A Novel Magnetic Nano-Adsorbent Functionalized with Green Tea Extract and Magnesium Oxide to Remove Methylene Blue from Aqueous Solutions: Synthesis, Characterization, and Adsorption Behavior

: In this study, a novel green tea/Mg-functionalized magnetic nano-adsorbent, denoted as GTE-MgO-Fe 3 O 4 NPs, was developed and applied to the extraction of Methylene Blue (MB) from water-based solutions. The GTE-MgO-Fe 3 O 4 NPs were synthesized by incorporating green tea extracts (GTE) and Mg species onto the surface of Fe 3 O 4 nanoparticles using a hydrothermal method. Characterization analyses corroborated the successful functionalization of the Fe 3 O 4 surface with GTE and Mg species, resulting in a superparamagnetic adsorbent equipped with abundant surface functional groups, which promoted MB adsorption and facilitated magnetic separation. Batch experiments revealed that different operating parameters had an impact on the adsorption behavior, such as adsorbent dosage, pH, coexisting ions, contact time, the initial MB concentration, and temperature. The investigations of adsorption kinetics and isotherms emphasized that the MB adsorption onto GTE-MgO-Fe 3 O 4 NPs was an exothermic process dominated by chemisorption. The experimental adsorption capacity of GTE-MgO-Fe 3 O 4 NPs for MB surpassed 174.93 mg g − 1 , markedly superior to the performance of numerous other adsorbents. Ultimately, the utilized GTE-MgO-Fe 3 O 4 NPs could be effectively regenerated through acid pickling, retaining over 76% of its original adsorption capacity after six adsorption–desorption cycles, which suggested that GTE-MgO-Fe 3 O 4 NPs was a suitable adsorbent for eliminating MB from effluent.


Introduction
The escalating discharge of dye-containing effluents into water bodies via human activities, including leather tanning, printing, and textile production, has turned the decontamination of dye-polluted water into an urgent global challenge [1,2].For instance, during the dyeing process in the textile industry, 2-15% of the used dyes are lost in the effluent, which not only contributes to unacceptable water pollution but also poses a significant hazard to aquatic life, even to humans [3,4].A common cationic dye employed in fabric valorization processes is methylene blue (MB).In humans and animals, excessive exposure to MB can cause a number of illnesses, including allergies, gastrointestinal disorders, diarrhea and nausea, tachycardia, and respiratory distress [5].To comply with the associated health and environmental concerns, numerous effective and eco-friendly approaches, such as electrochemical treatment, flocculation, membrane separation, and adsorption, have been imperatively developed to eliminate the water contamination caused by dyes [6].Among these processes, the adsorption process is favored for its ease of operation, high efficiency at low energy consumption, and robustness to variations in water quality [7].
Magnetochemistry 2024, 10, 31 2 of 15 A multitude of adsorbents have been developed in the interim to absorb cationic dyes.Owing to its unique physicochemical properties (e.g., well-developed porous structures and rich functional groups on the surface), biomass is considered a promising class of porous adsorbents with a high capability of removing a variety of organic and inorganic pollutants from water [8].Among biomass, green tea has garnered interest as an inexpensive and readily accessible adsorbent material.It was discovered that green tea performs well when it comes to dye adsorption.The biological components of tea leaves can encapsulate and shield the adsorbent, increasing its stability in an aqueous environment.Furthermore, the uniform encirclement of the biological matrix around the adsorbent allows for the augmentation of its surface pore count, while sufficient pore filling can also improve the adsorption efficiency of MB.
However, the application of raw biomass without modifications is still restricted in practical water treatment due to its non-optimal pore sizes, which results in a relatively poor adsorption capacity, necessitating an excessive dosage of adsorbent to achieve the desired level of contaminant removal [9].Additionally, achieving both high uptake and a high adsorption rate simultaneously for larger molecules or ions is still challenging with most raw biomass due to the low accessibility of porous surfaces and the large diffusion distance within the unimodal pores [6].To address these issues, various physical and chemical modifications of impregnating nano-sized metal oxide (e.g., Mg, Mn, Al, Fe, etc.) into raw biomass have been developed to reduce the diffusion path lengths and provide easier access to the porous regions by varying the surface properties and pore structure, thereby improving the adsorption efficiency and reducing the amount of adsorbent required for effective water treatment [10].For instance, the loading of nontoxic MgO nanoparticles into biomass through a chemical pretreatment process can significantly enlarge the adsorbent's porosity and increase the number of available binding sites, which results in a superior adsorption capacity toward dye, surpassing that of the raw biomass and even other commercially available adsorbents [10,11].Despite the promoted adsorption capability of the MgO-modified biomass, the challenge of recycling the used adsorbent from solutions remains unresolved, which limits the widespread application of MgO-modified biomass adsorbents in wastewater treatment.
As a solution, incorporating a magnetic core into the adsorbent can achieve effective and fast separation and collection using an external magnetic field [12].Magnetite (Fe 3 O 4 ) nanoparticles are commonly used as the magnetic core for the preparation of various magnetic adsorbents because of their typical superparamagnetic behavior, high stability, affordability, and low toxicity [13].Cai et al. [14] prepared Fe 3 O 4 @Ti-SiO 2 (FTS), a new magnetic adsorbent with superior pore volume, specific surface area, thermal stability, and surface charge.Fe 3 O 4 nanoparticles worked in concert to enhance the adsorbent's ability to selectively adsorb cationic dyes from complex wastewater, leading to a maximum adsorption capacity of 336.74 mg g −1 for MB.Hinsene et al. effectively synthesized a ternary recyclable rice husk biochar (Fe 3 O 4 -ZnO/RBC-DES), which was a biopolymerbased magnetic nanocomposites doped with Fe 3 O 4 -ZnO nanoparticles and deep eutectic solvents [15].The nano-adsorbent surface was modified with more potent active adsorption sites.Furthermore, the incorporation of the metal oxide nanocomposites (i.e., Fe 3 O 4 -ZnO) significantly facilitated the removal of contaminants.Inspired by the advantages of Fe 3 O 4 nanoparticles, integrating them into MgO-modified biomass is expected to enhance the dye adsorption capacity and facilitate the easy separation of the used adsorbent along with the adsorbed dye from water through the application of an external magnetic field.
In this study, a magnetic MgO-modified biomass adsorbent, named GTE-MgO-Fe 3 O 4 NPs, is synthesized using green tea, MgO, and Fe 3 O 4 nanoparticles.Methylene blue is chosen as a typical dye with a large heterocyclic aromatic structure to assess the adsorption capacity of the prepared GTE-MgO-Fe 3 O 4 NPs [13].Characterization analysis is carried out to thoroughly investigate the physicochemical properties of GTE-MgO-Fe 3 O 4 NPs.Subsequently, the mechanisms underlying the MB adsorption are clarified, and the effects of different operational parameters, including adsorbent dosage, reaction pH, coexisting ions, contact time, and temperature, on the process of adsorption, are assessed through a series of kinetic, isotherm, and thermodynamic experiments.Lastly, studies utilizing desorption-adsorption cycles were conducted to evaluate the capacity of GTE-MgO-Fe 3 O 4 NPs for regeneration and recovery.

Chemicals and Reagents
Dried green tea leaves, sourced from the Chongqing Yongchuan District Tea Industry Association, were finely pulverized using a high-speed blender and then stored in a refrigerator maintained at a temperature of 277.15K before utilization.Chemicals and reagents, including nanoiron tetraoxide, methylene blue, magnesium sulfate, sodium acetate, anhydrous ethanol, sodium hydroxide, hydrochloric acid, sodium chloride, potassium chloride, calcium chloride, sodium nitrate, and sodium sulfate, etc., were analytically pure and utilized exactly as supplied.Unless specified otherwise, all solutions were made with deionized water (DI-water, 18.2 MΩ cm) from a Taisite water purification system.

Adsorbent Preparation
Green tea extracts (GTE) preparation: 80 g of pulverized green tea leaves were ultrasonically dispersed into 100 mL DI water, and then the above mixture was transferred into a beaker with a cover (500 mL).The above mixture was heated at 353 K for 1 h and then filtered (0.45 mm) to obtain the green filtrate.The obtained GTE was transferred to a brown bottle and stored in the refrigerator (277.15K).
GTE-MgO-Fe 3 O 4 NP preparation: 10 g CH 3 COONa and 3 g MgSO 4 7H 2 O were ultrasonically dissolved in 20 mL DI water.Subsequently, the above solution was introduced dropwise into a 200 mL three-necked flask that already contained 0.9 g of commercial Fe 3 O 4 nanoparticles (particle size 50-100 nm) and 80 mL of GTE solution.The above mixture within the flask was then subjected to vigorous stirring (300 rpm) and heated at 353.15 K for 3 h.Once cooled to room temperature, the solids in suspension were magnetically separated and subsequently washed three times with ethanol and DI water.After washing, the solids were dried in a vacuum oven for a duration of 24 h at 353.15 K.The final product was a black adsorbent material designated as GTE-MgO-Fe 3 O 4 NPs.

Batch Adsorption Experiments
To investigate the adsorption kinetics, formulate adsorption isotherms, and evaluate the adsorption capacity of MB onto GTE-MgO-Fe 3 O 4 NPs, batch adsorption experiments were conducted.Briefly, a stock solution of MB was created by dissolving MB powders directly in DI water, which was then diluted to achieve predetermined concentrations prior to the reactions.The pH of the solution was brought to the necessary level by adding 0.2 M H 2 SO 4 and 0.2 M NaOH solutions.Then, 0.15 g L −1 of GTE-MgO-Fe 3 O 4 NPs was added to 50 mL of each solution with the intended MB concentration.The reaction vessels were placed on an orbital shaking incubator set at 400 rpm and agitated for 180 min at a steady temperature.At specified intervals, aliquots were collected, immediately filtered using a 0.22 µm filter, and subsequently neutralized with 1 mL of a 40 mM phosphate buffer solution (pH 6) before undergoing analysis.All experiments were repeated three times.
Residual MB concentrations in the samples were quantified by measuring the absorbance at a wavelength of 664 nm using a UV-vis spectrophotometer (TU-1901, provided by Shanghai Jinghong Experimental Equipment Co., Shanghai, China).To assess the effect of pH on adsorption efficiency, the pH was adjusted within a wide range of 1 to 11 using 0.2 M H 2 SO 4 and 0.2 M NaOH solutions.Additionally, the influence of commonly co-existing ions on adsorption performance was evaluated by introducing various concentrations (0.1 to 200 mM) of Na + , K + , Ca 2+ , Cl − , NO 3 − , and SO 4 2− into the reaction mixture.The adsorption capacity (q e ) was determined by utilizing the following Equation (1).
where C 0 and C e are the initial and equilibrium MB concentrations in solution, respectively; M is the mass of the adsorbent; and V is the volume of the reaction solution.
To gain a deeper understanding of the adsorption kinetics, the Pseudo-First-Order (PFO), Pseudo-Second-Order (PSO), and Intra-Particle Diffusion models were utilized to analyze the experimental kinetic data.For the adsorption isotherm experiments, the adsorbent dosage was fixed at 0.3 g L −1 , and the MB concentration spanned from 20 to 100 mg L −1 .The above reaction solution was shaken (at 400 rpm) at a constant temperature of 288.15, 298.15, 308.15, and 318.15K for 20 h, respectively.For a more comprehensive understanding of the adsorption behavior, the Langmuir, Freundlich, and Temkin isotherm models were applied to analyze the experimental adsorption data.The related equations and parameters are expressed in Table 1.
Table 1.Kinetic and equilibrium isotherm models.

Models Expression
PFO q t = q e 1 − e −k 1 t PSO q t = q e k 2 2 t 1+k 2 q e t Intra-Particle Diffusion Temkin q e = RT b T lnC e + RT b T ln f Where q t (mg g −1 ) and q e (mg g −1 ) are the amount of MB adsorbed on GTE-MgO-Fe 3 O 4 NPs at any time t (min) and equilibrium, respectively; k 1 (min −1 ), k 2 (g mg −1 min −1 ), and k 3 (g mg −1 min −0.5 ) are the rate constants for the PFO, PSO, and Intra-Particle Diffusion models, respectively; C (mg g −1 ) is the model constant for the boundary layer thickness.q m (mg g −1 ) is the maximum adsorption of GTE-MgO-Fe 3 O 4 NPs; C e (mg L −1 ) is the concentration of residual MB in solution at equilibrium; k L (L mg −1 ), k F (mg g −1 ), and b T (J mol −1 ) are the constants for the Langmuir, Freundlich, and Temkin models, respectively; n is the Freundlich heterogeneity factor; and f (L mg −1 ) is the maximum binding energy constant for the Temkin model.

Characterization of GTE-MgO-Fe 3 O 4 NPs
The SEM image of GTE-MgO-Fe 3 O 4 NP particles, as depicted in Figure 1a, revealed the highly uniform distribution of spherical particles without significantly aggregating into large clusters.The particle size of GTE-MgO-Fe 3 O 4 NP particles was approximately 50-100 nm.The possible surface modification with GTE and Mg resulted in the rough surface of the absorbent (Figure 1b), which likely increased the specific surface area (S BET ) and supplied more active sites for MB adsorption.The EDS image (Figure 1c), along with the corresponding element signals, displayed the highly uniform distribution of C, O, Mg, and Fe elements, which implied the successful loading of GTE and MgO onto the surface of Fe 3 O 4 .

Characterization of GTE-MgO-Fe3O4 NPs
The SEM image of GTE-MgO-Fe3O4 NP particles, as depicted in Figure 1a, revealed the highly uniform distribution of spherical particles without significantly aggregating into large clusters.The particle size of GTE-MgO-Fe3O4 NP particles was approximately 50-100 nm.The possible surface modification with GTE and Mg resulted in the rough surface of the absorbent (Figure 1b), which likely increased the specific surface area (SBET) and supplied more active sites for MB adsorption.The EDS image (Figure 1c), along with the corresponding element signals, displayed the highly uniform distribution of C, O, Mg, and Fe elements, which implied the successful loading of GTE and MgO onto the surface of Fe3O4.Based on the N2 adsorption-desorption isotherm depicted (Figure 2a), the prepared GTE-MgO-Fe3O4 NPs had an SBET of 36.54 m 2 g −1 with an average pore diameter of 10.18 nm.Besides, the bimodal pore size distribution with the predominant pore sizes at around 2.32 and 68.40 nm suggested a complex porous structure that could facilitate efficient adsorption by providing a variety of sites for MB to bind.The crystallinity of the GTE-MgO-Fe3O4 NPs surface was characterized by XRD (Figure 2b).The sharp and intense diffraction peaks represented crystallographic planes (111), ( 220), ( 311), ( 222), (400), ( 422), ( 511), (440), and (533), which were well indexed to the crystal structure of Based on the N 2 adsorption-desorption isotherm depicted (Figure 2a), the prepared GTE-MgO-Fe 3 O 4 NPs had an S BET of 36.54 m 2 g −1 with an average pore diameter of 10.18 nm.Besides, the bimodal pore size distribution with the predominant pore sizes at around 2.32 and 68.40 nm suggested a complex porous structure that could facilitate efficient adsorption by providing a variety of sites for MB to bind.The crystallinity of the GTE-MgO-Fe 3 O 4 NPs surface was characterized by XRD (Figure 2b).The sharp and intense diffraction peaks represented crystallographic planes (111), ( 220), (311), ( 222), (400), ( 422), ( 511), (440), and (533), which were well indexed to the crystal structure of Fe 3 O 4 (JCPDS PDF No. 19-0629) [16], indicating that the GTE-MgO-Fe 3 O 4 NPs was possibly endowed with magnetic properties.Furthermore, the presence of Mg1s and Fe2p peaks in the XPS (Figure S1) suggests that MgO and Fe 3 O 4 have been partially bonded to the adsorbent.Notably, no obvious diffraction peaks belonging to organic copolymers and Mg species emerged, which suggested the low content or highly amorphous state of these additives on the GTE-MgO-Fe 3 O 4 NPs surface [17].Compared with GTE, the peaks assigned to the oxygen-associated functional groups in the range of 940-1750 cm −1 obviously shifted in GTE-MgO-Fe 3 O 4 NPs (Figure 2c) [18].For instance, the peaks corresponding to C−O (1641 cm −1 ) and C=C/C=O bonds (1052 cm −1 ) moved to 1619 and 1096 cm −1 , respectively [19,20].This shift illustrates the complexation reaction that occurs between metal species (such as Fe and Mg) and the oxygen-containing functional groups present in GTE [21].The novel peak observed at 3146 cm −1 was attributed to the stretching vibration of O−H linked to metal elements, specifically Mg and Fe [22].The new adsorption detected at 578 cm −1 was related to the stretching vibration of metal-oxygen bonds in Mg−O or Fe−O complexes [23,24], confirming that the Fe/Mg species complexed with the functional groups of GTE by sharing an oxygen atom [25], which resulted in the formation of chelate bonds or bidentate bridge coordination bonds [26].Magnetic field-dependent behavior of GTE-MgO-Fe 3 O 4 NPs was measured by VSM, and the result (Figure 2d) revealed a narrow S-shaped hysteresis loop with negligible remanence and coercivity, exhibiting the distinctive features of magnetic Fe 3 O 4 .Thus, although the modification with GTE and MgO likely varied the structure of Fe 3 O 4 , GTE-MgO-Fe 3 O 4 NPs still possessed a superparamagnetic characteristic with a high saturation magnetization intensity of 78.16 emu g −1 , which assisted its effective dispersion in the aqueous solution to adsorb MB and also facilitated its magnetic separation under an external magnetic field.Furthermore, the point of zero charge (pH pzc ) of GTE-MgO-Fe 3 O 4 NPs determined from the zeta potential curve in the pH range of 1 to 11 was ~1.65 (Figure S2, being much lower than that of Fe 3 O 4 (common pH pzc range of 6-8), which was probably ascribed to the high oxygen-containing group on the GTE-MgO-Fe 3 O 4 NPs surface [27].

Effect of Adsorbent Dosage
The MB adsorption at different dosages of GTE-MgO-Fe3O4 NPs was displayed in Figure 3a.As the quantity of adsorbent was gradually increased to ≥0.3 g L −1 , the removal efficiency rose steadily to exceed 99.8%.This significant enhancement can be attributed to the augmented adsorption sites provided by the elevated amount of adsorbent used.Nevertheless, the adsorption capacity generally dropped when the adsorben dosage increased, suggesting the insufficient utilization of overdosing adsorbent.Given the high removal efficiency and economy, 0.3 g L −1 of GTE-MgO-Fe3O4 NPs was appropriately employed in the following experiments.

Effect of Adsorbent Dosage
The MB adsorption at different dosages of GTE-MgO-Fe 3 O 4 NPs was displayed in Figure 3a.As the quantity of adsorbent was gradually increased to ≥0.3 g L −1 , the removal efficiency rose steadily to exceed 99.8%.This significant enhancement can be attributed to the augmented adsorption sites provided by the elevated amount of adsorbent used.Nevertheless, the adsorption capacity generally dropped when the adsorbent dosage increased, suggesting the insufficient utilization of overdosing adsorbent.Given the high removal efficiency and economy, 0.3 g L −1 of GTE-MgO-Fe 3 O 4 NPs was appropriately employed in the following experiments.

Effect of pH
The solution pH was widely considered a pivotal factor that impacts the adsorption process, primarily because it significantly altered the adsorption-desorption interaction by modifying the surface charge of the adsorbent [28].As presented in Figure 3b, the adsorption capacity increased to reach a plateau with the increment of the initial solution pH from 1 to 11.The hydrolysis of the functional groups (e.g., hydroxyl (-OH) and carboxyl (-COOH)) was highly pH-dependent, resulting in the variation of the adsorbent surface charge in a specific range of pH, which in turn altered the adsorption-desorption interaction [29].When the pH exceeded the point of zero charge (pHpzc), deprotonation of the surface groups took place, resulting in a powerful electrostatic attraction between the negatively charged surface of GTE-MgO-Fe3O4 NPs and the positively charged MB cations.Meanwhile, the enhanced deprotonation of potential active sites (e.g., OH) at higher pH endowed GTE-MgO-Fe3O4 NPs with a strong affinity for MB fixation [17].Conversely, when the pH was less than the point of zero charge (pHpzc), the positively charged surface hindered the adsorption capacity of GTE-MgO-Fe3O4 NPs for MB because of intense electrostatic repulsion.Additionally, under more acidic conditions, the elevated concentration of H + ions in the solution amplified the rivalry between H + and MB for the active sites on the adsorbent's surface, thereby reducing the adsorption capacity as well (33.83mg g −1 at pH 1) [6].Regardless, at a pH of 4 or higher, both the adsorption capacity and removal efficiency exceeded 64 mg g −1 and 98%, respectively.This suggests that GTE-MgO-Fe3O4 NPs hold promise for the broad application of MB removal across a wide pH range.

Effect of Coexisting Ions
The influence of coexisting ions on the MB adsorption by GTE-MgO-Fe3O4 NPs was also evaluated by adding coexisting cations (i.e., Na + , K + , and Ca 2+ ) and anions (i.e., Cl − ,

Effect of pH
The solution pH was widely considered a pivotal factor that impacts the adsorption process, primarily because it significantly altered the adsorption-desorption interaction by modifying the surface charge of the adsorbent [28].As presented in Figure 3b, the adsorption capacity increased to reach a plateau with the increment of the initial solution pH from 1 to 11.The hydrolysis of the functional groups (e.g., hydroxyl (-OH) and carboxyl (-COOH)) was highly pH-dependent, resulting in the variation of the adsorbent surface charge in a specific range of pH, which in turn altered the adsorption-desorption interaction [29].When the pH exceeded the point of zero charge (pH pzc ), deprotonation of the surface groups took place, resulting in a powerful electrostatic attraction between the negatively charged surface of GTE-MgO-Fe 3 O 4 NPs and the positively charged MB cations.Meanwhile, the enhanced deprotonation of potential active sites (e.g., OH) at higher pH endowed GTE-MgO-Fe 3 O 4 NPs with a strong affinity for MB fixation [17].Conversely, when the pH was less than the point of zero charge (pH pzc ), the positively charged surface hindered the adsorption capacity of GTE-MgO-Fe 3 O 4 NPs for MB because of intense electrostatic repulsion.Additionally, under more acidic conditions, the elevated concentration of H + ions in the solution amplified the rivalry between H + and MB for the active sites on the adsorbent's surface, thereby reducing the adsorption capacity as well (33.83mg g −1 at pH 1) [6].Regardless, at a pH of 4 or higher, both the adsorption capacity and removal efficiency exceeded 64 mg g −1 and 98%, respectively.This suggests that GTE-MgO-Fe 3 O 4 NPs hold promise for the broad application of MB removal across a wide pH range.

Effect of Coexisting Ions
The influence of coexisting ions on the MB adsorption by GTE-MgO-Fe 3 O 4 NPs was also evaluated by adding coexisting cations (i.e., Na + , K + , and Ca 2+ ) and anions (i.e., Cl − , NO 3 − , and SO 4 2− ).Among these ions (Figure 3c,d), the positively charged cations seemed to be more adverse to the MB adsorption compared with the negatively charged anions.This difference might be explained by the fact that cations and MB competitively occupy similar sporting sites [30].It has been reported that high ionic strength could significantly disrupt physisorption or the formation of outer-sphere complexes because the increased ions in solution competed for adsorption sites on the surface and screened the electrostatic interactions between the adsorbent and adsorbate.However, the adsorption capacity just decreased to >50 mg g −1 even in the presence of 0.1 to 200 mM Na + and Cl − ions, which implied that the adsorption process encompassed not just weaker physical interactions (physisorption) but also stronger chemical bonding between the adsorbate and the adsorbent, referred to as chemisorption [3].

Effect of Contact Time and Initial MB Concentration: Adsorption Kinetics
The kinetics curve for the MB adsorption on the GTE-MgO-Fe 3 O 4 NPs over time at various initial MB concentrations (10-60 mg L −1 ) was investigated, and results were presented in Figure 4a.GTE-MgO-Fe 3 O 4 NPs exhibited an effective and rapid MB removal capability, resulting in less than 1.0% of MB remaining in the processed solution within a 180-minute timeframe, provided that the initial MB concentration was ≤20 mg L −1 .With the increment of MB concentration to ≥40 mg L −1 , the removal efficiency dropped to a certain extent, which indicated that the fixed dosage of GTE-MgO-Fe 3 O 4 NPs at 0.3 g L −1 could not supply enough adsorption sites for the removal of too high-concentrated MB (e.g., ≥40 mg L −1 ).Notably, the MB adsorption operated rapidly in the first 5 min of contact time because of the abundance of unused binding sites, achieving about 60% of the maximum adsorption capacity.Subsequently, the MB adsorption gradually slowed down with prolonged contact time and eventually reached adsorption equilibrium at ≥150 min of contact time.The observed slowdown stage could be explained by (i) the gradual drop in the concentration gradient between the solution and adsorbent or (ii) the ongoing surface available adsorption site saturation, which most likely causes the repulsive forces among the adsorbed MB [31].Moreover, to delineate the adsorption kinetics, the adsorption data was fitted with both the PFO and PSO models (Figure 4b,c) [30].The kinetic parameters derived from these fittings are enumerated in Table S1.In contrast to the PFO model, the PSO model exhibited superior fitting correlation coefficients (R 2 ≥ 0.99).Additionally, the q e values computed using the PSO model aligned more closely with the experimental q e values across all examined initial MB concentrations.Hence, the PSO model provided a more precise description of the adsorption kinetic data than the PFO model.This suggests that the adsorption of MB by GTE-MgO-Fe 3 O 4 NPs might involve physisorption or electron exchange between the adsorbate and the adsorbent [6].Additionally, the rate constant (k 2 ) gradually decreased with the increment of the initial concentration of MB, which might be caused by the stronger mass transfer resistance at higher MB concentrations [32].
To further understand the mechanism and the rate-limited phase of the MB adsorption process by GTE-MgO-Fe 3 O 4 NPs, the Intra-Particle Diffusion model was chosen to fit the adsorption kinetic data.As seen in Figure 4d, the MB adsorption process at all tested initial MB concentrations could be linearly fitted to three different stages.The first stage (external mass transfer) was the rate-controlling step with the rapid adsorption of MB from the bulk solution to the adsorbent surface, leading to the saturation of GTE-MgO-Fe 3 O 4 NPs surface adsorption sites, which was associated with boundary diffusion [33].Then, the rapid adsorption of MB on the adsorbent surface expanded the diffusion barrier, resulting in a slow intra-particle diffusion stage [30].Subsequently, the following MB adsorption was strongly limited by the pronounced mass transfer resistance and the boundary layer effects, which further curtailed the diffusion of MB into the internal pores of GTE-MgO-Fe 3 O 4 NPs [29].Moreover, none of the fitting curves intersected the origin of the coordinate system, indicating that the adsorption behavior was not solely governed by intra-particle diffusion.Besides, it was probably influenced by both liquid film diffusion and surface adsorption mechanisms [34].Furthermore, as the initial MB concentration increased, the diffusion rate constants for both the first and second stages augmented, suggesting that the interaction between the adsorbent and adsorbate intensifies at elevated MB concentrations due to a powerful mass transfer driving force.Similarly, the rate constant for the adsorption equilibrium phase rose with an increase in the initial MB concentration, signifying that a longer contact duration was necessary to attain adsorption equilibrium at higher MB concentrations.
film diffusion and surface adsorption mechanisms [34].Furthermore, as the initial MB concentration increased, the diffusion rate constants for both the first and second stages augmented, suggesting that the interaction between the adsorbent and adsorbate intensifies at elevated MB concentrations due to a powerful mass transfer driving force.Similarly, the rate constant for the adsorption equilibrium phase rose with an increase in the initial MB concentration, signifying that a longer contact duration was necessary to attain adsorption equilibrium at higher MB concentrations.

Effect of Initial MB Concentration and Temperature: Adsorption Isotherms
The adsorption behavior of MB (10-100 mg L −1 ) on GTE-MgO-Fe3O4 NPs at four different reaction temperatures (288.15,298.15, 308.15, and 318.15 K) was explored.The adsorption capacity rose at all tested temperatures, as illustrated in Figure 3a, in response to an increase in initial MB concentrations.This phenomenon may be explained by a larger concentration gradient between the adsorbent and bulk solution at higher MB concentrations, which increases MB mass transfer at the liquid-solid interface [9].At the peak initial MB concentration (100 mg L −1 ), the experimental adsorption capacity recorded at 288.15 K stood at 174.93 mg g −1 .Nevertheless, as the reaction temperature rose from 298.15 to 318.15 K, the adsorption capacity diminished.For example, at the peak initial MB concentration (100 mg L −1 ), the experimental adsorption capacity recorded at 288.15 K stood at 174.93 mg g −1 .However, this progressively fell to 160.75 mg g −1 at 298.15 K, 154.79 mg g −1 at 308.15 K, and 144.59 mg g −1 at 318.15 K, respectively.
In order to gain additional insight into the behavior of adsorption, three isotherm models, including the Langmuir, Freundlich, and Temkin models, were fitted to the experimental adsorption data at various reaction temperatures (Table 1).The fitting curves were presented in Figure 5a-c, and the related isotherm parameters were listed in Table

Effect of Initial MB Concentration and Temperature: Adsorption Isotherms
The adsorption behavior of MB (10-100 mg L −1 ) on GTE-MgO-Fe 3 O 4 NPs at four different reaction temperatures (288.15,298.15, 308.15, and 318.15 K) was explored.The adsorption capacity rose at all tested temperatures, as illustrated in Figure 3a, in response to an increase in initial MB concentrations.This phenomenon may be explained by a larger concentration gradient between the adsorbent and bulk solution at higher MB concentrations, which increases MB mass transfer at the liquid-solid interface [9].At the peak initial MB concentration (100 mg L −1 ), the experimental adsorption capacity recorded at 288.15 K stood at 174.93 mg g −1 .Nevertheless, as the reaction temperature rose from 298.15 to 318.15 K, the adsorption capacity diminished.For example, at the peak initial MB concentration (100 mg L −1 ), the experimental adsorption capacity recorded at 288.15 K stood at 174.93 mg g −1 .However, this progressively fell to 160.75 mg g −1 at 298.15 K, 154.79 mg g −1 at 308.15 K, and 144.59 mg g −1 at 318.15 K, respectively.
In order to gain additional insight into the behavior of adsorption, three isotherm models, including the Langmuir, Freundlich, and Temkin models, were fitted to the experimental adsorption data at various reaction temperatures (Table 1).The fitting curves were presented in Figure 5a-c, and the related isotherm parameters were listed in Table S2.According to the R 2 values for different isotherm models, the experimental adsorption data at various temperatures were better described by the Freundlich model compared to the Langmuir model, indicative of the multilayer adsorption of MB molecules on the heteroge-neous GTE-MgO-Fe 3 O 4 NPs surface [35].The large amplitude of the Freundlich exponent (n) was often used to assess the degree of favorability of the adsorption process [36].All the obtained n values were in the range of 1-10, evidencing that GTE-MgO-Fe 3 O 4 NPs were favorable and useful for adsorbing MB at various temperatures.Notably, the Temkin model also well described the adsorption data at different temperatures with all R 2 ≥ 0.94, also indicating the multilayer adsorption for MB removal on the GTE-MgO-Fe 3 O 4 NPs surface [30].Further, the heat of adsorption (b T ) obtained from the Temkin model was all > 1 and gradually decreased with the increment of reaction temperature, implying an exothermic process for the MB adsorption by GTE-MgO-Fe 3 O 4 NPs [30].
S2.According to the R 2 values for different isotherm models, the experimental adsorp tion data at various temperatures were better described by the Freundlich model com pared to the Langmuir model, indicative of the multilayer adsorption of MB molecule on the heterogeneous GTE-MgO-Fe3O4 NPs surface [35].The large amplitude of the Freundlich exponent (n) was often used to assess the degree of favorability of the adsorption process [36].All the obtained n values were in the range of 1-10, evidencing that GTE-MgO-Fe3O4 NPs were favorable and useful for adsorbing MB at various tem peratures.Notably, the Temkin model also well described the adsorption data at diffe ent temperatures with all R 2 ≥ 0.94, also indicating the multilayer adsorption for MB r moval on the GTE-MgO-Fe3O4 NPs surface [30].Further, the heat of adsorption (bT) ob tained from the Temkin model was all >1 and gradually decreased with the incremen reaction temperature, implying an exothermic process for the MB adsorption by GTE MgO-Fe3O4 NPs [30].In order to ascertain the spontaneity and character of the adsorption behavior, th Van't Hoff Equation Equations ( 2)-( 4) were used to compute the thermodynamic para eters [30], which comprised Gibbs free energy (ΔG 0 , kJ mol −1 ), enthalpy change (ΔH 0 , k mol −1 ), and entropy change (ΔS 0 , kJ mol −1 ).
where kc (L g −1 ) is the thermodynamic equilibrium constant; C 0 (mol L −1 ) is the standar concentration; Madsorbate is the molecular weight of MB; and γ is the coefficient of activ In order to ascertain the spontaneity and character of the adsorption behavior, the Van't Hoff Equation Equations ( 2)-( 4) were used to compute the thermodynamic parameters [30], which comprised Gibbs free energy (∆G 0 , kJ mol −1 ), enthalpy change (∆H 0 , kJ mol −1 ), and entropy change (∆S 0 , kJ mol −1 ).
where k c (L g −1 ) is the thermodynamic equilibrium constant; C 0 (mol L −1 ) is the standard concentration; M adsorbate is the molecular weight of MB; and γ is the coefficient of activity.The values of ∆G 0 , ∆H 0 , and ∆S 0 (Table S3) were calculated based on the slopes and intercepts derived from the plot of lnk c vs. 1/T (Figure 5d).The negative ∆G 0 values suggested that the adsorption of MB onto GTE-MgO-Fe 3 O 4 NPs is a favorable and spontaneous process.The reduction in the absolute value of ∆G 0 with the up-regulation of reaction temperature indicated that the MB removal by GTE-MgO-Fe 3 O 4 NPs operated through an exothermic adsorption process, which was further supported by the negative ∆H 0 value.This was probably ascribed to the complex interplay between the MB and the assorted surfaces of the adsorption sites [27].Furthermore, the negative ∆S 0 value indicated a reduction in randomness at the solid-liquid interface throughout the adsorption process [30].

Desorption of MB and Recyclability of GTE-MgO-Fe 3 O 4 NPs
As stability and recyclability were the critical factors in assessing the environmental and economic viability of adsorbents, we first adopted three kinds of common eluents, including 0.1 mM HCl, 0.1 mM acetic acid, and anhydrous ethanol, in the desorption experiments, and the desorption efficiency (the ratio of the desorbed MB over the adsorbed MB) is presented in Figure 6a.The desorption efficiencies were found to be 94.3%, 91.7%, and 85.5% for 0.1 mM HCl, 0.1 mM acetic acid, and anhydrous ethanol, respectively, demonstrating that all three eluents were capable of effectively desorbing MB, with 0.1 mM HCl exhibiting the highest efficiency, followed by acetic acid and then anhydrous ethanol.Therefore, all three eluents were further employed in the cycles of the adsorption-desorption process (Figure 6b).Regenerating the used adsorbent with anhydrous ethanol led to a notable reduction in adsorption capacity, which was probably attributed to its relatively inferior efficiency in desorbing chemically bonded MB.Meanwhile, the desorption of MB using acetic acid involved a competitive complexation mechanism, which led to a gradual decline in the number of available adsorption sites as the frequency of desorption cycles increased, consequently resulting in a substantial diminishment of the adsorptive capacity.Since the adsorption capacity dwindled with decreasing pH (Figure 3b), indicating an acidic condition (lower than the pH pzc ) created by 0.1 mM HCl could efficiently desorbed the MB from the used GTE-MgO-Fe 3 O 4 NPs.As shown in Figure 6b, despite a gradual reduction in the MB adsorption capacity of GTE-MgO-Fe 3 O 4 NPs with each adsorption-desorption cycle when using a 0.1 mM HCl solution, the remaining adsorption capacity was more than 48.5 mg g −1 after six cycles, and the adsorption regeneration efficiency was 76.10% when compared to the initial adsorption (the 0th cycle).After six cycles, the adsorption capacities of the other two resolving solutions were slightly lower, at 43.09 mg g −1 for 0.1 mol L −1 CH 3 COOH and 36.82mg g −1 for anhydrous ethanol.These findings indicated the effective separation of GTE-MgO-Fe 3 O 4 NPs without any appreciable loss of adsorbent mass using a magnetic field and demonstrated the ease of reuse with efficient MB removal when employing a 0.1 mM HCl solution as the eluent.

Comparison with the Literature
To assess the performance of Fe 3 O 4 @GT@Mg NPs for the adsorption of MB removal, a comparison was made with other adsorbents that have been reported for the same purpose, including biomass matrix adsorbents, magnetic nanocomposite adsorbents, and biomassbased magnetic nanocomposite adsorbents (Table S4) [37][38][39][40][41][42][43][44].The results illustrated the Fe 3 O 4 @GT@Mg NPs' high removal rate and adsorption capacity, which were generated throughout the current testing.In addition, Fe 3 O 4 @GT@Mg NPs were produced in an environmentally responsible way and exhibited exceptional magnetic separation properties.They may, therefore, considerably reduce the pollution that adsorbents release into the environment both during their manufacture and use.As a result, Fe 3 O 4 @GT@Mg NPs were efficient adsorbents for removing MB from wastewater.

Comparison with the Literature
To assess the performance of Fe3O4@GT@Mg NPs for the adsorption of MB removal, a comparison was made with other adsorbents that have been reported for the same purpose, including biomass matrix adsorbents, magnetic nanocomposite adsorbents, and biomass-based magnetic nanocomposite adsorbents (Table S4) [37][38][39][40][41][42][43][44].The results illustrated the Fe3O4@GT@Mg NPs' high removal rate and adsorption capacity, which were generated throughout the current testing.In addition, Fe3O4@GT@Mg NPs were produced in an environmentally responsible way and exhibited exceptional magnetic separation properties.They may, therefore, considerably reduce the pollution that adsorbents release into the environment both during their manufacture and use.As a result, Fe3O4@GT@Mg NPs were efficient adsorbents for removing MB from wastewater.

Conclusions
In this study, a modified magnetic adsorbent named GTE-MgO-Fe 3 O 4 NPs was successfully fabricated by impregnating GTE and Mg species onto the surface of Fe 3 O 4 nanoparticles.Its efficacy in removing MB from aqueous solutions has been documented.Characterization analyses confirmed that the resultant GTE-MgO-Fe 3 O 4 NPs possessed robust magnetic properties and an abundance of surface functional groups.Batch adsorption experiments illustrated that GTE-MgO-Fe 3 O 4 NPs could effectively adsorb MB over a relatively broad pH range (pH ≥ 4).The MB adsorption behavior exhibited a moderate sensitivity to high ionic strength, implying that both physisorption and chemisorption contributed to the overall adsorption process.Further investigation into the adsorption kinetics and isotherms highlighted chemisorption as the predominant mechanism for MB adsorption by GTE-MgO-Fe 3 O 4 NPs, which was noted for its exothermic characteristics.The adsorption capacity of GTE-MgO-Fe 3 O 4 NPs for MB, as determined experimentally, surpassed 174.93 mg g −1 .This value outweighed the adsorption capacities exhibited by numerous other adsorbents.Moreover, GTE-MgO-Fe 3 O 4 NPs demonstrated exceptional