Non-Structural Vibro-Compressed Concrete Incorporating Industrial Wastes

: This study presents more eco-efﬁcient concrete formulations for precast vibro-compressed masonry blocks. The proposed formulations incorporated industrial waste, glass powder (GP), and quartz powder (QP), in which natural aggregate was partially replaced by QP (10%) and Portland cement by GP (10% and 20%). The best combination of powder materials, water, and admixture was optimised at mortar level, considering a “zero slump” criteria and compressive strength. Afterwards, studies at concrete level followed. Specimens were vibrated and compressed in laboratory and immediately demoulded, aiming to simulate the industrial process. The compressive strength decreased when GP and QP were used alone; however, when combining 10% GP as cement replacement + 10% QP as ﬁne aggregate replacement, the compressive strength increased by approximately 26.6% compared to the reference concrete. Water absorption results varied between 8.92 and 17.9%, and the lowest absorption was obtained by concrete specimens incorporating 20% GP. The UPV presented a narrow range of variation among all concrete mixtures under study, around 2–2.5 km/s at 28 days, whereas electrical resistivity was achieved at 28 days, at 20,000 and 25,000 ohms. Although there were some limitations of the casting process at the laboratory scale, the research results showed promising results, and it seems feasible to use this waste as a substitute for non-renewable raw materials in the production of concrete on an industrial scale. This can provide added value to abundant local wastes while contributing to a circular concrete economy.


Introduction
Construction plays a fundamental role in a country's socio-economic development since it promotes a sustainable built environment, greener and more inclusive societies, improvements to people's quality of life, economic growth, and job creation.The predicted growth in the world's population (by 2050, it is expected to increase by more than 2000 million people [1]) and the need for housing and infrastructure will further highlight the role of the construction sector.Thus, construction stakeholders-engineers, architects, construction managers, urban planners, etc.-face the great challenge of promoting the sustainable development of construction [2].
On the other hand, the escalating growth rates of the global population directly impact production volumes.Consequently, there is a heightened generation of industrial waste, which is a significant concern in the modern world.As industries continue to expand and diversify, the quantity and complexity of industrial waste materials have also increased.These waste products can encompass a broad spectrum of materials, including hazardous chemicals, non-recyclable plastics, and various by-products of manufacturing processes, which, if disposed of irregularly-for example, in landfill sites-can cause major environmental problems.Effective waste management practices, such as recycling, reusing, and responsible disposal, are paramount to mitigate the environmental and societal impacts caused by industrial waste generation [3].
The World Green Building Council has identified that building materials can meet at least 9 of the 17 Sustainable Development Goals of the 2030 Agenda [4].Thus, there is a growing interest in using greener materials, namely locally available materials and those including abundant waste or by-products with no added value.This is particularly true for the concrete products industry, as concrete is the most consumed material in the world after water.Concrete's ability to incorporate waste or by-products provides a key opportunity to boost the efficient use of resources, moving towards a cleaner and more circular economy and helping to make it more resource-efficient and competitive [5][6][7].
Glass is widely used in daily life, as it is durable, non-porous, and resistant to chemicals, making it versatile for various applications.However, there are significant problems with its irregular disposal in landfills, as glass products are not biodegradable.Approximately 130 million tons of glass are produced annually [8].But in many countries, much of this material is not recycled.In the United States alone, 12.3 million tons were produced in 2018; of these, only 31.3% were estimated to be recycled.All of the rest were deposited in landfills [9].In the European Union, around 80.1% of glass bottles and jars were collected for recycling in 2021 [10].About 980 000 tons of waste glass are produced in Brazil, but only 47% of this material is recycled [11].
These figures show how much needs to be recycled and reused.As a result, GP has been under consideration for inclusion in concrete to replace both aggregates and cement.GP is particularly interesting as a supplementary cementitious material since glass particles smaller than 75 µm exhibit relevant pozzolanic behaviour.In this context, the silica contained in the glass interacts with calcium hydrates (Ca(OH) 2 ), resulting in the formation of calcium silicate hydrate (CSH) [12].Promising results have been observed in the literature, as some of the following examples indicate.The mechanical strengths of mortar containing GP as a cement substitute increased significantly between 28 and 90 days, indicating pozzolanic activity [13].Another investigation into GP as a cement substitute, but in three different grain size fractions, 45, 75, and 150 µm, concluded that grain size is inversely proportional to its pozzolanic activity, i.e., the smaller the size of the glass powder, the better the results [14].Another study found that compressive and flexural strengths increased up to a 20% substitution rate of GP with cement, and then these properties gradually decreased as the substitution content increased [15].In addition, ultrahigh performance cementitious composite incorporating GP with different substitution proportions, namely, 0%, 10%, 20%, 30% and 50%, concluded that its addition at different levels resulted in high mechanical strength [16].Also, research into ultra-high-performance concrete showed that the higher the GP content, the higher the workability [17].
On the other hand, quartz powder (QP) is waste from quartz processing, a mineral stone composed of silica [18].Some studies show that QP can be used as an SMC or fine aggregate in cement-based materials.QP is chemically inert at room temperature [19].This characteristic favours the acceleration of the clinker hydration reaction [20].Despite the use of QP usually concerning high-and ultra-high-performance concrete, there are studies on its application in architectural white concrete, pointing out the great feasibility of its application [21].
As such, both GP and QP have great potential for incorporation into the construction industry in the manufacture of concrete, with engineering and environmental benefits.

Research Significance and Objectives
Concrete masonry block formulations (see Figure 1) comprise cement, aggregates, and water.It can be produced by manual, pneumatic, or hydraulic equipment using vibro-compaction and immediate extrusion.To ensure compaction and homogeneity, the moulded concrete must follow a careful process without cracks and damage that could lead to poor settlement, which may compromise strength and durability properties [22].Some studies have pointed to the possibility of incorporating waste into concrete blocks [23][24][25][26][27].However, most studies used recycled aggregate or plastic waste as coarse aggregate replacement.Incorporating steel slag in concrete blocks up to 80%, partially replacing natural aggregates, showed promising results [28].Another study showed the feasibility of producing recycled concrete blocks by incorporating recycled aggregates from the blocks [29].However, to the best of the authors' knowledge, no studies were found on incorporating GP and QP for concrete masonry block production as cement and fine aggregate replacement.
The main objective of this work is to develop more eco-efficient concrete mixes for vibro-compressed non-structural concrete blocks.As such, using QP, a mining waste, is foreseen as a partial replacement for the fine aggregate and incorporating ground glass waste as a substitute for a fraction of Portland cement.Initially, compositions at the mortar level (cement, glass powder, water, admixture, and fine aggregate) were studied.Afterwards, a concrete study was conducted using the best cementitious materials combination.Subsequently, concrete characterisation was carried out, including mechanical strength, young modulus, water absorption, electrical resistivity, and ultrasonic pulse velocity.To achieve the main objective, the following specific objectives are outlined:

•
Develop mortar compositions considering performance requirements for vibrocompressed concrete blocks, particularly workability and mechanical strength, while maximising the incorporation of QP and GP.

•
Scale up the optimal mortars to concrete and proceed with their characterisation regarding workability, mechanical strength, water absorption, and non-destructive tests.

•
Propose cleaner concrete compositions for the precast concrete block industry.

Raw Material Characterisation
The materials selection was based on locally available raw materials in the Portuguese market, except GP and QP, which were obtained from the glass recycling and mining industries, respectively.The glass waste was wet milled on an industry scale (d50 = 35 µm) until it reached a particle size similar to cement.The QP was used as supplied by the mining industry and only dried until constant mass before use (d50 = 48 µm).
For mortar and concrete tests, Portland cement CEM I 42.5R (complying with EN 197-1 [30]) GP, QP, silicious sand, and gravel (only for concrete) were used.In addition, a commercially available admixture for non-structural concrete with a specific gravity of 1250 kg/m 3 and 37.0% solids content was introduced.Table 1 summarises the fundamental characterisation of the chemical, physical, and mechanical properties of cement, GP, and QP.Some studies have pointed to the possibility of incorporating waste into concrete blocks [23][24][25][26][27].However, most studies used recycled aggregate or plastic waste as coarse aggregate replacement.Incorporating steel slag in concrete blocks up to 80%, partially replacing natural aggregates, showed promising results [28].Another study showed the feasibility of producing recycled concrete blocks by incorporating recycled aggregates from the blocks [29].However, to the best of the authors' knowledge, no studies were found on incorporating GP and QP for concrete masonry block production as cement and fine aggregate replacement.
The main objective of this work is to develop more eco-efficient concrete mixes for vibro-compressed non-structural concrete blocks.As such, using QP, a mining waste, is foreseen as a partial replacement for the fine aggregate and incorporating ground glass waste as a substitute for a fraction of Portland cement.Initially, compositions at the mortar level (cement, glass powder, water, admixture, and fine aggregate) were studied.Afterwards, a concrete study was conducted using the best cementitious materials combination.Subsequently, concrete characterisation was carried out, including mechanical strength, young modulus, water absorption, electrical resistivity, and ultrasonic pulse velocity.To achieve the main objective, the following specific objectives are outlined:

•
Develop mortar compositions considering performance requirements for vibrocompressed concrete blocks, particularly workability and mechanical strength, while maximising the incorporation of QP and GP.

•
Scale up the optimal mortars to concrete and proceed with their characterisation regarding workability, mechanical strength, water absorption, and non-destructive tests.

•
Propose cleaner concrete compositions for the precast concrete block industry.

Raw Material Characterisation
The materials selection was based on locally available raw materials in the Portuguese market, except GP and QP, which were obtained from the glass recycling and mining industries, respectively.The glass waste was wet milled on an industry scale (d 50 = 35 µm) until it reached a particle size similar to cement.The QP was used as supplied by the mining industry and only dried until constant mass before use (d 50 = 48 µm).
For mortar and concrete tests, Portland cement CEM I 42.5R (complying with EN 197-1 [30]) GP, QP, silicious sand, and gravel (only for concrete) were used.In addition, a commercially available admixture for non-structural concrete with a specific gravity of 1250 kg/m 3 and 37.0% solids content was introduced.Table 1 summarises the fundamental characterisation of the chemical, physical, and mechanical properties of cement, GP, and QP.The particle size of cement, GP, and QP was measured by the laser method through Mastersizer 2000 and using the Mie Model according to the recommendations of ISO 13320.The sieving method prescribed in EN 933-1 [31] determined the particle size of the aggregates.Figure 2 presents the particle size distribution of solid materials.It is important to note that cement, GP, and QP were determined using the laser method, and sand and gravel were determined using the sieving method.The particle size of cement, GP, and QP was measured by the laser method through Mastersizer 2000 and using the Mie Model according to the recommendations of ISO 13320.The sieving method prescribed in EN 933-1 [31] determined the particle size of the aggregates.Figure 2 presents the particle size distribution of solid materials.It is important to note that cement, GP, and QP were determined using the laser method, and sand and gravel were determined using the sieving method.
The morphology of cement, GP, and QP particles was observed using SEM in secondary electron (SE) mode.As shown in Figure 2, waste glass particles presented a wide size range (corroborating the particle size distribution analysis in Figure 3), and some particles presented sharp edges.The morphology of cement, GP, and QP particles was observed using SEM in secondary electron (SE) mode.As shown in Figure 2, waste glass particles presented a wide size range (corroborating the particle size distribution analysis in Figure 3), and some particles presented sharp edges.

Preliminary Mortar Studies
Since both GP and QP are "innovative" materials applied in vibro-compressed concrete for concrete blocks, a step-by-step process was required to find an appropriate mix composition.Initially, the best combination of powder materials, water, and superplasticiser was studied at the mortar level.
The mortars were produced using a mortar mixture according to EN 196-1 [32], using the low-speed option.The following pre-established sequence was adopted: first, the solid materials were mixed for 30 s, then water and the admixture were incorporated, mixing for an additional 150 s.Afterwards, any material adhering to the drum and the paddle was carefully removed with a spatula.Finally, a final mix was performed for 60 s at the same speed.The study included 11 different proportions of mortar mixtures, shown in Table 2, including the workability and compressive strength results (two last lines).
The workability was measured immediately after production.Requirements for the vibro-compressed concrete of mortar were defined as "zero slump".For that, a flow table and a brass cone in accordance with EN 12350-5 [33] were used.For the slump flow test, the fresh mortar was cast in two layers of the brass cone, and each layer was tamped 10 times with a special tamping rod.After cutting off the extra mortar by drawing a straight edge with a trowel, the brass cone mould was lifted away from the mortar.If the fresh mortar kept the brass cone shape without deformation or material loss, as depicted in Figure 4, it was considered a valid mortar mixture for vibro-compressed concrete.

Preliminary Mortar Studies
Since both GP and QP are "innovative" materials applied in vibro-compressed concrete for concrete blocks, a step-by-step process was required to find an appropriate mix composition.Initially, the best combination of powder materials, water, and superplasticiser was studied at the mortar level.
The mortars were produced using a mortar mixture according to EN 196-1 [32], using the low-speed option.The following pre-established sequence was adopted: first, the solid materials were mixed for 30 s, then water and the admixture were incorporated, mixing for an additional 150 s.Afterwards, any material adhering to the drum and the paddle was carefully removed with a spatula.Finally, a final mix was performed for 60 s at the same speed.The study included 11 different proportions of mortar mixtures, shown in Table 2, including the workability and compressive strength results (two last lines).The workability was measured immediately after production.Requirements for the vibro-compressed concrete of mortar were defined as "zero slump".For that, a flow table and a brass cone in accordance with EN 12350-5 [33] were used.For the slump flow test, the fresh mortar was cast in two layers of the brass cone, and each layer was tamped 10 times with a special tamping rod.After cutting off the extra mortar by drawing a straight edge with a trowel, the brass cone mould was lifted away from the mortar.If the fresh mortar kept the brass cone shape without deformation or material loss, as depicted in Figure 4, it was considered a valid mortar mixture for vibro-compressed concrete.Then, prismatic specimens (40 × 40 × 160 mm 3 ) were cast and compacted using a vibration table for 30 s. Specimens remained for 48 h in the moulds and were then air cured in a controlled environment (Temperature 20 ± 2 °C and HR = 50 ± 2%) until the testing age (mechanical strength).The tests were performed on mixes 1 to 8, on prismatic test specimens, at an age of 7 days (see Table 2).Mixtures 9, 10, and 11 were tested at 28 days (see Table 2).
Several trials were made to set the cement, water, and admixture content, as seen in Table 2 (mix 1 to mix 8).Then, the ideal cement replacement dosage with GP and QP was determined.Mixtures containing 10% cement replacement by GP, by weight, (mix.9 and mix. 10, respectively) were produced and tested at the fresh state (to check "zero slump" condition previously described), and the mechanical strength was tested at 28 days.Fresh properties and the mechanical strength of the studied mortars with "zero slump" can be seen in Table 2.It can be observed, as expected, that cement replacement decreased the mechanical strength.These mixtures were chosen as a basis for the experimental concrete.

Concrete Mix Design
Mortar properties adequate for vibro-compressed were well defined at this level, and if target values are achieved, in the next stage, tests on concrete, although essential, are reduced to a minimum.Final trials at the concrete level were necessary to quantify the coarse aggregate amount, adjust admixture dosage (if necessary), and confirm the "zero slump" of the formulated mixtures.
The most common concrete mix design methods are based on experiments and reference curves.The experimental method requires a significant workforce and can be very time-consuming.The reference curve methods result from research work developed by specialists such as Faury, Joisel, and Dreux and are still widely used today.These methods aim to achieve an ideal mix design curve that includes aggregates and cement and also allows for the establishment of a granulometric curve of maximum compactness with the available aggregates.
The concrete mix design methods employed in this current work were based on the Faury and ACI recommendations for zero slump concrete, namely Annex 5 of the ACI 211.3R-02 [34] guide, which establishes a set of rules for obtaining the composition of concrete that is used in the production of masonry blocks and whose manufacture is carried out using vibro-compressor machines.
The best combination of aggregates was calculated in automatic Excel spreadsheets based on the Faury method, including the American recommendations for zero slump concrete.An example of Faury curves used in this current work is presented in Figure 5. Considering that 1 m 3 of concrete is composed of the sum of its constituents-in this case, the binder (cement and GP), water, aggregates, and voids-and since the density of each Then, prismatic specimens (40 × 40 × 160 mm 3 ) were cast and compacted using a vibration table for 30 s. Specimens remained for 48 h in the moulds and were then air cured in a controlled environment (Temperature 20 ± 2 • C and HR = 50 ± 2%) until the testing age (mechanical strength).The tests were performed on mixes 1 to 8, on prismatic test specimens, at an age of 7 days (see Table 2).Mixtures 9, 10, and 11 were tested at 28 days (see Table 2).
Several trials were made to set the cement, water, and admixture content, as seen in Table 2 (mix 1 to mix 8).Then, the ideal cement replacement dosage with GP and QP was determined.Mixtures containing 10% cement replacement by GP, by weight, (mix.9 and mix. 10, respectively) were produced and tested at the fresh state (to check "zero slump" condition previously described), and the mechanical strength was tested at 28 days.Fresh properties and the mechanical strength of the studied mortars with "zero slump" can be seen in Table 2.It can be observed, as expected, that cement replacement decreased the mechanical strength.These mixtures were chosen as a basis for the experimental concrete.

Concrete Mix Design
Mortar properties adequate for vibro-compressed were well defined at this level, and if target values are achieved, in the next stage, tests on concrete, although essential, are reduced to a minimum.Final trials at the concrete level were necessary to quantify the coarse aggregate amount, adjust admixture dosage (if necessary), and confirm the "zero slump" of the formulated mixtures.
The most common concrete mix design methods are based on experiments and reference curves.The experimental method requires a significant workforce and can be very time-consuming.The reference curve methods result from research work developed by specialists such as Faury, Joisel, and Dreux and are still widely used today.These methods aim to achieve an ideal mix design curve that includes aggregates and cement and also allows for the establishment of a granulometric curve of maximum compactness with the available aggregates.
The concrete mix design methods employed in this current work were based on the Faury and ACI recommendations for zero slump concrete, namely Annex 5 of the ACI 211.3R-02 [34] guide, which establishes a set of rules for obtaining the composition of concrete that is used in the production of masonry blocks and whose manufacture is carried out using vibro-compressor machines.
The best combination of aggregates was calculated in automatic Excel spreadsheets based on the Faury method, including the American recommendations for zero slump concrete.An example of Faury curves used in this current work is presented in Figure 5. Considering that 1 m 3 of concrete is composed of the sum of its constituents-in this case, the binder (cement and GP), water, aggregates, and voids-and since the density of each of these materials is known (see Section 3.1), it is possible to quantify each of the constituents by mass, through the proportion adopted between them.The concrete mixture proportions are presented in Table 3.
Recycling 2024, 9, x FOR PEER REVIEW 7 of 19 of these materials is known (see Section 3.1), it is possible to quantify each of the constituents by mass, through the proportion adopted between them.The concrete mixture proportions are presented in Table 3.  Mixes were prepared in the laboratory in 15 L batches and mixed in an open pan mixer.The mixing sequence consisted of mixing sand and gravel with 25% of the mixing water for 1 min, waiting for 2 min for absorption and adding the powder materials, and adding the remaining water with the admixture and mixing the concrete for 5 min.
Afterwards, a tripartite metallic mould with wooden bases with a 200 mm height and 100 mm diameter was filled with concrete and placed on top of the Retsch A 200 Basic sieve vibration machine; see Figure 6a.The vibration equipment is programmed for a fixed vibration frequency of 60 Hz, but the vibration time and amplitude are adjustable.The amplitude ranges from 1 to 100%, representing a 0 to 3 mm variation in millimetres.The moulds were filled in two concrete layers, each one vibrated for 30 s. Regarding amplitude, 70% was adopted on the scale of the machine, which is equivalent to 2.1 mm, according to previous work [35].Immediately after the end of the vibration, the specimens were transported to the Instron 300 DX press machine, and the load was applied at increments of 0.5 mm per second.The compression load varied between 50 and 75 s until a maximum load of 16 (±1) kN was reached; see Figure 6b.The load was maintained for 1 min.These steps aimed to simulate the vibro compression process, even though, at a laboratory scale, it was not possible to apply vibration and compression simultaneously.The specimens were demoulded immediately afterwards.The tripartite mould was dismantled, while the specimen remained on the wooden base; see Figure 6-c,d.
For each concrete mix composition (presented in Table 3), 9 cylindrical specimens with a 200 mm height and 100 mm diameter were produced."In situ" curing chambers were prepared, as transporting the specimens to the laboratory curing room would not have been recommended due to the risk of the specimens falling apart during transportation.These in situ curing chambers were prepared using inverted plastic boxes,

Concrete Specimens Production
Mixes were prepared in the laboratory in 15 L batches and mixed in an open pan mixer.The mixing sequence consisted of mixing sand and gravel with 25% of the mixing water for 1 min, waiting for 2 min for absorption and adding the powder materials, and adding the remaining water with the admixture and mixing the concrete for 5 min.
Afterwards, a tripartite metallic mould with wooden bases with a 200 mm height and 100 mm diameter was filled with concrete and placed on top of the Retsch A 200 Basic sieve vibration machine; see Figure 6a.The vibration equipment is programmed for a fixed vibration frequency of 60 Hz, but the vibration time and amplitude are adjustable.The amplitude ranges from 1 to 100%, representing a 0 to 3 mm variation in millimetres.The moulds were filled in two concrete layers, each one vibrated for 30 s. Regarding amplitude, 70% was adopted on the scale of the machine, which is equivalent to 2.1 mm, according to previous work [35].Immediately after the end of the vibration, the specimens were transported to the Instron 300 DX press machine, and the load was applied at increments of 0.5 mm per second.The compression load varied between 50 and 75 s until a maximum load of 16 (±1) kN was reached; see Figure 6b.The load was maintained for 1 min.These steps aimed to simulate the vibro compression process, even though, at a laboratory scale, it was not possible to apply vibration and compression simultaneously.The specimens were demoulded immediately afterwards.The tripartite mould was dismantled, while the specimen remained on the wooden base; see Figure 6c,d.
For each concrete mix composition (presented in Table 3), 9 cylindrical specimens with a 200 mm height and 100 mm diameter were produced."In situ" curing chambers were prepared, as transporting the specimens to the laboratory curing room would not have been recommended due to the risk of the specimens falling apart during transportation.These in situ curing chambers were prepared using inverted plastic boxes, as shown in Figure 6e, and were kept in those conditions for 48 h.Afterwards, the specimens were moved to a controlled environment room (Temperature 20 ± 2 • C and HR = 50 ± 2%) and separated from wooden bases.
as shown in Figure 6e, and were kept in those conditions for 48 h.Afterwards, the specimens were moved to a controlled environment room (Temperature 20 ± 2 °C and HR = 50 ± 2%) and separated from wooden bases.
The UPV and electrical resistivity tests at predefined ages were performed in the controlled environment room.The water absorption, modulus of elasticity, and compressive strength were assessed at 28 days.

Mechanical Strength and Young's Modulus
The compression tests were carried out in accordance with NP EN 12390-6 [36], with the following adaptations.The test was performed in cylindrical concrete specimens with a 200 mm height and 100 mm diameter (six for each concrete mixture, see Table 3), produced as described in Section 3.3.1.Additionally, the test was performed in displacement control, in which increments of 0.01 mm/s were applied through an Instron 300 DX press machine, as depicted in Figure 7. Previously, a layer of cement grout was applied to regularise the surfaces of the concrete specimens.Young's modulus was measured following the DIN 1048-5 [37], except for the load, which had to be reduced to 0.06 MPa/s to obtain a typical diagram for this test.The test was carried out on 3 cylindrical specimens for each concrete mixture; see Figure 8.The maximum load applied during the test to determine the modulus of elasticity of the concrete was calculated according to the compressive strength previously determined.The UPV and electrical resistivity tests at predefined ages were performed in the controlled environment room.The water absorption, modulus of elasticity, and compressive strength were assessed at 28 days.

Mechanical Strength and Young's Modulus
The compression tests were carried out in accordance with NP EN 12390-6 [36], with the following adaptations.The test was performed in cylindrical concrete specimens with a 200 mm height and 100 mm diameter (six for each concrete mixture, see Table 3), produced as described in Section 3.3.1.Additionally, the test was performed in displacement control, in which increments of 0.01 mm/s were applied through an Instron 300 DX press machine, as depicted in Figure 7. Previously, a layer of cement grout was applied to regularise the surfaces of the concrete specimens.
as shown in Figure 6e, and were kept in those conditions for 48 h.Afterwards, th specimens were moved to a controlled environment room (Temperature 20 ± 2 °C and H = 50 ± 2%) and separated from wooden bases.
The UPV and electrical resistivity tests at predefined ages were performed in th controlled environment room.The water absorption, modulus of elasticity, an compressive strength were assessed at 28 days.

Mechanical Strength and Young's Modulus
The compression tests were carried out in accordance with NP EN 12390-6 [36], wit the following adaptations.The test was performed in cylindrical concrete specimens wit a 200 mm height and 100 mm diameter (six for each concrete mixture, see Table 3 produced as described in Section 3.3.1.Additionally, the test was performed i displacement control, in which increments of 0.01 mm/s were applied through an Instro 300 DX press machine, as depicted in Figure 7. Previously, a layer of cement grout wa applied to regularise the surfaces of the concrete specimens.Young's modulus was measured following the DIN 1048-5 [37], except for the load which had to be reduced to 0.06 MPa/s to obtain a typical diagram for this test.The tes was carried out on 3 cylindrical specimens for each concrete mixture; see Figure 8. Th maximum load applied during the test to determine the modulus of elasticity of th concrete was calculated according to the compressive strength previously determined.Young's modulus was measured following the DIN 1048-5 [37], except for the load, which had to be reduced to 0.06 MPa/s to obtain a typical diagram for this test.The test was carried out on 3 cylindrical specimens for each concrete mixture; see Figure 8.The maximum load applied during the test to determine the modulus of elasticity of the concrete was calculated according to the compressive strength previously determined.

Water Absorption by Immersion
Water absorption by immersion was determined according to NBR 9778 [38].In brief, after curing for 28 days in a controlled environment room (Temperature 20 ± 2 °C and HR = 50 ± 2%), the concrete cylindrical specimens were oven-dried at 105 ± 5 °C for 72 h, as shown in Figure 9a.Afterwards, the samples were cooled in the laboratory environment, and the dry mass (ms) was recorded.Then, the concrete specimens were water immersed for 72 h at 20 ± 2 °C, as seen in Figure 9b.Finally, the specimens were taken to a container of hot water, where they were heated up to boiling for over 5 h.After 5 h, the heat source was switched off, and the specimens were cooled to reach room temperature so that the immersed masses (mi) could be determined using a hydrostatic scale to determine the saturated mass (msat).With the recorded values in the previous steps, it was possible to obtain various concrete parameters in accordance with NBR 9778 [38], such as calculating water absorption (A) in percentage using the following expression: Additionally, the void index (Iv) can be determined by this equation: Furthermore, the specific mass of the dry sample (ρs) and the saturated sample (ρsat) can be calculated using these expressions:

Water Absorption by Immersion
Water absorption by immersion was determined according to NBR 9778 [38].In brief, after curing for 28 days in a controlled environment room (Temperature 20 ± 2 • C and HR = 50 ± 2%), the concrete cylindrical specimens were oven-dried at 105 ± 5 • C for 72 h, as shown in Figure 9a.Afterwards, the samples were cooled in the laboratory environment, and the dry mass (ms) was recorded.Then, the concrete specimens were water immersed for 72 h at 20 ± 2 • C, as seen in Figure 9b.Finally, the specimens were taken to a container of hot water, where they were heated up to boiling for over 5 h.After 5 h, the heat source was switched off, and the specimens were cooled to reach room temperature so that the immersed masses (mi) could be determined using a hydrostatic scale to determine the saturated mass (msat).

Water Absorption by Immersion
Water absorption by immersion was determined according to NBR 9778 [38].In brief, after curing for 28 days in a controlled environment room (Temperature 20 ± 2 °C and HR = 50 ± 2%), the concrete cylindrical specimens were oven-dried at 105 ± 5 °C for 72 h, as shown in Figure 9a.Afterwards, the samples were cooled in the laboratory environment, and the dry mass (ms) was recorded.Then, the concrete specimens were water immersed for 72 h at 20 ± 2 °C, as seen in Figure 9b.Finally, the specimens were taken to a container of hot water, where they were heated up to boiling for over 5 h.After 5 h, the heat source was switched off, and the specimens were cooled to reach room temperature so that the immersed masses (mi) could be determined using a hydrostatic scale to determine the saturated mass (msat).With the recorded values in the previous steps, it was possible to obtain various concrete parameters in accordance with NBR 9778 [38], such as calculating water absorption (A) in percentage using the following expression: Additionally, the void index (Iv) can be determined by this equation: Furthermore, the specific mass of the dry sample (ρs) and the saturated sample (ρsat) can be calculated using these expressions: With the recorded values in the previous steps, it was possible to obtain various concrete parameters in accordance with NBR 9778 [38], such as calculating water absorption (A) in percentage using the following expression: Additionally, the void index (Iv) can be determined by this equation: Furthermore, the specific mass of the dry sample (ρs) and the saturated sample (ρsat) can be calculated using these expressions: (3)

UPV and Electrical Resistivity
Concrete UPV was assessed according to NP EN 12504-4 [39] on cylindrical specimens (φ = 100 mm; h = 200 mm).The ultrasound velocity was measured on 6 specimens for each concrete mixture under study (Table 3); see Figure 10.The direct transmission method was used, and the ultrasound propagation speed calculation corresponded to the quotient between the length of the specimen and the time it took to cross that same path.Concrete UPV was assessed according to NP EN 12504-4 [39] on cylindrica specimens (ϕ = 100 mm; h = 200 mm).The ultrasound velocity was measured on specimens for each concrete mixture under study (Table 3); see Figure 10.The direc transmission method was used, and the ultrasound propagation speed calculatio corresponded to the quotient between the length of the specimen and the time it took cross that same path.Concrete electrical resistivity was assessed using a two-electrode setup on the sam six concrete cylindrical specimens (ϕ = 100 mm; h = 200 mm).For the direct test, a low frequency electrical current was passed between the two electrodes (two stainless stee plates) while the voltage change was measured (see Figure 11).To ensure good electrica contact between the specimen and electrodes, a wet sponge was positioned, and a forc was applied to maintain a constant and uniform stress distribution over the entire surfac of the specimen.Resistivity was obtained from the electrical resistance (calculated from the potential response using Ohm's law) and a geometric factor, applying Equation (5).
where , voltage (Volts); , current (A); , length (m); and  (m 2 ) the cross area of th test specimen through which the current passed.Concrete electrical resistivity was assessed using a two-electrode setup on the same six concrete cylindrical specimens (φ = 100 mm; h = 200 mm).For the direct test, a lowfrequency electrical current was passed between the two electrodes (two stainless steel plates) while the voltage change was measured (see Figure 11).To ensure good electrical contact between the specimen and electrodes, a wet sponge was positioned, and a force was applied to maintain a constant and uniform stress distribution over the entire surface of the specimen.Resistivity was obtained from the electrical resistance (calculated from the potential response using Ohm's law) and a geometric factor, applying Equation (5).
where V, voltage (Volts); I, current (A); L, length (m); and A (m 2 ) the cross area of the test specimen through which the current passed.Since all the specimens were at the same moisture in a controlled environment room (Temperature 20 ± 2 • C and HR = 50 ± 2%), resistivity testing may provide information about pore connectivity and the resistance of concrete to the penetration of liquid or gas substances.Since all the specimens were at the same moisture in a controlled environment room (Temperature 20 ± 2 °C and HR = 50 ± 2%), resistivity testing may provide information about pore connectivity and the resistance of concrete to the penetration of liquid or gas substances.

Mechanical Strength and Young's Modulus
The compressive strength test results for the cylindrical concrete specimens are shown in Figure 12.For each concrete mixture (see Table 3), six specimens were tested at 28 days; the average result is considered the compressive strength at 28 days.As can be perceived, the compressive strength of the concrete mixtures under study varied between 2.0 and 5.4 MPa.The highest compressive strength was reached for GP10QP10 concrete, which was very promising, followed by the reference mixture (CTL), which achieved 4.2 MPa.Partial cement replacement by GP decreased compressive strength, as observed in previous research.The same occurred for QP10 concrete; a partial sand replacement by QP resulted in a slight decrease compared to the CTL mixture.Concerning GP, a lower PSD would be beneficial for pozzolanic ability [40][41][42][43][44][45][46][47][48], since from

Mechanical Strength and Young's Modulus
The compressive strength test results for the cylindrical concrete specimens are shown in Figure 12.For each concrete mixture (see Table 3), six specimens were tested at 28 days; the average result is considered the compressive strength at 28 days.Since all the specimens were at the same moisture in a controlled environment room (Temperature 20 ± 2 °C and HR = 50 ± 2%), resistivity testing may provide information about pore connectivity and the resistance of concrete to the penetration of liquid or gas substances.

Mechanical Strength and Young's Modulus
The compressive strength test results for the cylindrical concrete specimens are shown in Figure 12.For each concrete mixture (see Table 3), six specimens were tested at 28 days; the average result is considered the compressive strength at 28 days.As can be perceived, the compressive strength of the concrete mixtures under study varied between 2.0 and 5.4 MPa.The highest compressive strength was reached for GP10QP10 concrete, which was very promising, followed by the reference mixture (CTL), which achieved 4.2 MPa.Partial cement replacement by GP decreased compressive strength, as observed in previous research.The same occurred for QP10 concrete; a partial sand replacement by QP resulted in a slight decrease compared to the CTL mixture.Concerning GP, a lower PSD would be beneficial for pozzolanic ability [40][41][42][43][44][45][46][47][48], since from As can be perceived, the compressive strength of the concrete mixtures under study varied between 2.0 and 5.4 MPa.The highest compressive strength was reached for GP10QP10 concrete, which was very promising, followed by the reference mixture (CTL), which achieved 4.2 MPa.Partial cement replacement by GP decreased compressive strength, as observed in previous research.The same occurred for QP10 concrete; a partial sand replacement by QP resulted in a slight decrease compared to the CTL mixture.Concerning GP, a lower PSD would be beneficial for pozzolanic ability [40][41][42][43][44][45][46][47][48], since from past research, the smaller the particle size, the higher the pozzolanic reactivity of the glass powder particles [38].
The Brazilian standard ABNT NBR 6136 [22] defines the requirements for hollow concrete masonry blocks.For non-structural concrete blocks, a compressive strength higher than 3 MPa must be reached in blocks when normal-density aggregate is used.In this current research work, the compressive strength was assessed on typical cylindrical specimens since concrete mix designs are the focus of this study.With some limitations, one can say that GP10 and GP20 concrete did not pass the test.It must also be noted that the vibro compression applied in the laboratory (explained in Section 3.3.1)may not exactly represent the industrial-scale process.
Figure 13 shows Young's modulus results for the concrete mixtures under study (see Table 3).The result for each concrete mixture corresponded to the average of three specimens.Young's modulus varied between 6.7 and 9.7 GPa, a narrow range compared to compressive strength.The highest Young's modulus result was obtained for reference concrete mixture (CTL), followed by GP10QP10.
The Brazilian standard ABNT NBR 6136 [22] defines the requirements for hollow concrete masonry blocks.For non-structural concrete blocks, a compressive strength higher than 3 MPa must be reached in blocks when normal-density aggregate is used.In this current research work, the compressive strength was assessed on typical cylindrical specimens since concrete mix designs are the focus of this study.With some limitations, one can say that GP10 and GP20 concrete did not pass the test.It must also be noted that the vibro compression applied in the laboratory (explained in Section 3.3.1)may not exactly represent the industrial-scale process.
Figure 13 shows Young's modulus results for the concrete mixtures under study (see Table 3).The result for each concrete mixture corresponded to the average of three specimens.Young's modulus varied between 6.7 and 9.7 GPa, a narrow range compared to compressive strength.The highest Young's modulus result was obtained for reference concrete mixture (CTL), followed by GP10QP10.

Water Absorption by Immersion
The water absorption test results are presented in Table 4, and each result corresponds to the average of three concrete specimens for each concrete mix shown in Table 3.Besides water absorption (A), other measures can be calculated, namely, void index (Iv), specific mass of the dry sample (ρs), and the saturated sample (ρsat) (as explained in Section 3.3.4),which are also presented in Table 4.In this case, the lower the results, the better the concrete resistance to water.The results varied between 8.92% and 17.90%, and the lowest absorption was obtained by GP20 concrete specimens.According to the Brazilian standard ABNT NBR 6136 [22], hollow concrete blocks for concrete masonry must present an absorption lower than 11% when normal-density aggregates are used.In this case, since cylindrical concrete specimens were used, the authors followed the procedure of NBR 9778 [38].However, with some precautions, it can be perceived that GP10 and GP20QP10 concrete absorption values were higher than 11%.Surprisingly, GP20 reached the lowest absorption with a value of 8.90%.

Water Absorption by Immersion
The water absorption test results are presented in Table 4, and each result corresponds to the average of three concrete specimens for each concrete mix shown in Table 3.Besides water absorption (A), other measures can be calculated, namely, void index (Iv), specific mass of the dry sample (ρs), and the saturated sample (ρsat) (as explained in Section 3.3.4),which are also presented in Table 4.In this case, the lower the results, the better the concrete resistance to water.The results varied between 8.92% and 17.90%, and the lowest absorption was obtained by GP20 concrete specimens.According to the Brazilian standard ABNT NBR 6136 [22], hollow concrete blocks for concrete masonry must present an absorption lower than 11% when normal-density aggregates are used.In this case, since cylindrical concrete specimens were used, the authors followed the procedure of NBR 9778 [38].However, with some precautions, it can be perceived that GP10 and GP20QP10 concrete absorption values were higher than 11%.Surprisingly, GP20 reached the lowest absorption with a value of 8.90%.

UPV and Electrical Resistivity
Non-destructive testing techniques, particularly the UPV, are usually employed to evaluate the quality of a concrete structure since they enable such examination without damaging it.UPV can assess the homogeneity of concrete and properties that change with time [49].Figure 14 depicts the UPV from 7 to 28 days for the concrete specimens of the mixtures under study (see Table 3).Each UPV value for each age corresponded to the average of six specimens.As can be perceived, the UPV did not change significantly, except for CTL concrete, in which a significant increase was observed from 7 to 14 days, as well as for GP10 concrete specimens.The UPV presented a narrow range of variation among all the concrete mixtures under study, around 2-2.5 km/s at 28 days.

UPV and Electrical Resistivity
Non-destructive testing techniques, particularly the UPV, are usually employed to evaluate the quality of a concrete structure since they enable such examination without damaging it.UPV can assess the homogeneity of concrete and properties that change with time [49].Figure 14 depicts the UPV from 7 to 28 days for the concrete specimens of the mixtures under study (see Table 3).Each UPV value for each age corresponded to the average of six specimens.As can be perceived, the UPV did not change significantly, except for CTL concrete, in which a significant increase was observed from 7 to 14 days, as well as for GP10 concrete specimens.The UPV presented a narrow range of variation among all the concrete mixtures under study, around 2-2.5 km/s at 28 days.Electrical resistivity can be an empirical indicator of cement-based material durability [11,27,50].Since it depends on the pore structure, such as porosity and pore connectivity, as well as pore solution conductivity, electrical resistivity provides valuable information regarding the microstructure and hydration process of cementitious materials [50][51][52].Figure 15 shows the electrical resistivity results concerning the concrete mixtures under study between 7 and 28 days.At an early age, 7 days, the resistivity reached values between 5000 and 12,000 ohms.Afterwards, a substantial increase for all concrete types occured, reaching 20,000 and 25,000 ohmmeters at 28 days.This translates as an increase of about 400%. Figure 15 also proposes that the resistivity of all concrete mixtures would continue to increase beyond 28 days.This indicates that the hydration reaction was still undergoing due to the high w/c, which allowed for a continuous hydration reaction.Electrical resistivity can be an empirical indicator of cement-based material durability [11,27,50].Since it depends on the pore structure, such as porosity and pore connectivity, as well as pore solution conductivity, electrical resistivity provides valuable information regarding the microstructure and hydration process of cementitious materials [50][51][52].Figure 15 shows the electrical resistivity results concerning the concrete mixtures under study between 7 and 28 days.At an early age, 7 days, the resistivity reached values between 5000 and 12,000 ohms.Afterwards, a substantial increase for all concrete types occured, reaching 20,000 and 25,000 ohmmeters at 28 days.This translates as an increase of about 400%. Figure 15 also proposes that the resistivity of all concrete mixtures would continue to increase beyond 28 days.This indicates that the hydration reaction was still undergoing due to the high w/c, which allowed for a continuous hydration reaction.It must be noted that before the non-destructive test, the mass of each specimen was recorded to ensure that UPV and resistivity did not translate to drying.No mass loss was observed (below 1%).It must be noted that before the non-destructive test, the mass of each specimen was recorded to ensure that UPV and resistivity did not translate to drying.No mass loss was observed (below 1%).

Main Results Summary and Material Efficiency
Table 5 shows the main results obtained from the tests conducted in this work.Note that the variation was very low for the six concrete formulations under study for both electrical resistivity and ultrasonic pulse velocity, indicating a positive result.On the other hand, the results of the water absorption test varied considerably.The best value obtained and within the standard was for the GP20 composition, with 8.90% absorption, while the others did not reach the limit.As for compression, the individual substitutions resulted in low values compared to the reference concrete, which obtained 4.24 MPa, while the highest value obtained was 5.37 MPa for the composition that combined the two substitutions, GP10QP10.It also obtained good results for the modulus of elasticity, with 8.74 MPa, while the reference concrete obtained 9.69 MPa, a difference of less than 10%.Besides engineering properties, global warming potential (GWP) was used as an environmental indicator of designed concrete mixtures on a volumetric basis, i.e., the sum of the embodied carbon of each constituent raw material to produce 1 m 3 of each concrete mixture studied in this current work (see Table 2).The embodied CO 2 for each constituent material used in the current concrete formulations was considered according to Table 5.Since GP and QP are waste materials, GWP allocation was considered zero, as defined in the European Union Directive 2008/98/EC.The embodied CO 2 for all concrete mixtures is also presented in Table 5.As can be seen, the embodied CO 2 was between 91 and 112 kgCO 2 /m 3 .The cement content was the most significant contributor to GWP.As expected, GP20 presented the lowest GWP since the cement content was reduced.The admixture also had significant GWP (see Table 5), even though it was used in lower dosages than the remaining constituent materials.
In addition, the relationship between the GWP (per 1 m 3 ) of each concrete mixture and the compressive strength was investigated, as can be seen in Table 6.For that, the embodied carbon dioxide index (CI) was calculated according to previous research [53][54][55] as follows: CI = GWP KgCO 2 /m 3 Rc, 28d (MPa) The carbon dioxide index (CI) translates the relation between the embodied CO 2 and MPa of strength.As such, the lower the CI, the higher the strength with lower CO 2 emissions.Thus, the best compromise between mechanical performance and ecological balance (at the material level, not considering production or transport costs) corresponds to concrete GP10QP10.

Conclusions
Concrete masonry blocks are used worldwide in large quantities for many applications.As such, the use of industrial waste in their manufacture represents an interesting and sustainable final waste destination, namely if generated in considerable amounts as waste glass powder and quartz powder.This current work studied the application of GP and QP for producing vibro-compressed concrete blocks with non-structural behaviour.Given the results obtained from this research, the following conclusions were drawn:

•
The best combination of cement + water + admixture was studied at the mortar level to obtain zero slump mortars for vibro-compressed concrete.

•
The compressive decreased when GP and QP were used alone; however, when combining 10% GP as a cement replacement +10% QP as a fine aggregate replacement, the compressive strength increased compared to the reference concrete.

•
Concerning water absorption, the results varied between 8.92% and 17.9%, and the lowest absorption was obtained by GP20 concrete specimens.

•
The UPV presents a narrow range of variation among all the concrete mixtures under study, around 2-2.5 km/s at 28 days.

•
By contrast, electrical resistivity was achieved at 28 days, at 20,000 and 25,000 ohmmeters, and it seemed that the resistivity of all concrete mixtures would continue to increase beyond 28 days, which indicates that the hydration reaction was still undergoing.
Even though the other results obtained were within expectations, it is worth mentioning that the casting of the concrete did not completely simulate the manufactured process on an industrial scale since vibration was not carried out simultaneously with compression, which may affect the results.However, the research showed promising results, thus proving the added value of different and abundant local waste for the precast concrete block industry.
Based on the analyses of the results, as a suggestion for future research, it is believed that it would be interesting to test other substitution levels.Moreover, this current work can be integrated with coarse aggregate replacement studies, considering previous research work [23][24][25][26][27].

Figure 3 .
Figure 3. Particle size distribution of solid materials.

Figure 3 .
Figure 3. Particle size distribution of solid materials.

Figure 5 .
Figure 5. Faury reference and real curves obtained for sand and gravel used in the current concrete mix design for "zero slump".

Figure 5 .
Figure 5. Faury reference and real curves obtained for sand and gravel used in the current concrete mix design for "zero slump".

Figure 7 .
Figure 7. Compressive strength test on a concrete specimen.

Figure 6 .
Figure 6.Vibro-compressed concrete specimen producing steps in the laboratory.

Figure 7 .
Figure 7. Compressive strength test on a concrete specimen.

Figure 7 .
Figure 7. Compressive strength test on a concrete specimen.

Figure 8 .
Figure 8. Modulus of elasticity test on a concrete specimen.
(a) Concrete specimens in the oven (b) Concrete specimens in water immersion

Figure 8 .
Figure 8. Modulus of elasticity test on a concrete specimen.
(a) Concrete specimens in the oven (b) Concrete specimens in water immersion

Figure 10 .
Figure 10.UPV test on a concrete specimen.

Figure 10 .
Figure 10.UPV test on a concrete specimen.

Figure 11 .
Figure 11.Electrical resistivity test on a concrete specimen.

Figure 12 .
Figure 12.Compressive strength at 28 days for concrete mixtures.

Figure 11 .
Figure 11.Electrical resistivity test on a concrete specimen.

Figure 11 .
Figure 11.Electrical resistivity test on a concrete specimen.

Figure 12 .
Figure 12.Compressive strength at 28 days for concrete mixtures.

Figure 12 .
Figure 12.Compressive strength at 28 days for concrete mixtures.

Figure 13 .
Figure 13.Young's modulus at 28 days for concrete mixtures.

Figure 13 .
Figure 13.Young's modulus at 28 days for concrete mixtures.

Figure 14 .
Figure 14.UPV evolution from 7 to 28 days for the concrete mixtures under study.

Figure 14 .
Figure 14.UPV evolution from 7 to 28 days for the concrete mixtures under study.

19 Figure 15 .
Figure 15.Electrical resistivity evolution from 7 to 28 days for the concrete mixtures under study.

Figure 15 .
Figure 15.Electrical resistivity evolution from 7 to 28 days for the concrete mixtures under study.

Table 1 .
Main properties of cement, QP, and GP.

Table 1 .
Main properties of cement, QP, and GP.

Table 2 .
Summary of the mortar studied.

Table 2 .
Summary of the mortar studied.

Table 4 .
Water absorption test results for concrete mixtures.

Table 5 .
Summary of the main properties of the concrete studied.

Table 6 .
GWP for each constituent material employed in concrete production.