An Analysis of the Factors Influencing Cadmium Removal in Aquatic Environments by Chlorella vulgaris -Derived Solids

: Chlorella vulgaris is an inexpensive microalga that could be employed for environmental remediation, but further investigations are needed to assess its suitability and optimal treatment methodology. With this aim in mind, this study focused on the raw biomass and the biochar and hydrochar obtained from it, analyzing their physicochemical properties and testing them to capture cadmium from an aqueous environment. The adsorption/absorption tests assessed the effect of adsorbent dosage, pH, Cd concentration, and contact time, and the results were analyzed through a structural equation model. Biochar and hydrochar performed similarly and better than the raw biomass, with the highest Cd removal observed at an adsorbent dosage of 0.8 g L − 1 , an initial concentration of Cd solution of 30 mg L − 1 , a pH of 6, and a contact time of 30 min. The adsorption isotherm data for Cd could be well-described by the Langmuir and Temkin models. The results from the structural equation modeling revealed that the variables material type, dosage, and concentration all contributed to Cd removal in water, with time mediating these effects.


Introduction
Heavy metal pollution in water is a significant environmental concern [1,2].Metals or metalloids with a density of 3.5-7.0g cm −3 are considered toxic, even at low concentrations [3,4].Heavy metals that exceed maximum acceptable concentrations, according to the regulatory agencies, are harmful to the environment and must be removed through appropriate processing [5].Cadmium (Cd) is one of the most toxic heavy metals and hazardous environmental pollutants, highly noxious to aquatic organisms, even at low concentrations, and carcinogenic to humans [6].Although the definition of "heavy metal" is somehow debated [7], Cd fits several criteria, both in terms of its atomic number (48) and toxicity [8].Cadmium contamination in aquatic environments can have adverse effects on the ecosystems themselves and can easily affect the human food chain [9,10].This problem is not limited to specific regions but is a global menace [11]; various governments and agencies have established regulatory limits.The urgency to study methods to monitor and control Cd levels in water sources is, thus, evident.Numerous methods exist to remove heavy metals from water, including ion exchange, membrane filtration, adsorption, electrochemical precipitation, and chemical precipitation.Each method has intrinsic advantages and limitations that determine its applicability [12].
Biochar and hydrochar are two important types of solid materials derived from biomass.They can be employed as sorbents, catalysts, and precursors for activated carbon and other functional materials [13,14].Pyrolysis biochar is the solid product of the thermochemical degradation of biomass at high temperatures (generally 600 • C) in the presence of little or no oxygen and under dry or semi-dry conditions.Biochar is a semicombustible charcoal, and its physical, chemical, and structural properties (stability, pore size, dispersion, cation exchange capacity, ash fraction, specific surface area (SSA), and mineral content) largely depend on the type of feedstock and production conditions (heating rate, pyrolysis duration, oxidation condition, and temperature) [15].Hydrochar is a dark solid with lignite-like properties that is produced by heating biomass submerged in liquid water at a pressure of 10-50 bar and a temperature of 180-250 • C without oxygen.The process used to produce hydrochar is called hydrothermal carbonization (HTC) [16].Hydrochar offers several advantages over biochar, including higher yield, lower acidity, and lower energy input [17].Additionally, since HTC occurs in liquid water, there is no need to dry the biomass, making it particularly suitable for wet residues [18].Both biochar and hydrochar typically have modest SSAs, but these can be enhanced through further activation steps to meet the requirements for activated carbons [19].
Algae are photosynthetic organisms with various ecological applications.Their ability to store nutrients such as phosphorus and nitrogen, their excellent adsorption/absorption capacity for heavy metals, and their high photosynthetic efficiency make them highly suitable for application in aquatic environments.Algae are economically viable for biochar production because they do not require arable soil or additional nutrients.Several studies have demonstrated that biochar produced from algae is a clean material that enhances carbon sequestration and bioremediation [20].Algal biochar has proven capabilities as an adsorbent/adsorbent for heavy metal ions, such as Cu, Cd, and Zn, from aqueous solutions [21,22].Among the various algal species, Chlorella vulgaris (CV) often stands out; it is a microscopic organism measuring 2-10 µm in size and has a structure comparable to that of higher plants.CV growth occurs through simple asexual reproduction.This microalga is ideal for industrial production due to its resistance to harsh conditions and disturbances.It can also be used to treat agricultural, industrial, and domestic wastewater [23] or to produce higher-value products, such as bioplastics [24,25].
Producing adsorbents, such as activated carbons, usually involves high temperatures and expensive (and possibly non-renewable) feedstocks.Thus, it is vital to develop lowcost and effective adsorbents using alternative technologies and cheap materials to meet the increasing demand.One approach for this purpose is to use waste as a source of inexpensive and readily available raw materials to produce adsorbents.Overall, studying biochar and hydrochar derived from CV for the removal of heavy metals is valuable for developing sustainable solutions to address environmental pollution while exploring the potential of these materials in various applications.However, no comprehensive study has been conducted so far to compare hydrochar and biochar produced from CV for removing heavy metals from water.Moreover, modeling and categorizing the factors influencing cadmium removal in water using structural equation models has often been neglected.Hence, given the significance of Cd contamination in water, this study aims to accomplish two objectives: (1) to examine the impact of three types of algal biomass materials, namely raw algal biomass and the biochar and hydrochar derived from it, and (2) to model and categorize the influential factors affecting cadmium removal in water using the structural equation model.It shall be noted that the mechanism of Cd cation capture is complex and not completely established [26].Most likely, it involves more than one phenomenon, including the formation of ionic bonds with ion exchange sites.In this framework, the term "adsorption" may not be entirely adequate to describe the present observations; nonetheless, we decided to employ it for the sake of conciseness.

CV and Derived Materials
The CV algae stock was prepared from the algae culture laboratory of Organic Algae Co.The stock was stored in vitro at 25 • C for 12 h in light and 12 h in the dark (2500 lux).F/2 medium was used for microalgae culture.Table 1 shows the chemical composition of the culture medium used.The culture steps were performed in clean conditions using a separate and completely isolated room.The initial growth period of microalgae was 7 days.When the growth reached the logarithmic growth phase, they were transferred to a larger container with fresh culture medium added.After a two-week growth period, biomass was collected.The algal biomass was washed five times with distilled water to remove salts, then dried in an oven at 40 • C and sieved.For the preparation of the biochar and hydrochar, this material was then crushed in a mill and passed through a 1 mm sieve.The biochar was obtained by placing samples in an electric oven at 450 • C for 120 min, with inert conditions being achieved through a flow of nitrogen.The hydrochar was instead obtained starting from 40 g of algal biomass and 310 mL of distilled water.Following the procedure by Fang et al. [16], the mixture was placed into a sealed stainless-steel pot, which was heated to 250 • C on a hot plate and maintained at this temperature for 6 h.Subsequently, the pot was left to cool down to room temperature.The resulting hydrochar was isolated through filtration using 0.45 µm filter paper (Whatman), then washed for 1 h by immersing it in tap water followed by a 10 min rinse in distilled water.Finally, it was oven-dried for 24 h at 70 • C. Each experiment in this study was repeated three times.The yield of the biochar and hydrochar was calculated as the ratio between the mass of the dried recovered material and the initial mass of the dry biomass.To prepare the culture medium solution for the growth of CV, 2 mL of solutions A and B and 1 mL of solutions C and D were added in 1 L of water.

Materials Characterization
The three materials were subjected to various experimental analyses to determine their properties, with each analysis being repeated at least twice.The investigated properties were: • pH and electrical conductivity (EC): Measured after the samples had been put in deionized water (with a 1/10 mass ratio) for 24 h on a reciprocating shaker at 20 • C.Then, pH value and electrical conductivity at 20 • C were measured according to the ASTM 2866-D standard method, employing an EYELA pH meter and 4320-JENWAY conductivity meter, respectively; • Ash content: Obtained by keeping the samples at 730 • C for 8 h in a muffle furnace; the obtained ashes were then weighed, and their content was calculated by dividing it by the initial dry mass of the material; • Volatile matter content: Measured according to ISO 562-2010 [28].One gram of each sample was put into a porcelain crucible.Samples were heated via a furnace at • C for 10 min in nitrogen flow, and after cooling, the final mass of the samples was weighed.The amount of the volatilized substance was calculated as the relative weight difference before and after the treatment; • Ultimate analysis: The measurement of carbon (C), hydrogen (H), nitrogen (N), and sulfur (S) mass fractions within the samples was performed using a Thermo Finnigan elemental analyzer (FlashEA 1112 series).Oxygen was instead calculated by the difference in the mass fractions of the other elements and ash.Employing the element mass fractions, the products' gross calorific value (GCV) was obtained through the equation proposed by Friedl et al. [29]: GCV = 3.55C

•
Surface properties: The morphology of the samples was investigated using the FESEM-EDX Inspect 24 (ZEISS Sigma 300, Oberkochen, Germany).FESEM testing was conducted to determine the surface and pore patterns of the products.The surface functional groups of activated carbon were analyzed using an FTIR spectrophotometer (Nicolet is 10/Thermo Scientific, Waltham, MA, USA).

Adsorption Experiments
The Cd adsorption tests were conducted using a batch equilibration technique at room temperature for triplicate samples.Stock solutions of Cd (1000 mg L −1 ) were prepared by dissolving CdCl 2 •2.5H 2 O (Merck, Darmstadt, Germany) in double-distilled water.For the adsorption kinetics, 0.4 g of biochar/hydrochar/algae biomass was added to a 50 mL solution containing 20 mg L −1 of Cd as CdCl 2 .The solution was then agitated at 150 rpm on a reciprocating shaker.Finally, the concentration of Cd in the solutions was determined using atomic absorption spectrometry (AAS, ZEEnit 700P, Analytik Jena, Jena, Germany).The effect of the dosage of adsorbents on the removal of Cd (20 mg L −1 ) from the water was investigated by mixing 50 mL of Cd solution (20 mg L −1 ) at room temperature with various amounts of each sample (0.1-2 g L −1 ) for 30 min.The effect of different pH values (2-9) on the removal of Cd was also studied.The percentage removal of Cd was calculated based on the difference between the equilibrium concentration (C e ) and initial concentration (C 0 ) of Cd in solution (mg L −1 ).The equilibrium adsorption amounts (Q e , mg g −1 ) of Cd onto biochar, hydrochar, and algae biomass, as well as the adsorption efficiencies (%), were calculated using Equations ( 1) and (2), respectively.

Qe
where V is the volume of the solution (mL), and M is the mass of the adsorbent (g).

Isotherm Study
In this study, three important and widely employed isotherms are used to provide a mathematical description of Cd removal at equilibrium conditions.The adsorption data were fitted to the logarithmic form of the Langmuir (Equation (3)), Freundlich (Equation (4)), and Temkin (Equation ( 5)) equations/models.These models were developed for adsorption, which may indeed represent only a step in the complex removal mechanism that takes place when Cd ions interact with a carbon-based adsorption material.Nonetheless, these models are often applied for Cd ions removal [30][31][32][33] because they represent an intuitive and easy-to-use means to discriminate, at least at a preliminary level, between different interaction/adsorption mechanisms between removed material (Cd ions in the present case) and adsorbent material.The Langmuir isotherm [34] is represented by Equation ( 3) where C e is the equilibrium concentration (mg L −1 ), q e is the equilibrium adsorption value (mg g −1 ), q max is the maximum adsorption amount (mg g −1 ), and b (L mg −1 ) is the Langmuir constant.The Langmuir equation shows the maximum adsorption on absorbent surfaces (q max ).Compared to other isotherm equations, the Langmuir equation provides more information about the adsorption of elements [35].
The Freundlich isotherm [36] was calculated by Equation (4): where n and k f (L mg −1 ) are the Freundlich constants, corresponding to the biosorption capacity and surface heterogeneity, respectively.The Freundlich equation is considered better than the Langmuir equation because, in addition to being simple, it is based on more realistic assumptions.The Freundlich equation can explain the non-ideal adsorption on heterogeneous surfaces and the adsorption of multiple layers well.The Freundlich equation can be justified with the assumption that the decrease in adsorption energy with increasing surface coverage is due to the uniformity of the absorbing surfaces [37].The Temkin isotherm [38] is given as Equation ( 5): In which b T is the Temkin constant, and k T is the constant of equilibrium of Temkin (L g −1 ).The ratio RT/b T is associated with the adsorption heat (J mol −1 ), R is the perfect gas constant (8.314J mol K −1 ), and T is the temperature (K).

Structural Equation Modeling (SEM)
SEM is a statistical technique that allows modeling and evaluating complex relationships among different variables.It is a multivariate statistical method combining factor analysis and multiple regression to test and estimate the relationships between observed and unobservable variables.The key components of SEM include:

•
Latent variables: These are variables that cannot be directly observed but are inferred from a set of observed variables that are related to them.Latent variables are also known as constructs or factors; • SEM allows researchers to test complex hypotheses, explore the underlying structure of the data, and evaluate the fit of the proposed models to the data.It also provides estimates of the strength and significance of the relationships between variables and allows for the inclusion of measurement errors in the analysis.

Properties of CV and Its Biochar and Hydrochar
Table 2 presents the main results from the characterization of CV and the biochar and hydrochar obtained from it.The highest yield was observed for hydrochar, which is often reported in the literature and ascribed to the lower severity of the HTC process.The results of Binda et al. [39] also showed a lower yield for the biochar from CV; the yields obtained in this study are higher than theirs.In terms of composition, the findings revealed that biomass had the lowest carbon content, whereas hydrochar had the highest carbon content.Biochar exhibited the minimum hydrogen value, while biomass had the maximum hydrogen value.Regarding nitrogen, biomass showed the highest value, whereas hydrochar had the lowest value.Furthermore, biomass yielded the maximum sulfur value, whereas hydrochar had the minimum sulfur value.The results indicate that hydrothermal processes resulted in a significant increase in carbon and a decrease in hydrogen, which aligned with the findings of Tsarpali et al. [40].During hydrothermal carbonization, condensation and aromatization reactions occurred, leading to an enrichment of carbon in the hydrochar [41].Additionally, biochar prepared at less than 500 • C contained more dissolved organic C and O functional groups at relatively low C/N ratios, making it more effective for removing inorganic contaminants.Dehydration and methanation reactions during pyrolysis have a significant impact on the elemental composition and ratio.The H/C and O/C atomic ratios are indicators of biochar stability.These ratios are used to measure aromaticity and maturation [42].Higher levels of carbonization and a lack of oxygen and hydrogencontaining functional groups (such as carboxyl, hydroxyl, etc.) at higher temperatures result in lower H/C and O/C ratios, which are signs that the surface of the material is more aromatic and less hydrophilic [43].Changes in O/C and H/C atomic ratios are commonly depicted on Van Krevelen diagrams, allowing comparison and prediction of the combustion properties [44].These changes allow for evaluating the degree of deoxygenation of biomass through decarboxylation or dehydration.Figure 1 illustrates that pyrolysis and hydrothermal carbonization lead to a probable increase in aromaticity, as evidenced by a decrease in O/C and H/C ratios compared to the values of the raw materials.The degree of carbonization observed in both biochar and hydrochar materials was similar.The molar ratios of H/C and O/C for biomass were 1.83 and 0.45, respectively, which differed from those for brown coal and lignite.Pyrolysis and HTC increase the ash content due to the removal of volatiles and the accumulation of inorganic fractions from algal biomass.During HTC, some soluble mineral salts may dissolve, which explains the lower ash content of hydrochar.A high ash content in algae biochar can enhance adsorption [45].The ash on the char surface consists of various inorganic compounds that C 2024, 10, 2 7 of 21 may be exchanged through the adsorption process of Cd; thus, cation exchange could be a plausible mechanism for Cd adsorption on char [46].removal of volatiles and the accumulation of inorganic fractions from algal biomass.Du ing HTC, some soluble mineral salts may dissolve, which explains the lower ash conte of hydrochar.A high ash content in algae biochar can enhance adsorption [45].The ash the char surface consists of various inorganic compounds that may be exchanged throu the adsorption process of Cd; thus, cation exchange could be a plausible mechanism f Cd adsorption on char [46].The pyrolysis and HTC treatment also changed other material properties in accor ance with the existing literature.Most notably, the GCV increases in both cases, reachi values more similar to those of lignocellulosic biomass, while the volatile matter conte decreases.Volatile matter content characterizes the degree of thermal conversion for b char and hydrochar, which is influenced by their chemical composition and producti conditions [47].Chaiwong et al. [48] observed a similar phenomenon when studying t proximate analysis of algal biochar (Cladophora).Their results indicated that algal b char had lower volatile matter content (35.5%) compared to the parent raw macroal (60.6%).Furthermore, this study found that carbon content increased from 28.8% in t feedstock to 51.1% in algal biochar, while ash content increased from 33.4% in Cladopho algae as feedstock to 38.8% in algal biochar.
Finally, the specific surface area also increased after both treatments but still mained much lower than that of activated carbons (around 500 m 2 g −1 ), indicating tha further physical or chemical activation step would be necessary to enhance it.Howev the average pore size differed among all three materials.The increase in mean pore dia eter with increasing temperature is attributed to the evaporation of water and organ compounds from biochar, which is caused by the presence of numerous small pores on surface [49].Interestingly, hydrochar is produced at lower temperatures (thus oft The pyrolysis and HTC treatment also changed other material properties in accordance with the existing literature.Most notably, the GCV increases in both cases, reaching values more similar to those of lignocellulosic biomass, while the volatile matter content decreases.Volatile matter content characterizes the degree of thermal conversion for biochar and hydrochar, which is influenced by their chemical composition and production conditions [47].Chaiwong et al. [48] observed a similar phenomenon when studying the proximate analysis of algal biochar (Cladophora).Their results indicated that algal biochar had lower volatile matter content (35.5%) compared to the parent raw macroalga (60.6%).Furthermore, this study found that carbon content increased from 28.8% in the feedstock to 51.1% in algal biochar, while ash content increased from 33.4% in Cladophora algae as feedstock to 38.8% in algal biochar.
Finally, the specific surface area also increased after both treatments but still remained much lower than that of activated carbons (around 500 m 2 g −1 ), indicating that a further physical or chemical activation step would be necessary to enhance it.However, the average pore size differed among all three materials.The increase in mean pore diameter with increasing temperature is attributed to the evaporation of water and organic compounds from biochar, which is caused by the presence of numerous small pores on its surface [49].Interestingly, hydrochar is produced at lower temperatures (thus often requiring less energy) and contains O-rich functional groups (carboxyl, carbonyl, hydroxyl, and phenolic hydroxyl) that may improve metal absorption [50].Additionally, the raw materials used for the hydrothermal carbonization reaction influence surface and porosity characteristics, which aligns with the findings of Bird et al. [51], where low surface area was reported for all algal biochar production temperatures.
Biochar has the highest pH (7.9) and EC (4.5 dS m −1 ) values, while hydrochar has the lowest pH value (6.7).Biochar is typically alkaline due to its high concentration of alkaline elements, whereas hydrochar is often acidic due to its lower concentration of alkaline elements and the presence of acidic compounds in its structure [52].The high pH of biochar may be ascribed to basic cations (such as Ca and Mg) being released at high temperatures during the pyrolysis process [53].A study by Sun et al. [54] reported a strong positive correlation between ash content and biochar pH, with higher pH observed in biochar with high ash content.However, hydrochar surfaces often contain acidic functional groups due to the reaction mechanism of hydrothermal carbonization.
Figure 2 shows FTIR spectra that are useful for gathering information about the various functional groups present on the surface of materials.The FTIR spectra of biomass, hydrochar, and biochar exhibited a similar trend, with biochar displaying fewer peaks compared to biomass.However, the peaks in biochar were sharper and taller.The emergence of new peaks in biochar can be attributed to volatiles being released and chemical bonds being broken during pyrolysis.Similarly to biochar, hydrochar also displayed sharper peaks.The functional groups present on the surface of biochar are crucial for effective sorption and electron transfer, which aid in contaminant removal [54].Additionally, the hydroxyl and carboxyl groups on the surface of each material play a significant role in capturing metal ions from solutions [55].The peak observed at 3415 cm −1 in all samples indicated O-H tensile vibrations, suggesting the presence of phenols, alcohols, or carboxylic acid.Table 3 reports the tentative assignments.The peaks at 2853 cm −1 in biochar and 2874 cm −1 in hydrochar correspond to asymmetric and symmetric CH 2 bonds.In biochar, sharp peaks at 1420 and 1416 cm −1 confirm the presence of C-H groups in alkanes, which were weaker in hydrochar and biomass.Absorption bands between 1600 and 1800 cm −1 indicate the presence of aldehyde/ketone compounds that varied in size among all three materials.The absorption bands at 1600-1700 cm −1 suggest stretching vibrations for C=O and C=C bonds found in carboxyl, carbonyl, or ester compounds.These oxygen-containing functional groups with acidic properties may facilitate heavy metal adsorption.Sharp peaks between 1300 and 1000 cm −1 were attributed to C-O-C asymmetric bonds, while the sharp peaks at 872 and 873 cm −1 correspond to the C-O group in carbonate.
These findings were accompanied by a reduction in volatiles in the proximate analysis of biochar and hydrochar.The presence of oxygenated functional groups and a high O/C atomic ratio in the two chars indicate the potential application of these compounds in adsorption studies [50].According to the results, some biomass peaks disappeared in the biochar spectra, while the release of volatiles and chemical bond breakage during the pyrolysis reaction caused new peaks to appear.Regarding the products' aromaticity, biochar contains more aromatic groups due to the higher production temperature, while hydrochar contains more alkyl moieties.Since pyrolysis occurs at higher temperatures, biochar also has a lower H/C ratio and the presence of graphite-like layers with particles of varying sizes.On the other hand, the surface of hydrochar samples consists of spherical particles with more uniform sizes [56].
Scanning electron micrographs (SEM) of biomass, biochar, and hydrochar derived from CV are shown in Figure 3a-c.The cells of CV in the biomass are mostly spherical (Figure 3c), but the biochar appears to be deformed due to cell fragmentation during thermal treatment.Wang et al. [57] reported that the particles of biochar derived from CV are compact and irregular.Reactions during pyrolysis can cause a fragmented, porous structure [58].The hydrochar obtained from spherical particles appears to be porous, but the spherical shape of the cells is still almost preserved.At a 200% magnification, the hydrochar's surface appears more porous and irregular.Scanning electron micrographs (SEM) of biomass, biochar, and hydrochar derived from CV are shown in Figure 3a-c.The cells of CV in the biomass are mostly spherical (Figure 3c), but the biochar appears to be deformed due to cell fragmentation during thermal treatment.Wang et al. [57] reported that the particles of biochar derived from CV are compact and irregular.Reactions during pyrolysis can cause a fragmented, porous structure [58].The hydrochar obtained from spherical particles appears to be porous, but the spherical shape of the cells is still almost preserved.At a 200% magnification, the hydrochar s surface appears more porous and irregular.

Results
The adsorption tests revealed interesting patterns for the studied variables; Figure 4 reports the results in terms of the percentage of Cd ions that were removed.
The initial pH of the metal-containing solution is usually a very relevant variable.Biochar, hydrochar, and biomass were assessed for the removal of Cd in batch experiments, where the initial pH ranged from 3 to 9. As shown in Figure 4a, the removal efficiency of Cd by biochar, hydrochar, and biomass was at its maximum at pH = 5.Increasing the pH value from 2 to 6 led to an increase in Cd removal, while increasing the pH value from 6 to 9 resulted in a decrease in Cd removal.When the solution s pH is above 8,

Adsorption Tests 3.2.1. Results
The adsorption tests revealed interesting patterns for the studied variables; Figure 4 reports the results in terms of the percentage of Cd ions that were removed.
The initial pH of the metal-containing solution is usually a very relevant variable.Biochar, hydrochar, and biomass were assessed for the removal of Cd in batch experiments, where the initial pH ranged from 3 to 9. As shown in Figure 4a, the removal efficiency of Cd by biochar, hydrochar, and biomass was at its maximum at pH = 5.Increasing the pH value from 2 to 6 led to an increase in Cd removal, while increasing the pH value from 6 to 9 resulted in a decrease in Cd removal.When the solution's pH is above 8, hydroxyl ions can react with Cd to produce a precipitate [59].At pH 9, only removal efficiencies of 45% for biomass, 56.9% for hydrochar, and 56% for biochar were achieved.The removal of Cd by chitosan-modified peanut shell biochar was also observed at pH levels ranging from 2 to 6, with removal efficiency decreasing as pH levels increased from 6 to 8.These results are consistent with those obtained when employing Ni/Fe bimetallic nanoparticles for the removal of Cr [60].Large amounts of H + in solution media can effectively compete with Cd cations for active adsorption sites.Additionally, most researchers have reported that the ideal pH range for heavy metal adsorption is from 5 to 6 [61].
hydroxyl ions can react with Cd to produce a precipitate [59].At pH 9, only removal efficiencies of 45% for biomass, 56.9% for hydrochar, and 56% for biochar were achieved.The removal of Cd by chitosan-modified peanut shell biochar was also observed at pH levels ranging from 2 to 6, with removal efficiency decreasing as pH levels increased from 6 to 8.These results are consistent with those obtained when employing Ni/Fe bimetallic nanoparticles for the removal of Cr [60].Large amounts of H + in solution media can effectively compete with Cd cations for active adsorption sites.Additionally, most researchers have reported that the ideal pH range for heavy metal adsorption is from 5 to 6 [61].The effect of adsorbent doses on Cd removal at optimal pH (6) was also studied (Figure 4b).There has been a clear increase in the removal rate of Cd by each adsorbent as the adsorbent dosage increased from 0.1 to 0.8 g L −1 ; however, after 0.8 g L −1 of each adsorbent, only a little increment was observed.Hence, the adsorbent dose of 0.8 g L −1 appears near optimal for each adsorbent.
The effect of contact time is shown in Figure 4c.The contact time ranged from 5 to 180 min.The percentage of Cd removal on biochar, hydrochar, and biomass increases with longer contact time.There is a significant increase in Cd removal within the first 30 min, followed by a gradual increase up to 180 min for biochar.However, for hydrochar and biomass, the adsorption remains relatively constant thereafter.For heavy metal adsorption/absorption, comparable trends have been reported previously.The initial increase in adsorption is attributed to the abundance of available adsorption sites that become saturated over time, resulting in decreased adsorption efficiency after 30 min [62].Therefore, an equilibrium time of 30 min was considered for adsorption in this study.
The effect of the initial Cd concentration is depicted in Figure 4d.Overall, biochar, hydrochar, and biomass exhibited a similar response pattern.The removal efficiency decreased as the initial Cd concentration increased.Higher initial metal concentrations  The effect of adsorbent doses on Cd removal at optimal pH (6) was also studied (Figure 4b).There has been a clear increase in the removal rate of Cd by each adsorbent as the adsorbent dosage increased from 0.1 to 0.8 g L −1 ; however, after 0.8 g L −1 of each adsorbent, only a little increment was observed.Hence, the adsorbent dose of 0.8 g L −1 appears near optimal for each adsorbent.
The effect of contact time is shown in Figure 4c.The contact time ranged from 5 to 180 min.The percentage of Cd removal on biochar, hydrochar, and biomass increases with longer contact time.There is a significant increase in Cd removal within the first 30 min, followed by a gradual increase up to 180 min for biochar.However, for hydrochar and biomass, the adsorption remains relatively constant thereafter.For heavy metal adsorption/absorption, comparable trends have been reported previously.The initial increase in adsorption is attributed to the abundance of available adsorption sites that become saturated over time, resulting in decreased adsorption efficiency after 30 min [62].Therefore, an equilibrium time of 30 min was considered for adsorption in this study.
The effect of the initial Cd concentration is depicted in Figure 4d.Overall, biochar, hydrochar, and biomass exhibited a similar response pattern.The removal efficiency decreased as the initial Cd concentration increased.Higher initial metal concentrations enhance the velocity at which mass transfers from liquid to solid surfaces, possibly increasing the adsorption capacity.However, the decrease in Cd removal efficiency at high concentrations can be attributed to the adsorbent being saturated.As the Cd concentration in the solution increases, more Cd is adsorbed onto the material.At low Cd concentrations, there is high accessibility to adsorption sites, and all Cd ions bind to the adsorbent.However, as metal ion concentration increases further, the rate of adsorption decreases due to saturation of available sites.
The obtained adsorption capacities can be compared with those of similar materials that are reported in the literature.To this aim, some values are reported in Table 4.The adsorption capacity is indeed comparable, although the CV materials are not the bestperforming ones.In this framework, the production cost will likely play a key role in determining the optimal material for the application.

Adsorption Isotherms Modeling
The Langmuir, Freundlich, and Temkin isotherms were used to describe the adsorption characteristics of Cd onto biochar, hydrochar, and raw biomass.The values of q max , K, and R 2 in the Langmuir isotherm model were assessed from the linear plot between C e /q e and C e , with their values reported in Table 5.Furthermore, the values of n, K f , and R 2 in the Freundlich isotherm model and b T , K T , and R 2 in the Temkin isotherm model were determined from the linear plots of logq e against logC e and q e against lnC e , respectively, as Figure 5 depicts.The Langmuir isotherm showed a better R 2 ranging from 0.98 to 0.99 compared to the Freundlich isotherm model (0.913-0.976) and Temkin models (0.96-0.98) in all samples.In addition, the Langmuir model appeared as the superior fit, implying that all samples were monolayered and had identical binding sites distributed equally all over their surface for Cd removal.
Table 5. Fitting parameters of various isotherm models based on Cd adsorption onto biochar, hydrochar, and biomass.

Langmuir
Freundlich Temkin The maximum Cd capture capacity (q max ) is well described by Langmuir fitting.In this study, the values for biochar, hydrochar, and biomass were 24.39 mg g −1 , 23.58 mg g −1 , and 16.56 mg g −1 , respectively.The adsorption isotherm is a tentative equation that depends on temperature, the surface area of the adsorbent, the concentration of solute in the solution, and the nature of the adsorbent.A higher A T value for biochar and hydrochar than that of biomass indicates that with pyrolysis and hydrothermal carbonization, a stronger adsorption potential can be achieved.The Temkin adsorption isotherm fits nicely with correlation coefficients ≥0.97 (as per Table 5), implying the chemisorption of Cd onto the adsorbent [68].It shall be emphasized again that the Cd removal mechanism may be more complex than plain adsorption, involving phenomena such as precipitation due to reactions with OH -ions and cation exchange with active sites on the material's matrix, just to cite some [69].More advanced analytical techniques and models [33] would be necessary for a more rigorous description of the Cd removal mechanism at a molecular level; these will be considered in future works.

Structural Equation Modeling (SEM)
The factor loadings obtained from the model implementation are presented in Table 6.In many cases, when calculating the correlation between indicators and their corresponding structure, an appropriate value equal to or greater than 0.4 is considered significant [70].Kline [71] further explains that factor loadings range between zero and one.Loadings below 0.3 are considered weak and are disregarded, while loadings between 0.3 and 0.6 are deemed acceptable.Loadings exceeding 0.6 are considered highly desirable.Following the assessment of the validity and reliability of the measurement model, the SEM is examined to determine the relationships between the independent variables.In this research, commonly used criteria are employed to evaluate the fit of the SEM, including significant coefficients (T-values), the determination coefficient (R ), and the predictive power coefficient (Q 2 ).
The fundamental criterion for measuring the relationships between constructs in the SEM is the significance of T-values.If the absolute value of these values is greater than or equal to 1.96, it indicates a statistically significant relationship between the constructs, confirming the research hypotheses at a 95% confidence level.Figure 6    R 2 is a measure utilized to establish a connection between the measurement and structural components of SEM, demonstrating the influence of an independent variable on a dependent variable.One of the principal advantages of the partial least squares (PLS) method is its capability to diminish errors in measurement models or amplify the C 2024, 10, 2 16 of 21 variance between constructs and indicators.An important aspect to note is that the R 2 value is exclusively computed for the dependent structures of the model; for independent structures, this criterion holds a value of zero.Ranging from zero to one, the R 2 value signifies the degree of fit the SEM across three levels: weak (0 to 0.19), moderate (0.19 to 0.33), and strong (0.33 to 0.67).Table 7 presents the R 2 results.Notably, the R 2 values for all parameters indicate a moderate to strong level of fit.This measure determines the predictive power of the model.According to the beliefs of researchers, models with an acceptable structural fit should be capable of predicting the indicators related to the endogenous structures of the model.This implies that if the relationships between the structures are accurately defined in a model, these structures will have a significant impact on each other's indicators, thus confirming the research hypotheses.In the case of an endogenous structure, the value of Q 2 can fall into three categories: 0.02 to 0.15 (weak predictive power), 0.15 to 0.35 (medium predictive power), and above 0.35 (strong predictive power).If the value of Q 2 for an endogenous construct is zero or negative, it indicates that the relationships between other constructs in the model and the endogenous construct are not well explained, suggesting the need for model modification.In general, this criterion demonstrates the predictive power of the model based on three levels: weak, medium, and strong.Table 8 presents the results of the Q 2 index.According to Table 8, it is evident that the model exhibits very strong predictive power since the predictive power of the structures exceeds 0.35. Figure 7 presents the results of the intensity of the effect of each variable and the mediating effect of time on Cd removal from water.Time is used as a mediator because all the investigated variables are influenced by time, and they exert their effects over a period.Both Figures 6 and 7 demonstrate that all parameters have a significant impact on Cd removal in water.Notably, the type of material, when mediated by time with an effect intensity of 0.77, exhibits the greatest influence on Cd removal compared to other variables.Additionally, the direct material type, with an effect intensity of 0.61, is crucial in removing Cd.The experiment's results also highlight the significant impact of time on Cd removal through both direct and mediated paths.Furthermore, concentration shows a significant effect on Cd removal through the mediating path of time.Overall, the intensity of the effects is higher in the intermediate paths compared to the direct path, emphasizing the significance of time in the Cd removal process.The intensity of the effect of materials such as biochar and hydrochar on Cd removal in aqueous environments can be quite significant.Both biochar and hydrochar are known for their strong adsorption capabilities, making them effective in removing heavy metals like Cd from water.Biochar and hydrochar have porous structures, providing ample sites for Cd ions to adsorb onto their surfaces.The adsorption process involves the attraction and binding of Cd to the functional groups present on the biochar and hydrochar surfaces.The effectiveness of these materials in Cd removal depends on various factors, such as the specific properties of the biochar and hydrochar, the dosage used, the initial concentration of Cd in the water, and pH of the aqueous solution.Moreover, the type of material and its preparation methods can also influence the adsorption capacity.Therefore, it is crucial to optimize the characteristics and application of biochar and hydrochar to achieve maximum Cd removal efficiency.
of the effects is higher in the intermediate paths compared to the direct path, emphasizing the significance of time in the Cd removal process.The intensity of the effect of materials such as biochar and hydrochar on Cd removal in aqueous environments can be quite significant.Both biochar and hydrochar are known for their strong adsorption capabilities, making them effective in removing heavy metals like Cd from water.Biochar and hydrochar have porous structures, providing ample sites for Cd ions to adsorb onto their surfaces.The adsorption process involves the attraction and binding of Cd to the functional groups present on the biochar and hydrochar surfaces.The effectiveness of these materials in Cd removal depends on various factors, such as the specific properties of the biochar and hydrochar, the dosage used, the initial concentration of Cd in the water, and the pH of the aqueous solution.Moreover, the type of material and its preparation methods can also influence the adsorption capacity.Therefore, it is crucial to optimize the characteristics and application of biochar and hydrochar to achieve maximum Cd removal efficiency.

Conclusions
CV holds great industrial potential due to its high production rate and availability.This study aimed to compare the physicochemical properties and Cd adsorption/absorption performance of biomass, biochar, and hydrochar derived from CV.The results showed that the conversion of CV biomass to biochar and hydrochar caused a decrease in volatile matter content and pH in hydrochar.SSA was only slightly increased after both pyrolytic and hydrothermal carbonization, which conversely more significantly affected pore volume and diameter.Treatment through pyrolysis and HTC led to an increase in C

Conclusions
CV holds great industrial potential due to its high production rate and availability.This study aimed to compare the physicochemical properties and Cd adsorption/absorption performance of biomass, biochar, and hydrochar derived from CV.The results showed that the conversion of CV biomass to biochar and hydrochar caused a decrease in volatile matter content and pH in hydrochar.SSA was only slightly increased after both pyrolytic and hydrothermal carbonization, which conversely more significantly affected pore volume and diameter.Treatment through pyrolysis and HTC led to an increase in C mass fraction while decreasing N, O, S, and H.The presence of functional groups (as evidenced by FTIR) and irregular pores suggests the applicability of all three materials for soil and water pollutant sorption.Scanning electron micrographs showed an increase in the number and pore size of the carbonized materials compared to the raw biomass.More advanced analytical techniques, such as thermogravimetric analysis and thermal desorption spectroscopy (to quantify the ion exchange sites), could also be interesting for future studies.
The maximum Cd capture capacity of biochar, biomass, and hydrochar was investigated: the adsorption performances of biochar and hydrochar resulted both similar to one another and better than that of the parent raw CV.The results showed that Cd removal depended on adsorbent dosage, contact time, and pH.The ideal conditions for the highest Cd removal were observed for all the materials tested at an adsorbent dosage of 0.8 g L −1 , an initial Cd concentration of 30 mg L −1 , and a pH of 6 within 30 min.The maximum adsorption capacities of biochar, hydrochar, and biomass were determined to be 24.39 mg g −1 , 23.58 mg g -1 , and 16.6 mg g −1 , respectively.The experimental data fit three well-known adsorption isotherm models well, seemingly implying that they may represent reasonable simplifications for the observed removal.Nonetheless, from the literature, it is well-known that the capture of Cd ions is much more complex and involves phenomena other than physical adsorption, such as the formation of ionic bonds with the cations.Nonetheless, such a deep examination of the full mechanism is beyond the scope of this work.More advanced experimental and modeling techniques are required to attain this aim, which be addressed in future works.
It is important to note that the efficiency of CV and its carbonized derivatives in removing Cd is influenced by various factors, such as initial Cd concentration, pH, time, and temperature.Using structural equation modeling to categorize the variables affecting the removal of Cd in water allows for the simultaneous examination of multiple variables and their interrelationships, providing a holistic view of how various factors interact and influence Cd removal, enabling a more comprehensive analysis than studying individual variables in isolation.Once the most appropriate material and operating conditions are established, further practical details will need to be investigated with care, such as the possibility of regenerating the sorbent and the effects of the presence of other metal ions.

Figure 4 .
Figure 4. Effect of (a) pH, (b) adsorbent dosage, (c) time, and (d) initial Cd concentration on the Cd removal.

Figure 4 .
Figure 4. Effect of (a) pH, (b) adsorbent dosage, (c) time, and (d) initial Cd concentration on the Cd removal.

21 Figure 6 .
Figure 6.T-values of different components effective on the removal of Cd.

Figure 6 .
Figure 6.T-values of different components effective on the removal of Cd.

Figure 7 .
Figure 7. Intensity of the effect of different variables on the removal of cadmium from water, with time as a mediating factor.

Figure 7 .
Figure 7. Intensity of the effect of different variables on the removal of cadmium from water, with time as a mediating factor.

Table 2 .
Results from the characterization of CV and its biochar and hydrochar.

Table 3 .
Tentative assignments of bands found in FTIR spectra of each material: biomass, biochar, and hydrochar.

Table 4 .
Maximum Cd adsorption capacities (mg g −1 ) of some carbonaceous materials from the literature.

Table 5 .
Fitting parameters of various isotherm models based on Cd adsorption drochar, and biomass.

Table 6 .
Coefficients of weight factor for the investigated parameters affecting Cd removal.

Table 7 .
R 2 coefficients of endogenous variables in the model.

Table 7 .
R 2 coefficients of endogenous variables in the model.

Table 8 .
Q 2 index coefficient of the fitted model.