Supplementary Light with Increased Blue Fraction Accelerates Emergence and Improves Development of the Inﬂorescence in Aechmea , Guzmania and Vriesea

: In protected cultivation, increasing the light level via supplementary lighting (SL) is critical to improve external quality, especially in periods with low light availability. Despite wide applications, the effect of light quality remains understated. In this study, the effect of SL quality and nutrient solution electrical conductivity (EC) on growth and ﬂowering of three bromeliad species was investigated. Treatments included solar light, and this supplemented with R90B10 [90% red (R) and 10% blue (B)], R80B20 (80% R and 20% B), and R70B30 (70% R and 30% B). These were combined with an EC of 1 and 2 dS m -l . Irrespective of the light treatment, the higher EC promoted growth, inﬂorescence emergence, and development in Aechmea fasciata (Lindl.) Baker, whereas adverse effects were noted in Guzmania and Vriesea . The higher EC-induced negative effect in Guzmania and Vriesea was slightly alleviated by SL. With few notable exceptions, SL exerted limited effects on photosynthetic functionality. Depending on the species, SL improved external quality traits. In all species, SL increased root and inﬂorescence weight and stimulated biomass allocation to generative organs. It also accelerated inﬂorescence emergence and promoted inﬂorescence development. In this way, the time to commercial development stage was considerably shortened. These effects were more prominent at R80B20 and R70B30. Under those conditions, for instance, inﬂorescence emergence occurred 3–5 weeks earlier than in the control, depending on the species. In conclusion, SL with increased B proportion leads to shorter production period owing to faster emergence and improved development of the inﬂorescence and is recommended for commercial use. ,


Introduction
Bromeliads (Bromeliaceae) are widely cultivated as ornamental pot plants due to exuberant foliage, peculiar flower characteristics, the potential for year-round flowering, and sustaining bloom for long periods (weeks to months) under interior conditions [1][2][3]. The most commercialized bromeliad species belong to the genera Aechmea, Guzmania, Neoregelia, Tillandsia, and Vriesea. Among them, Guzmania and Vriesea cultivars account for 60 and 15% of annual pot plant sales, respectively [4,5]. In Central and South America, Aechmea species maintain high popularity [2].
In commercial horticulture, uniform and scheduled flowering of bromeliads is conventionally achieved by using ethylene releasing agents, such as acetylene [6,7]. Still, long cultivation is required for the production of flowering bromeliad plants [8]. For instance, the phase between flower induction and anthesis lasts 68 and 114 d for Aechmea fasciata and Vriesea 'splendens,' respectively, with the total cultivation period being 14 and 12 months [9]. Supplementary light is often employed not only to shorten the production period but also to improve the customer-perceived (visual) quality of several ornamental species [10,11]. For instance, a higher light intensity decreased the flower induction period (by 10-70 d) depending on the bromeliad species [12,13]. Moreover, higher light intensity was associated with increased (25%) biomass [14], and improved inflorescence quality (i.e., size and number of florets; [13]). Although the beneficial effect of increased light intensity on the above-mentioned aspects is well-documented, limited attention has been devoted to the role of light quality (spectral distribution). With the development of light-emitting diodes (LEDs), it is now readily feasible to manipulate light quality [15,16]. The interest in using this possibility to promote plant growth and external quality traits is currently expanding [17,18].
Photosynthetic performance is affected by light quality during cultivation [15,16]. Chlorophyll fluorescence is commonly employed for the non-invasive assessment of the electron transport system efficiency [19]. Polyphasic chlorophyll fluorescence induction curves are a novel means of extracting additional information on the photosynthetic apparatus structure and function [17].
Although bromeliads typically require low nutrient solution electrical conductivity (EC; ≈ 1 dS m −1 ), a higher EC (1.5 dS m −1 ) stimulated plant growth in some species. Additionally, plants cultivated under supplemental light often require an enriched nutrient supply [20]. Therefore, changes in light quality may necessitate an adjusted nutrient intake depending on the species of interest.
In order to fully take advantage of the light quality manipulation, as well as to provide guidance for commercial applications in ornamental horticulture, the role of EC alongside light quality was investigated. The objectives of this study were to assess the light regime and EC effects on plant growth, morphology, and biomass partitioning, as well as on flower emergence and development. In addition, chlorophyll fluorescence parameters were obtained by using two protocols to evaluate the impact of the growth regime on photosynthetic performance. To determine whether or not the treatment effects were limited to a specific CO 2 assimilation pathway, species (Aechmea fasciata 'Primera', Guzmania 'Rostara' and Vriesea 'Splenriet') using different types of photosynthesis were employed. The selected species are all equipped with a phytotelm (the so-called tank), which retains water by intercepting precipitation, and in this way, facilitates plant hydration at periods of low soil water availability [21,22].

Plant Material and Growth Conditions
In the present study, Aechmea fasciata 'Primera' (crassulacean acid metabolism; [23,24]), Guzmania 'Rostara' (three carbon photosynthesis; [25]), and Vriesea 'Splenriet' (three carbon photosynthesis; [24]) were employed. Un-rooted transplants were obtained from a commercial nursery (Corn. Bak B.V., Assendelft, the Netherlands). The ones with uniform height (~15 cm) and architecture were selected for potting. For each species, the pot size for commercial purposes was used. This was 8 cm for Guzmania and Vriesea, and 12 cm for Aechmea. Pots were filled with peat moss and perlite mixture (1:3, v/v). Pots were then transferred in a multi-span plastic greenhouse, which was located to Pakdasht (Tehran Province, Iran; 35 • 28 51 N 51 • 41 05 E). Following 4 months of cultivation, plants were fully rooted and treatments were initiated. Treatments lasted between January and September of 2019. Air temperature and relative air humidity were recorded with sensors (Sensohive Technologies ApS, Odense, Denmark) installed in the upper third of the plant canopy. During cultivation, air temperature ranged between 17.5 and 26.5 • C, while relative air humidity between 50 and 76%. The average solar daily light integral was 6.4 ± 0.5 mol m −2 d −1 .
Two factors (4 light regimes × 2 EC levels) were applied in combination. Plants were grown under solar light (non-lighted control), or supplemented with 3 combinations of red (R) and blue (B) light by using LED modules (Guangzhou Grow Light Company Model IGL-158-18R17B7-DC; Input voltage: 220-240 V; 18 W; 0.09 A). These were R90B10 [90% R (peak at 660 nm) and 10% B (peak at 450 nm)], R80B20 (80% R and 20% B), and R70B30 (70% R and 30% B). Supplemental light was provided daily at a photosynthetic photon flux density of 120 µmol m −2 s −1 at the canopy level for 12 h (0800 to 2000 h). In this way, the photoperiod was extended during the intervals of January to April (by 22-165 min), and August to September (by 5 and 47 min, respectively). Light intensity was determined using a PAR-FluorPen device (FP 100-MAX, Photon Systems Instruments, Drasov, Czech Republic), and the spectrum by a SpectroMaster (SEKONIC C-7000, Tokyo, Japan). To avoid light contamination, opaque black-white plastic films were placed around each light regime treatment. To minimize border effects, plants adjacent to these films were not sampled.
Nutrient solution EC was set to 1 or 2 dS m -l (further referred as EC1 and EC2, respectively). The nutrient solution composition for EC1 was based on a commercial source (Corn. Bak B.V., Assendelft, the Netherlands) ( Table 1). For EC2, the concentration of the macro-elements was doubled, maintaining the same ratio as in the original recipe (Table 1). Nutrient solution pH was adjusted to 5.75 [26,27]. Plants were irrigated twice a week [26]. To prevent element accumulation, the substrate was washed with distilled water once per month.
Sampling was conducted at the end of the growth period. Sampled leaves were young, fully-expanded, and grown under direct light. Replicate leaves were collected from separate plants. In all instances, the time between sampling and the start of the evaluation was less than 15 min.

Flower Induction
Six months following the onset of the experiment, flower induction was performed based on commercial practices [26]. Briefly, saturated acetylene solution (18-20 • C) was placed in the tank of the plants. This solution (0.05 dS m −1 EC and pH of 6.9) was prepared by injecting acetylene gas (0.5 bar for 12 min) into 20 L of water. The acetylene treatment was applied in the morning (08:00-10:00 h; 17-19 • C) and repeated a week later.
Two weeks before the first treatment and 4 weeks following the second treatment, nutrient solution supply was ceased [9,12]. To secure flower induction, plants were kept fully irrigated 14 d before the first treatment. Additionally, 3 d before each treatment, irrigation was performed in a way that the tanks were full of water, and the substrate was completely wet. Plants were not irrigated for 2 d after each treatment.

Plant Growth, Morphology, and Biomass Allocation
Nine months following the onset of the experiment, plant growth, morphology, and biomass allocation were determined. Evaluations included plant height (from the root-toshoot junction to the apical inflorescence end), number of offshoots (the so-called pups), crown thickness (1 cm above the root-to-shoot junction), tank volume, number of leaves, and leaf area. For leaf area assessment, leaves were scanned (HP Scanjet G4010, Irvine, CA, USA) and then evaluated by using the Digimizer software (version 4.1.1.0, MedCalc Software, Ostend, Belgium).
Following removal of the substrate from the roots via gentle washing, root volume was measured by employing a volume-displacement technique [28]. Plant roots were suspended in a cylinder filled with water. Root volume was then determined by measuring the volume of water displaced by the plant roots.
Leaf, root, and inflorescence (fresh and dry) masses were also recorded. For measuring dry weight, samples were placed in a forced-air drying oven for 72 h at 80 • C. By using dry mass, specific leaf area (SLA; leaf area/leaf mass), flower mass ratio (FMR; flower mass/plant mass), leaf mass ratio (LMR; leaf mass/plant mass), and root mass ratio (RMR; root mass/plant mass) were calculated. All the measurements were conducted on 4 plants per treatment.

Inflorescence Emergence and Development
In bromeliads, the first sign of inflorescence induction in the tank was considered as the beginning of flowering. Inflorescence development was recorded from induction (induced by the first acetylene treatment) until harvest (≈3 month following induction, and 9 months following the onset of the experiment). Inflorescence development was scored based on the scale (1 to 5) depicted in Figure 1. Evaluations were conducted on 4 plants per treatment.

Leaf Osmotic Potential
To maintain cell turgor pressure, plant response to increased nutrient supply often includes osmotic potential adjustments [29]. On this basis, leaf sap osmotic potential was evaluated. For sap extraction, leaves were divided into small segments and placed along with 2 metal spheres (1 mm diameter) in tubes perforated with 4 holes (0.5 mm diameter). Each tube was then encased in a larger one, and centrifuged (15,000× g) for 15 min. For evaluation, sap extract was collected from the larger tube. Osmolarity was assessed with a vapor pressure osmometer (Osmomat 030, Gonotec GmbH, Berlin, Germany). The unit conversion was performed by using the Van't Hoff equation [osmotic potential (MPa) = − osmolarity (mosmoles kg −1 ) × 2.58 × 10 −3 ].

SPAD Value and Leaf Photosynthetic Pigment Content
Leaf pigment content is affected by the growth environment and has implications for both photosynthetic capacity and pot plant ornamental value [30,31]. In this perspective, the leaf SPAD value and photosynthetic pigment (chlorophyll, carotenoids) content were assessed. Leaves were measured by using a SPAD-502 (Konica Minolta Corp., Solna, Sweden). This instrument provides a non-invasive approximation of leaf chlorophyll content by considering leaf transmittance in red and near-infrared light spectra (650 and 940 nm, respectively; [32]). Three points were recorded per replicate leaf and were further averaged. Three replicate leaves were assessed per treatment.
The same leaves were employed for photosynthetic pigment content. Following fine chopping, portions weighing 0.5 g were homogenized with the addition of 10 mL of 80% acetone. This primary acetone extract was then filtered, and the filtered extract was diluted by adding 2 mL of 80% acetone per mL of extract. Since chlorophyll is light sensitive, extraction took place in a dark room [33]. The obtained extract was subjected to reading on a spectrophotometer (Mapada UV-1800; Shanghai. Mapada Instruments Co., Ltd., Shanghai, China). Total chlorophyll and carotenoid contents were calculated [34]. Four leaves were assessed per treatment.

Chlorophyll Fluorescence Imaging
As a sensitive indicator of plant photosynthetic performance, dark-adapted values of the maximum quantum yield of PSII (F v /F m ) were recorded in detached leaves of each treatment. Measurements were conducted by using a FluorCam FC 1000-H (Photon Systems Instruments, Brno, Czech Republic). Leaves were dark-adapted (≥20 min) prior to evaluation. Then, F v /F m was evaluated by applying a saturated photosynthetic photon flux density of 3900 µmol m −2 s −1 [11,19]. Four leaves were assessed per treatment.

Polyphasic Chlorophyll Fluorescence Transient (OJIP) Evaluation
A polyphasic chlorophyll fluorescence induction curve (O-J-I-P-transient) was obtained in detached leaves of each treatment. By employing the JIP test, the shape changes of the OJIP transient were quantitatively translated to a set of parameters, which relate to the in vivo adaptive behavior of the photosynthetic apparatus (especially PSII) to the growth environment [17]. Measurements were conducted by using a PAR-fluorPen FP 100-MAX (Photon Systems Instruments) following dark adaptation (≥20 min). These were obtained at intervals of 50 µs, as well as of 3, 30, and 300 ms. The employed light intensity (3900 mmol m −2 s −1 photosynthetic photon flux density) was sufficient to generate maximal fluorescence for all treatments. Based on the OJIP protocol-obtained data, the performance index for the photochemical activity (PI ABS ) was calculated [35]. Light curves were also obtained by exposing the leaves to different photosynthetic photon flux densities [0 (darkness), 100, 200, 300, 500, and 1000 µmol m −2 s −1 ]. Four leaves were assessed per treatment.

Experimental Design and Statistical Analysis
A completely randomized split plot design with 2 factors (light regime, EC level) was realized. Since the pot size and growth pattern of the employed species were different, each was analyzed separately. Data analyses were carried out using the SAS statistical software (SAS Institute, Cary, NC, USA). Data were tested for homogeneity of variances (Duncan's test). Subsequently, estimated least significant differences (LSD) of treatment effects were determined (p = 0.05).

Plant Growth, Morphology, and Biomass Allocation
Supplementary light increased plant height in Aechmea and Guzmania (Tables 2 and 3). In the former species the highest plant height was under R80B20 (Table 2), while in the latter plant height became higher as the percentage of B increased (Table 3). Supplementary light generally increased the number of offshoots in Aechmea (Table 2). Supplementary light generally increased crown thickness in Guzmania (Table 3). Supplementary light enhanced tank volume in Guzmania, with R70B30 exerting a considerable effect (Table 3). Higher EC decreased tank volume in Aechmea and Guzmania (Tables 2 and 3). In the absence of supplementary light, higher EC also induced yellow spots on the leaves of Aechmea and Guzmania (data not shown).
Supplementary light decreased SLA (a proxy of leaf thickness) in Guzmania (Table 3), while higher EC decreased SLA in Aechmea (Table 2). Supplementary light increased leaf area in Vriesea, whereas higher EC decreased it (Table 4). Supplementary light increased leaf dry weight in Guzmania and Vriesea (Tables 3 and 4). Higher EC increased leaf dry weight in Aechmea (Table 2) and decreased it in Vriesea (Table 4).
Supplementary light increased root dry weight in all three species (Tables 2-4). Higher EC decreased root dry weight in Guzmania (Table 3) and Vriesea (Table 4).
Supplementary light drastically increased flower dry weight in all three species (Tables 2-4). Higher EC increased flower dry weight in Aechmea (Table 2) and decreased it in Guzmania (Table 3) and Vriesea (Table 4).
Supplementary light considerably increased the fresh mass partitioning to the inflorescences in all three species (Figure 2). R80B20 and R70B30 were generally associated with increased fresh mass partitioning to the inflorescences as compared to R90B10 (Figure 2).

Inflorescence Emergence and Development
Supplementary light decreased the time required for inflorescence emergence (Figure 3). R80B20 and R70B30 were associated with a shorter time for inflorescence emergence as compared to R90B10 (Figure 3). Higher EC increased the time required for inflorescence emergence of Guzmania ( Figure S1).     Table S1. Supplementary light increased inflorescence development (Figure 4). In Aechmea and Guzmania, R80B20 and R70B30 were associated with enhanced inflorescence development as compared to R90B10 (Figure 4). Higher EC promoted inflorescence development in Aechmea, whereas it decreased it in Guzmania and Vriesea ( Figure S2).

Leaf Osmotic Potential
In Aechmea, leaf osmotic potential of plants fed by EC1 and exposed to R80B20 and R70B30 was higher (i.e., less negative) as compared to those fed by EC2 and exposed to supplemental light (Table S2). Higher EC decreased leaf osmotic potential (i.e., more negative) in Guzmania and Vriesea (25.9 and 68.4%, respectively; Tables S3 and S4).

SPAD Value and Leaf Photosynthetic Pigment Content
In Aechmea, the SPAD value was affected by the light regime, with plants grown under R70B30 having the highest value (Table S2). In Guzmania, the SPAD value was affected by both the light and EC regimes, with the highest values noted under R70B30 and EC2 (Table S3). In Vriesea, an interaction between light and EC regimes was apparent, where plants grown under R70B30 had higher SPAD value as compared to other light regimes at EC2 (Table S4).
In Aechmea, leaf chlorophyll and carotenoid contents were affected by both the light and EC regimes (Table S2). Cultivation under R70B30 promoted chlorophyll content, whereas it decreased carotenoid content. Instead, the higher EC decreased (8%) chlorophyll content, and stimulated (37.5%) carotenoid content. In Guzmania and Vriesea, light and EC regimes affected neither chlorophyll nor carotenoid contents (Tables S3 and S4).

Chlorophyll Fluorescence Imaging
In Aechmea, F v /F m was significantly affected by the light regime, and plants cultivated under R90B10 had the lowest value (Table S5; see also Figure 5). In this species, the nonphotochemical quenching (NPQ) and performance index for the photochemical activity (PI ABS ) parameters were not affected by the treatments (Table S5).
In Guzmania, F v /F m was not affected by the treatments (Table S6; see also Figure 5). In this species, NPQ was affected by both the light and EC regimes, with the lowest values noted under R80B20 and EC2 (Table S6). In PI ABS , an interaction between light and EC regimes was apparent, where plants grown under R90B10 at EC2 having the lowest value (Table S6).
In Vriesea, F v /F m was significantly affected by the light regime, and plants cultivated under R90B10 had the lowest value (Table S7; see also Figure 5). In this species, NPQ and PI ABS were not affected by the treatments (Table S7).
In Guzmania, some differences in chlorophyll fluorescence between light quality regimes were apparent, though these were not consistent among measurement light intensities (Table S6). Instead, decreased fluorescence was consistently noted in plants cultivated under higher EC at 100 to 500 µmol m −2 s −1 measurement light intensities (Table S6).
In Vriesea, some differences in chlorophyll fluorescence among light quality treatments were noted, but these were not consistent among measurement light intensities (Table S7).
In Guzmania, some differences in chlorophyll fluorescence between light quality regimes were apparent, though these were not consistent among measurement light intensities (Table S6). Instead, decreased fluorescence was consistently noted in plants cultivated under higher EC at 100 to 500 μmol m −2 s −1 measurement light intensities (Table S6).
In Vriesea, some differences in chlorophyll fluorescence among light quality treatments were noted, but these were not consistent among measurement light intensities (Table S7).

The Optimum EC for Growth Mostly Depends on the Species Rather than on Light Level
In Aechmea, the leaf osmotic potential response to the higher EC depended on the light regime (Table S2). In the absence of supplementary light, for instance, Aechmea leaf osmotic potential did not differ between the two EC levels. In Guzmania and Vriesea, by contrast, the higher EC-induced leaf osmotic potential depression was evident independently of the light regime (Tables S3 and S4). These results might be taken to suggest that the overall effect of higher EC on cell turgor pressure was species dependent.
Despite decreased tank volume, higher EC promoted growth (i.e., leaf and flower dry weight; Table 2), and inflorescence development ( Figure S2) in Aechmea. In this species, increased nitrogen level was earlier associated with enhanced plant growth [36]. Increased urea fertilization also stimulated growth in two other bromeliad species (Tillandsia pohliana, Vriesea philippocoburgii) by balancing the levels of cytokinins and auxins [37]. On the contrary, higher EC decreased growth in Guzmania (tank volume, root, and flower dry weight; Table 3) and Vriesea (leaf area, leaf, root, and flower dry weight; Table 4), and negatively affected inflorescence development ( Figure S2). Therefore, the EC level optimum for growth and flowering is clearly species dependent.
Supplementary light slightly alleviated the high EC induced negative effects in Guzmania and Vriesea. In these species, the higher EC-induced yellow spots on the leaves were only apparent in the absence of supplementary light. Incidence of yellow spots on Guzmania leaves owing to elevated EC and low light intensity were also earlier noted [27]. With this minor exception, the present results provide little support that the optimal EC level depends on the light intensity during cultivation of bromeliads.

Increased Supplementary Light B Fraction Shortens the Time to Commercial Development Stage
Supplementary light promoted external quality aspects depending on the species, including plant height, offshoot number, crown thickness, tank volume, and leaf area (Tables 2-4). In all three species, it increased root dry weight, flower dry weight and fresh mass partitioning to the inflorescences (Tables 2-4 and Figure S1). The positive effect of supplementary light on bromeliad plant growth was earlier reported [14,26]. For the first time, this study indicates that both flower dry weight and fresh mass partitioning to the inflorescences were generally enhanced when the proportion of B light in the spectrum was increased (R80B20 and R70B30 as compared to R90B10; Tables 2-4 and Figure S1). Therefore, supplementary light quality is a critical determinant of ornamental value, with enhanced proportion of B leading to superior external quality plants.
Throughout the production-distribution chain (e.g., nurseries, wholesalers), leaf coloration is generally employed as an index indicative of pot plant vigor and health status [30,31]. In all three species under study, the highest proportion of B light in the spectrum (R70B30) was generally associated with increased SPAD value (Tables S2-S4). In Aechmea, leaf chlorophyll was also significantly increased under R70B30 (Table S2). Therefore, supplementary light with the highest proportion of B light in the spectrum (R70B30) additionally promotes pot plant ornamental value by increasing leaf coloration.
Under natural light, the period required for inflorescence emergence was 47.5, 55.9, and 76.3 d for Aechmea, Guzmania and Vriesea, respectively ( Figure 3). Supplementary light decreased this period ( Figure 3). Earlier studies also indicated accelerated flowering owing to enhanced light intensity [14,26]. We additionally show here that when an increased proportion of B light in the spectrum (R80B20 and R70B30 as compared to R90B10) was employed, the time required for inflorescence emergence was further reduced (Figure 3).
Supplementary light also increased inflorescence development (Figure 4). This is in accordance with earlier findings [14,26]. Notably, an increased proportion of B light in the spectrum (R80B20 and R70B30 as compared to R90B10) promoted inflorescence development in Aechmea and Guzmania (Figure 4). In this way, the time to commercial development stage can be considerably shortened.
Under supplementary light, photosynthesis rate is higher [38]. This enhanced rate is associated with increased light level, though improved photosynthetic efficiency may be a contributing factor [10,11]. In this study, the functionality of photosynthetic apparatus was assessed by both F v /F m imaging (providing spatial pattern) and OJIP test. Results obtained by either protocol indicated that supplementary light generally induced minor effects on photosynthetic apparatus state (Tables S5-S7). A notable exception to this trend was the negative effect of R90B10 on F v /F m in Aechmea and Vriesea (Tables S5 and S7; see also Figure 5). Therefore, the noted differences in growth and flowering were not related to variation in photosynthetic efficiency.

Conclusions
A greenhouse study was conducted to elucidate the effect of supplementary light quality and nutrient solution EC on plant growth, and inflorescence development in three bromeliad species. Light regimes included solar light, and this supplemented with R90B10 (90% R and 10% B), R80B20 (80% R and 20% B), and R70B30 (70% R and 30% B). EC was set to 1 or 2 dS m -l . The higher EC promoted growth, as well as inflorescence emergence and development in Aechmea. By contrast, it induced negative effects in Guzmania and Vriesea. In these two species, supplementary light slightly alleviated the higher EC-induced negative effects. With few notable exceptions, supplementary light generally induced minor effects on the photosynthetic apparatus state. Depending on the species, supplementary light improved decorative features (plant height, offshoot number, crown thickness, tank volume, and leaf area). In all three species, supplementary light improved root and inflorescence weight, and promoted biomass allocation to generative organs. Importantly, it also sped up inflorescence emergence and improved inflorescence development. In this perspective, the duration needed for commercial ripeness was considerably reduced. These effects were more prominent under an increased proportion of B light in the spectrum (R80B20 and R70B30 as compared to R90B10). Supplementary light with increased B fraction results in a shorter production cycle owing to the more rapid emergence and enhanced development of the inflorescence and is highly recommended for commercial use.
Supplementary Materials: The following are available online at https://www.mdpi.com/article/ 10.3390/horticulturae7110485/s1, Figure S1. Time to inflorescence emergence following acetylene treatment as a function of nutrient solution electrical conductivity (EC) in the three species under study. Data of the four light treatments were pooled. A total of 16 replicate plants were assessed per treatment. Error bars represent SEM, Figure S2. Inflorescence development as a function of nutrient solution electrical conductivity (EC) in the three species under study. Data of the four light treatments were pooled. The scale (1 to 5) characterizing inflorescence development is provided in Figure 1. A total of 16 replicate plants were assessed per treatment. Error bars represent SEM, Table. S1: effect of supplementary light and nutrient solution electrical conductivity (EC) on dry mass partitioning of the three species under study, Table S2: effect of supplementary light and nutrient solution electrical conductivity (EC) on leaf osmotic potential, photosynthetic pigment content and SPAD value of Aechmea 'Primera' plants, Table S3: effect of supplementary light and nutrient solution electrical conductivity (EC) on leaf osmotic potential, photosynthetic pigment content and SPAD value of Guzmania 'Rostara' plants, Table S4: effect of supplementary light and nutrient solution electrical conductivity (EC) on leaf osmotic potential, photosynthetic pigment content and SPAD value of Vriesea 'Splenriet' plants, Table S5: effect of supplementary light and nutrient solution electrical conductivity (EC) on leaf photosynthetic functioning of Aechmea 'Primera' plants, Table S6: effect of supplementary light and nutrient solution electrical conductivity (EC) on leaf photosynthetic functioning of Guzmania 'Rostara' plants, Table S7: