Plant-Based Methods for Irrigation Scheduling of Woody Crops

The increasing world population and expected climate scenarios impel the agricultural sector towards a more efficient use of water. The scientific community is responding to that challenge by developing a variety of methods and technologies to increase crop water productivity. Precision irrigation is intended to achieve that purpose, through the wise choice of the irrigation system, the irrigation strategy, the method to schedule irrigation, and the production target. In this review, the relevance of precision irrigation for a rational use of water in agriculture, and methods related to the use of plant-based measurements for both the assessment of plant water stress and irrigation scheduling, are considered. These include non-automated, conventional methods based on manual records of plant water status and gas exchange, and automated methods where the related variable is recorded continuously and automatically. Thus, the use of methodologies based on the Scholander chamber and portable gas analysers, as well as those of systems for measuring sap flow, stem diameter variation and leaf turgor pressure, are reviewed. Other methods less used but with a potential to improve irrigation are also considered. These include those based on measurements related to the stem and leaf water content, and to changes in electrical potential within the plant. The use of measurements related to canopy temperature, both for direct assessment of water stress and for defining zones with different irrigation requirements, is also addressed. Finally, the importance of choosing the production target wisely, and the need for economic analyses to obtain maximum benefit of the technology related to precision irrigation, are outlined.


Precision Irrigation
Precision agriculture began in the 1960s with the use of geographic information systems (GIS), probably the first precision farming tools developed.In the late 1980s and early 1990s, Global Positioning System (GPS) receivers became available for agricultural users interested in making sustainable decisions, and this was the origin of modern practices in precision farming.Within the context of precision agriculture, the aim of precision irrigation (PI) is to irrigate each plant with the right amount of water and at the right time, for optimal input use efficiency and minimum environmental impact [1].Precision irrigation relies on an optimal combination of the irrigation system, the irrigation strategy and the irrigation scheduling method, as well as a wise choice of the production target.A huge variety of components are currently available on the market to adjust the irrigation system (furrow, sprinkling, localized . . . ) to the conditions of any farm or orchard, such that the effective choice and implementation of the irrigation system is usually accomplished without major difficulties.In this work, therefore, the most demanding steps for PI, i.e., on the wise choice of the irrigation strategy, the method for the assessment of water stress and for irrigation scheduling, and the definition of the most appropriate production target, are considered.
Precision irrigation usually implies the use of deficit irrigation (DI), because of its potential to increase crop water productivity (WP) [2].Achieving the greatest WP in a particular orchard implies a wise choice of the DI strategy.A variety of DI strategies have been defined, according to the amount and frequency of water supply (Table 1).Regulated deficit irrigation (RDI) is especially suitable for woody crops [3,4], including those in hedgerow orchards with high plant densities, currently considered among the most profitable management systems for fruit tree crops.The beauty of RDI is that it takes into account changes in the sensitivity of the crop to water stress at different developmental stages (e.g., as in Figure 1).This allows for maximum benefits of the supplied irrigation amounts.Regulated deficit irrigation, however, is challenging because it requires both a sound knowledge of the physiological response of the crop to water conditions and precise assessment of plant water stress levels along the growing cycle [5].Thus, precision irrigation has not been a suitable approach for farmers and orchardists until recently, when enough knowledge on major processes related to the impact of environmental conditions on the development and production of crops has become available, and advances in sensoring, monitoring and data transfer have been made.
Horticulturae 2017, 3, 35 2 of 38 Precision irrigation usually implies the use of deficit irrigation (DI), because of its potential to increase crop water productivity (WP) [2].Achieving the greatest WP in a particular orchard implies a wise choice of the DI strategy.A variety of DI strategies have been defined, according to the amount and frequency of water supply (Table 1).Regulated deficit irrigation (RDI) is especially suitable for woody crops [3,4], including those in hedgerow orchards with high plant densities, currently considered among the most profitable management systems for fruit tree crops.The beauty of RDI is that it takes into account changes in the sensitivity of the crop to water stress at different developmental stages (e.g., as in Figure 1).This allows for maximum benefits of the supplied irrigation amounts.Regulated deficit irrigation, however, is challenging because it requires both a sound knowledge of the physiological response of the crop to water conditions and precise assessment of plant water stress levels along the growing cycle [5].Thus, precision irrigation has not been a suitable approach for farmers and orchardists until recently, when enough knowledge on major processes related to the impact of environmental conditions on the development and production of crops has become available, and advances in sensoring, monitoring and data transfer have been made.Table 1.Name, brief definition and key reference papers of the most-used deficit irrigation strategies.

Supplementary or complementary irrigation
A single irrigation event is applied when a fixed threshold for water stress is achieved.Just 2 or 3 irrigation events in the irrigation season.Used when water for irrigation is very scarce or in temperate regions with low evapotranspiration rates or high rainfall.It can lead to substantial increases in crop performance, as compared to dry-farming, if the irrigation events are applied at the right moments of the growing cycle.
Abd-Eel-Rahman and El-Sharkawi [8]; Lavee et al. [9]; Proietti et al. [10] Low frequency deficit irrigation (LFDI) The soil is left to dry until the readily available water is consumed.Irrigation is then applied, until field capacity.This is repeated several times along the irrigation season.
Lavee and Wodner [11] Sustained deficit irrigation (SDI) A fixed fraction of the crop water needs is applied all throughout the irrigation season.Irrigation is applied daily or 2-4 times per week.
Goldhamer et al. [12]; Grattan et al. [13]; Ramos and Santos [14] Partial root zone drying (PRD) Similar to SDI, but water is applied to half of the root zone, switching to the other half every 2-3 weeks.
Dry et al. [15]; Fernández et al. [16] Regulated deficit irrigation (RDI) Irrigation amounts equal or close to the crop water needs are supplied at the phenological stages most sensitive to drought.Irrigation in those periods is applied daily, or at least several times per week.For the rest of the crop cycle, irrigation is drastically reduced (not only the dose is reduced but also the frequency, to one or two irrigation events per week) or even withheld.

Irrigation Scheduling from Plant-Based Measurements
Plant-based measurements are widely used both to assess water stress and to schedule irrigation.Measurements related to soil water or atmospheric demand are also useful for irrigation scheduling, but the advantage of plant-based measurements relies on using the plant as a biosensor, which integrates the soil and atmosphere water status as well as the plant physiological response to the available water.Different methods based on the measurement of plant variables have been developed with the purpose of scheduling irrigation (Table 2).The most widely used methods are either conventional, non-automated methods for measuring leaf or stem water status, stomatal conductance or photosynthesis, or methods in which records are taken continuously and automatically, based on measurements related to sap flow, trunk diameter and leaf turgor pressure, among other variables [19,20].The latter are those preferred for precision irrigation since, apart from running continuously and automatically, they can be implemented with data transmission systems for an easy and remote access to the recorded data through the Internet.In addition, those methods can be combined with remote imagery for the differential irrigation of zones within the orchard with different water requirements, which is one of the purposes of precision irrigation [21,22].Plant transpiration (E p ) depends on the difference between the "effective" soil water potential at the root surface (Ψ s ) and the "effective" leaf water potential for the whole canopy (Ψ l ), and on the soil-plant hydraulic resistance (R p ), as shown in Equation ( 1) [25]: A minimum Ψ s − Ψ l gradient (∆Ψ) must be achieved for water to flow from roots to leaves, thus allowing plant transpiration.During soil drying ∆Ψ increases, leading to increasing tension in the xylem, i.e., the xylem water potential (Ψ x ) decreases.This may cause an increasing number of embolized xylem vessels, with the consequent loss of hydraulic conductance and increasing R p [26].The role of stomata is to regulate CO 2 assimilation vs. water vapour loss.The loss of water through transpiration has the benefit of cooling down plants under high temperature conditions, but stomatal closure is required under drought to limit transpiration and avoid catastrophic xylem dysfunction [27].Stomatal regulation of leaf gas exchange is, therefore, crucial for the survival of plants under arid and semi-arid conditions, i.e., when precipitation is below potential evapotranspiration.This relevant role of stomata is likely behind its high sensitivity and quick response to a great number of stimuli, including hormonal and hydraulic signals generated in roots and leaves, the water status in the immediate vicinity of stomatal guard cells, and vapour pressure deficit of the air, D a [28,29].
Stomatal aperture is measured as the stomatal conductance (g s ), which is the inverse of the resistance offered by the stomata to the rate of passage of CO 2 entering, or water vapour exiting, through the stomata.Stomatal aperture changes constantly, depending on changes in soil water status and atmospheric demand, among other variables, such that g s measurements are highly informative on the response of the plant to water stress.Thus, g s is considered one of the most effective water stress indicators in terms of earliness and sensitivity [30,31].Measurements of g s can be easily made under field conditions by using porometers and infrared gas analysers (IRGAs) (Figure 2).The porometer can measure g s to water vapour while the IRGAs can measure g s to both water and CO 2 .Both devices have a chamber in which the whole leaf, or part of it, is enclosed during the measurement.If the cuticle is permeable to water vapour and CO 2 , the apparatus measures the leaf conductance (g l ).If the leaf has an impermeable cuticle, the measurement yields the stomatal conductance (g s ).Stomatal aperture depends markedly on the time of the day.The maximum daily stomatal conductance (g smax ), i.e., the g s value measured at the time of the day when stomatal opening is maximum, is widely used as a water stress indicator.When working with a species for which the daily dynamics of g s are unknown, daily curves of g s must be previously made to assess the time of the day at which g smax must be measured [32].In addition, information on the optimal environmental conditions leading to maximum potential g s values is valuable for properly assessing the meaning of field g smax measurements [33].
water and CO2.Both devices have a chamber in which the whole leaf, or part of it, is enclosed during the measurement.If the cuticle is permeable to water vapour and CO2, the apparatus measures the leaf conductance (gl).If the leaf has an impermeable cuticle, the measurement yields the stomatal conductance (gs).Stomatal aperture depends markedly on the time of the day.The maximum daily stomatal conductance (gsmax), i.e., the gs value measured at the time of the day when stomatal opening is maximum, is widely used as a water stress indicator.When working with a species for which the daily dynamics of gs are unknown, daily curves of gs must be previously made to assess the time of the day at which gsmax must be measured [32].In addition, information on the optimal environmental conditions leading to maximum potential gs values is valuable for properly assessing the meaning of field gsmax measurements [33].
Figure 2. Measuring leaf gas exchange in olive with a photosynthesis system (model LI-6400, LI-COR, Lincoln NE, USA), implemented with a tube to sample the air from above the tree canopies and a deposit for mixing the reference air before going through the analyzer (left).Detail of the chamber used for measurements under the prevailing light conditions (right).
Despite its significant potential as a water stress indicator, gs has limitations when used to schedule irrigation.First, both porometers and IRGAs must be operated manually, which limits the use of gs as a water stress indicator for precision irrigation.Recent advances, therefore, may change this.Hernandez-Santana et al. [34] reported a method to estimate gs from values of radial sap flux density and vapour pressure deficit of the air, two variables than can be continuously and automatically recorded under field conditions.Their findings show reliable estimations of gs, such that their approach opens the door for the use of gs as a water stress indicator in commercial fruit tree orchards under precision irrigation.Second, gs values are not always closely related to the plant water status.There are plants that are able to maintain a stable leaf water status over a wide range of Figure 2. Measuring leaf gas exchange in olive with a photosynthesis system (model LI-6400, LI-COR, Lincoln NE, USA), implemented with a tube to sample the air from above the tree canopies and a deposit for mixing the reference air before going through the analyzer (left).Detail of the chamber used for measurements under the prevailing light conditions (right).
Despite its significant potential as a water stress indicator, g s has limitations when used to schedule irrigation.First, both porometers and IRGAs must be operated manually, which limits the use of g s as a water stress indicator for precision irrigation.Recent advances, therefore, may change this.Hernandez-Santana et al. [34] reported a method to estimate g s from values of radial sap flux density and vapour pressure deficit of the air, two variables than can be continuously and automatically recorded under field conditions.Their findings show reliable estimations of g s , such that their approach opens the door for the use of g s as a water stress indicator in commercial fruit tree orchards under precision irrigation.Second, g s values are not always closely related to the plant water status.There are plants that are able to maintain a stable leaf water status over a wide range of atmospheric demand and soil water content.This is the case of the so-called isohydric species, which include maize and cowpea, among many others.In contrast, other species such as sunflower or barley are less effective at controlling leaf water status through stomatal closure, and they are termed anisohydric [35].Some species such as grapevine may show isohydric or anisohydric behaviour, depending on the water stress conditions [29,36].For other species, such as olive, a near-isohydric behaviour has been described, since they are able to keep relatively stable leaf water potentials but not as effectively as isohydric plants [37].In the case of plants with isohydric behaviour, a significant decrease of g s occurs during the day while leaf water potential remains constant.The decrease of g s can be due not only to soil drying but to increasing atmospheric demand.Also, variability of water distribution in the rhizosphere, not only changes in the average available soil water, may cause significant changes in stomatal closure and thus in g s [5].Further details on the efficiency of g s as a water stress indicator, depending on the isohydric or anisohydric behaviour of the plant, are given in the next section.
Finally, when using g s as a water stress indicator, it must be taken into account that the impact of stomatal closure on plant transpiration (E p ) depends on how well-coupled the crop canopy is with the atmosphere.Tall, rough canopies such as those of fruit tree orchards have aerodynamic conductances that are much greater than those of the short, smooth canopies of field and vegetable crops.Short canopies, particularly under low wind, are poorly coupled and offer much more resistance to mass transfer [38].Under poor coupling, stomatal closure is less effective at controlling E p because canopy temperature increases which, in turn, increases the vapour pressure gradient between the leaf and the atmosphere, increasing E p .In well-coupled orchards, however, the greater heat transfer from leaves prevents large differences between canopy and air temperature, leading to a nearly linear relation between E p and canopy resistance.Stomatal closure, therefore, will be more effective at reducing E p in crops with tall canopies than in those with short canopies, particularly under low wind [2].

Leaf and Stem Water Potential
The plant water status is highly related to its performance, i.e., to growth, fruit size and fruit yield.It is not surprising, therefore, that a number of variables related to plant water status are being used as water stress indicators for irrigation scheduling.This is the case of predawn water potential (Ψ pd ), i.e., the water potential measured in the plant just before dawn, and leaf (Ψ l ) and stem water potential (Ψ stem ) measured at midday.The term "midday" refers here to the time of the day when minimum values of Ψ l or Ψ stem are recorded, which can be 2-4 h after solar noon [32].That time is species-dependent and must be determined for the species of interest before using midday Ψ l or Ψ stem values for irrigation scheduling.Both Ψ pd and leaf Ψ l can be measured in single leaves.For the measurement of Ψ l , well-developed, young leaves are sampled from outer, well-exposed locations of the canopy.In plants with tall canopies, leaves are usually sampled at about 1.4-1.7 m aboveground.During the night, differences in water potential within the plant are reduced, especially in plants that do not transpire at night, such that the location of the sampled leaf for the measurement of Ψ pd is not so crucial.Still, leaves close to the base of the trunk are usually preferred for Ψ pd measurements [39].For Ψ stem , either single leaves or shoot tips from the inner part of the canopy, close to the trunk or to a main branch, are wrapped in aluminum foil or enclosed in aluminum plastic bags some 1-2 h before sampling, to prevent transpiration [40,41].Thus, the water potential of those leaves became similar to that in the xylem of the stem in the vicinity of the leaf or shoot attachment.
Measurements of Ψ pd are hardly used in commercial orchards, because of the need of measuring before dawn.For Ψ l and Ψ stem , it is widely recognized that Ψ stem could be a better indicator of water stress because it is less influenced by changing weather conditions than Ψ l and, consequently, it shows less variability.The work by Garnier and Berger [42] is among the first studies reporting better performance of Ψ stem than Ψ l as a water stress indicator with potential for irrigation scheduling.Naor [40,43] also reported a greater sensitivity of Ψ stem as compared to Ψ l , from measurements in apple, nectarine, lychee, grapevine and Japanese plum, and a high correlation with fruit weight and yield.Naor [43] provided detailed information on the reliability of Ψ pd and midday Ψ l and Ψ stem as water stress indicators.These three indicators are measured with Scholander-type pressure pumps, also called pressure chambers [44] (Figure 3).Measuring immediately after sampling is recommended, but this obliges transport of the Scholander chamber and related gear to the sampled plants, which can be both tedious and expensive.An alternative is to enclose the sampled leaf or shoot tip in an opaque container with wet paper inside, and keep it at low temperatures while being transported to the lab for measurement.Under these conditions of no light, air humidity close to 100% and low temperature, the sampled material can be kept for hours without significant change in water potential.Both Turner [45] and Hsiao [46] provided useful tips on the correct use of the Scholander chamber.Basically, the end of the leaf petiole or shoot tip should not be cut again before measurement.The flow of gas inside the chamber must be adjusted to ca. 0.1 bar s −1 (although the SI unit for plant water potential is the MegaPascal, or MPa, the bar unit is widely used for low water potential values; 1 bar = 0.1 MPa).If the material is severely stressed, the flow rate could be adjusted to an increase in pressure of 0.5 bar s −1 , to shorten the measuring time.Greater rates of pressure increase within the chamber will lead to an increase in temperature and to errors due to the inertia between the increase in pressure and the appearance of water in the cut end, caused by the plant hydraulic resistance.It is also important to determine precisely the point at which water appears at the cut end.The wetting of the tissue, which must be observed with a magnifying lens, is enough.A dome of liquid water with bubbles coming out of the cut end means that the pressure inside of the chamber went too high.
Greater rates of pressure increase within the chamber will lead to an increase in temperature and to errors due to the inertia between the increase in pressure and the appearance of water in the cut end, caused by the plant hydraulic resistance.It is also important to determine precisely the point at which water appears at the cut end.The wetting of the tissue, which must be observed with a magnifying lens, is enough.A dome of liquid water with bubbles coming out of the cut end means that the pressure inside of the chamber went too high.Precautions must be taken when using the Scholander chamber in plants showing isohydric behaviour.Measurements of Ψpd provide information on the level of rehydration that the plant has achieved overnight.Therefore, Ψpd it is not influenced either by the isohydric/anisohydric behaviour of the plant or by daily adjustments of osmotic potential (Ψπ).The leaf water potential (Ψl), however, may be affected by both processes.Thus, neither Ψl nor Ψstem at midday are sensitive water stress indicators in plants showing isohydric behaviour, since the plant water status will change little Precautions must be taken when using the Scholander chamber in plants showing isohydric behaviour.Measurements of Ψ pd provide information on the level of rehydration that the plant has achieved overnight.Therefore, Ψ pd it is not influenced either by the isohydric/anisohydric behaviour of the plant or by daily adjustments of osmotic potential (Ψ π ).The leaf water potential (Ψ l ), however, may be affected by both processes.Thus, neither Ψ l nor Ψ stem at midday are sensitive water stress indicators in plants showing isohydric behaviour, since the plant water status will change little despite significant changes in plant transpiration (Figure 4).For these plants, however, g s is very sensitive, since the stomata will close as soon as soil water decreases.The contrary can be said for plants with anisohydric behaviour: Ψ l is a sensitive indicator of soil water depletion and g s is not.Both the capacity of osmotic adjustment and vulnerability to embolism of the sampled plant also have an influence on the sensitivity of Ψ l as water stress indicator.The leaf water potential depends on the turgor (Ψ P ) and osmotic potentials, such that Many species of arid and semi-arid areas have a large capacity for osmotic adjustment under soil-drying conditions, which allows the plant to keep high transpiration rates despite significant soil water depletion, since Ψ l can reach low values before Ψ P is markedly affected.This feature of reaching low Ψ l values without affecting turgor pressure allows for keeping constant ∆Ψ despite significant decreases in Ψ s .This is an adaptive advantage for plants of semi-arid climates such as olive [47] since, according to Equation (1), it allows the plant to keep constant E p values until a significant soil water depletion is reached (Figure 5).The plant transpiration (E p ) can also be defined in terms of canopy conductance (G c ), as where D l-a is the leaf-to-air vapour pressure deficit and P is the atmospheric pressure.Combining Equations ( 1) and ( 3) results in with K as the hydraulic conductivity.The plant will limit E p by closing stomata, i.e., by reducing G c , before the loss of K reaches the limit for catastrophic hydraulic failure [27].In species with a high capacity for osmotic adjustment, embolism will occur at a greater soil water depletion than in plants without such adaptive traits.In those plants, by the time the stomata finally close to avoid catastrophic hydraulic failure, water in the soil will be quite low and the recovery of the soil water status by irrigation will take longer.
Finally, there is a controversy in the scientific community on the meaning of the water potential measurements made with the Scholander chamber, described by Bentrup [48].Basically, Zimmerman et al. [23] questioned whether the output of this tool, what they called the balancing pressure (P b ), reflects a 1:1 balance between the xylem tension in the intact plant, as it is widely recognized, and the chamber pressure.They stated that the actual tension in the xylem vessels cannot be as low as the values derived from the use of the Scholander chamber.Still, they acknowledged that the Scholander chamber is useful for detecting relative changes in turgor pressure.Zimmermann et al. [23] also claimed, in fact, that the cohesion-tension theory, widely accepted to explain the water ascent in plants, is misleading.Instead, they proposed the "multi-force" theory, which states that the ascent of water is not due just to the tension caused in transpiring leaves, but to forces of different kinds acting together.The user of the Scholander chamber, therefore, must take into account that the meaning of the output can be different depending on the approach adopted to explain the ascent of water in plants.An example is given by Fernández et al. [49] for the interpretation of measurements of Ψ l in olive trees.
Both leaf and stem water potential can also be determined with thermocouple psychrometers (TCP).Although difficult to use in the field, mainly because of daily changes in air temperature, some TCP instruments can be used under field conditions [50,51].Recently, a new type of small tensiometer has been developed for the measurement of water potential in plants.The device has a microelectromechanical (MEM) pressure sensor and a nanoporous membrane [52], and it is small enough to be embedded into plant stems to directly measure plant water potentials, down to about −10 MPa.According to the developers, this new technology has potential for automatic and continuous measurement of water potential in plants under field conditions.It was not until the development of the crop water stress index (CWSI, see below), however, that the method gained potential to schedule irrigation.Still, the method has been mostly used for research purposes only.Recently, however, the development of both cheaper image acquisition systems and user-friendly, powerful data image processing packages has substantially increased the potential of the method for irrigation scheduling in commercial orchards [55,56].Thermal readings can be made both at the plant level (ground-based imagery) [55,57] and from above the crop (airborne imagery), after installing the sensors on towers or cranes [58,59], on unmanned aerial vehicles (UAVs), also known as remote piloted aerial systems (RPAS) [60], planes [61] or satellites [62,63].Ground-based and airborne thermal images can be combined to assess within-orchard spatial heterogeneity in water status, as demonstrated with grape [64] and olive plants [65].The principles of thermal sensing are described elsewhere [66,67] and nice examples on both the linking between thermal imaging to main physiological indicators [68] and the use of thermal imaging for irrigation scheduling [56,60,66,69] can be found in the literature.
Thermal sensing has two main constraints for precision irrigation.First, canopy temperature is related to leaf water status, but it also depends on radiation, air temperature, air humidity and wind speed, among other factors.Therefore, the use of T c in the field as a water stress indicator requires normalizing T c values relative to a reference.This can be done with the CWSI approach, as described in Equation ( 5) [24,70]: In this equation, T nwsb is the temperature of a non-water stressed reference crop under similar conditions, and T max is an upper temperature for a non-transpiring crop.Due to a number of inconveniences, which include the difficulty of having a non-transpiring crop reference, a number of alternatives to the CWSI have been proposed [71].Still, both a T dry and T wet temperature reference, representing a non-transpiring leaf and a fully transpiring leaf, are required.A variety of artificial and natural wet and dry surfaces have been used for empirical determination of T dry and T wet [71].Also, analytical methods for CWSI calculation have been proposed [58,67].A second constraint of thermal sensing for precision irrigation is that full automation is not possible because of the need to process the thermal images.Despite those limitations, airborne imagery has a high potential for application to precision irrigation, since it allows for the zoning or zonification of farms and orchards, a process required for differential irrigation (Section 2.4).
The time of the day at which thermal images are taken has a great impact on the obtained information.This is because stomatal aperture changes dramatically during the day, influencing transpiration and thus leaf temperature (T l ).Also, the major weather variables related to both T l and T c change substantially along the day.If a single snapshot per day is taken, Ben-Gal et al. [58] recommended to take it at the time of maximum stress.They worked with olive trees, for which minimum daily values of Ψ l were recorded in early afternoon.In general, the measurement of T c by infrared thermometry is more advisable for field and row crops than for tree crops, because of differences on coupling between the canopies and the atmosphere and the impact on transpiration.

Ground-Based Imagery
Both infrared thermometers (IRT) and thermal cameras can be used for T c readings.There are non-expensive, robust, wireless models of IRT that are installed in the field for collecting T c readings with a frequency of seconds or minutes, and storing average values every minute or fractions of an hour [72,73].Infrared thermometers perform better with low, homogeneous crops growing in regions with rather constant weather conditions [67].Recently, however, the use of thermal cameras has become popular, thanks to lower prices and higher resolution.The best distance, angle, and time of the day at which the images should be taken must be checked for the crop conditions.Not only the species, but also the cultivar [74] and developmental stage [59] have an influence on the readings.The user must also bear in mind that relationships between thermal readings and water-stress-related physiological variables must be determined to properly evaluate the information provided by thermal imagery [66,75].The literature provides examples on the use of ground-based thermal imagery to detect water status changes in a variety of plants, from ornamental [76] to herbaceous [59,77] and woody crops [57,68,78].

Airborne Imagery
As mentioned above, thermal images can be taken from unmanned aerial vehicles (UAVs), planes and satellites.Also, sensors mounted on a truck-crane have been used to monitor the whole orchard [79].Airborne imagery is usually applied with two main purposes in this context, either to provide spatial distribution and variability of plant water status or to schedule irrigation.The first can help with the identification of zones within the farm or orchard with different sensitivity to water stress (zoning or zonification), and the selection of representative plants to be measured (Section 2.4).Agam et al. [79], for instance, assessed the spatial distribution of tree water status in an olive orchard, and suggested the procedure for choosing those trees best representing the orchard.The development of small, light, inexpensive thermal infrared (TIR) cameras, together with the appearance of low-cost, user-friendly unmanned aerial vehicles (UAVs), also known as remote piloted aerial systems (RPAS), has increased the applicability of airborne imagery to commercial orchards (Figure 6).
(Section 2.4).Agam et al. [79], for instance, assessed the spatial distribution of tree water status in an olive orchard, and suggested the procedure for choosing those trees best representing the orchard.The development of small, light, inexpensive thermal infrared (TIR) cameras, together with the appearance of low-cost, user-friendly unmanned aerial vehicles (UAVs), also known as remote piloted aerial systems (RPAS), has increased the applicability of airborne imagery to commercial orchards (Figure 6).When thermal readings are taken with UAVs to assess the heterogeneity in water status within the orchard, flights are made around noon, on different days after an irrigation event, to detect increasing water stress differences among zones with different sensitivity to water stress.Examples are given by Gonzalez-Dugo et al. [21] for almond, apricot, peach, lemon and orange orchards, by Bellvert et al. [64] for a vineyard, by Gonzalez-Dugo et al. [22] for pistachio and by Egea et al. [65] for olive.Gago et al. [60] reviewed the use of different remote sensors providing a variety of indices (NDVI, TCARI/OSAVI and PRInorm), mounted on different types of UAVs, for sustainable agriculture.They cited key papers on the use of airborne imagery for assessing not only water stress variability, but also plant photosynthesis and the impact of crop diseases.
Most authors using thermal images taken from UAVs and planes reported robust relationships between the derived CWSI and main physiological variables related to water stress, such as stomatal conductance and stem or leaf water potential [56,64,65], and claimed that the approach was suitable for characterizing plant water status variability in woody crops.Remote sensing data acquired by satellite sensors can be used to derive daily evapotranspiration (ET) maps.Images from some satellites are free of charge, but both the return interval, about two weeks or more in some cases, and the spatial resolution, over 15 m for most satellites, are limiting for precision irrigation.The image downscaling method can be used to improve spatial resolution, such that ET maps for irrigation scheduling purposes can be derived [62].Image fusion is also being proposed as a method to obtain higher spatial and spectral resolution images useful for irrigation management [63].When thermal readings are taken with UAVs to assess the heterogeneity in water status within the orchard, flights are made around noon, on different days after an irrigation event, to detect increasing water stress differences among zones with different sensitivity to water stress.Examples are given by Gonzalez-Dugo et al. [21] for almond, apricot, peach, lemon and orange orchards, by Bellvert et al. [64] for a vineyard, by Gonzalez-Dugo et al. [22] for pistachio and by Egea et al. [65] for olive.Gago et al. [60] reviewed the use of different remote sensors providing a variety of indices (NDVI, TCARI/OSAVI and PRInorm), mounted on different types of UAVs, for sustainable agriculture.They cited key papers on the use of airborne imagery for assessing not only water stress variability, but also plant photosynthesis and the impact of crop diseases.
Most authors using thermal images taken from UAVs and planes reported robust relationships between the derived CWSI and main physiological variables related to water stress, such as stomatal conductance and stem or leaf water potential [56,64,65], and claimed that the approach was suitable for characterizing plant water status variability in woody crops.Remote sensing data acquired by satellite sensors can be used to derive daily evapotranspiration (ET) maps.Images from some satellites are free of charge, but both the return interval, about two weeks or more in some cases, and the spatial resolution, over 15 m for most satellites, are limiting for precision irrigation.The image downscaling method can be used to improve spatial resolution, such that ET maps for irrigation scheduling purposes can be derived [62].Image fusion is also being proposed as a method to obtain higher spatial and spectral resolution images useful for irrigation management [63].

NIR Spectroscopy
The spectral reflectance of leaves in the visible to near-infrared (400-1100 nm) and infrared (1100-2500 nm) wavelength regions provides information on their water content.For whole canopies of plants under field conditions, near-infrared (NIR, 700-1100 nm) spectral indices are useful water stress indicators [80,81].Thus, field-measured hyperspectral remote sensing data is being successfully used to estimate leaf water content and leaf water potential in vineyards [82][83][84][85], cotton fields [86] and maize [87], among other crops.
The principles of spectroscopy were well described by Cozzolino [88].Basically, absorption frequencies can be used to identify specific chemical groups present in a vegetal sample.Thus, the relative proportions of C-H, N-H and O-H bonds of organic molecules can be identified by near-infrared (NIR) spectroscopy.The sample is irradiated with NIR radiation and the reflected or transmitted radiation is measured.Because water is a primary constituent of leaf tissues, the NIR reflectance spectra is dominated by the water spectrum, which shows overtone bands of the OH bonds at 760, 970 and 1450 nm and a combination band at 1940 nm [89].Recent advances both in hardware (NIR spectrometers and related systems for data storage) and software (mathematical models for identifying different components in the spectrum of the sampled material, chemometrics) have allowed the development of on-the-go or in-field NIR spectroscopy methods for assessing plant water status, among other crop characteristics [85].Although robust correlations between observed and predicted water potential have been reported [84,85,90], the price of the equipment, the cost of data acquisition (portable NIR spectrometers and related systems are usually mounted on vehicles than run through the orchard) and the need for substantial data processing are limiting factors for the use of this approach in a context of precision irrigation.

Sap Flow
A variety of methods have been developed for sap flow-related measurements, as detailed on the website of the Working Group on Sap Flow of the International Society for Horticultural Science (http://www.ishs.org/sap-flow/ishs-working-group-sap-flow-online-resources).The website provides a short description of the main methods, references to key papers, and a list of manufacturers, among other information.For the correct use of terms, units and symbols related to sap flow, the papers by Edwards et al. [91] and Lemeur et al. [92] are recommended.Sap flow-related measurements are widely used in research for in situ determinations of plant water consumption and transpiration dynamics (Figure 7), and their potential for irrigation scheduling has been assessed by Nadezhdina [93], Fernández et al. [94,95] and Jones [30], among others.Devices to schedule irrigation automatically from sap flow measurements have been designed and tested in fruit tree orchards [96,97], and comparisons with other methods to monitor plant water stress and to schedule irrigation have been made for a variety of crops, including apple [93], grapes [98], lemon [99], plum [100] and olive [101,102], among other species.In a recent review, Fernández [20] analysed the applicability of sap flow-related measurements for assessing water stress and irrigation scheduling in commercial orchards.Sap flow sensors are robust and reliable enough for operation in the field over extended periods of time, and they are easily automated and implemented with data transmission systems.These features confer a high potential for use in precision irrigation.Yet their suitability for scheduling irrigation depends on the water stress indicator derived from the sap flow measurements.When the total plant sap flux is obtained with an invasive method (see the website mentioned above for differences between invasive and non-invasive sap flow methods), calibration of the raw data is required, for which correction factors must be previously derived for the species of interest [94,103,104].In addition, a high number of sensors are usually required for trees with trunks of large diameter, because the azimuthal sap flow variability is usually high.The system becomes costly and time-and labor-consuming, and the user must be trained for the required data processing.These requirements curtail the use of this approach in commercial orchards.This explains the use of alternative water stress indicators derived from sap flow-related measurements.Nadezhdina and Čermák [96] used what they called the Sap Flow Index (see Nadezhdina [93] for details) to control irrigation in fruit tree orchards.Both Fernández et al. [94] and Nadezhdina et al. [105] suggested the possibility of using the ratio of sap flow in the inner/outer xylem regions as a trigger for when to Sap flow sensors are robust and reliable enough for operation in the field over extended periods of time, and they are easily automated and implemented with data transmission systems.These features confer a high potential for use in precision irrigation.Yet their suitability for scheduling irrigation depends on the water stress indicator derived from the sap flow measurements.When the total plant sap flux is obtained with an invasive method (see the website mentioned above for differences between invasive and non-invasive sap flow methods), calibration of the raw data is required, for which correction factors must be previously derived for the species of interest [94,103,104].In addition, a high number of sensors are usually required for trees with trunks of large diameter, because the azimuthal sap flow variability is usually high.The system becomes costly and time-and labor-consuming, and the user must be trained for the required data processing.These requirements curtail the use of this approach in commercial orchards.This explains the use of alternative water stress indicators derived from sap flow-related measurements.Nadezhdina and Čermák [96] used what they called the Sap Flow Index (see Nadezhdina [93] for details) to control irrigation in fruit tree orchards.Both Fernández et al. [94] and Nadezhdina et al. [105] suggested the possibility of using the ratio of sap flow in the inner/outer xylem regions as a trigger for when to irrigate.Recently, Hernandez-Santana et al. [34] developed an approach to derive stomatal conductance (g s ) values from sap flow measurements.They demonstrated that it is possible to estimate g s in trees under field conditions, automatically and continuously, by using sap flux density (J p ) data directly, without the need for up-scaling to tree transpiration.They worked with olive, a species that has up to 3-year-old leaves.Basically, variations in the radial profile of J p in the sapwood recorded in this species were attributed to a differential transpiration between younger leaves, better connected to the outer layers of the sapwood, and older leaves, better connected to inner sapwood.In addition, J p data were taken at two depths only below the cambium (at 5 and 10 mm), instead of the four depths required when the system is used in a standard way.As mentioned in Section 2.1.1,this new approach may favour an increasing use of sap flow measurements in orchards under precision irrigation.

Stem and Fruit Diameter
After stomatal opening early in the morning, a tension is created from the evaporative surface of the leaves to any water-storing organ of the plant, i.e., to the stem, branches, roots, leaves, and fruits [106][107][108].Water stored in the tissues during the night is then lost, allowing the plant to respond rapidly to changes in atmospheric demand, prior to water uptake by the roots [109].Thus, water from the phloem and related tissues, as well as from the living tissues of the sapwood, is lost by transpiration, so that the stem diameter decreases [110][111][112].Changes in the water content of extensible tissues of the stem are readily reversible, such that later in the day and during the following night, the plant rehydrates and stem diameter increases.This causes stem diameter variation (SDV).In trees, daily SDV usually ranges from a few tenths to a few hundred microns, depending, among other factors, on stem diameter and wood elasticity [113,114].For some purposes, it may be advisable to convert the SDV data to areas and normalise by the initial area in order to obtain comparable, size-independent measurements of daily dimensional changes [115].
On days of high soil water availability and low atmospheric demand, and when the plant is in a period of active growth, stem diameter increases from one morning to the next, with little, if any, decrease during the day.If both the soil water availability and the atmospheric demand are high, stem diameter also increases from one morning to the next, but an appreciable decrease could take place during the day, as a result of plant growth and tissue dehydration in the morning and rehydration after stomatal closing later in the day.On days when the soil is dry and the evaporative demand is high, there is a reduction in stem diameter, with only a partial recovery during the night.Under those conditions, the stem diameter can remain stable or even decrease from one day to the other, because the plant does not grow and becomes increasingly dehydrated [109,116,117].The work by Herzog et al. [118] gives additional information on the diurnal dynamics of SDV, and how it is related to the diurnal dynamics of transpiration.
Different water stress indicators can be derived from the resulting daily patterns of SDV, as summarized in Table 2.For details, see Goldhamer and Fereres [119], Gallardo et al. [120], Fernández and Cuevas [113] and De la Rosa et al. [121], among others.For scheduling irrigation, the maximum daily shrinkage (MDS) and stem growth rate (SGR) are the most widely used of these indicators.Values of MDS, however, must be used with care since, for some species, the MDS vs. Ψ stem relationships show diurnal hysteresis (lag) and seasonal changes.Also, and very important, for some species MDS increases as the plant water potential falls to a certain value, after which MDS decreases as the plant water potential becomes more negative.This has been reported for peach, lemon, grapevine and olive, among other species [114].On the other hand, SGR cannot be used as an indicator of plant water stress in periods of negligible growth, for instance in grapevines after veraison (ripening) [122].Thus, expert interpretation of SDV records is required before using them for scheduling irrigation, which limits their potential for automating the calculation of the irrigation dose [20].
Additional complications in data interpretation come from the fact that the patterns of SDV are affected not only by environmental water conditions and growth patterns, but also by plant age and size, and crop load, among other factors.For young trees, and in periods of rapid stem growth, SGR could be a better indicator than MDS.This is because MDS, for those trees and conditions, could be affected more by growth than by the level of water stress.This has been observed in peach [119], olive [123], lemon [124], and almond [125], among other species.On the other hand, in periods of negligible growth because of active fruit development, SGR is not a reliable indicator of plant water stress.This has been observed in grapevines [122], plum [126], and olive trees [127].The seasonal growth patterns of any plant also depend on the crop load, so this is another factor influencing SDV records.In olive trees, a species with marked alternate bearing, trees with heavy fruit load ('on' year) exhibited the most-active trunk growth until some four weeks after full bloom, and grew very slowly for the rest of the season, while trees with a light crop load ('off' year) grew steadily throughout the season at an increasing rate [128].In plum trees, Intrigliolo and Castel [129] found that during most of the fruit growth period, when SGR was minimum, MDS was higher in the less-irrigated treatment than in the control, and correlated well with Ψ stem .After harvest, however, when SGR was higher, the MDS vs. Ψ stem correlation decreased as the season progressed.De Swaef et al. [130] provided an explanation on the effect of crop load on MDS and daily growth rate (DGR) in peach, with the help of a water and carbon transport model.The use of models to interpret SDV records was reviewed by De Swaef et al. [131].Other factors have been also been identified as influencing SDV records.Thus, Intrigliolo and Castel [129] suggested an influence of the soil volume wetted by irrigation, and Gallardo et al. [120] found that the signal values of MDS recorded in potted pepper plants in a greenhouse were greater those in soil-grown pepper plants, and suggested that the small rooting volume of pots favoured that response.Also, Silber et al. [132] suggested that the water-stress history of avocado trees, rather than the actual plant-water status, could have influenced maximum trunk diameter variation (MTDV).
Despite difficulties in data interpretation, SDV has a potential application for precision irrigation because the current dendrometers and related systems are robust and precise, suitable for automatic recording and data transmission under field conditions (Figure 8).The first highly sensitive dendrometers and dendrographs were developed in the late 1800s [133,134] but it was not until the second half of the last century when technological advances allowed for precise SDV measurements [135][136][137].From the beginning of the 1990s, most authors working on irrigation scheduling have used linear variable differential transformers (LVDT), also called linear variable displacement transducers.The LVDT-type sensors are robust and of high precision, close to ±1 µm.In many cases, however, the resolution cannot be expected to be greater than about 10 µm, due to errors associated with calibration, voltage recording, temperature changes, and other factors [129].Ueda et al. [138] reported advantages (small size, light weight, low price, ease of use, and reliability) of the strain-gauge method over the LVDT-type sensor for estimating diurnal changes in stem and branch diameters of a large tree.The method was also used by Ueda and Shibata [106].
Some dendrometer models are nailed or screwed into the tree, either to support the instrument or to serve as a fixed reference against which growth is measured.Others are mounted on a holder that is attached tightly to the stem by elastic straps, which do not affect growth.Holders are usually of aluminum and INVAR, an alloy of Fe and Ni with negligible thermal expansion.In fruit trees and other plants of large stem diameter, dendrometers are installed on the side of the stem opposite to the sun's trajectory, to minimise negative effects of heating by direct solar radiation.They must be at a certain distance from the ground to avoid interference from growing weeds, and far from scars and other irregularities of the trunk surface.The outer, dead tissues of the bark must be removed before installation, allowing the contact point of the sensor to rest directly on the living tissues of the bark.
The dendrometer must always be in contact with the plant surface, for which a spring or glue can be used, and the whole area must be covered with insulating material and reflective thermoprotecting foil to minimise both heating by direct solar radiation and the impact of rain drops.Recommendations on dendrometer installation are given elsewhere [113].Once installed, the dendrometer is connected to a data logger programmed to automatically scan the sensor outputs every few seconds and store average values every few minutes.The data logger is usually provided with a system for data transmission.After installation the dendrometers can run for months or even longer with practically no maintenance.Still, LVDTs are particularly prone to obstruction by insects.
Different devices have been built to schedule irrigation from SDV records.Pelloux et al. [139] described the Pepista system marketed by the French company Agro-Technologie (www.agrotechnologies.com), and Bussi et al. [140] used it to control irrigation in a 10-year-old peach orchard.Other companies, such as the Spanish Verdtech (www.verdtech.es)and the Israeli Phytech (www.phytech.com),have developed automatic monitoring systems of SDV records.Examples of different approaches to scheduling different irrigation strategies from SDV records have been recently published for olive [141][142][143][144]), nectarine [121] and peach [145,146], among other species.These publications, together with that by Fernández [20], describe well the potential and limitations of the use of SDV records for irrigation scheduling.Contrary to use of SDV records, on which a large number of papers have been published, those on the use of fruit diameter as an indicator of water stress are very few.The first attempts to correlate changes in fruit diameter with environmental conditions for non-destructive estimates of water stress useful for irrigation scheduling, were made in the 1960s and 1970s [147].Devices range from digital calipers used manually [148,149] to automatic devices for accurate, continuous measurements [150].Recording fruit diameter is useful for studies on the impact of irrigation and other management and environmental factors on fruit production.Little attention has been dedicated, however, to the use of this approach for irrigation scheduling in commercial orchards.

Leaf Thickness
There is evidence of changes in leaf thickness in relation to soil and atmosphere water status, Contrary to use of SDV records, on which a large number of papers have been published, those on the use of fruit diameter as an indicator of water stress are very few.The first attempts to correlate changes in fruit diameter with environmental conditions for non-destructive estimates of water stress useful for irrigation scheduling, were made in the 1960s and 1970s [147].Devices range from digital calipers used manually [148,149] to automatic devices for accurate, continuous measurements [150].
Recording fruit diameter is useful for studies on the impact of irrigation and other management and environmental factors on fruit production.Little attention has been dedicated, however, to the use of this approach for irrigation scheduling in commercial orchards.

Leaf Thickness
There is evidence of changes in leaf thickness in relation to soil and atmosphere water status, suggesting a potential for plant water stress assessment [151,152].Leaf thickness-related measurements are made with devices containing linear potentiometer transducers (same principle as LVDT measurements).The method is non-invasive and suitable for online measurements.It seems that the method is more suitable for crops under cover, since wind in open field crops causes noisy records.Another disadvantage is that relationships between leaf thickness and leaf water status are not robust.They depend on the species, leaf type and age, stress history and other factors [153].In addition, recent findings published by Seelig et al. [154] showed a lack of correlation between leaf thickness and turgor pressure.Still, devices to schedule irrigation from leaf thickness-related measurements have been developed and tested in cowpea plants under greenhouse conditions [155] and in citrus, avocado and cotton crops under open field conditions [156].An additional problem for the use of the system in commercial farms and orchards is that, depending on the species and leaf-width gauge model, the user could be required to reinstall the sensors in new leaves quite often [157].

Leaf Turgor Pressure
Leaf turgor has a significant effect on stomatal behaviour and, thus, on plant water status and water consumption.Rodriguez-Dominguez et al. [158] measured drought responses of variables related to water stress in three important woody species in the Mediterranean climate (almond, grapevine and olive), and, with the help of a process-based g s model, found that responses mediated by leaf turgor could explain over 87% of the observed decline in g s across species.They used the stomatal model of Buckley et al. [159], also known as the BMF model, which is based on the hydroactive feedback hypothesis (HFH).That hypothesis states that guard cell osmotic pressure depends markedly on leaf turgor.The HFH hypothesis is supported by sound evidence, including a recent discovery by McAdam et al. [160] on a molecular mechanism for negative feedback regulation of guard cell osmotic pressure by leaf turgor.The close relation between g s and leaf turgor supports the utility of leaf turgor-related measurements as a valid indicator of water stress.
Measurements of turgor pressure in cells and xylem vessels can be made with sophisticated equipment requiring well-trained users, and include methods such as the ball tonometry method [161] and the pressure probe technique [23].Recently, Zimmermann et al. [162] developed the magnetic leaf patch-clamp pressure probe, known as the LPCP or ZIM probe (Figure 9), for leaf turgor pressure-related measurements under field conditions.Briefly, the probe consists of two metal pads in which two magnets are integrated.One of the patches also contains a pressure-sensing chip.The patches are located in the adaxial and abaxial sides of a leaf, such that the pressure chip is in close contact with the leaf surface.The distance between the magnets above and below the clamped leaf patch is adjusted according to the rigidity and elasticity of the leaf, by regulating the distance between the two magnets.The leaf turgor pressure (P c ) is determined by measuring the pressure transfer function through the leaf.The attenuation of the applied external pressure and, thus, the output pressure signal (P p ) provided by the ZIM probe, depends on the magnitude of P c .High P c attenuates the pressure transfer through the leaf patch and, in turn, P p is small.Therefore, P p is inversely correlated with P c .The ZIM probes are connected by cable to a radio transmitter (telemetric unit), which sends the collected data to a data logger (controller) implemented with a GPRS modem linked to an Internet server via the local mobile phone network.From the server, the data can be downloaded by smartphones, tablets and laptops.Thus, the collected data are available for the user in nearly real-time.If desired, the system can also measure air temperature, relative humidity and light intensity close to the plant, as well as soil temperature and moisture [163].
High Pc attenuates the pressure transfer through the leaf patch and, in turn, Pp is small.Therefore, Pp is inversely correlated with Pc.The ZIM probes are connected by cable to a radio transmitter (telemetric unit), which sends the collected data to a data logger (controller) implemented with a GPRS modem linked to an Internet server via the local mobile phone network.From the server, the data can be downloaded by smartphones, tablets and laptops.Thus, the collected data are available for the user in nearly real-time.If desired, the system can also measure air temperature, relative humidity and light intensity close to the plant, as well as soil temperature and moisture [163].
Figure 9. Installing the ZIM system in the orchard mentioned in Figures 1 and 6, with the help of Ulrich Zimmermann (in the photo on the right).ZIM probes (left) were connected to a radio Figure 9. Installing the ZIM system in the orchard mentioned in Figures 1 and 6, with the help of Ulrich Zimmermann (in the photo on the right).ZIM probes (left) were connected to a radio transmitter (central up), which sent the collected records to a data logger (central down) located in a weather-proof box at the base of a pool with two aerials (right), one for the radio signals and the other for sending the data from the data logger, via GPRS, to a server.
The ZIM probes work well in hydrated and moderately hydrated leaves.Above a certain level of dehydration, air and vapour accumulates in the leaf tissues and the pressure chip does not properly sense the turgor pressure.The extent to which this limitation curtails the potential of the ZIM probes to monitor water stress was assessed for olive by Fernández et al. [49] and Ehrenberger et al. [164].Other effects of the environmental conditions and plant hydraulic functioning on the performance of the ZIM probe, were detailed by Zimmermann et al. [163].The ZIM system has been tested in a variety of forest tree species [165], grapevines [166,167], and grapefruit [167], banana [168], persimmon [169] and olive trees [49,[170][171][172], as well as in herbaceous crops such as tomato [173], canola [174] and wheat [175,176].Also, comparative studies of the ZIM system vs.Scholander-type chambers have been made by Westhoff et al. [166] for grapevines, by Rüger et al. [165] for eucalyptus, avocado, grapefruit, beech and oak, and by Ben-Gal et al. [170] and Fernández et al. [49] for olive.These studies showed that the ZIM system is robust, relatively inexpensive, and suitable for automatic and continuous recording under field conditions for long periods of time, and that it has a great potential as a water stress indicator in vineyards and fruit tree orchards.Padilla-Díaz et al. [7] used it successfully to schedule a regulated deficit-irrigation strategy in a hedgerow olive orchard with high plant density.
Leaf turgor pressure can also be estimated with the Wiltmeter [177], a portable instrument for leaf turgor-related measurements suitable for working under field conditions.Earlier versions had some limitations, detailed by Aroca and Calbo [178], such that an R2 version was developed for simpler portable operation on the field [179].This version, however, still required user intervention, and measurements were influenced by the way the user operated the system.Recently, two new versions of the Wiltmeter have been released [178], which allow automated turgor pressure measurements at user-defined logging intervals.According to the authors, the new Wiltmeter can be used for both ecophysiological studies and irrigation scheduling, but, to our knowledge, no evidence of the latter has yet been published.

Stem Water Content
The principles of dielectric methods to measure water content in a medium are given elsewhere [180].Basically, the water content and electrolyte concentration of a medium can be accurately determined from the measurement of its dielectric properties.Water has a high dielectric constant (ε) of about 80, much higher than that of the air (ca. 1) or the dry constituents of many mediums (for dry soil, ε is about 5).Two methods have been developed based on the measurement of dielectric properties, one in the frequency domain between 30-3000 MHz and the other in the time domain at frequencies above one GHz.Time domain reflectometry (TDR) sensors are based on the latter.The principle of the technique is thoroughly explained by Topp and Davis [181].Measuring stem water content (θ stem ) by TDR assumes that soil water drying induces significant changes in the water content of tree stems.It is known that stems of many tree species undergo substantial seasonal variations in θ stem [182] and that water storage in the sapwood can make a significant contribution to daily transpiration under periods of high evaporative demand [183].By measuring θ stem with TDR in aspen, piñon, cottonwood and ponderosa pine trees, Constantz and Murphy [184] found absolute values for θ stem between 0.20 and 0.70 L L −1 , with an annual change in moisture content between 15% to 70%, depending on the species and water environmental conditions.Results of this type have been reported for many other species, as detailed by Nadler et al. [157].These authors used a TDR methodology to measure electrical conductivity in the stem of mango trees under changing water and salt conditions.They found that stem electrical conductivity (σ stem ) was primarily dependent on θ stem and only negligibly on stem cell salinity, and concluded that stem resistivity measurements could be used to represent dielectric changes in the stem.In a later study, they focused on a more user-friendly and less expensive tool, after stating that TDR was too expensive and complicated for commercial orchards.They studied the relations between σ stem and θ stem , both in tree stem segments [185] and in lysimeter-grown mango, banana, date and olive trees [186] (Figure 10), and confirmed that θ stem reacts sensitively and within minutes to water stress.They proved that resistivity measurements have lower scatter because θ stem vs. ε relationships are exponential and θ stem vs. σ stem relationships are linear.Also, the resistivity measurements were easier to make than the ε measurements, and allowed for smaller probes, longer cables, simpler multiplexing and a lower price, among other advantages.They concluded that there is a clear economic advantage in resistivity over ε measurements, and that the monitoring of σ stem has a potential in scheduling irrigation in fruit tree orchards.An example of the applicability of the method in vines was published by Coskun and Konukcu [187].They analysed the correlation between volumetric soil water content and σ stem , and concluded that further experiments on the suitability of σ stem measurements to both monitor water stress and schedule irrigation were needed to properly evaluate the performance of the methodology when applied to vines.To our knowledge the method has not been automatized yet, but authors claimed that automation is possible.
Horticulturae 2017, 3, 35 20 of 38 commercial orchards.They studied the relations between σstem and θstem, both in tree stem segments [185] and in lysimeter-grown mango, banana, date and olive trees [186] (Figure 10), and confirmed that θstem reacts sensitively and within minutes to water stress.They proved that resistivity measurements have lower scatter because θstem vs. ε relationships are exponential and θstem vs. σstem relationships are linear.Also, the resistivity measurements were easier to make than the ε measurements, and allowed for smaller probes, longer cables, simpler multiplexing and a lower price, among other advantages.They concluded that there is a clear economic advantage in resistivity over ε measurements, and that the monitoring of σstem has a potential in scheduling irrigation in fruit tree orchards.An example of the applicability of the method in vines was published by Coskun and Konukcu [187].They analysed the correlation between volumetric soil water content and σstem, and concluded that further experiments on the suitability of σstem measurements to both monitor water stress and schedule irrigation were needed to properly evaluate the performance of the methodology when applied to vines.To our knowledge the method has not been automatized yet, but authors claimed that automation is possible.

Electrical Potential
Stomatal closure can be triggered by long-and short-distance signaling, involving signals of different natures [188,189].Although most studies focus on signals of chemical or hydraulic nature, electrical signaling has received increasing attention in recent years.Although the first extracellular electrical measurements in plants date from the 19th century [190], Fromm and Eschrich [191] were among the first to hypothesize that changes in the electrical signals might be a mechanism of communication between roots and leaves.Since then, an increasing amount of evidence suggests that the bioelectric potential in plants is affected by a variety of environmental changes, including soil water availability.In work with maize plants, Fromm and Fei [192] observed that sieve tubes of

Electrical Potential
Stomatal closure can be triggered by long-and short-distance signaling, involving signals of different natures [188,189].Although most studies focus on signals of chemical or hydraulic nature, electrical signaling has received increasing attention in recent years.Although the first extracellular electrical measurements in plants date from the 19th century [190], Fromm and Eschrich [191] were among the first to hypothesize that changes in the electrical signals might be a mechanism of communication between roots and leaves.Since then, an increasing amount of evidence suggests that the bioelectric potential in plants is affected by a variety of environmental changes, including soil water availability.In work with maize plants, Fromm and Fei [192] observed that sieve tubes of the phloem serve as a pathway for electrical signal transmission from roots to leaves.In avocado trees, Gil et al. [193] found that changes in extracellular electrical potential between the leaf petiole and the base of the stem (∆V L-S ) may play a role in root to shoot communication when plants are under water stress.They outlined the need for separating true electrical signaling phenomena from conductivity changes arising from water or ion handling by the plant tissue, and concluded that changes in ∆V L-S may be a mechanism for root to shoot communication leading to stomatal closure in response to soil drying.Gurovich and Hermosilla [194], Gil et al. [195] and Oyarce and Gurovich [196] found that electrical signaling resulting from microenvironment modifications can be quantitatively related to the intensity and duration of the stimuli, as well as to the distance between the stimuli site and the location where electric potential is measured.They suggested the existence of a sort of proto-nervous system in plants, in agreement with suggestions made by other groups working on the subject [197][198][199].
Gurovich and Hermosilla [194] described a digital acquisition system for recording ∆V L-S with microelectrodes inserted 15 mm deep into the sapwood at various positions in the trunks of avocado, blueberry, lemon and young olive plants in pots (Figure 10), and discussed the potential of using ∆V L-S patterns, during day-night cycles and at different conditions of soil water availability, as tools to assess early plant water stress conditions.A different system was described and tested in cucumber plants under greenhouse conditions by Wang et al. [200].Recently, Ríos-Rojas et al. [201,202] developed a system for remote, real-time recording of plant electrical potential in the field and data transmission via Internet.The authors concluded that their system could be used to monitor water stress and, combined with soil moisture and potential evapotranspiration sensors, to schedule irrigation.

The Combined Use of Methods
The potential of combining sap flow (SF) and trunk diameter variation (TDV)-related measurements to assess water stress has been evaluated for a variety of species [108,113,203].The approach allows for deriving water stress indices [101,102], as well as modeling tools [204,205] for irrigation scheduling of fruit trees.Drew and Downes [206] and Fernández and Cuevas [113] reported main factors explaining agreements and disagreements between concomitant records of SF and TDV in the same plants.There is a consensus on the potential of the combined use of these two methods to better understand the water-flow dynamics within a plant [108,[203][204][205]207] and to assess both water stress [102] and water needs [101].Also, the combined use of SF and eddy covariance measurements is useful for assessing the partition of ET fluxes [208][209][210] and to derive crop coefficients for irrigation scheduling [211].Eddy covariance [212] and satellite observations [213] have also been combined with soil water balance simulations to derive the value of basal crop coefficients for the dual crop coefficient approach.Other examples relying on the use of combined measurements are provided by Centeno et al. [214] and Cancela et al. [215], who suggested combining measurements of soil water and plant water status to improve irrigation management in vineyards.
Additional examples on the joint use of two or more methods to gain insight into the use of water by plants have been published.Gibert et al. [197] made concomitant measurements of sap flow and daily electrical potential variations in a poplar tree.Findings suggested electrokinetic, as well as thermoelectrical and electrochemical effects acting together on transfer processes between the soil and the atmosphere.Rodriguez-Dominguez et al. [216] made concomitant measurements of sap flow and leaf turgor in olive trees, and compared the dynamics of both variables on cycles of increasing water stress and recovery.Their data adds insight in the processes related to water lifting in the trees.The reports by Diaz-Espejo et al. [217] and Hernandez-Santana et al. [34] illustrate well the potential of concomitant measurements of different plant variables for the development of reliable process-based models of water use by plants.

An Alternative to the Signal-Intensity Approach
Changes in records from water stress indicators can be due to variations in both soil water availability and atmospheric demand.When data is used for irrigation scheduling purposes, the coupling between plant water relationships and evaporative demand must be avoided.With that purpose, Goldhamer and Fereres [119] proposed what it is widely known as the signal-intensity approach.Basically, at the beginning of the irrigation season all the instrumented plants must be kept under non-limiting soil water conditions for enough days to calculate the so-called reference signal (Signal ref ), defined as Signal ref = average treatment WSI/average reference WSI (6) The treatment WSI is the water stress indicator derived from plant-based measurements (applicable to sap flow, trunk diameter, leaf turgor pressure . . . ) in representative plants that later, during the irrigation season, will be under the imposed irrigation treatment, normally a deficit-irrigation treatment.The average reference WSI is either determined from records on reference trees or estimated from a reference equation.To impose the desired water treatment during the irrigation season, Signal ref is multiplied by a threshold value, which yields the target signal (Signal target ), defined as The threshold value determines the level of deficit irrigation, such that is equal to 1 for no irrigation-related stress, while increasing values impose increasing stress levels.The threshold value must be determined from previous observations in the orchard, or obtained from the literature.This approach has been tested in orchards of various fruit tree species, including almond [218], peach [219] and lemon [220], and has disadvantages for its use in commercial farms and orchards.First, it is difficult to define the threshold value [30].Second, the high plant-to-plant variability normally found in commercial farms and orchards [221] may lead to the use of high numbers of sensors and related systems, with the consequent increase in installation and maintenance costs and in data processing.Goldhamer and Fereres [119] reported additional disadvantages of using over-irrigated plants as reference plants, such as excessive nitrogen leakage or problems in the root function of the reference plants due to hypoxia.They recommended frequent inspection of the reference plants to ensure they remain representative of those in the orchard during the irrigation season.Alternatively, rather than using over-irrigated plants, a reference rate of plant transpiration based on leaf area and local microclimate can be calculated with user-friendly models calibrated for the orchard conditions [222][223][224].An example for a vineyard is given by Green et al. [225].Also, soil water models properly evaluated for the orchard conditions can be combined with plant-based measurements to assess a reference plant transpiration [226,227].
The limitations of the signal-intensity approach for scheduling irrigation in commercial orchards were addressed by Fernández [20], who proposed a different approach based on the use of remote imagery.Recent developments in remote imagery techniques have lowered the cost of infrared images, which can be used to divide the orchard area into a number of zones with contrasting water-stress characteristics.This process, known as zoning or zonification, allows for differential irrigation within the farm or orchard, which is a main part of precision irrigation.The trees to be instrumented can then be chosen within each area, such that a reduced number of trees is enough to provide reliable information for scheduling irrigation in the orchard.After detecting the first signals of the onset of water stress in the most sensitive zone, the 3-day weather forecast is consulted to assess whether early adjustments in the irrigation schedule are required to avoid unwanted events of water stress in the orchard.This approach was successfully tested by Padilla-Díaz et al. [7] in a super-high-density olive orchard.It has to be taken into account that plant-based methods for irrigation scheduling inform on the right time for an irrigation event and on whether the irrigation dose must increase or decrease.They do not give reliable information, however, on the precise value of the irrigation dose.Thus, the new irrigation dose is normally determined from the previous one and increased or decreased by a certain percentage, which in most cases varies from 10 to 15% [7,219].

Choosing the Most Appropriate Method
The features of a water stress indicator that must be assessed to evaluate its performance have been addressed by different authors [41,113], and are summarized in Table 3.In addition, Fernández [20] detailed the requirements of the water stress indicators and the sensors and related systems for scheduling irrigation in commercial orchards (Table 4), and Egea et al. [228] considered financial aspects.A number of papers have been published on comparative studies between different water stress indicators, illustrating their performance for a variety of conditions.Several authors have compared the sensitivity of different water-stress indicators, a crucial feature to be considered when determining the usefulness of any indicator for irrigation scheduling.Goldhamer et al. [229] found the following sensitivity ranking for 8-year-old peach trees growing in a lysimeter: MXAWCF > MNSD > MDS > MXSD > Ψ stem = A = Ψ pd = Ψ l , where MXAWCF is the maximum daily available soil-water content fluctuations and A is the net CO 2 assimilation.For similar trees growing in the field, the ranking was MXAWCF > MNSD > MDS > Ψ stem = Ψ l = MXSD = Ψ pd > A. Intrigliolo and Castel [100] found, in plum trees, the following degree of correlation between plant and soil-water status indicators and fruit weight at harvest: Ψ stem ≈ Ψ pd ≈ g s > MDS > SGR > Ψ soil .Considering that g s was much more variable than Ψ pd and Ψ stem , and despite the operational advantages of LVDT for continuous monitoring of plant water status, they concluded that Ψ stem and Ψ pd could be the best plant water-stress indicators in plum.Gallardo et al. [120] observed, for potted pepper plants in a greenhouse, that the signal values were greater for MDS than for Ψ stem but, because of the lower noise values of Ψ stem , the sensitivity index (the signal/noise ratio) was much higher for Ψ stem than for MDS.
Goldhamer et al. [229] demonstrated that, in 8-year-old peach trees, SDV detected stress earlier than Ψ stem , and that the signal strength (Section 2.4) of trunk MDS for detecting water deficit was greater than that of Ψ stem .This last result agrees with findings of Goldhamer and Fereres [119] in well-irrigated almond trees.Moriana and Fereres [123] found that SGR, MXSD, and MNSD were more useful than Ψ stem for an early detection of water stress in young olive trees.However, they did not find differences in MDS between stressed and control trees.These results contrast with those obtained by Intrigliolo and Castel [100,129] in young plum trees, who found that Ψ stem and predawn leaf water potential (Ψ pd ) were better plant water-stress indicators than MDS and SGR.Furthermore, Intrigliolo and Castel [230] found that MDS was more variable than Ψ stem for young plum trees, so that more determinations of MDS than of Ψ stem were needed to estimate plant water status with similar precision.Galindo et al. [231] compared TDV records with midday Ψ stem and g l records in pomegranate trees under different water stress conditions, and found that MDS was the most suitable indicator for irrigation scheduling, because of its high signal: noise ratio, when Ψ stem > −1.67 MPa.For those conditions of null to moderate water stress level, MDS increased in response to Ψ stem Still, for lower values of Ψ stem , MDS decreased.
The examples mentioned above indicate that each method to assess time courses of plant water stress and to schedule irrigation has its potential and limitations, and that its performance depends, to a large extent, on the conditions in which it is applied.Thus, instead of considering a method better than another, the user must choose that method that best fits the orchard conditions.

Reliability
Accounts for the capacity of the sensor and related equipment to perform their required functions under stated conditions for a specified period of time.
All the methods mentioned in Section 2.2 yield reliable WSI.

Robustness
Accounts for the capacity of the sensor and related equipment to cope with variations in their operating environment with minimal damage, alteration, or loss of functionality.
All the sensors and related systems mentioned in Section 2.2 are able to work under field conditions for large periods of time.
Table 4. Requirements for sensors and related equipment (the system), and for the water stress indicator derived from the collected records, to be used for irrigation scheduling in commercial orchards.After Fernández [20].
The system must be inexpensive and easy to install, operate and maintain.
The system must be reliable and robust, capable of working under field conditions for the whole irrigation season.
The system must allow for both automated and continuous collection of clean data and data transmission, i.e., it must be suitable for working properly in electromagnetic-polluted environments and in areas with low cover for data transmission.
The system must have low power requirements (e.g., batteries fed with solar panels).
The water stress indicator derived from the collected records must be highly sensitive, i.e., it must show a high signal: noise ratio.
The indicator must also show an early response to the onset of water stress.
The indicator must be related to a variable of economic importance, such as crop yield or fruit quality.
The indicator, or the raw sensor outputs in case they are used without any further data processing, must be easy to interpret.
If the indicator or raw outputs are not easy to interpret, the system must be provided with an application for visual readouts, graphs, historical records, and other tools to facilitate data interpretation.
The system should be easily implemented with an application for the combined use of the chosen indicator with a weather prediction system.This will improve the user capacity for adjusting the timing and intensity of irrigation under changing weather conditions.
The system should be easily combined with methods to define areas with characteristic water-stress behaviour within the orchard, such as airborne imagery.This allows for precise irrigation in large, highly variable orchards.
The indicator must be suitable for automatic irrigation scheduling and control.In this case, the system should be suitable to be implemented with expert systems, alarms, and other tools for an early detection and lower impact of malfunctions.

Choosing the Right Production Target
As detailed in Section 1, precision irrigation (PI) is intended to improve water use efficiency (WUE) in agriculture.Thus, PI must be capable of providing the production target with the best possible crop water productivity (WP).Now, the concepts of WUE, production target and WP are often misused, partly because of an incorrect use of the terminology and also because of a lack of understanding of the processes behind each.The concept of water use efficiency in agriculture was addressed in detail by Hsiao et al. [232].They considered eight different efficiency steps, from the water reservoir to the harvested yield.The eight steps must each be considered in order to calculate the overall WUE.Precision irrigation relies on the right choice of the irrigation system, the irrigation strategy and the scheduling irrigation method, but soil has a large impact on all the efficiency steps, even on those that at a first sight depend on the plant physiology or metabolism only, such as the assimilation efficiency.Thus, reduced irrigation can cause a reduction in stomatal conductance (g s ) without affecting net CO 2 assimilation (A), which will improve the assimilation efficiency.In olive, for instance, the g s vs.A relationship shows that g s can decrease from maximum recorded values of about 0.4 mol m −2 s −1 to nearly 0.2 mol m −2 s −1 without a reduction in A, which remains close to 20 µmol m −2 s −1 for that g s range [233].
Part of the confusion when addressing the effect of irrigation management on water use efficiency (WUE) comes from a lack of consensus on the terminology.Thus, Steduto et al. [234] used photosynthetic water productivity for what Hsiao et al. [232] called assimilation efficiency, and Perry [235] used productivity of transpiration for the transpiration efficiency of Hsiao et al. [232].Researchers from different disciplines often disagree on the meaning of WUE.Thus, the fraction of water supplied that moves beyond the rooting depth (drainage or deep percolation) is usually considered as a loss by agronomists, but not by hydrologists, who usually consider it as a contribution to the recharge of the aquifer [235].In addition, WUE has different meanings depending on the temporal (from seconds to years) or spatial scale (from the leaf to the basin) to which it is applied.Another source of confusion comes from the difficulty of determining WUE accurately.Thus, at the crop level, WUE is defined as the yield (Y) per unit of water used by the crop, or crop evapotranspiration (ET), i.e., WUE = Y/ET (8) Determining ET properly is not easy, since ET = P + I − i ± R ± ∆S ± F B ± F L (9) where P = precipitation, I = irrigation, i = water intercepted by the canopy, R = run off, ∆S = difference of water stored in the soil between the beginning and the end of the considered period, F B = fluxes of water at the bottom of root zone, and F L = fluxes of water at the laterals of root zone.Thus, many authors use ET = P + I (10) instead of Equation ( 9) to calculate WUE, while others consider more components of the equation.This leads to difficulties in interpreting and comparing WUE data given by different authors [235].Precision irrigation in arid and semi-arid areas implies deficit irrigation (DI), and peculiarities related to DI must be taken into account to determine if it is a wise choice for a production target.This implies a precise knowledge of the concepts of water use efficiency and crop water productivity and of the influence of DI on crop performance.Since the early 2000s, many authors have used the concept of crop water productivity (WP), defined by Molden [236] as the yield or net income per unit of water used in ET.Actually, some consider that WUE and WP are synonymous and equal to the ratio of the mass marketable yield (Y) to the volume of water used by the crop, ET [237,238].Others, however, suggest that WUE should be used when referring to the water performance of plants and crops to produce assimilates, biomass or harvestable yield, reserving WP to express the quantity of product or service produced by a given amount of water used [239].That implies that WP does not include the physiological meaning that WUE has.For more details on differences between WUE and WP, see Bouman [240], Ali and Talukder [241] and Flexas et al. [242].It has to be taken into account that the aim of most growers is not to produce the maximum mass marketable yield per unit of water used by the crop, but to get the greatest net income.As an example, consider a case in which DI is applied to a crop growing in a soil with a high amount of stored water.The crop is forced to use water stored in the soil because of reduced irrigation, but ET will be maintained if enough stored water is available.In this situation the mass marketable yield to the volume of water used by the crop will not change as compared to a situation of full irrigation, but the farmer will save money because of the reduced irrigation.Now, if the soil water is insufficient to meet the crop demand, ET will be reduced and the yield negatively affected, but that will not necessarily mean a reduction in WP.Thus, if the crop is a super high-density olive crop for oil production, for instance, the quality of the oil will be better and plant vigor will be controlled.The latter will reduce costs related to phytosanitary treatments and pruning, and will ensure a long productive life of the orchard by reducing problems derived from competition for light among trees.Therefore, deficit irrigation in this type of orchard may lead to an improved WP in the medium-long term, as compared to full irrigation, despite yield reductions.
Methods to schedule irrigation such as those included in this work are infrequently used in commercial orchards because most growers rarely make a detailed analysis of the expected net incomes when managing irrigation in one way or another.Current technologies for economic analyses of water use in agriculture provide irrigation specialists with a wide variety of tools to choose the best irrigation approach and to achieve a sustainable balance between production and environmental impact [243][244][245].Such analyses are particularly important in a context of precision irrigation, to obtain the maximum benefits of the involved technology.

Concluding Remarks
Precision irrigation is an approach that, if properly managed, can lead to substantial water savings in agriculture.It is especially efficient in woody crops in arid and semi-arid areas, when not only water saving, but also improved yield quality and reduction of excessive growth, are pursued.Electronic and communication products are facilitating a wider use of telematics in agriculture, by providing cheaper sensors and related systems, and more efficient communication networks.Likely, this will contribute significantly to an increasing popularity of precision irrigation.Still, the irrigation specialist must be properly trained on the crop response to water stress and on new methods and technologies related to precision irrigation.He/she must be aware of the advantages and disadvantages of the existing methods and technologies for precision irrigation, for a proper choice of those better fitting specific farm or orchard conditions.The wise choice of the production target is also important, especially in a context of deficit irrigation.This is particularly crucial for woody crops, where the choice of the production target may be far more complicated than just achieving the greatest biomass per unit of water consumed by the crop.Finally, the decision process within a framework of precision irrigation involves choices that can be expensive to implement, and that can have a great impact on the final profit.In that context, detailed economic analyses are compulsory for achieving maximum profitability.

Figure 1 .
Figure 1.Regulated deficit irrigation strategy for a hedgerow olive orchard with 1667 trees per ha in southwest Spain.The production target was to achieve the most profitable balance between oil yield and oil quality at the same time that a long productive life of the orchard was ensured by reducing problems derived from competition for light among trees.SHD = super-high density; IN = seasonal irrigation needs; ETc = crop evapotranspiration; Pe = effective precipitation; IA = seasonal irrigation amount; AW = available soil water; and i.e. = irrigation event.After Fernández et al. [6] and Padilla-Díaz et al. [7].

Figure 1 .
Figure 1.Regulated deficit irrigation strategy for a hedgerow olive orchard with 1667 trees per ha in southwest Spain.The production target was to achieve the most profitable balance between oil yield and oil quality at the same time that a long productive life of the orchard was ensured by reducing problems derived from competition for light among trees.SHD = super-high density; IN = seasonal irrigation needs; ETc = crop evapotranspiration; Pe = effective precipitation; IA = seasonal irrigation amount; AW = available soil water; and i.e. = irrigation event.After Fernández et al. [6] and Padilla-Díaz et al. [7].

Figure 3 .
Figure 3. Scholander chambers for measuring approximate water potential of plant tissue.A model by Soilmoisture Equipment Corp., Santa Barbara, CA (USA), implemented with a binocular stereo microscope and a cold light illuminator (left), and a model by PMS Instrument Company, Albany, OR (USA), implemented with a binocular stereo microscope and a digital manometer (right).

Figure 3 .
Figure 3. Scholander chambers for measuring approximate water potential of plant tissue.A model by Soilmoisture Equipment Corp., Santa Barbara, CA (USA), implemented with a binocular stereo microscope and a cold light illuminator (left), and a model by PMS Instrument Company, Albany, OR (USA), implemented with a binocular stereo microscope and a digital manometer (right).

Figure 4 .
Figure 4. Diurnal courses of both stomatal conductance (gs) and leaf water potential (Ψl) measured in 39-year-old 'Manzanilla de Sevilla' olive trees at 7 m × 5 m spacing in 2007.On 28 August, the first gs measurements are missing because of a problem with the gas analyser.Both for 24 July and 28 August, two clear-sky days of the irrigation season, measurements were taken in trees under three water treatments: (1) Dry-farming, with rainfall as the only source of water supply; (2) Pond, in which the trees were irrigated with a grid of pipes with a 2 L h −1 dripper every 0.4 m × 0.4 m.The grid covered a surface of 8 m × 6 m, with the tree in the middle, enough for keeping non-limiting soil water conditions in the whole root zone, all throughout the irrigation season; and (3) Localized, in which trees were irrigated daily to replace the crop evapotranspiration, with a lateral per tree row with five 3 L h −1 drippers per tree, 1 m apart.With this system some roots were left in drying soil.Differences in gs between the Pond and Localized trees were recorded on both days.Values of Ψl, however, showed that the trees of both treatments had similar water status.Mean ± SE, n = 6.No asterisk means no significant differences; **, *** and **** indicate significant differences at p ≤ 0.01,

Figure 4 .
Figure 4. Diurnal courses of both stomatal conductance (g s ) and leaf water potential (Ψ l ) measured in 39-year-old 'Manzanilla de Sevilla' olive trees at 7 m × 5 m spacing in 2007.On 28 August, the first g s measurements are missing because of a problem with the gas analyser.Both for 24 July and 28 August, two clear-sky days of the irrigation season, measurements were taken in trees under three water treatments: (1) Dry-farming, with rainfall as the only source of water supply; (2) Pond, in which the trees were irrigated with a grid of pipes with a 2 L h −1 dripper every 0.4 m × 0.4 m.The grid covered

Figure 4 .
Figure 4. Diurnal courses of both stomatal conductance (gs) and leaf water potential (Ψl) measured in 39-year-old 'Manzanilla de Sevilla' olive trees at 7 m × 5 m spacing in 2007.On 28 August, the first gs measurements are missing because of a problem with the gas analyser.Both for 24 July and 28 August, two clear-sky days of the irrigation season, measurements were taken in trees under three water treatments: (1) Dry-farming, with rainfall as the only source of water supply; (2) Pond, in which the trees were irrigated with a grid of pipes with a 2 L h −1 dripper every 0.4 m × 0.4 m.The grid covered a surface of 8 m × 6 m, with the tree in the middle, enough for keeping non-limiting soil water conditions in the whole root zone, all throughout the irrigation season; and (3) Localized, in which trees were irrigated daily to replace the crop evapotranspiration, with a lateral per tree row with five 3 L h −1 drippers per tree, 1 m apart.With this system some roots were left in drying soil.Differences in gs between the Pond and Localized trees were recorded on both days.Values of Ψl, however, showed that the trees of both treatments had similar water status.Mean ± SE, n = 6.No asterisk means no significant differences; **, *** and **** indicate significant differences at p ≤ 0.01, 0.001 and 0.0001, respectively.See Fernández et al.[53] for details.

Figure 5 .
Figure 5. Tree transpiration (Ep) determined by Ohm's law electrical analogue (Equation (1) in the text) in an orchard with 39-year-old 'Manzanilla de Sevilla' olive trees at 7 m × 5 m spacing, under two water treatments leading to contrasting soil water conditions.REW = relative extractable water in the soil; Ψs = soil water potential; Ψl = leaf water potential; and K = hydraulic conductivity.See Fernández et al. [53] for details.2.1.3.Thermal Sensing Measurements of canopy temperature (Tc) to assess water stress began some 50 years ago [54].It was not until the development of the crop water stress index (CWSI, see below), however, that the

Figure 5 .
Figure 5. Tree transpiration (E p ) determined by Ohm's law electrical analogue (Equation (1) in the text) in an orchard with 39-year-old 'Manzanilla de Sevilla' olive trees at 7 m × 5 m spacing, under two water treatments leading to contrasting soil water conditions.REW = relative extractable water in the soil; Ψs = soil water potential; Ψ l = leaf water potential; and K = hydraulic conductivity.See Fernández et al. [53] for details.

Figure 6 .
Figure 6.Images corresponding to the work by Egea et al. [65] in which a thermal infrared (TIR) camera (Tau 2 324, FLIR Systems, Inc., Wilsonville, OR, USA) was mounted on a multirotor RPAS (Remote Piloted Aerial System) model Phantom 2 (SZ DJI Technology Co., Ltd., Shenzhen, China) for thermal imagery acquisition in a high hedgerow olive orchard with 1667 trees per ha (left).Several 0.4 m × 0.5 m black plastic panels were used as a hot reference (central).Images were taken at 20 m above ground and at solar noon of two fully irrigated plots (purple and blue colors) and two deficit-irrigated plots (yellow and orange colors) (right).

Figure 6 .
Figure 6.Images corresponding to the work by Egea et al. [65] in which a thermal infrared (TIR) camera (Tau 2 324, FLIR Systems, Inc., Wilsonville, OR, USA) was mounted on a multirotor RPAS (Remote Piloted Aerial System) model Phantom 2 (SZ DJI Technology Co., Ltd., Shenzhen, China) for thermal imagery acquisition in a high hedgerow olive orchard with 1667 trees per ha (left).Several 0.4 m × 0.5 m black plastic panels were used as a hot reference (central).Images were taken at 20 m above ground and at solar noon of two fully irrigated plots (purple and blue colors) and two deficit-irrigated plots (yellow and orange colors) (right).

Horticulturae 2017, 3 , 35 14 of 38 Figure 7 .
Figure 7. System used by the author to measure sap flow in olive trees with the compensation heat pulse method.It consisted of a solar panel and weather-proof boxes for the electronics (upper box) and battery (lower box) (left).Also shown are sap flow probes inserted into the trunk and a main root of olive trees (right).

Figure 7 .
Figure 7. System used by the author to measure sap flow in olive trees with the compensation heat pulse method.It consisted of a solar panel and weather-proof boxes for the electronics (upper box) and battery (lower box) (left).Also shown are sap flow probes inserted into the trunk and a main root of olive trees (right).

Figure 8 .
Figure 8. Two different systems for the automatic recording and data transmission of trunk diameter variations.The system on the left consists of LVDT (linear variable differential transformer) dendrometers connected to a Campbell CR1000 data logger (Logan, UT, USA).On the right, a Verdtech station with Plantsens radial dendrometers (Verdtech un Nuevo Campo S.A., Lepe, Spain) is shown, along with a C-Probe (AquaSpy, Inc., San Diego, CA, USA) for the measurement of the soil volumetric water content, two Rain-O-Matic tipping-bucket gauges (Pronamic Co. Ltd, Sikeborg, Denmark), one to record the water supplied by the irrigation system and the other for the precipitation amounts; a combined sensor of temperature and humidity of the air (Vaisala Oyj, Helsinki, Finland) and an addWAVEA733GSM remote telemetry unit (Adcaon Telemetry, Klosterneuburg, Austria).

Figure 8 .
Figure 8. Two different systems for the automatic recording and data transmission of trunk diameter variations.The system on the left consists of LVDT (linear variable differential transformer) dendrometers connected to a Campbell CR1000 data logger (Logan, UT, USA).On the right, a Verdtech station with Plantsens radial dendrometers (Verdtech un Nuevo Campo S.A., Lepe, Spain) is shown, along with a C-Probe (AquaSpy, Inc., San Diego, CA, USA) for the measurement of the soil volumetric water content, two Rain-O-Matic tipping-bucket gauges (Pronamic Co. Ltd, Sikeborg, Denmark), one to record the water supplied by the irrigation system and the other for the precipitation amounts; a combined sensor of temperature and humidity of the air (Vaisala Oyj, Helsinki, Finland) and an addWAVEA733GSM remote telemetry unit (Adcaon Telemetry, Klosterneuburg, Austria).

Figure 10 .
Figure 10.A TDR probe installed in the trunk of an olive tree for volumetric water content-related measurements (left).The photo was taken during a joint experiment of the author with Dr. Arie Nadler (Institute of Soil, Water, and Environmental Sciences, ARO, Rishon LeZion, Israel), who manufactured the probe.A probe for electric potential-related measurements in the stem of a young fruit-tree (right), manufactured by Dr. Luis Gurovich (Department of Fruit Science, Pontificia Universidad Católica de Chile, Santiago, Chile).

Figure 10 .
Figure 10.A TDR probe installed in the trunk of an olive tree for volumetric water content-related measurements (left).The photo was taken during a joint experiment of the author with Dr. Arie Nadler (Institute of Soil, Water, and Environmental Sciences, ARO, Rishon LeZion, Israel), who manufactured the probe.A probe for electric potential-related measurements in the stem of a young fruit-tree (right), manufactured by Dr. Luis Gurovich (Department of Fruit Science, Pontificia Universidad Católica de Chile, Santiago, Chile).
During the irrigation season, plant-based records are continuously taken in the same trees earlier used to determine the Signal ref values.The actual signal values (Signal actual ) are derived from those records.The Signal actual value must be kept as close as possible to the Signal target value by frequently adjusting the irrigation amount (IA).Most authors compared Signal actual to Signal target every 2-3 days, and varied IA by ±10-20% if the two values differed.If Signal actual > Signal target , IA is raised by 10%.A greater percentage, e.g., 20%, has sometimes been used, especially early in the season, due to uncertainty in determining the initial application amounts.This would allow faster convergence of the applied water amounts and tree water requirements.If Signal actual < Signal target , IA is lowered by 10-20%.

Table 2 .
Most-used plant-based measurements and related water stress indicators for irrigation scheduling.
N µmol m −2 s −1Net amount of CO 2 assimilated per square meter of leaf and per second at the time of the measurement.
l or Ψ stem Ψ l or Ψ stem MPa Leaf or canopy spectral measurements are correlated with values of Ψ l or Ψ stem made with a Scholander-type chamber, to derive an observed Ψ vs. predicted Ψ relationship.

Table 3 .
[113]cteristics that must be analysed to assess the suitability of any water stress indicator for irrigation scheduling (see Fernández and Cuevas[113]for details).