit factor Γ and the collected power P. Here, h stands for the Planck constant. Efficient noise rejection is obtained by using narrow field-of-view, interferential filtering and low-noise detection electronics. Because of phase periodicity, the AM technique is affected by the so-called "folding" ambiguity: the system returns the same distance value for target points, of which relative separation along the line of sight is a multiple of half the modulation wavelength. In order to overcome this problem, the laser probe is modulated at two different frequencies with values taken far apart from each other. The lower modulation frequency is calculated by the corresponding measurement range encompassing the whole scene of interest. Low-frequency measurements are then used to remove the ambiguity that affects the corresponding high-frequency, employed for more accurate measures. By using this technique of double AM, it is possible to achieve sub-millimetric accuracy on targets at distances or heights from a few tenths up to 30-35 m, without the need of scaffolding [28,31]. The ITR hardware is composed of two physically separate modules but optically connected by means of optical fibers: the optical head and the electronic components. In particular, the scanning module, i.e., the optical head, of the two instruments basically includes the launching and receiving optics, and it consists of a lens system for the collimation and focalization of the lasers to the center of a double-motorized mirror. The latter sweeps the beam onto the target according to a TV raster-like positioning, differently from the rotative movement of commercial scanners, and collects the back-reflected beam. The returning signals are detected by low-noise photodiode detectors and analyzed by means of lock-in amplifier units, which are also used to modulate the laser sources. The data are processed with custom software through MATLAB ® interface (see Section 2.3), and the resulting models and images can be exported into the most common file formats, thanks to the feature of the software. Figure 1 shows a schematic explanation of the ITR system operability. The parameters of the ITR scanners for defining their accuracy and resolution are: the laser spot size, which determines the minimum area of the collected pixel; the signal/noise ratio for estimating the distance measurement; the minimum angular step of the motorized mirror, responsible for the movement of the laser beam; the single pixel distance between the device and the target, which determines the spatial resolution between one point and the neighbors [34]. Due to construction limits of the optical heads of the systems, the actual rotation movement of the scanning mirrors is 1.4 × 5.4 rad (80 • × 310 • ), with a maximum point-to-point precision of 0.035 mrad. The pixel distance accuracy is 350 µm at 10 m of distance between system and target, while the spatial resolution is 700 µm. The average spot diameters measured at the same distance range are less than 1 mm for the RGB-ITR and 4-5 mm for the IR-ITR. The two ITR systems differ in number and wavelength of the laser sources, achieving two types of results: the RGB-ITR scanner (see Section 2.1) employs three wavelengths in the visible spectrum to obtain high-quality 3D color models of the object, while the IR-ITR instrument (see Section 2.2) uses a single infrared source for layering analyses of the surface.
J. Imaging 2018, 4, x FOR PEER REVIEW 4 of 18 Figure 1. Scheme of the ITR technology: by the use of custom software, the scanning process is remotely controlled by a laptop connected to the electronic components. The laser beam (infrared (IR) or in the visible range-RGB) is generated by laser sources, modulated and amplified by lock-in techniques. Through optical fibers, the lasers are carried inside the optical head, where a system of lenses collimates and focalizes the ray on the center of a movable scanning mirror, which drives the incident laser beam on the surface's object and collects the backscattered beam, elaborated with custom software.

RGB-ITR Scanner
The RGB-ITR scanner ( Figure 2) enables the simultaneous recording of range and color information by the phase-shift between the back-reflected signal and the reference modulating wave, and the elaboration of back-reflected RGB triplets from the scanned object, respectively. At the moment, the system uses three laser sources with wavelengths in the visible range corresponding to red, green and blue (660 nm, 517 nm and 440 nm), respectively [31]. Through optical fibers, the lasers are carried inside the optical head, where a system of lenses collimates and focalizes the ray on the center of a movable scanning mirror, which drives the incident laser beam on the surface's object and collects the backscattered beam, elaborated with custom software.

RGB-ITR Scanner
The RGB-ITR scanner ( Figure 2) enables the simultaneous recording of range and color information by the phase-shift between the back-reflected signal and the reference modulating wave, and the elaboration of back-reflected RGB triplets from the scanned object, respectively. At the moment, the system uses three laser sources with wavelengths in the visible range corresponding to red, green and blue (660 nm, 517 nm and 440 nm), respectively [31]. Through optical fibers, the lasers are carried inside the optical head, where a system of lenses collimates and focalizes the ray on the center of a movable scanning mirror, which drives the incident laser beam on the surface's object and collects the backscattered beam, elaborated with custom software.

RGB-ITR Scanner
The RGB-ITR scanner ( Figure 2) enables the simultaneous recording of range and color information by the phase-shift between the back-reflected signal and the reference modulating wave, and the elaboration of back-reflected RGB triplets from the scanned object, respectively. At the moment, the system uses three laser sources with wavelengths in the visible range corresponding to red, green and blue (660 nm, 517 nm and 440 nm), respectively [31].  Firstly, the three laser beams are overlapped by dichroic filters in a single white incident ray with a laser spot diameter of 1-2 mm at distances greater than 10 m and an overall power are calculated by the following formula: Power density mW mm 2 = Laser power /Spot area = 3 mW /0.785 mm 2 = 3.821 mW /mm 2 , where 3 mW correspond to the laser power of the three wavelengths in the visible range and the spot area is referred to a 1 mm-dimeter laser spot. A 40 mm-focus achromatic lens focuses the launching beam onto the target by means of a rotating mirror, while a 150 mm-focus lens is used for collecting and focusing the backscattered beams, split again into the three original red, green and blue components by means of an optical demultiplexer. The signals, in the ranges for each channel of about 0.1-100 mV, are detected by three low-noise avalanche photodiode detectors and analyzed by means of three lock-in amplifier units, which are also used to modulate the laser sources. Although all the beams are modulated, only the red and blue backscattered signals are exploited for high-frequency and low-frequency range determination, respectively. Typical modulation frequencies are 190-200 MHz for red, 1-10 MHz for blue and 3 MHz for green. The color information reconstruction is actually obtained by the use of just three narrow wavelengths, mainly due to the optical setup limit of the actual RGB-ITR scanner. For an accurate color estimation, an ad-hoc calibration procedure and several algorithms were implemented: as seen above, the amplitude information is stored in Volts, while the color spaces are usually described by non-dimensional normalized triplet of coordinates, like in the case of RGB, L*a*b* and HSV spaces. Moreover, all the optical signals collected by the scanner depend not only on the nature of the surface matter, but also by the quadratic dependency of the distance: to compensate these effects and normalize the data stored by the scanner, a calibration procedure is introduced. This calibration procedure consists of illuminating a certified white target by the three optical wavelengths, conveniently placed on a tripod and moved long all the linear range covered by the scanner for digitalizing the surface: every single calibration step is composed by moving the tripod every 0.5 m and collecting the back-reflected signals of the three wavelengths from the reference target. At the end of the procedure, the three distinct calibration curves (amplitude vs. distance) are used for normalizing the data collected on the investigated surface: the normalization coefficients are calculated by using, as a lookup-table, the three calibration curves interpolated by three distinct spline curves. The normalized amplitude values are calculated by dividing the single amplitude value for its equivalent normalization coefficient, also expressed in Volts, following Equation (5): The color information is also affected by the angular effect between the incident laser beams and every single illuminated portion of the surface: to balance this effect, the normalized color information is weighted by the equivalent cosine of the angles between the incident laser beam and surface normal versors (Lambert's Law), following Equation (6) [35,36]: Finally, the single point RGB triplet is obtained by using Equation (7): where S(λ i ) is a CIE illuminant, at the moment, set as energy equivalent and weighted by experimental values, R(λ i ) is the normalized reflectance factor, y cm f (λ i ) is one of the three CIE standard observer color-matching functions (x cm f (λ i ), y cm f (λ i ), z(λ i )), Σ λ represents summation across wavelength λ, ∆λ is the measurement wavelength interval, and K is a conventional normalizing constant defined as [35,37]: Finally, the calibrated RGB data is merged with range information converted into Cartesian coordinates expressed in physical units and the geometrical information is rearranged. The post-processing elaboration is carried out through the ITR software in order to produce high-quality 3D digital models of the scanned surface [34].

IR-ITR Prototype
The ITR monochromatic laser scanner ( Figure 3a) is employed for inspections under a superficial layer with a thickness of up to some hundreds of microns by the processing of backscattered data. This system uses an IR source with a wavelength of 1550 nm and a power of some tenths of mW/mm 2 . The optical setup of this system consists of an aspherical lens for focusing the launching laser beam and a receiving doublet lens (50 mm in diameter, and 150 mm in focal length) for the detection of receiving signals from up to 10 m of distance, with a laser spot size of 4-5 mm and a power density of less than 1 mW/mm 2 , as can be calculated by Equation (9): Power density mW mm 2 = Laser power /Spot area = 10 mW /12.56 mm 2 = 0.796 mW /mm 2 (9) Finally, the calibrated RGB data is merged with range information converted into Cartesian coordinates expressed in physical units and the geometrical information is rearranged. The postprocessing elaboration is carried out through the ITR software in order to produce high-quality 3D digital models of the scanned surface [34].

IR-ITR Prototype
The ITR monochromatic laser scanner ( Figure 3a) is employed for inspections under a superficial layer with a thickness of up to some hundreds of microns by the processing of backscattered data. This system uses an IR source with a wavelength of 1550 nm and a power of some tenths of mW/mm 2 . The optical setup of this system consists of an aspherical lens for focusing the launching laser beam and a receiving doublet lens (50 mm in diameter, and 150 mm in focal length) for the detection of receiving signals from up to 10 m of distance, with a laser spot size of 4-5 mm and a power density of less than 1 mW/mm 2 , as can be calculated by Equation (4): The modulation frequency in this case is 3 MHz and the principle of operation is the same as that of the RGB-ITR scanner. In this case, an IR detector (Licel APD Inasga, Figure 3b) is directly connected with the optical receiving channel and the lock-in amplifier. The Licel APD (Avalanche PhotoDiode) module combines a Si APD, TE cooler, temperature controller, low-noise amplifier and XYZ positioner in a single compact module. The laser control is carried out through a laptop equipped with suitable software, while the scanning procedure is remotely commanded with ITR custom software.

Custom Software
The scanning procedure and the post-processing elaborations are controlled by the use of custom software developed in MATLAB ® framework: ScanSystem and itrAnalyzer. The features of these tools allow setting scanning parameters based on working needs and, on the other hand, to obtain high-quality images from data elaboration.

ScanSystem
The ITR data acquisition process is driven by the custom ScanSystem tool, which allows setting scanning parameters, acquire calibration data and checking the functionality of the electronic component. With a motion controller, the software enables the movement of the laser spot onto the The modulation frequency in this case is 3 MHz and the principle of operation is the same as that of the RGB-ITR scanner. In this case, an IR detector (Licel APD Inasga, Figure 3b) is directly connected with the optical receiving channel and the lock-in amplifier. The Licel APD (Avalanche PhotoDiode) module combines a Si APD, TE cooler, temperature controller, low-noise amplifier and XYZ positioner in a single compact module. The laser control is carried out through a laptop equipped with suitable software, while the scanning procedure is remotely commanded with ITR custom software.

Custom Software
The scanning procedure and the post-processing elaborations are controlled by the use of custom software developed in MATLAB ® framework: ScanSystem and itrAnalyzer. The features of these tools allow setting scanning parameters based on working needs and, on the other hand, to obtain high-quality images from data elaboration.

ScanSystem
The ITR data acquisition process is driven by the custom ScanSystem tool, which allows setting scanning parameters, acquire calibration data and checking the functionality of the electronic component. With a motion controller, the software enables the movement of the laser spot onto the surface in order to fix vertical and horizontal limits and arranges the area to be scanned. Among the parameters controlled by the software, there are acquisition velocities (vertical and horizontal), angular resolution (calculated at each scan), number of points in terms of pixels per row. Furthermore, a single scan can be divided into multiple scripts, in order to reduce the angular span for construction limits of a scanning module or logistic reasons. The same software is used to achieve calibration data, recording reflectance signals from a white target reference at each fixed step along the distance range. The file extension of a scan project is .prj (Simulink Project), elaborated with itrAnalyzer in MATLAB ® environment, while the calibration dataset is saved as Excel file (.xls).

itrAnalyzer
Data elaborations are carried out with itrAnalyzer software, which enables several operations on ITR data, imported in MATLAB ® as matrices. The main features of this specially developed tool are 2-3D buildings of models, color and profile analyses, registration of meshes and calibrations, while among the second-level functionalities, it allows for image enhancement for the study of hidden details, color correction and smoothing. This software can be considered as the link between RGB-ITR raw data and commercial software for 3D modelling and photo manipulation.

Case Studies
The Imaging Topological Radar technology has been widely employed in CH investigations during the last twenty years with several different purposes. We report significative applications carried out in the last three years both in situ and in laboratory case studies, showing the versatility of the techniques on different materials and situations.

In Situ Acquisitions
Since 3D color digitalizations were considered among the requests and necessities, the RGB-ITR scanner has been employed. We show case studies where the scanner prototype has proved to be efficient in terms of acquisition timing, quality results and good response to specific/critical conditions. In particular, the color laser scanner has been engaged in the following sites: • Saint Brizio Chapel, Orvieto Cathedral (Viterbo, Italy); • Greek Chapel, Priscilla Catacombs (Rome, Italy); • Tower room, Saint Sebastian Gate, Aurelian Walls (Rome, Italy); • Egyptian wood sarcophagus (Milan, Italy).

Saint Brizio Chapel in Orvieto Cathedral
In the right aisle of the Orvieto Cathedral, there is what is considered to be one of the jewels of the Early Renaissance: the Saint Brizio Chapel (Figure 4a). This masterpiece dates back to the 15th century and shows the excellent skills of Italian painters, in terms of both painting techniques and realization of the topic [38]. The chapel was totally painted with the frescoes by Luca Signorelli [39], considered the master and precursor of Michelangelo. The peculiarities of the site are the high illumination due to the presence of three large windows and the gold glazing of some part of the paintings, factors that produce distortions in color transposition in most of the image-based acquisition methods [40]. The work inside the chapel was aimed at the 3D color digitalization of the frescoes, which was never done before with scanner techniques and important for structure and fresco monitoring over time.
For the acquisition process, the RGB-ITR system (Figure 4b) was set up in the center of the room, moving only the optical head in different stations in such a way as to allow the laser beam to scan the entire surface. The required time for data acquisition was about 26 h, comprehending night and day periods, without interdiction to visitors.

Greek Chapel in Priscilla Catacombs
The funerary complex of Priscilla Catacombs, dating back to between the 2nd and the 5th centuries, extends for more than 8 km under Rome at several levels of depth excavated in tuff stones. Around the cemeterial galleries, there are several important iconographic testimonies of the paleo Christian age, from inscriptions and paintings to cubicula and small rooms. Among the latter, the Greek Chapel ( Figure 5) is one of the most significative representations of the Testament inside the complex. The little chapel, which takes its name from two Greek inscriptions inside it, stands out for the colored decorations and religious scenes, unique and particular for the historical period and artistic skills [41]. The hypogeum structures are critical ambient for the pictorial elements, which can be affected by biological attack, saline efflorescence, material swelling or cracking [42,43]. Due to the particular thermo-hygrometric conditions of the Priscilla catacomb environment, such as low temperature (~14 °C) and high humidity (~98%), procedures of the monitoring and documenting of the state of health were as important as urgent in order to keep alterations, detachments and the general conservation status under control. However, uncontrolled microclimatic parameters can be damaging also to electronic components, built for operation in ideal thermo-hygrometric conditions (T~15 ÷ 35 °C, RH-relative humidity~35 ÷ 75%) [44]. In this case, the solution to the hygrometric problems, i.e., condensation, was solved, covering the electronic components with a PVC (polyvinyl chloride)-protective sheet.

Greek Chapel in Priscilla Catacombs
The funerary complex of Priscilla Catacombs, dating back to between the 2nd and the 5th centuries, extends for more than 8 km under Rome at several levels of depth excavated in tuff stones. Around the cemeterial galleries, there are several important iconographic testimonies of the paleo Christian age, from inscriptions and paintings to cubicula and small rooms. Among the latter, the Greek Chapel ( Figure 5) is one of the most significative representations of the Testament inside the complex. The little chapel, which takes its name from two Greek inscriptions inside it, stands out for the colored decorations and religious scenes, unique and particular for the historical period and artistic skills [41]. The hypogeum structures are critical ambient for the pictorial elements, which can be affected by biological attack, saline efflorescence, material swelling or cracking [42,43]. Due to the particular thermo-hygrometric conditions of the Priscilla catacomb environment, such as low temperature (~14 • C) and high humidity (~98%), procedures of the monitoring and documenting of the state of health were as important as urgent in order to keep alterations, detachments and the general conservation status under control. However, uncontrolled microclimatic parameters can be damaging also to electronic components, built for operation in ideal thermo-hygrometric conditions (T~15 ÷ 35 • C, RH-relative humidity~35 ÷ 75%) [44]. In this case, the solution to the hygrometric problems, i.e., condensation, was solved, covering the electronic components with a PVC (polyvinyl chloride)-protective sheet.
Due to the several architectonic elements, the complete 3D digitalization of the room required several stations, placing the electronic components in two positions and moving the scanning module along the chapel. For these reasons, the area was divided into multiple scans for a total of approx. 190 h.
the state of health were as important as urgent in order to keep alterations, detachments and the general conservation status under control. However, uncontrolled microclimatic parameters can be damaging also to electronic components, built for operation in ideal thermo-hygrometric conditions (T~15 ÷ 35 °C, RH-relative humidity~35 ÷ 75%) [44]. In this case, the solution to the hygrometric problems, i.e., condensation, was solved, covering the electronic components with a PVC (polyvinyl chloride)-protective sheet.

Tower Room in Saint Sebastian Gate of the Aurelian Walls
The city of Rome has many remains of ancient protection walls, dating back to the Roman imperial age. This important proof of the military strength of the Roman army surrounds several areas of the city and comprehends monumental gates, such as the Saint Sebastian one (Figure 6a). The architecture is typical of this type of structure, even if it has undergone several remakes over the centuries: one central arch between two lateral towers was developed into three floors [45,46]. The room of the right tower is particularly interesting from a historical and artistic point of view, because of the presence of charcoal drawings and inscriptions as testimonies of soldiers' lives in a military establishment in the late 19th century (Figure 6b). These inscriptions, illegible from the ground, have been the main object of the ENEA work, through 3D modelling and image enhancement of RGB-ITR data for the content extrapolation and reconstruction. The data acquisition process was carried out in 10 days, moving the system in seven different stations for the complete digitalization of each architectural structure (columns, vault). Due to the several architectonic elements, the complete 3D digitalization of the room required several stations, placing the electronic components in two positions and moving the scanning module along the chapel. For these reasons, the area was divided into multiple scans for a total of approx. 190 h.

Tower Room in Saint Sebastian Gate of the Aurelian Walls
The city of Rome has many remains of ancient protection walls, dating back to the Roman imperial age. This important proof of the military strength of the Roman army surrounds several areas of the city and comprehends monumental gates, such as the Saint Sebastian one (Figure 6a). The architecture is typical of this type of structure, even if it has undergone several remakes over the centuries: one central arch between two lateral towers was developed into three floors [45,46]. The room of the right tower is particularly interesting from a historical and artistic point of view, because of the presence of charcoal drawings and inscriptions as testimonies of soldiers' lives in a military establishment in the late 19th century (Figure 6b). These inscriptions, illegible from the ground, have been the main object of the ENEA work, through 3D modelling and image enhancement of RGB-ITR data for the content extrapolation and reconstruction. The data acquisition process was carried out in 10 days, moving the system in seven different stations for the complete digitalization of each architectural structure (columns, vault).

Egyptian Wooden Sarcophagus
The Egyptian anthropoid sarcophagus of Peftjauyauyaset (Figure 7a) belongs to the XXVI dynasty (7th-6th century BC) and is precious evidence of crafting skills of the Late Period of ancient Egypt.
This fragile artefact, coming from the Archaeological Museum of Milan, is made of Lebanon cedar wood, covered with painted plaster and intaglio carvings. The sarcophagus is completely decorated, both internally and externally, with polychromatic drawings and hieroglyphics. The general conservation status is particularly exceptional for what concerns the wooden structure and

Egyptian Wooden Sarcophagus
The Egyptian anthropoid sarcophagus of Peftjauyauyaset (Figure 7a) belongs to the XXVI dynasty (7th-6th century BC) and is precious evidence of crafting skills of the Late Period of ancient Egypt. This fragile artefact, coming from the Archaeological Museum of Milan, is made of Lebanon cedar wood, covered with painted plaster and intaglio carvings. The sarcophagus is completely decorated, both internally and externally, with polychromatic drawings and hieroglyphics. The general conservation status is particularly exceptional for what concerns the wooden structure and the decorations. The 3D models of the two part of the sarcophagus were requested from the restorers as documentation material before restoration. The digitalization process had to deal with a set of problems, such as reduced distances between object and system (<3 m), complex structures made of concavities and convexities, multiple materials and several incisions. The RGB-ITR system was placed at a fixed station (Figure 7b), while the two parts of the sarcophagus were moved to three different positions in order to scan entirely the artwork.

Laboratory Tests
Due to its very prototypal status, the IR scanner was tested in a laboratory environment on two painted samples. The first canvas (Figure 8a) presents three bands (blue, orange and light green) made with watercolor. From a naked-eye observation, an underlying drawing can be noticed although the different elements are not clearly visible. The second canvas (Figure 8b) has a wave motif, with a color gradient from black to greenish. The materials are acrylics, but from the direct observation of the work, the painting technique is not evident. The laboratory experiment (Figure 8c) was carried out, illuminating with IR-ITR scanner one canvas at a time at two different distances (at 10 m (Figure 8a) and at 5 m (Figure 8b)), in order to compare the quality of the results at a different distance range. By using a Thorlabs detector card [47], the IR laser beam was visualized on the canvas and the scanning area was defined through the ScanSystem software.

Laboratory Tests
Due to its very prototypal status, the IR scanner was tested in a laboratory environment on two painted samples. The first canvas (Figure 8a) presents three bands (blue, orange and light green) made with watercolor. From a naked-eye observation, an underlying drawing can be noticed although the different elements are not clearly visible. The second canvas (Figure 8b) has a wave motif, with a color gradient from black to greenish. The materials are acrylics, but from the direct observation of the work, the painting technique is not evident. The laboratory experiment (Figure 8c) was carried out, illuminating with IR-ITR scanner one canvas at a time at two different distances (at 10 m (Figure 8a) and at 5 m (Figure 8b)), in order to compare the quality of the results at a different distance range. By using a Thorlabs detector card [47], the IR laser beam was visualized on the canvas and the scanning area was defined through the ScanSystem software. motif, with a color gradient from black to greenish. The materials are acrylics, but from the direct observation of the work, the painting technique is not evident. The laboratory experiment (Figure 8c) was carried out, illuminating with IR-ITR scanner one canvas at a time at two different distances (at 10 m (Figure 8a) and at 5 m (Figure 8b)), in order to compare the quality of the results at a different distance range. By using a Thorlabs detector card [47], the IR laser beam was visualized on the canvas and the scanning area was defined through the ScanSystem software.

Results
The reported results were achieved using the instruments for a minimum of one hour to a maximum of one week, with post-processing phases duration from less than hours for preliminary 3D modelling up to several days for the complete merging of multiple scans or image enhancement. In Table 1, the main scanning parameters and difficulties of each case study reported in this paper are summarized.

3D Modelling and Image Enhancement
The digitalization of the San Brizio Chapel was carried out during day and night hours, independently from the high illumination that characterizes the room and strongly defeats photographs, as can be noticed in Figure 9.

3D Modelling and Image Enhancement
The digitalization of the San Brizio Chapel was carried out during day and night hours, independently from the high illumination that characterizes the room and strongly defeats photographs, as can be noticed in Figure 9. The final 3D model was built from the merging of multiple scans acquired with a very partial overlapping along the edges, in order to give reference points during the registration process, carried out by picking the same points in the two textures to register, as shown in Figure 10. The final 3D model was built from the merging of multiple scans acquired with a very partial overlapping along the edges, in order to give reference points during the registration process, carried out by picking the same points in the two textures to register, as shown in Figure 10.       The 3D modelling of the Greek Chapel required tens of scans, dividing the room into multiple sub-areas. The single scans were calibrated and then all registered with each other using itrAnalyzer software for the building of the final 3D model, partially shown in Figure 12. The 3D modelling of the Greek Chapel required tens of scans, dividing the room into multiple sub-areas. The single scans were calibrated and then all registered with each other using itrAnalyzer software for the building of the final 3D model, partially shown in Figure 12. In the case study of the Saint Sebastian tower, in addition to the 3D modelling (Figure 13a), the post-processing phases on RGB-ITR data included the application of 'affine' algorithm for letter detection and background removal (Figure 13b). The research has provided a partial reconstruction of the inscriptions contents through the extrapolation of single letters [48]. Further elaborations are needed for automatic word reconstructions based on letter recognition. In the case study of the Saint Sebastian tower, in addition to the 3D modelling (Figure 13a), the post-processing phases on RGB-ITR data included the application of 'affine' algorithm for letter detection and background removal (Figure 13b). The research has provided a partial reconstruction of the inscriptions contents through the extrapolation of single letters [48]. Further elaborations are needed for automatic word reconstructions based on letter recognition.
In the case study of the Saint Sebastian tower, in addition to the 3D modelling (Figure 13a), the post-processing phases on RGB-ITR data included the application of 'affine' algorithm for letter detection and background removal (Figure 13b). The research has provided a partial reconstruction of the inscriptions contents through the extrapolation of single letters [48]. Further elaborations are needed for automatic word reconstructions based on letter recognition.  [48]. (Elaboration carried out by ENEA team with the custom software itrAnalyzer).
The sarcophagus digitalization has represented an interesting instrumental challenge, both in terms of material and shape. The several concavities and convexities of the artefact requested different object positioning and multiple scans, translated into the registrations of several textures. Since the study is still ongoing, the results are not complete but promising, having achieved accurate digitalization of colors, materials and irregularities (Figure 14b), not well appreciable with laboratory artificial illumination (Figure 14a). The sarcophagus digitalization has represented an interesting instrumental challenge, both in terms of material and shape. The several concavities and convexities of the artefact requested different object positioning and multiple scans, translated into the registrations of several textures. Since the study is still ongoing, the results are not complete but promising, having achieved accurate digitalization of colors, materials and irregularities (Figure 14b), not well appreciable with laboratory artificial illumination (Figure 14a).

Infrared Imaging
The laboratory test on a three-color canvas has shown interesting details of the drawings underlying the superficial painting, barely visible to the naked eye (Figure 15a). Indeed, the IR image has clearly revealed different elements under the three watercolor bands (Figure 15b), providing an efficient means of investigation for preparatory drawings.

Infrared Imaging
The laboratory test on a three-color canvas has shown interesting details of the drawings underlying the superficial painting, barely visible to the naked eye ( Figure 15a). Indeed, the IR image has clearly revealed different elements under the three watercolor bands (Figure 15b), providing an efficient means of investigation for preparatory drawings.

Infrared Imaging
The laboratory test on a three-color canvas has shown interesting details of the drawings underlying the superficial painting, barely visible to the naked eye ( Figure 15a). Indeed, the IR image has clearly revealed different elements under the three watercolor bands (Figure 15b), providing an efficient means of investigation for preparatory drawings.  The scan on the acrylic canvas ( Figure 16a) has provided details on the painting technique, revealing how the nuances of the black waves have been realized before the definitive and visible drawing (Figure 16b). The scan on the acrylic canvas ( Figure 16a) has provided details on the painting technique, revealing how the nuances of the black waves have been realized before the definitive and visible drawing (Figure 16b).

Conclusions
Image techniques and 3D modelling are nowadays widely employed in the CH Conservation Science, which disclose a modern, non-invasive and engaging analysis tool. Several commercial systems are available on the market for 3D modelling, but they often require the complementarity with other techniques with limitation in terms of illumination conditions and spatial resolution.

Conclusions
Image techniques and 3D modelling are nowadays widely employed in the CH Conservation Science, which disclose a modern, non-invasive and engaging analysis tool. Several commercial systems are available on the market for 3D modelling, but they often require the complementarity with other techniques with limitation in terms of illumination conditions and spatial resolution. Likewise, close-range imaging, such as filter-wheel cameras, has distance and object size constraints. In this paper, two prototypal laser scanners using n-laser stimuli have been presented in order to demonstrate the quality, efficacy and the versatility of this methodology in this application field as a unique means for 3D digitalization and IR layering inspections. The color laser scanner, called RGB-ITR, has been used for 3D modelling and in-depth analyses from high-quality image enhancement, proving to handle critical surrounding conditions greatly, such as high humidity and great lighting, and irregular material, such as wooden anthropoid sarcophagi. The IR system, called IT-ITR, has been tested on laboratory samples, attesting validity for inspection under layers of different painting materials (acrylic and watercolor) at up to 10 m of distance from the system, contrary to close-range instruments. The results have shown the potentialities of the two laser scanners and their versatility in terms of environmental circumstances and materials, two important but unstable factors in the CH field. The ITR images can be used for conservation purposes for their high detailing and re-usability over time. Future plans include the implementation of laser sources, even using the same scanner, in order to achieve a multispectral scanner as a multipurpose system for applications in a wider range of materials and not exclusively limited to CH. The research group is working on a new version of this scanner, which will host 7 wavelengths-one in the near ultraviolet spectrum (380 nm), four in the visible spectrum (441, 530, 580, 660 nm) and two in the infrared (800, 1500 nm) spectrum-with the aim to develop a multispectral (up to several ten meters) high-density point cloud remote sensor Funding: Part of the research presented in this paper was performed within CO.B.RA. project and funded by regional grant (lr13/2008 project n. 1031).