Advancements in Biodegradable Active Films for Food Packaging: Effects of Nano/Microcapsule Incorporation

Food packaging plays a fundamental role in the modern food industry as a main process to preserve the quality of food products from manufacture to consumption. New food packaging technologies are being developed that are formulated with natural compounds by substituting synthetic/chemical antimicrobial and antioxidant agents to fulfill consumers’ expectations for healthy food. The strategy of incorporating natural antimicrobial compounds into food packaging structures is a recent and promising technology to reach this goal. Concepts such as “biodegradable packaging”, “active packaging”, and “bioactive packaging” currently guide the research and development of food packaging. However, the use of natural compounds faces some challenges, including weak stability and sensitivity to processing and storage conditions. The nano/microencapsulation of these bioactive compounds enhances their stability and controls their release. In addition, biodegradable packaging materials are gaining great attention in the face of ever-growing environmental concerns about plastic pollution. They are a sustainable, environmentally friendly, and cost-effective alternative to conventional plastic packaging materials. Ultimately, a combined formulation of nano/microencapsulated antimicrobial and antioxidant natural molecules, incorporated into a biodegradable food packaging system, offers many benefits by preventing food spoilage, extending the shelf life of food, reducing plastic and food waste, and preserving the freshness and quality of food. The main objective of this review is to illustrate the latest advances in the principal biodegradable materials used in the development of active antimicrobial and antioxidant packaging systems, as well as the most common nano/microencapsulated active natural agents incorporated into these food-packaging materials.


Introduction
The quality and safety of food products has always been a concern in the food industry. The large number of people affected by foodborne illnesses, about 600 million people in 2015 [1], and the increasing risk of the transmission of these diseases by the growth of international trade elucidates the necessity of improving food safety strategies. Microbial spoilage causes the loss of more than 25% of food products before consumption and wastes a considerable amount of food each year [2]. Using active packaging and antimicrobial additives for food preservation are two important target areas to protect and extend the shelf-life of perishable foods by preserving them from external environmental impacts and contamination [3]. Packaging can reduce or prevent foods from physical damage and spoilage and preserve beneficial constituents and organoleptic properties from the time of packaging to the time of consumption [4]. Different parameters are considered to control the food quality, including water activity, pH, temperature, light, and the partial The use of bio-based polymeric materials is part of the progress of food packaging that takes into account environmental concerns. The next step in improving food packaging is to prevent or retard the deterioration of packaged food. Based on the sources used, we can differentiate between first-, second-, and third-generation feedstocks based on the classification of biofuels. The first generation is based on edible materials such as maize, sugarcane, whey, or corn. The second generation includes lignocellulosic and non-edible residues such as municipal waste or side-stream products from food and agriculture industries. The third generation includes biomass from algae [25]. It has been proven that films derived from biopolymers have an excellent potential to contain various additives, such as antimicrobial and antioxidant agents, in their matrix and release them during storage [2,[26][27][28]. This packaging system is called "active packaging" and helps to extend the shelf life of food by absorbing (scavenging compounds) or diffusing (emitting compounds) various compounds. Scavengers have the ability to remove undesirable substances such as oxygen, moisture, ethylene, carbon dioxide, and odor from the internal packaging space. Emitters can release substances that have a positive impact, such as antimicrobial or antioxidant agents, enzymes, nutraceuticals, and aromatic compounds [2,29].
Active packaging can reduce the risk of foodborne pathogens and improve the quality and safety of food products [1,4]. They offer many advantages by reducing, restricting, or inhibiting the growth of spoilage and pathogenic microorganisms in food products and effectively extending the shelf life of packaged content. This strategy avoids adding the antimicrobials directly to the food product and offers the potential to control their release during storage time [27,28,30]. The use of bio-based polymeric materials is part of the progress of food packaging that takes into account environmental concerns. The next step in improving food packaging is to prevent or retard the deterioration of packaged food. Based on the sources used, we can differentiate between first-, second-, and third-generation feedstocks based on the classification of biofuels. The first generation is based on edible materials such as maize, sugarcane, whey, or corn. The second generation includes lignocellulosic and non-edible residues such as municipal waste or side-stream products from food and agriculture industries. The third generation includes biomass from algae [25]. It has been proven that films derived from biopolymers have an excellent potential to contain various additives, such as antimicrobial and antioxidant agents, in their matrix and release them during storage [2,[26][27][28]. This packaging system is called "active packaging" and helps to extend the shelf life of food by absorbing (scavenging compounds) or diffusing (emitting compounds) various compounds. Scavengers have the ability to remove undesirable substances such as oxygen, moisture, ethylene, carbon dioxide, and odor from the internal packaging space. Emitters can release substances that have a positive impact, such as antimicrobial or antioxidant agents, enzymes, nutraceuticals, and aromatic compounds [2,29].
Active packaging can reduce the risk of foodborne pathogens and improve the quality and safety of food products [1,4]. They offer many advantages by reducing, restricting, or inhibiting the growth of spoilage and pathogenic microorganisms in food products and effectively extending the shelf life of packaged content. This strategy avoids adding the antimicrobials directly to the food product and offers the potential to control their release during storage time [27,28,30].
Among the incorporated additives, much attention has been paid to natural antimicrobial agents. Among these, essential oils (EOs), which are aromatic substances that are considered as secondary metabolites and are extracted from different parts of plants and used for many years in traditional medicines, have attracted a great deal of attention in the food industry [31,32].
Despite the promising results of EOs as antimicrobial agents, their volatility, low solubility in water, and sensitivity to oxidation limit their applications in producing food packaging films [3,33]. A promising technology to eliminate these limitations is encapsulation. Encapsulation could be performed through different techniques in which EOs are considered a core material covered by wall materials. Various wall materials, such as carbohydrates, proteins, and lipids, were used to encapsulate active EOs molecules, which improves their solubility and stability and protects them during film making [31,34]. In this context, it is important to choose appropriate wall materials compatible with core properties and the conditions of encapsulation and film formation [35]. Microencapsulation is a process in which active molecules are loaded into micro-size-capsules (>1 µm) protect and isolate them from environmental conditions, masking undesirable flavors, and increasing their solubility and stability [36]. These microcapsules can be modified by reducing their size to obtain nano-size-capsules (less than 100 nm) in order to improve their properties, including bioavailability, solubility, and adsorption [34,37]. Generally, the main outcomes of nanoencapsulation are the reinforcement of biological activity and bioavailability due to the larger surface of interaction with food and, thus, the higher possibility of penetration into the cell membrane of microorganisms, which results in being more effective and supplying controlled release to the food. The strategy of incorporating nanoencapsulated bioactive molecules into film packaging extends the time of food storage by inhibiting the growth of pathogenic and spoilage microorganisms, along with using fewer amounts of antimicrobial agents and avoiding their direct addition to food products.
Considering the above discussion, this review aims to summarize the potential of bio-based polymers and the natural antimicrobial and antioxidant agents in the area of biodegradable active packaging. It also highlights the encapsulation strategies used to overcome the bioactive molecules limitations, and the most common nano/microencapsulated active natural agents incorporated into these food-packaging materials.

Biodegradable Food Packaging
More than 40% of the petroleum-based plastic materials produced are used for packaging, and half of those are used for food packaging. About 95% of plastic packaging is discarded after the first use [38]. The degradation of plastics can occur through chemical, physicochemical, or physical processes. It may take place following one or a combination of four mechanisms in nature, namely, photodegradation, hydrolysis, thermo-oxidative degradation, and biodegradation [39]. Photodegradation caused by UV-B radiation often initiates the degradation of common plastics. Degradation then moves forward through hydrolysis and thermo-oxidative degradation. Finally, degradation processes break down plastics into fragments with a lower molecular weight, which can be metabolized by microbes. The duration of degradation depends on the conditions and type of material, but the process is slow, and it may take more than 50 years for full degradation [39,40].
The definition of biodegradable bioplastic according to the European standard EN 13432 is "Under the action of microorganisms in the presence of oxygen, decomposition of an organic chemical compound into carbon dioxide, water and mineral salts, other elements present (mineralization) and appearance of a new biomass. In the absence of oxygen, decomposition into carbon dioxide, methane, mineral salts, and creation of a new biomass" [41]. Plastic biodegradation has been studied by focusing on the isolation of individual microorganisms that are able to decompose biodegradable plastics. It has been proved that bacterial and fungal consortia have a great potential in plastic waste biodegradation and bioremediation [17]. The polymeric chains are broken down into compounds such as oligomers, dimmers, and monomers with a lower molecular weight by enzymatic fractionation [42].
Plastic production has almost doubled during the last decade, and it is predicted that it will increase more, reaching 33 billion tons by 2050. The recent world health crisis caused by the spread of COVID-19 caused more plastic pollution due to the massive consumption of plastics for medical use and personal protective equipment, as well as using plastic shopping bags to prevent cross-contamination. For instance, medical waste has sharply increased by 370% and packaging plastic by 40% [43].
Consequently, plastic pollution has become one of the most critical environmental problems. Plastic has become ubiquitous, and it is a serious global problem for nature, human health, society, and the global economy [44][45][46]. Plastic pollution causes hazardous impacts on water systems, soil conditions, and air quality. The digestion and entanglement of plastic debris is an acute danger to animal and human life, and plastic waste destroys wildlife habitats [46]. Plastic consumption causes many troubles, including behavior disorders, dietary dilution, obesity, altering human chromosome sequences, infertility, and even cancer [17]. In addition, recent research investigated the effect of plastic consumption and proved the negative impacts on adolescent mental health and behavioral problems [47].
Thus, the growing accumulation of plastic wastes in nature increases the pressure to tackle the problem. Recycling aims to consume fewer raw materials, but it remains technologically and economically a big challenge [48]. Various degrees of recyclability of different products, consumer information about different recycling labels for plastic, appropriate technology, plastic waste management strategies, and risk of contamination make the recycling process complex. Indeed, the collecting, preprocessing, and recycling of plastic waste is complicated and expensive [38]. In fact, less than 10% of all plastic waste was recycled by the end of 2015 [12,49]. Incineration is also used to tackle plastic pollution, but it causes the release of undesirable gases such as dioxins, dioxin-like compounds, carbon monoxide, nitrogen oxides, alkenes, alkanes, aromatic, and chlorinated hydrocarbons into the atmosphere [50].
Therefore, biodegradability is a critical point that should be considered. Indeed, some petroleum-derived compounds, such as aliphatic-aromatic copolymers, have the potential to produce biodegradable polymers with good technical properties and modify their microstructure and composition to meet the particular requirements for different applications [51]. While biodegradability is a useful feature of these petroleum-based polymers, the processes of their production are polluting. Furthermore, fossil resources are limited, and they recharge only after millions of years. Thus, an alternative to fossil-based polymers is essential.
Thanks to extensive research, bioplastics have been introduced as a promising alternative that can be biodegradable and renewable. Figure 2 illustrates a general classification of biodegradable and non-biodegradable fossil and biobased plastics. Hence, there are the following four different groups of plastics:

•
Fossil-based and non-biodegradable: refers to classical plastics such as conventional polyethylene (PE) and polystyrene (PS); • Fossil-based and biodegradable: includes polycaprolactone (PCL), polybutylene succinate (PBS), and poly (butylene adipate-co-terephthalate) (PBAT); • Bio-based and non-biodegradable: bio-polyethylene (PE) is an example of this group produced from bioethanol fuel, which is produced from sugar cane; • Bio-based and biodegradable: this group is an interesting choice with high potential to apply in food packaging without environmental impacts, which can be natural or synthetic such as cellulose, starch blends, and polyesters such as PLA and PHA [52]. European Bioplastics introduced the term "bioplastics" in 2016 [52]. In order to better understand this concept and clear up any confusion, it is worth noting some definitions related to this notion. The term "biomaterials" is reserved for materials for medical use and is defined as "non-living material used and designed to interact with biological systems". Biopolymers are polymers made by living organisms (proteins, polysaccharides, etc.) or biodegradable synthetic polymers. Agro-polymers are also applied as polymers made by living organisms and derived from agricultural resources (starches, cellulose, etc.). Materials that are derived in whole or in part from biomass resources are called "biobased." Biomass resources are organic materials that are available on a renewable or recurring basis, such as crop residues, wood residues, grasses, and aquatic plants. Corn ethanol is a well-known example of a bio-based material derived from biomass resources. Bio-based refers technically to any product that contains some amount of bio-based material. The term is typically applied only to materials containing carbon. Bioplastics is a broader term, dedicated to biodegradable and/or bio-based polymers produced by synthesis [52].
The production of bioplastics has increased in recent years. About 2.1 million tons were produced in 2019, according to European Bioplastics, and this amount is predicted to rise to 2.4 million tons around 2024. Biodegradable and non-biodegradable parts account for 58.1% and 41.9% of total bioplastics, respectively ( Figure 3). Meanwhile, the total capacity of biodegradable polymers is still quite small compared to petroleum-based plastics. European Bioplastics introduced the term "bioplastics" in 2016 [52]. In order to better understand this concept and clear up any confusion, it is worth noting some definitions related to this notion. The term "biomaterials" is reserved for materials for medical use and is defined as "non-living material used and designed to interact with biological systems". Biopolymers are polymers made by living organisms (proteins, polysaccharides, etc.) or biodegradable synthetic polymers. Agro-polymers are also applied as polymers made by living organisms and derived from agricultural resources (starches, cellulose, etc.). Materials that are derived in whole or in part from biomass resources are called "bio-based." Biomass resources are organic materials that are available on a renewable or recurring basis, such as crop residues, wood residues, grasses, and aquatic plants. Corn ethanol is a well-known example of a bio-based material derived from biomass resources. Bio-based refers technically to any product that contains some amount of bio-based material. The term is typically applied only to materials containing carbon. Bioplastics is a broader term, dedicated to biodegradable and/or bio-based polymers produced by synthesis [52].
The production of bioplastics has increased in recent years. About 2.1 million tons were produced in 2019, according to European Bioplastics, and this amount is predicted to rise to 2.4 million tons around 2024. Biodegradable and non-biodegradable parts account for 58.1% and 41.9% of total bioplastics, respectively ( Figure 3). Meanwhile, the total capacity of biodegradable polymers is still quite small compared to petroleum-based plastics.  [53]. * PEF is currently in development and predicted to be available on a commercial scale in 2023.
Polybutylene adipate terephthalate (PBAT), polylactic acid (PLA), polyhydroxyl alkenoate (PHA), and polybutylene succinate (PBS) are principal synthetic bioplastics commercially used to date [52]. Research on bioplastics is in progress to improve their properties, such as film-forming and barrier properties, and broaden their applications. For example, polylactic acid (PLA) is an important example of this group. It is a very versatile polyester and the most prevalent polymer synthesized from biomass. PLA has, besides starch blends, the highest production capacity of the biodegradable materials available [54]. PLA is biodegradable and industrially compostable and is used in food packaging due to its non-toxicity. It is obtained from lactic acid during the fermentation of renewable crops such as sugar beets and corn [23]. PLA is sealable at lower temperatures and acts as both a flavor and an odor barrier for foodstuffs. Its industrial composting starts after only 8 days at temperatures between 50-60 °C and 60% relative humidity (RH). This time can be decreased if PLA is blended with PCL, a biodegradable petroleum-based polymer, and becomes home-compostable [55]. All polymer materials used for packaging can be theoretically substituted with those types synthesized from renewable monomers. However, there is an economic challenge regarding processing costs and also the lack of a collection channel for these bioplastics [56].
Some of the commercially produced biodegradable polymers are shown in Table 1.  Polybutylene adipate terephthalate (PBAT), polylactic acid (PLA), polyhydroxyl alkenoate (PHA), and polybutylene succinate (PBS) are principal synthetic bioplastics commercially used to date [52]. Research on bioplastics is in progress to improve their properties, such as film-forming and barrier properties, and broaden their applications. For example, polylactic acid (PLA) is an important example of this group. It is a very versatile polyester and the most prevalent polymer synthesized from biomass. PLA has, besides starch blends, the highest production capacity of the biodegradable materials available [54]. PLA is biodegradable and industrially compostable and is used in food packaging due to its non-toxicity. It is obtained from lactic acid during the fermentation of renewable crops such as sugar beets and corn [23]. PLA is sealable at lower temperatures and acts as both a flavor and an odor barrier for foodstuffs. Its industrial composting starts after only 8 days at temperatures between 50-60 • C and 60% relative humidity (RH). This time can be decreased if PLA is blended with PCL, a biodegradable petroleum-based polymer, and becomes home-compostable [55]. All polymer materials used for packaging can be theoretically substituted with those types synthesized from renewable monomers. However, there is an economic challenge regarding processing costs and also the lack of a collection channel for these bioplastics [56].
Some of the commercially produced biodegradable polymers are shown in Table 1.

Biopolymers
Biopolymers are interesting candidates for biodegradable packaging. They are extensively used on the market, especially in food packaging, because they are bio-based, nontoxic, and biodegradable. They are biodegradable materials with a faster generation rate. Biopolymers can be obtained from various resources, such as plants and domestic and marine animals. Based on their origin, they are classified into the following three main groups: polysaccharides, proteins, and lipid-based packaging [57].

Polysaccharide-Based Packaging
Polysaccharides are one of the most important bio-based polymers. Thanks to many favorable properties and being nontoxic, polysaccharides have been used in food packaging. Polysaccharides are the most abundant carbohydrates found in nature. They are longchain polymeric carbohydrates composed of monosaccharide units bound together by glycosidic linkages. They are made from nearly 40 different monosaccharides with various structures. There are different types of polysaccharides with distinct properties [58]. The following two classes of polysaccharides are available: (i) hetero-polysaccharides, which may contain two or more different monosaccharides such as gellan and xanthan, and (ii) homo-polysaccharides, which contain one type of mono-saccharide such as pullulan, curdlan, levan, and bacterial cellulose with linear chains [59]. Some polysaccharides, including starches, cellulose, alginates, carrageenan, and chitosan, are used for packaging because their properties are appropriate for manufacturing film packaging [4].
These resources include wood, agricultural residues, factory and food wastes, food leftovers, marine organisms, some types of grass, cereal brans and husks, sugarcane bagasse, corn kernels, along with microbial biosynthesis (algae, fungi, bacteria) and peels of different fruits and vegetables [86,87]. Some of its derivatives are cellulose acetate, sulfate, nitrate and carboxymethyl, ethyl and methyl nano-cellulose [88]. They have interesting characteristics such as being edible, biodegradable, lightweight, nontoxic, bioavailable, and having nutritional value and favorable sensory and organoleptic properties such as color, appearance, aroma, flavor, and taste, and they can be easily found in significant quantities at a low cost. They also have a high potential to be used for encapsulating and incorporating various active molecules of antimicrobial and antioxidant materials [89]. It is worth mentioning that cellulose of bacterial origin exhibits extraordinary and differentiated properties compared to other polysaccharide-based polymers. It is receiving extensive attention for applications in the food industry as a thickening and gelling agent, stabilizer, water-binding additive, and also as a food packaging material [90].
Cellulose has excellent physical and mechanical properties and high thermal resistance, but there are some shortcomings, including a high water absorption capacity and insufficient interfacial adhesion. Cellulose has been studied for many years to improve its properties. Cellulose multilayers were assessed to enhance barrier properties, resulting in further tensile strength, as well as grease resistance and barrier to water [91]. The effect of incorporation of carotenoids in cellulose acetate, as natural antioxidants, was studied and showed good protection for foods susceptible to photooxidation [92]. Thereby, due to its outstanding characteristics, cellulose used for food packaging reduces the cost of food packaging and preserves a wide range of foodstuffs in an eco-friendly manner.

Alginate
Alginate is the salt of alginic acid, a bio-based polymer consisting of D-mannuronic and L-guluronic monomers extracted from brown marine algae (brown seaweeds) and some bacteria, such as Pseudomonas aeruginosa [93,94]. Alginate is nontoxic, non-antigenic, biocompatible, and biodegradable, and it has the capacity to form a hydrogel when applied in encapsulation. Due to these properties, alginate is used in textiles, cosmetics, and pharmaceutics, and also in food industries as a thickener and stabilizer [95][96][97][98]. In the food industry, alginate is extensively used in the preparation of edible coatings because of its film-forming properties, hydrophilicity, and biocompatibility [99,100]. The application of alginate-based coatings in food preservation is limited due to their poor antimicrobial, UV-shielding, and water barrier properties. Some studies were dedicated to overcoming these shortcomings [101,102]. One recent study investigated the effect of the incorporation of phenolic compounds such as thymol into the sodium alginate film for fresh-cut apple slices. This film exhibited remarkable inhibition of the growth of Staphylococcus aureus and Escherichia coli, as well as a reduction in weight loss and retention of nutrients, and the surface color of apple slices. These thymol/sodium alginate films also showed a high tensile strength and elongation at break, as well as UV-vis light-blocking capability [103].

Carrageenan
Carrageenan is a polysaccharide extracted from marine red algae by hot alkali separation. Akin to other polysaccharides, carrageenan is nontoxic, biocompatible, and biodegradable with a low immunogenicity. Furthermore, carrageenan offers excellent properties compared with other encapsulation materials, such as a better stability of capsules, higher electronegativity, and a better protection of encapsulated contents, allowing them to be considered a good candidate in delivery systems for bioactive ingredients [104,105]. Therefore, it has an extensive range of applications in the food and pharmaceutical fields. Various structures of carrageenan make different biological activities, including antioxidant, antitumor, immunomodulatory, anti-inflammatory, anticoagulant, antiviral, antibacterial, antifungal, and anti-hyperglycemic properties.
Carrageenan has many applications in the food industry, including gelling, thickening, stabilizing, protective coating, and fat substitution [106]. Many authors developed pH-sensitive and antioxidant-packaging films based on carrageenan [107]. Another investigation showed a protective effect of fish oil, encapsulated in carrageenan, against lipid and protein oxidation and an improvement in the shelf life and sensory characteristics of enriched nuggets [108].

Chitosan
Chitosan, a linear polysaccharide with (1-4)-linked 2-amino-deoxy-β-d-glucan derived from chitin, is the second most abundant biopolymer and the most abundant biopolymer of animal origin. It is found in the exoskeletons of crustaceans and insects and in the cell walls of fungi and yeast [109]. It is a multipurpose biopolymer with interesting physicochemical and biological properties that are applied in agriculture, pharmacy, and biomedicine industries [110]. It is used in food packaging due to its low cost, biodegradability, biocompatibility, non-toxicity, film formation, viscosity, and ion binding [111]. The combination of chitosan with other biomaterials, nanometals, and active compounds allows further exploitation of chitosan and modification of some of the shortages of its characteristics, including hydrophilicity, weak mechanical properties, low gas permeability, and low encapsulation efficiency, as well as enhancing the bioavailability and biological properties [112].
The emerging chitosan-gelatin composite films present excellent physical properties, including mechanical, surface hydrophobicity, color, barrier, and thermal characteristics [113]. Further, chitosan films incorporated with ε-polylysine were used for packaging beef fillet. Different features were investigated, and this technique was introduced as an effective way to extend the shelf life of beef fillets and maintain their quality during refrigerated storage [114]. Another study highlighted the antioxidant and antimicrobial activities of chitosan-based packaging incorporated with nanocapsules of Cinnamodendron dinisii essential oil with zein as the wall material. This active chitosan-based film was tested on beef and showed preservative effects against spoilage and color changes [115].

Protein-Based Packaging
One of the other important types of bio-based polymers are proteins with two main plant and animal origins. They are made of different polar and nonpolar α-amino acids. There are different sources of plant-origin proteins such as wheat gluten, corn zein, soy, peanut, rice-bran, cotton seed, barley, and sunflower, along with animal origins such as gelatin, collagen, casein, whey, and fish myofibrillar protein [116]. The proteins of plant origin are used more due to their greater availability and lower cost.
Proteins are extensively used as packaging materials due to their good mechanical characteristics, abundance, and high nutritional value. They also have the potential to be incorporating agents for active packaging applications in addition to their nontoxicity and biodegradability [116,117]. However, some shortcomings, such as a high level of sensitivity to moisture and poor water vapor barrier properties, need to be improved. In fact, films that are composed of plant protein isolates have excellent oxygen barrier properties due to their polar nature and crosslinked polymer network; however, the water vapor barrier is low [25]. Using plasticizers, cross-linkers, and other additives through various physical, chemical, and enzymatic methods can be applied for this purpose [4,118]. The most used protein-based polymers are presented below.

Soy Protein
Soy proteins are composed of globulin proteins 7S (β-conglycinin) and 11S (glycinin), which have different structures, functional, and molecular properties. The functional properties of soy products depend on these two components [119].
Soy proteins have many applications, such as adhesives, composites, plastics, and so on, in different industries, including the food industry. Soy proteins are biodegradable and have exceptional film-forming properties. Furthermore, the effectiveness of incorporating antimicrobial compounds into soy protein films has been reported; therefore, soy protein can be used for producing film packaging [120][121][122]. Nevertheless, there are some limitations, such as low mechanical and thermal properties, poor processability, and water sensitivity, which can effectively be modified through laminating, coating with other polymers, plasticizing, nanoparticle reinforcing, or blending methods [123]. As an example, Ref. [124] investigated the mechanical and barrier properties of soy protein isolatebased films coated with polylactic acid and demonstrated improvements in the mechanical and water barrier properties of the film. Furthermore, using cellulose nanocrystals in soy protein films showed better film-forming, tensile strength, barrier properties, and water resistance. This film was evaluated for packaging pork and strawberries and showed fewer total viable counts and total volatile basic nitrogen of stored pork meat and extended the shelf-life of strawberries [125]. A new strategy of incorporating polyethyleneimine as a plasticizer and lignin-silver nanoparticles as a green reinforcer into soy protein films has made it possible to manufacture tough, strong, and UV-shielding soy protein-based composite films [126].

Wheat Gluten
Wheat gluten is a by-product of the wheat starch industry. It comprises mainly two water-insoluble proteins called glutenin and gliadin. Gliadins are composed of lowmolecular-weight proteins ranging from 30,000 to 80,000 Da and glutenin containing high-molecular-weight proteins ranging from 80,000 to several million Da. The functional and structural characteristics of these two proteins determine the functional properties of wheat gluten. Generally, the films produced from glutenin showed better barrier properties than the films from gliadins or whole gluten [91,127,128]. Owing to its viscoelastic properties, lower solubility, and biodegradability, wheat gluten has many food and nonfood applications. Wheat gluten films are used in food packaging because of their oxygen barrier properties. However, they present a poor water vapor barrier that can be modified by adding plasticizers, coatings, and blends with hydrophobic polymers [129]. In this regard, Ref. [130] reported that wheat gluten/silica hybrid coating films could improve the inherent moisture sensitivity of this protein with a four-fold reduction in water vapor transmission rate. In addition, the films prepared from the blending of three thermoplastic gluten and polycaprolactone (PCL), with and without chrome octanoate as a food-grade catalyst, were recommended as potential shape-memory food packaging materials [131].
Wheat gluten films also have the potential for combination with antimicrobial materials to protect contents from spoilage [132]. The use of carvacrol as an antimicrobial agent and montmorillonite as a filler in wheat gluten-coated papers improved the antimicrobial efficiency against Escherichia coli [133].

Corn Zein
Zein is a class of prolamin protein found in the endosperm of corn (maize) mainly composed of α-zein, β-zein, and γ-zein [134]. It is extracted from corn gluten meal, a byproduct of starch production, through ethanolic extraction. Zein can form tough, glossy, hydrophobic, greaseproof coatings, and it is considered an antimicrobial agent. Zein is an abundant, renewable material with a low cost. Thus, it has a variety of applications in the food, chemical, environmental, medical, metallurgical, pharmaceutical, and biotechnology industries [135,136].
Zein is a hydrophobic and thermoplastic material, soluble in alcohol but insoluble in water that has film-forming properties and has been used commercially as an edible film for nuts and confectionery products for many years [4,137]. Zein films are manufactured via different processes, including the casting of solutions of zein, thermoplastic processing, and blown extrusion. The mechanical and thermal characteristics of zein are affected by the processes by which they are produced [137,138]. They offer high tensile strength and low water vapor permeability, and the water resistance of zein films can be improved by lamination with fatty acids because of their ability to form hydrophobic interactions with fatty acids [139]. Some mechanical properties of zein films need to be improved, such as fragility and flexibility, by adding plasticizers or blending with other biopolymers to remove these drawbacks [140][141][142]. A recent study assessed the mechanical properties of gelatin/zein composite films and introduced them as good candidates for high moisture food packaging applications due to the great improvement in water insolubility, water vapor permeability, and mechanical properties compared with conventional gelatin and zein films [143].

Casein and Whey Proteins
Milk proteins are composed of the following two dominant proteins: casein in the form of micelles, which accounts for approximately 80% of the total proteins, and the remaining 20% are whey proteins. Casein, the main protein of milk, has four types, namely, αs1-, αs2-, β-, and κ-casein [144]. Casein micelles are composed of large numbers of casein molecules, which are stabilized by calcium-phosphate bridging [145]. It can be used in food packaging because it can produce a flexible and transparent film with good gas and lipid barrier properties at low relative humidity. It also shows good emulsifying behaviors along with the mechanical and thermal stability of the caseinate.
Whey protein is a by-product of the cheese-making process or a by-product of acid casein production. Roughly 70% consists of a mixture of β-lactoglobulin (β-Lg) and αlactalbumin (α-La). The other components of whey protein are protease peptones, bovine serum albumin, immunoglobulins, and other minor proteins [146].
Globally, milk proteins have high nutritional value, which provides much of the protein and amino acid dietary needs for the human diet. They are natural animal products with excellent functional and sensory properties and are safe for food applications [147]. Their functional and structural characteristics make them versatile materials as a sustainable source of biopolymers. Their most important properties are their nutritional value, biodegradability, biocompatibility, safety, thermal stability, emulsification, gelation, foaming, and water-binding capacities [148]. Thanks to these features, they are used in packaging and also in active packaging with incorporated bioactive and nutraceutical compounds [13,149]. The film-forming capacity and biodegradability of milk proteins make them a promising alternative to conventional non-biodegradable packaging [150]. Composite films containing milk protein-based biopolymers degrade in a very short time, with 100% degradation on day one without harmful residues. However, there are economic feasibility challenges to be overcome in the coming years [151].
Despite the potential of using milk proteins as a biopolymer for packaging, they exhibit some disadvantages compared to other conventional polymer materials, including their poor mechanical and barrier properties against gases, aromas, and water vapor. These drawbacks can be overcome in several ways, including blending with other edible biopolymers to form composite materials [152], multilayering films by coatings with nanoor micro-dimensions of more than one type of biopolymer, and also adding synthetic plasticizers [144,153]. An improvement in the bactericidal properties of the casein and chitosan blend in film packaging due to the presence of ionic interaction between both macromolecules was proven by [154].
It is worth noting that milk proteins constitute a range of biological activity components. For example, casein is an important source of antimicrobial peptides [155,156]. Furthermore, milk proteins can be used as macro and nano carriers for the encapsulation of nutraceuticals, vitamins, minerals, and antimicrobial compounds due to their biocompatibility, ease of controlling the release, and dispersibility of the encapsulated compounds [157]. Using antimicrobial agents in casein and whey protein film packaging has been investigated in many studies. The inhibitory effect on Staphylococcus aureus of casein-based films containing Zataria multiflora as the essential oil has been proved [158]. Further, the antimicrobial potential of cheese whey bioactive proteins and peptides such as lactoferrin in the development of antimicrobial edible film composites was reported by [159].

Gelatin
Gelatin is produced from the partial hydrolysis of collagen. In the past, gelatin has been manufactured from bovine and porcine skin and bone. In recent years, fish and poultry have also been used to produce gelatin. Production of fish gelatin is increasing due to vegetarianism and the potential of halal and kosher markets [160]. Gelatin has gel-forming properties that offer many applications in food, photography, cosmetics, and pharmaceutics. More notably, it is widely used in food to provide elasticity, viscosity, and stability. Further, it has a linear structure and limited monomer composition, leading to excellent film-forming properties [161]. Gelatin is used as an emulsifier, foaming agent, colloid stabilizer, biodegradable film-forming material, micro-encapsulating agent, and source of bioactive peptides when enzymatically hydrolyzed [162].
Gelatin films possess good mechanical, functional, and barrier properties, depending on the film's formulations and processing conditions. However, they are sensitive to moisture and show poor barrier properties against water vapor, which can be improved by using plasticizers or cross-linking agents or combining with other biopolymers such as soy protein isolate, oils, fatty acids, and certain polysaccharides [163][164][165][166].
Adding antimicrobial and antioxidant compounds into gelatin films also conferred more preservation of foodstuffs. Recently, the effect of curcuma in gelatin film was investigated by [167] and revealed remarkable antimicrobial activity against foodborne pathogenic bacteria, E. coli, and L. monocytogenes, and showed strong antioxidant activity along with improvement of the UV protection, water vapor barrier, and mechanical properties. In addition, the antimicrobial and antioxidant properties of the gelatin films were increased by embedding different kinds of functional nanoparticles such as quercetin, lactoferrin, and chitosan nanofiber into a gelatin-based film [168].
In conclusion, all these protein-based biopolymers are being studied massively due to their promising functions for the production of biodegradable active packaging with many beneficial economic and environmental attributes, enhancing the safety and quality of food products.

Lipids-Based Packaging
Lipids are classified into different types, such as phospholipids, phosphatides, mono-, di-, and tri-glycerides, terpenes, cerebrosides, fatty alcohol, and fatty acids. They are extracted from various natural resources of animal, insect, and plant origins. Among them, glycerides or waxes are mainly used in the production of films. These compounds are mainly nonpolar with a high hydrophobicity, insoluble in aqueous media, and soluble in organic solvents. They are used for coatings and edible films based on different biodegradable materials, including polysaccharides and proteins, due to their excellent moisture barrier properties [13,169]. They have a glossy appearance, minimize moisture loss, and reduce the cost of packaging films [170]. Lipids are also used as carriers for various bioactive compound-delivery in the food and pharmaceutical industries [171,172].
Packaging films using lipids have been studied for many years, and it is moving forward because of the capacity of lipids-based polymer to produce effective active edible films. Palm wax was incorporated into fish gelatin film used in food packaging, resulting in better UV barrier, mechanical, and water resistance properties [173]. Lipids can also be combined with other biopolymers in order to modify their poor hydrophobic characteristics. Recently, carnauba wax was added into a starch-based film to enhance its hydrophobicity and reduce its water solubility and improve its thermal stability and moisture, light and water vapor barrier properties [174].

Microorganism-Based Packaging
Microorganisms are another source to produce biopolymers. Many microorganisms are used to produce polymer materials, including Alcaligenes, Bacillus, Azotobacter, Rhizobium, and Halobacterium [57,175]. For instance, some polymers are produced from microorganisms such as polyhydroxyalkanoates (PHA), poly(β-hydroxybutyrate) (PHB), poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV), levan, curdlan, gellan, dextran, bacterial cellulose, and microbial polysaccharides including exopolysaccharides, capsular polysaccharides, and xanthan. They are applied in the medical, agricultural, and packaging fields. Among them, PHAs and bacterial cellulose are the most produced polymers [22,55]. PHA polymers are resistant to heat and ultraviolet light. PHAs are durable for high-speed processing and can withstand high temperatures during storage [25]. Genetically modified microorganisms were also introduced to produce biodegradable polymers with renewable sources. However, genetic engineering is controversial, and it is believed that it is harmful to human health.

Active Biodegradable Packaging Films
Packaging is a barrier from gases, moisture, dust, or light, but conventional packaging is not totally effective for preventing the spoilage of food products [28] by chemical or biological reactions. Chemical spoilage mostly happens by oxidation processes of food ingredients, and biological spoilage is caused by enzymes, viral and parasitic activity, and microbial contamination [176]. Among them, microbial contamination is one of the main reasons for food deterioration. Many preservation techniques have been applied for a long time, such as fermentation, drying, thermal processing, freezing, refrigeration, modified atmosphere, irradiation, and, more notably, adding antimicrobial agents to the food [177].
In this regard, antimicrobial agents can be mixed with food to inhibit microbial growth. In such cases, a considerable quantity of antimicrobial compounds would be required, which may have an undesirable impact on the quality, taste, organoleptic properties, and appearance of foods. Moreover, as many of these materials have low stability, there is the possibility of neutralization of antimicrobial agents quickly at the same time by the active substances in food or during processing. Antimicrobial agents can also be added directly to the surface of food, and their effectiveness can be limited by diffusing them into the mass of food, which can cause the same unfavorable results as their combination with food [176].
Therefore, in order to overcome these problems and extend the preservation period of foods along with maintaining their quality, their sensory property, and freshness, some modern strategies are needed. Intelligent packaging and active packaging are two promising technologies that promote the shelf life of food products with minimal adverse effects. In intelligent packaging, various sensors and indicators are employed, including time-temperature indicators, gas indicators, humidity sensors, optical, calorimetric, and electrochemical biosensors for detecting defects, quality monitoring, and following the packaged contents to control the storage conditions during all steps of food processing to the consumption step [29].
Active packaging applies absorption and diffusion mechanisms to protect the foodstuffs and extend their shelf life. Active packaging can act as a scavenger and absorb various materials such as carbon dioxide, oxygen, and ethanol, which cause the spoilage of foods. Active packaging can contain various active molecules such as antimicrobials, antioxidants, and even coloring and nutritional agents, which can be emitted from the packaging into the foods during the storage time [178].
Active and intelligent packaging are already used for food packaging in the USA, Japan, Australia, and other countries. California-based Nature Fresh Farms is a company that uses active packaging for vegetables such as brussels sprouts and cucumbers, with plans to widen active packaging use for their products. Some other companies, including Uvesa, ElPozo Alimentación, BTSA. Biotecnologías Aplicadas, Monteloeder, Nurel, Bandesur Alcalá, and SP group, collaborated in an active packaging project to extend the shelf-life of meat with active packaging (Avanza-S project). Moreover, an edible coating developed by Eden Agritech, a startup company in Thailand, extended the shelf-life of fresh-cut fruit by up to three times [179].
However, strict European regulations for food contact materials and the safety aspects of the application of these innovative technologies have restricted their applications. Knowledge about consumer acceptance, economic aspects, and environmental impacts is required for more developments and applications [180]. Indeed, the development and application of active and intelligent packaging systems needs both legislative regulation and consumer acceptance. In this regard, a European study was conducted within the EU FAIR R&D program framework, called the Actipak project (January 1999-December 2001). It contributed to establishing and implementing active and intelligent packaging in the current relevant regulations for packaged food in Europe and initiated amendments to European legislation for food-contact materials. The aim of this project was the classification of active packaging, including antimicrobial release films, and the evaluation of antimicrobial films on cheese, meat, and fruit [180]. At that time, there was no European regulation that specifically covered the use of active and intelligent packaging. Later, in 2009, the issuing of European Regulation (EC) No. 450/2009 helped faster market penetration in Europe [181].

Antimicrobial Active Packaging
Antimicrobial packaging can be made from different polymers, including petrochemicalbased polymers and bio-based materials. Meanwhile, a wide range of antimicrobial agents, chemical or natural, can also be applied to manufacture antimicrobial packaging films. The necessity of producing healthy, high-quality foods and minimizing the side effects of chemical agents, along with less environmental impacts, causes researchers to use natural antimicrobial agents and biodegradable materials to make antimicrobial biodegradable packaging films [176].
Antimicrobial agents incorporated into biopolymeric compounds are released slowly into the food surface over time. In this way, an active concentration of antimicrobial agents is present on food for a longer time without the risk of neutralization and negative effects on food. This method extends the lag phases for the growth of microorganisms and prevents food spoilage. Keeping the balance between the release rate of antimicrobial agents and the food spoilage kinetics is a key point in optimizing the effectiveness of active packaging [179].
It is not possible to find a single antimicrobial agent that can suppress all types of microorganisms and prevent all kinds of food spoilage. However, many different biopolymers have potential applications in active packaging. Table 2 summarizes the recent studies related to food preservation by using antimicrobial bio-based films. There are several antimicrobial compounds authorized based on the standards of each country.

Natural Antimicrobial Agents of Plant Origin
Antimicrobial agents can be found in nature, especially in plants. A wide range of antimicrobial compounds are synthetized naturally in plants to protect against microorganisms and other predators.
There is a preference to use these agents in food because of the easy regulation process to extract them and consumer demand to reduce the use of synthetic food additives due to their undesirable effects. The most important natural antimicrobial agents are extracted from spices and herbs such as rosemary, cloves, horseradish, mustard, cinnamon, sage, oregano, basil, marjoram, savory, thyme, and many others. They are mainly in the form of essential oils (EOs) [182]. High antibacterial activity against Listeria monocytogenes and Staphylococcus aureus at 4 • C and 25 • C for 10 days, without any effect on the sensory quality of cheese. [184] Soft (minas frescal) cheese Nisin Starch/halloysite/nanocomposite films Listeria monocytogenes After 4 days, antimicrobial nanocomposite films with 2 g/100 g nisin significantly reduced the initial counts of the bacterium and those with 6 g/100 g nisin completely inhibited L. monocytogenes.

[185]
Cheddar cheese Nisin-silica liposomes Chitosan Listeria monocytogenes Anti-Listeria activity without effect on the sensory properties of cheese. [186] Fresh cheese and apple juice Nisin pullulan nanofibers

Chicken meat Tea tree oil (TTO)liposome Chitosan Salmonella enteritidis and Salmonella typhimurium
Almost no impact on the sensory properties. In total, 5 log 10 reductions of Salmonella were observed in chicken meat by TTO liposomes/chitosan nanofibers treatment for 4 days at 12 • C and 25 • C. [188]

Fish
Bacteriocin 7293 (Bac7293), a novel bacteriocin from Weissella hellenica BCC 7293 Poly (lactic acid)/sawdust particle biocomposite film  Better protection against UV light and reduced water solubility and water vapor permeability, and improvement of mechanical properties. Inhibition of microbial growth and minimization of oxidative rancidity in 12 days shelf life compared with 3 days shelf life for neat film. [191]

Lactic acid bacteria (LAB) and Total Mesophilic Aerobic (TMAB)
On the 4th day, the count of TMAB in the samples coated with NCL mats was 3.28 log CFU g −1 compared to 6.61 log CFU g −1 in control samples. [192]

Chicken breast fillets
Virgin olive oilgrape seed oiland savory essential oil Gelatin-pectin

Staphylococcus aureus, Salmonella typhimurium Fluorescence pseudomonas
Savory essential oil presented more antimicrobial activity. The mixture of them in film showed antimicrobial activity against mentioned bacteria for 12 days storage. [193]

Chicken breast fillets
Carvacrol (0.75% w/w) and citral (1.0% w/w) Sago starch and guar gum Bacillus cereus Escherichia coli The tensile strength of films reduced while elongation at break increased, and the film showed good antimicrobial activity. [194] Laurus nobilis essential oil and Rosmarinus officinalis essential oil Polyvinyl alcohol (PVOH) Listeria monocytogenes Inhibition of the lipid oxidation together with antimicrobial activity. [195] Lamb meat 2% rosemary oil Cellulose nanofiber/whey protein matrix containing titanium dioxide particles (1% TiO 2 )

Escherichia coli Salmonella enteritidis Listeria. monocytogenes Staphylococcus aureus
The active packaging significantly reduced microbial growth, lipid oxidation, and lipolysis of the lamb meat during storage. [196]  The active film showed a high thermal stability with decreasing water vapor permeability. Strawberries had lower weight loss after 15 days of storage, better freshness preservation without fungal attack, and antimicrobial activity against bacteria. [197]

Cherry tomatoes Cinnamon
Chitosan as the outer layer and the mixture of sodium alginate and the amphiphilic starch as the intermediate layer

Escherichia coli Staphylococcus aureus,
This active film showed more freshness and lower weight loss rate within two weeks compared to polyethylene films. The inhibition growth rates for E. coli and S. aureus were 36% and 30%, respectively, and soil biodegradability rate was 70% in 28 days. [198] Cucumber

Clove oil Chitosan Escherichia coli
Maintained the color and flavor of cucumber for more than 4 days and until 4.97 log 10, reductions of E. coli biofilm in population. [199] Strawberries Thyme Porous polylactic acid (PLA) nanofibers and coated with poly(vinyl alcohol)/poly(ethylene glycol) (PVA/PEG) blends

Escherichia Coli Staphylococcus aureus
Strawberries packed with this film exhibited better freshness and more than 99% antimicrobial activity against mentioned bacteria. [200]

Escherichia coli Staphylococcus aureus Aspergillus niger
The broad-spectrum, direct, and indirect (gas phase) antimicrobial activity was observed against bacteria and fungi. [201]

Vegetable products Cinnamon and oregano Cellulose Listeria grayi Listeria monocytogenes
Cinnamon and oregano essential oils inhibited the growth of both bacteria in the vapor phase. The packaging with cellulose stickers impregnated with cinnamon reduced the Listeria count on frozen vegetable samples. [202]

Cinnamon Zein
Escherichia coli Improvement of barriers and mechanical properties of zein film with antimicrobial effect on E. coli and fruit samples.

Bacillus cereus Escherichia coli
The tensile strength of films reduced while elongation at break increased, and the film showed good antimicrobial activity. [194] Foods Essential oils (EOs) are the second metabolite and naturally volatile organic compounds produced from the extraction of different parts of plants, including flowers (jasmine, rose, violet, and lavender), herbs, buds (clove), leaves (thyme, eucalyptus, salvia), fruits (anis, star anise), twigs, bark (cinnamon), zest (citrus), seeds (cardamom), wood (sandal), rhizomes, and roots (ginger) [210]. They are present in cavities, secretory cells, epidermic cells, canals, or glandular trichomes. Essential oils present antibacterial, antifungal, anti-inflammatory, anesthetic, insecticidal, and antiviral properties. Thereby, they have many applications in the cosmetic, perfumery, pharmaceutic, beverage, feed, and food industries [211,212]. They are produced by various methods, such as solvent extraction, supercritical fluid extraction, hydro distillation, solvent-free (microwave) extraction, physical expression (cold pressing), ultrasound-assisted extraction, and combinations of extraction methods [182,210,213]. Essential oils are composed of a mixture of about 20-80 individual components at different concentrations, most of which are terpenes, terpenoids, aldehydes, isoflavonoid acids, and ketones. The antimicrobial activity of EOs depends on the chemical structure of these individual components. There are about 3000 essential oils; approximately 300 are used for food, cosmetics, fragrance, and medical applications. EOs are naturally hydrophobic and lipophilic compounds, with a density that is often lower than water. They are soluble in organic solvents such as ether, alcohol, and fixed oils but immiscible with water. They can be isolated from the aqueous phase via decantation [33,210].
Essential oils have gained a growing interest in the food industry and packaging due to their antimicrobial and antioxidant properties applied to the preservation of foodstuffs, including fruits, vegetables, fish, meat, and dairy products [3]. As they are natural compounds, they can be an excellent alternative to synthetic food additives. Their hydrophobicity allows them to permeate through the lipids of the cell membrane of bacteria, disrupting the structure and finally inhibiting them [33].
The antimicrobial effect of EOs has been studied in detail, and it depends on their chemical structure. It is confirmed that the presence of hydroxyl groups in phenolic compounds such as carvacrol and thymol has a key role in their activities against bacteria [214]. However, EOs are unstable, volatile compounds, which prevents their direct use on foods, as that would be ineffective with uncontrolled release. In fact, they start to degrade easily through oxidation, volatilization, heating, and light if they are not preserved from external factors [33,215]. Furthermore, EOs are aromatics that can have undesirable sensory effects. Encapsulation of essential oils into carriers such as liposomes, polymeric particles, and solid lipid nanoparticles is indispensable [3,216].
Many studies have been conducted on the antimicrobial activities of EOs on different microorganisms with promising results in inhibiting the growth of different types of pathogens, which has attracted huge attention in food packaging [217]. In this regard, a recent study conducted by [202] evaluated the antimicrobial activities of cinnamon, oregano, and carvacrol against L. grayi and L. monocytogenes in vitro. The results showed their effectiveness in inhibiting the growth of L. grayi as well as L. monocytogenes in the vapor phase. Chitosan films prepared by incorporation of apricot kernel essential oil, which is a strong antioxidant and antimicrobial agent, in different concentrations, showed excellent antimicrobial and antioxidant properties as compared to neat chitosan films. They successfully inhibited fungal growth on packaged bread slices, improved water resistance, and enhanced the water vapor barrier property [218].

Natural Antimicrobial Agents of Animal Origin
Some animal proteins and enzymes can act on both Gram-positive and Gram-negative bacteria by destroying their cell membranes [219]. Antimicrobial peptides are a large group of antimicrobial agents of animal origin, including pleurocidin, lactoferrin, defensins, and protamine [220]. Some enzymes such as lactoperoxidase and lysozyme, plus some polysaccharides and lipids from animal sources such as chitosan, as well as some fatty acids of animal origin such as eicosatetraenoic acid and docosahexaenoic acid, could also effectively act against Gram-positive and Gram-negative bacteria and fight foodborne microorganisms [219]. Chitosan, as the main part of these groups, was introduced in the previous section. Herein, we introduce some of the other most applicable antimicrobial substances of animal origin.

Pleurocidin
Pleurocidin is a novel antimicrobial peptide found in the skin mucous secretions of the winter flounder (Pseudopleuronectes americanus). It inhibits the growth of both Gram-positive and Gram-negative foodborne microorganisms. Its effect on some microorganisms, including Saccharomyces cerevisiae, E. coli O157:H7, L. monocytogenes, Vibrio parahemolyticus, and Penicillium expansum, was confirmed [221] for food preservation purposes. Incorporation of pleurocidin in poly-vinyl alcohol in order to preserve its bioactivity leads to the inhibition of foodborne pathogens, and it shows better efficiency compared to free pleurocidin samples tested with real foods such as apple cider [222].

Lactoferrin
Lactoferrin is an 80 kDa glycoprotein containing around 700 amino acids. It is a significant part of the non-heme iron-binding glycoprotein of our organism and belongs to the transferrin class. It is present in most mammalian body fluids such as milk [223]. Anti-inflammatory, antibacterial, antiviral, antioxidant, antitumor, anti-obesity, antibiotic, and immunomodulatory activities are some properties that have been reported to date. Lactoferrin regulates the free iron level in body fluids and causes bacteriostatic properties, which are beneficial for health [224,225].
It exhibits broad-spectrum antimicrobial properties against bacteria, viruses, and fungi [226]. Its bio preservative potential against Salmonella enterica and Escherichia coli O157:H7 as two common dairy pathogens was examined, and it showed a considerable reduction in their growth with only lactoferrin concentrations at or above 112.5 mg/mL in the milk [227]. Lactoferrin's antimicrobial activity makes it a potential candidate for use in food preservation. Recently, immobilization of lactoferrin in gelatin films improved their optical, mechanical, barrier, and preservative properties [168].

Lactoperoxidase
Lactoperoxidase is a heme-containing glycoprotein composed of 608 amino acids with a molecular mass of approximately 78 kDa [228]. It is an antimicrobial enzyme that is secreted in the epithelial cells of the mammary gland and is found in large amounts in cow's milk [229]. It can destroy bacteria such as Salmonella, Shigella, Pseudomonas, and coliforms. Thereby, it has applications in the food industry for the preservation of unprocessed milk, poultry, fish, and meat [230][231][232][233]. Due to its antimicrobial activity, lactoperoxidase has potential use in food packaging. Its incorporation into defatted soybean meal, a by-product left after crushing soybeans for oil, showed its effectiveness in sliced ham preservation without changing its sensory properties considerably [232].

Lysozyme
Lysozyme is another important enzyme widespread throughout the animal and plant kingdoms that shows protective biological functions [234]. Lysozyme is a basic protein in many living organisms, found in body fluids and tissues; therefore, there are many sources of lysozyme [235]. One of the most convenient sources is chicken eggs, the richest in lysozyme. It has interesting characteristics, including antimicrobial activity along with protection against infection, with the effect of strengthening the immune system [236,237]. Despite its interesting properties, the use of free lysozyme in packaging is restricted because it is unstable. Food protease can hydrolyze it and inactivate its catalytic activity [238,239]. The modification of lysozyme via heat, chemicals, and hydrolysis enhances its biological activities and broadens its applications [240]. According to [241], lysozyme coating in packaging films can reduce the water vapor permeability, oxygen permeability, and oil permeability without unwanted effects on the appearance of the films. The effect of lysozyme-N-succinyl chitosan on extending the shelf life of strawberries was proved [242]. Other authors assessed exploiting lysozyme nanofibers as antimicrobial and antioxidantreinforcing additives by incorporating lysozyme nanofibers into the pullulan matrix as an eco-friendly edible film [243]. Recently, [244] incorporated lysozyme into cold plasmaactivated polylactic acid pouches and assessed its effectiveness with pear juice and rice milk-based smoothies. The authors highlighted that activated packages could inhibit Listeria monocytogenes. The color of pouches manufactured with this method was also better and more stable [244]. Other studies demonstrated that the synergy of low-dose lysozyme enhanced the inhibition of eugenol-casein nanoparticles against Staphylococcus aureus and Bacillus sp. by 5.83-fold and 5.53-fold, respectively [245].

Antimicrobial Agent Produced by Microorganisms
Some microorganisms and their derivatives are able to inhibit the growth of other microorganisms [246]. Bacteriocins, produced by some bacteria such as lactic acid bacteria (LAB), are peptides with antimicrobial activity against various non-pathogenic and sometimes pathogenic bacteria [247]. They have recently received much attention due to their antimicrobial activity, especially bacteriocins generated from lactic acid in food and drug systems, most of which are classified as safe agents by the American Food and Drug Administration (FDA) [248].
Current bacteriocins that have the potential for food biopreservation are nisin, leucocin, lactocin 705, enterocin 4, and enterocin produced by various microorganisms [247]. Bacteriocins can be incorporated into packaging films to inhibit spoilage microorganisms and extend the shelf life of foods [247]. The incorporation of bacteriocin from lactic acid bacteria into active food packaging was successful in meat and meat products [249]. The active film obtained from polyvinyl alcohol blended with casein hydrolysates and nisin exhibited antimicrobial activity by reducing the growth of spoilage bacteria and then extending the shelf-life of the packaged food product [250]. The concentrated bacteriocin from lactic acid bacteria was also effective in reducing the growth of Listeria monocytogenes in ready-to-eat sliced emulsion-type sausage [251].
Pediocins are bacteriocins produced by Pediococcus spp., a group of homofermentative Gram-positive bacteria belonging to the Lactobacillaceae family [252]. It is an active peptide that specifically inhibits the growth of Listeria monocytogenes [253]. The activity of pediocin can be limited by the presence of salt, heat, or proteolytic enzymes, along with pH and storage time [254]. Pediocin has many applications in the food industry, including the preservation of fermented sausages, vegetables, and dairy products [255]. It can be used directly on food products as a preservative or incorporated into food packaging in order to prevent the spoilage of food products [256]. According to [257], adding nisin and pediocin to starch film inhibited the growth of L. monocytogenes and C. perfringens.
Reuterin is also an antimicrobial compound produced by Lactobacillus spp. strains in the presence of glycerol and is considered an antimicrobial agent against several pathogenic and spoilage microorganisms. Its effectiveness was evaluated for many foodstuffs, including meat, dairy products, beef sausages, and cooked pork, resulting in inhibition of L. monocytogenes, S. aureus, E. coli O157:H7, and so forth. Despite pediocin, reuterins act in a wide range of pH, which makes them a good candidate for biopreservation of many foods. It exhibits broad inhibitory activities against Gram-positive and Gram-negative bacteria, bacterial spores, molds, yeasts, and protozoa [258]. According to [258], reuterin at a concentration of 6.9 mM showed a fungicidal effect in yogurt.

Natural Antimicrobial of Algal and Mushrooms Origin
Mushrooms, with about 140,000 species, have antimicrobial and antioxidant capacities. In addition to their nutritional value, they have preservative and medical properties [259]. Methanol, ethanol, acetone, dichloromethane, and chloroform extracts of many different mushrooms showed inhibitory activity towards pathogenic microorganisms such as E. coli, S. aureus, B. subtilis, C. albicans, and P. aeruginosa and so forth [246,260]. Antimicrobial and anti-fungal effects of two wild edible mushrooms from the Kashmir valley, Morchella esculenta and Verpa bohemica, against E. coli and Aspergillus fumigates were assessed by [261]. Besides, the antimicrobial activity of Auricularia auricular-judae mushroom has been confirmed against Staphylococcus aureus, Bacillus subtilis, Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae, yeast (Candida albicans), and dermatophytic pathogens [262].
Algae also have antimicrobial activity due to their polyphenolic content [263]. Antimicrobial activity of various algae-derived compounds was reported, such as the effectiveness of Himanthalia elongata, Saccharina latissima, Laminaria digitate, Padina, and Dictyota against L. monocytogenes, Salmonella, Enterococcus faecalis, P. aeruginosa, B. cereus, and E. coli [246]. Attempts to exploit the antimicrobial and antioxidant properties of algae-derived compounds led to their being determined as good candidates for pharmaceutical applications as well as food coatings and films [246]. Polyelectrolyte structured films prepared from cationic starch and sodium alginate showed good thermal, antimicrobial, and surface properties [264].

Antioxidant Active Packaging
Higher than normal concentrations of free radicals during oxidative stress are very harmful to the body as they damage or modify the major components of a cell and cause many diseases. Oxidation is also one of the major causes of food spoilage. Antioxidants are radical scavengers that trap free radicals and help delay or prevent oxidation [265]. Indeed, antioxidants minimize oxygen in the food system by reducing the capacity of active antioxidants. Therefore, they retard both lipid oxidation and protein denaturation. They can also interrupt the oxidation chain reaction and prevent the oxidation reaction along with inactivation of enzyme activity, resulting in blocking catalyzed oxidation reactions [266].
Polyphenols, flavonoids, vitamins C, E, and terpenoids have been reported as natural and synthetic antioxidant agents [267]. Natural antioxidants, compared to synthetic antioxidants, exhibit benefits such as stronger antioxidant effects, better consumer acceptability, potential health benefits, and safety [268].
Two synthetic antioxidants, butylated hydroxyanisole (BHA) and butylated hydroxytoluene (BHT), have been extensively studied in active packaging. However, health awareness and the ever-increasing demand for using natural molecules are encouraging industries to use natural ingredients [269].
Recently, some strategies for incorporating active components such as oxygen scavengers and antioxidants into food packaging have been introduced for food preservation [179]. However, antioxidants may reduce or lose their activities due to interaction with the other ingredients or during processing [26]. The incorporation of antioxidants in the packaging matrix can help to overcome these defects, retard food spoilage, and extend the shelf life of packaged foods [179,275]. Antioxidants applied to food packaging should meet some criteria, such as being low cost, being non-toxic, having high activity at low concentrations, having strong permeability, and showing good stability without affecting the quality of the food [266]. In addition, the proper antioxidants for packaging applications should be chosen based on molecular size, polarity, and release properties of antioxidant compounds [276]. Some forms of antioxidant packaging are already used in the food industry, such as sachets, pads, or labels for foods in which iron and ferrous oxide are common active ingredients [277].
In the past few years, there have been extensive studies on active packaging with antioxidant compounds. A recent study assessed the antioxidant activity of green tea extract for meat preservation. It indicated the potential use of green tea extract in active films [278]. Additionally, polyfunctional starch/tea polyphenol nanofibrous films also demonstrated higher antioxidant activity and optimum mechanical and hydrophobic properties [279]. Moreover, Ref. [280] evaluated the antioxidant activity of chitosan films enriched with Artemisia campestris extracts. Artemisia campestris is a widespread species of plant in the sunflower family that exhibits antioxidant and UV-Vis barrier properties with good thermal stability. Ref. [281] investigated the influence of Syzygium cumini seed extract (SCSE) incorporation in sodium alginate/gum Arabic (SG) films. They highlighted that the addition of SCSE into SG films declined the thermal stability, elongation at break, tensile strength, and moisture content and improved the scavenging activity, opacity, solubility, and water vapor permeability. Ref. [282] produced sodium alginate (SA) maltodextrins (MD) based functional films incorporated with phenolic extract of Azolla pinnata leaves fern (AF). They demonstrated that the addition of AF extract to SA.MD films increased the thickness and enhanced the scavenging properties. Furthermore, the film's solubility, swelling degree, and water vapor permeability were decreased. Ref. [283] fabricated carboxymethyl cellulose (CMC) based novel functional films containing Chinese chives root extract (CRE) and revealed that a higher extract concentration decreased the tensile strength, water solubility, swelling degree, and water vapor permeability. Furthermore, the addition of CRE into CMC exhibited good antioxidant and antimicrobial activity of films.
Antioxidant packaging as an emerging active packaging has great potential for use in food packaging and preserving food in a safe and eco-friendly manner. This technology can consist of biopolymers or nanofillers to improve mechanical or physical properties, resulting in various antioxidant-active packaging for different foodstuffs.

Active Food Packaging with Nano/Microencapsulated Ingredients
The limitations of using most of these natural antioxidant and antimicrobial agents are their easy degradation, low water solubility, low bioavailability, and undesirable tastes [284]. Encapsulation is a promising technology for overcoming these limitations and enhancing the physical, chemical, and thermal stability along with masking the unwanted taste, increasing the bioavailability and solubility of natural antimicrobial and antioxidant compounds, and providing the possibility of controlled release and targeted delivery [284,285]. Indeed, this innovative technology keeps the sensitive bioactive natural compounds from damage under harsh conditions such as high temperature or pressure, light, oxidation, and neutralization because of unwanted interaction with the other ingredients or foods throughout processing and during storage periods. Thanks to encapsulation techniques, natural antimicrobial and antioxidant compounds are covered by wall material in order to protect their activities against external impacts [286,287].
Encapsulation of antimicrobial agents is highly useful for food applications, notably for active packaging with high breadth potential due to the vast variety of natural antimicrobial compounds and many possible wall materials for encapsulating them. It is a wide search field that has received huge attention recently, specifically the characterization of natural antimicrobial compounds and the choice of compatible shell materials.
Encapsulation is a process by which one substance in solid, liquid, or gaseous states is entrapped/coated in another material, called wall material. This process can produce different scales of particles, namely, millimeters, micrometers (microencapsulation), and nanometers (nanoencapsulation) [288]. The aim of encapsulation is to produce capsules in nano or micro size. Nano/microcapsules are composed of a core, which is surrounded by a monolithic shell (Figure 4). The core, which is mainly a bioactive agent, is centered in capsules, and it is also called the internal phase, encapsulant, payload phase, or fill. The shell that coats the core is considered a wall, coating, envelope, membrane, carrier, encapsulating agent, external phase, or matrix [289,290]. The micro/nanocapsules can be classified into four categories depending on whether they have a single-or multi-core and a shell. They can be found in the form of single-core with single-wall, or single-core coated by multi-wall, as well as multi-core with single-wall, or multi-core enveloped by multi-wall [291]. The main outcome of encapsulation is to overcome the physical instability and protect active molecules from degradation in addition to controlling the release of active molecules [292]. Indeed, encapsulation contributes to preserving the active molecule against harsh conditions such as high temperature, pressure, or pH through processing. Moreover, the possibility of controlled release is another important benefit of encapsulation. In this regard, encapsulation could minimize the concentration of active agents needed in different applications by controlling their release and preserving them against harsh conditions. More specially, the use of encapsulation techniques in the food industry confers several advantages, as mentioned by [291]. Their main advantages are as follows:


The preservation of sensitive molecules during processing conditions such as phenolic compounds with antimicrobial and antioxidant activity;  Encapsulation at nano and micro sizes enhances the bioavailability of active molecules;  The prevention of the alteration of the sensory properties of food by some bioactive agents with unpleasant aroma and taste. Essential oils and oil fish are two examples of active molecules with extreme aromas that can alter the taste of food. Encapsulation prevents the change in taste by covering the molecules and reducing the necessary concentration;  Controlled release of active compounds to improve food quality and safety;  The final product of the encapsulation process is mostly a fine powder. It offers several benefits, such as improvement of stability and flowability. It is easier to handle and store the active molecules. In addition, agglomeration and change in density can be reduced by encapsulation.
Different wall materials could be used for the encapsulation, depending on the nature of active molecules. The wall materials should meet some characteristics comprising resistance to high shears and mechanical stresses as well as the ability to incorporate the active molecules with the minimum thickness [293]. In addition, the wall material structures play a key role in encapsulation efficiency and the durability of micro/nanocapsules [294], and their compatibility with the core material is an important element for choosing a wall material. Stronger wall material or a double layer should be chosen for the encap- The core, which is mainly a bioactive agent, is centered in capsules, and it is also called the internal phase, encapsulant, payload phase, or fill. The shell that coats the core is considered a wall, coating, envelope, membrane, carrier, encapsulating agent, external phase, or matrix [289,290]. The micro/nanocapsules can be classified into four categories depending on whether they have a single-or multi-core and a shell. They can be found in the form of single-core with single-wall, or single-core coated by multi-wall, as well as multi-core with single-wall, or multi-core enveloped by multi-wall [291]. The main outcome of encapsulation is to overcome the physical instability and protect active molecules from degradation in addition to controlling the release of active molecules [292]. Indeed, encapsulation contributes to preserving the active molecule against harsh conditions such as high temperature, pressure, or pH through processing. Moreover, the possibility of controlled release is another important benefit of encapsulation. In this regard, encapsulation could minimize the concentration of active agents needed in different applications by controlling their release and preserving them against harsh conditions. More specially, the use of encapsulation techniques in the food industry confers several advantages, as mentioned by [291]. Their main advantages are as follows:

•
The preservation of sensitive molecules during processing conditions such as phenolic compounds with antimicrobial and antioxidant activity; • Encapsulation at nano and micro sizes enhances the bioavailability of active molecules; • The prevention of the alteration of the sensory properties of food by some bioactive agents with unpleasant aroma and taste. Essential oils and oil fish are two examples of active molecules with extreme aromas that can alter the taste of food. Encapsulation prevents the change in taste by covering the molecules and reducing the necessary concentration; • Controlled release of active compounds to improve food quality and safety; • The final product of the encapsulation process is mostly a fine powder. It offers several benefits, such as improvement of stability and flowability. It is easier to handle and store the active molecules. In addition, agglomeration and change in density can be reduced by encapsulation.
Different wall materials could be used for the encapsulation, depending on the nature of active molecules. The wall materials should meet some characteristics comprising resistance to high shears and mechanical stresses as well as the ability to incorporate the active molecules with the minimum thickness [293]. In addition, the wall material structures play a key role in encapsulation efficiency and the durability of micro/nanocapsules [294], and their compatibility with the core material is an important element for choosing a wall material. Stronger wall material or a double layer should be chosen for the encapsulation of highly sensitive molecules or under harsh conditions [34]. The apt shell in encapsulation exhibits some criteria, including the stabilization of the core, film-forming ability, flexibility, stability, low density, non-hygroscopicity, the capacity for controlled release, and no unwanted reactions with the payload [285]. Considering all these characteristics, various biopolymers have been applied in the encapsulation of food ingredients [291], including polysaccharides (gum arabic, modified starches, maltodextrins, alginates, pectin, carrageenan, cellulose derivatives, chitosan, and cyclodextrins), fats and waxes (hydrogenated vegetable oils, beeswax, lecithin, medium-chain triglycerides, and glyceryl behenate), proteins (gelatin, whey protein, sodium caseinate, soy protein, gluten, caseins, zein, and silk fibroin), and synthetic compounds (paclitaxel, mPEG500-b-p, polyacrylonitrile, polycaprolactone, polylactic acid, poly methyl methacrylate (PMMA), acrolein, and glycidyl methacrylate epoxy polymers). The natural materials are mostly cheap, abundant, non-toxic, and compatible with food formulations. There are some parameters that should be taken into account for designing the encapsulation process, including capsule size, final physical state, stability, and physical condition of the release [291,295].
The encapsulated particles are divided into three main classes that differ in size, namely, macrocapsules (with a size of more than 5000 µm), microcapsules (0.2-5000 µm), and nanocapsules (with a size of less than 0.2 µm). According to EU regulation, nanoparticles are attributed to the particles when at least 50% of the particles have a size of ≤100 nm [296], whereas pharmaceutical science considers nano size for particles with a size of less than 1000 nm.
Herein, the various techniques of microencapsulation along with nanoencapsulation are mentioned briefly. Microencapsulation techniques include spray drying as a more common technique, spray chilling, spray cooling, extrusion, fluidized bed coating, centrifugal extrusion, freeze-drying, coacervation, interfacial polymerization, molecular inclusion, and so forth [291,295].
Nanoencapsulation is more recent than microencapsulation. The different nanoencapsulation systems for loading natural antimicrobials are summarized in Figure 5, including nanoemulsions, nanoliposomes, solid lipid nanoparticles (SLNs), nanostructured lipid carriers (NLCs), biopolymeric nanoparticles, and equipment-based nanoencapsulation methods, which have commonly been applied to design the best delivery systems for antimicrobial substances [297]. The selection of the proper technology for each process depends on the physicochemical features, particle size, release type, delivery method, and economic and environmental aspects [291].
In nanoencapsulation, the size of particles is decreased to a nanometer by two basic methods, including top-down (using high-energy devices such as high-pressure-homogenizer, ultrasound, and milling) and bottom-up methods (using low-energy techniques such as spontaneous emulsification or anti-solvent precipitation) [298]. Nanocapsules with a nano-size have a higher ratio of surface to volume. Therefore, they offer higher solubility, bioavailability, and adsorption [34]. Nanoencapsulation exhibits several benefits such as homogeneity, improvement in physical and chemical properties, and shelf stability, in addition to better encapsulation efficiency and boosting the functional properties of active molecules [299]. Besides, the nanocapsules are more controllable. Furthermore, the release of micro-sized particles occurs more slowly, and over longer periods of time compared to nanocapsules. Consequently, a smaller number of nanoparticles is required. Furthermore, according to numerous studies, the emergence of nanotechnology in food packaging, in particular the use of nanocapsules in active packaging, offers interesting benefits such as more efficacy by inhibiting the growth of microorganisms, better thermal protection of bioactive compounds, and better release control [300]. In nanoencapsulation, the size of particles is decreased to a nanometer by two basic methods, including top-down (using high-energy devices such as high-pressure-homogenizer, ultrasound, and milling) and bottom-up methods (using low-energy techniques such as spontaneous emulsification or anti-solvent precipitation) [298]. Nanocapsules with a nano-size have a higher ratio of surface to volume. Therefore, they offer higher solubility, bioavailability, and adsorption [34]. Nanoencapsulation exhibits several benefits such as homogeneity, improvement in physical and chemical properties, and shelf stability, in addition to better encapsulation efficiency and boosting the functional properties of active molecules [299]. Besides, the nanocapsules are more controllable. Furthermore, the release of micro-sized particles occurs more slowly, and over longer periods of time compared to nanocapsules. Consequently, a smaller number of nanoparticles is required. Furthermore, according to numerous studies, the emergence of nanotechnology in food packaging, in particular the use of nanocapsules in active packaging, offers interesting benefits such as more efficacy by inhibiting the growth of microorganisms, better thermal protection of bioactive compounds, and better release control [300].
Nanoencapsulation is progressing at a rapid pace in the food sector. The nanoencapsulation of food ingredients aims to produce value-added food products with the possibility of applying this technology in active packaging to boost the preservation of foodstuffs. The incorporation of encapsulated bioactive compounds in the matrix of film packaging is a promising strategy for food preservation, particularly extending the shelf life of fresh foods. Capsules produced through a stable encapsulation process gain remarkable characteristics such as more physiochemical stability and better bioavailability, which show more interest as a delivery system [301,302].
Controlled release packaging (CRP) is a relatively new term that first appeared in the literature in 2005 [303]. A controlled release of bioactive molecules from a film into food is performed during storage periods. The migration of capsules containing antimicrobial or antioxidant compounds can be achieved by direct contact between food and active film Nanoencapsulation is progressing at a rapid pace in the food sector. The nanoencapsulation of food ingredients aims to produce value-added food products with the possibility of applying this technology in active packaging to boost the preservation of foodstuffs. The incorporation of encapsulated bioactive compounds in the matrix of film packaging is a promising strategy for food preservation, particularly extending the shelf life of fresh foods. Capsules produced through a stable encapsulation process gain remarkable characteristics such as more physiochemical stability and better bioavailability, which show more interest as a delivery system [301,302].
Controlled release packaging (CRP) is a relatively new term that first appeared in the literature in 2005 [303]. A controlled release of bioactive molecules from a film into food is performed during storage periods. The migration of capsules containing antimicrobial or antioxidant compounds can be achieved by direct contact between food and active film packaging or by gas phase diffusion from the packaging layer onto the food surface [304]. The uniqueness of CRP is that it focuses on the kinetics and mechanism of controlled release, what to release, when and how to trigger the release, how much to release, and how fast to release [305]. CRP using antimicrobials may be used for short-or intermediateterm microbial inhibition of highly perishable foods such as fresh meats, seafood, fruit, and vegetables. CRP using antioxidants may be used for long-term retardation of lipid oxidation for shelf-stable foods such as ready-to-eat meals containing fatty components susceptible to oxidation [306].
The control of the release rates of antimicrobial and antimicrobial agents is an emerging area of active food packaging. In fact, rapid release causes consumption of the antimicrobial within a short time, after which the minimum concentration required for the microbial growth inhibition is not maintained. On the other hand, spoilage reactions on the surface may start if the release of the antimicrobial agent from the packaging film is too slow [307]. Different materials and methods may be used in order to apply this strategy by means of various biopolymers and bioactive agents. To date, this technology introduces active antimicrobial packaging with a high potential to minimize the risk of food spoilage and contamination by suppressing the activities of targeted microorganisms. For example, encapsulated essential oils with antimicrobial properties are one of the interesting candidates to be applied for active food packaging. According to [308], lemon myrtle essential oil, encapsulated into cellulose acetate nanofibers, inhibited the growth of 100% Escherichia coli and Staphylococcus aureus even at the lowest loading concentration of lemon myrtle essential oil of 2 wt%. The antimicrobial activity of cinnamon oil was investigated against foodborne bacteria in free and encapsulated forms, and both exhibit antimicrobial activity. However, the encapsulated form showed antimicrobial action with a lower concentration of 57-125 ppm, compared with non-encapsulated cinnamon, with a concentration of 125-500 ppm. Controlled release of cinnamon capsules leads to better efficiency because the cinnamon concentration in the culture medium reaches its maximum after 4-6 h of incubation when the cells are in the exponential growth phase.
Luteolin, a flavone with potent antioxidant and antimicrobial activities, was encapsulated in oil-in-water nanoemulsions and incorporated into chitosan-matrix [309]. The authors compared films with encapsulated luteolin (CS-LLNEs), films without luteolin (CS-LL), and free luteolin films (CS) as controls. CS-LLNEs film showed slower controlled release to exert antioxidant activity for up to 10 days. In addition, CS-LLNEs film showed better water vapor and oxygen barriers and mechanical properties in comparison with CS-LL film.
Active packaging based on hydroxypropyl methylcellulose containing carvacrol nanoemulsions was developed to extend the shelf-life of wheat bread. The designed system has satisfactory antioxidant activity and good antibacterial activity against S. aureus and E. coli [310]. Grape seed extract-carvacrol microcapsules were incorporated into chitosan to extend the shelf-life of refrigerated salmon packages. The microcapsules improved the antimicrobial activity of the chitosan film and increased the shelf-life of refrigerated salmon to 4-7 days [311]. The multilayered pectin edible coating was designed with encapsulated trans-cinnamaldehyde to extend the shelf life of fresh-cut cantaloupe. Coated fruits lasted longer (7-9 days) compared to uncoated controls (4 days) at 4 • C [312].
Eventually, biodegradable film packaging containing capsules has great potential to meet the needs of three main goals of developed packaging science, comprising sustainability, safety, and convenience [31,313]. Recent progress in the incorporation of nano/microencapsulated natural agents into active food packaging systems is summarized in Table 3. Table 3. Incorporation of nano/microencapsulated natural agents in active food packaging systems.

Packaging Material and Encapsulated Antimicrobial System Purpose References
Active packaging based on hydroxypropyl methylcellulose containing carvacrol nanoemulsions Development of active packaging system to extend the shelf life of wheat bread.
The designed system has a satisfactory antioxidant activity, good antibacterial activity against S. aureus and E. coli. [310] Edible coating fabricated with chitosan, pectin, and encapsulated trans-cinnamaldehyde Designing a multilayered edible coating with antimicrobial agents to extend the shelf life of fresh-cut cantaloupe stored at 4 • C [312] Alginate coating containing nano-emulsified basil oil Development of a coating system against the following spoilage fungi: Penicillium chrysogenum and Aspergillus flavus [314] Active packaging based on hydroxypropyl methylcellulose containing oregano essential oil nanoemulsions Higher antimicrobial activity against all tested bacterial strains, particularly S. typhimurium [315] Starch-carboxy methyl cellulose films containing rosemary essential oil (REO)-loaded benzoic acid-chitosan (BA-CS) nanogel Using of encapsulated REO into BA-CS nanogel in film structure to obtain immediately (REO) and gradual (nanogel) antimicrobial effect against S. aureus [316] Polylactide films containing essential oils/nanoparticles Inhibiting the growth of L. monocytogenes and S. typhimurium on contaminated cheese [10] Active packaging containing cinnamon-loaded nanophytosomes into electrospun nanofiber Higher antimicrobial activity and improving the shelf life of shrimp [317] Active packaging based on cellulose nanocrystals (CNCs) reinforced chitosan, containing thyme-oregano, thyme-tea tree, and thyme-peppermint nanoemulsions Development of active antifungal packaging for rice preservation. Chitosan-based nanocomposite films loaded essential oils mixtures showed significant antifungal activity against Aspergillus niger, Aspergillus flavus, Aspergillus parasiticus, and Penicillium chrysogenum, reducing their growth by 51-77%. [318] Encapsulation of gallic acid into lentil flour-based nanofibers by electrospinning technology and use of these nanofibers as active packaging materials Enhancement of the oxidative stability of walnuts present in active packages with encapsulated gallic. The reduction in oxidation of walnuts with lower peroxide, p-anisidine, and TOTOX values was observed. [319] Active packaging film based on chitosan with grape seed extract-carvacrol microcapsules Development of active film to extend the shelf-life of refrigerated salmon. The microcapsules improved the antimicrobial activity of the chitosan film and increased the shelf-life of refrigerated salmon to 4-7 days. [311] Foods 2022, 11, 760 31 of 44

Conclusions and Future Developments
In recent years, sustainable packaging has been adopted by the food industry, either as a repackaging of environmental policies, as a marketing strategy in response to social pressures, or as a genuine attempt to grapple with the commercial, social, and environmental issues associated with plastic packaging. This review paper summarizes the current state of biodegradable and active packaging biopolymers as well as major antioxidant and antimicrobial natural agents incorporated into the polymers as nano-microcapsules. More than 300 sources were reviewed, including scientific literature and commercial information.
In conclusion, this review shows that biodegradable active biopolymers are generally characterized by low water vapor barrier properties; hence, the modification of their structure or other techniques can be convenient for modulating this property. These efforts can lead to the production of biodegradable active biopolymers with good barrier and mechanical properties. At the same time, more efforts should be implemented to decrease their price and their competition with food by increasing the use of second-and third-generation feedstock. Another challenge is the lack of a collection channel for these bioplastics. Further studies are necessary to establish biodegradable monolayer or multilayer materials as a viable alternative to commonly used fossil fuel-based materials for food products. A techno-economic analysis (TEA) combined with a life cycle assessment (LCA) should be implemented to estimate and quantify costs, emissions, and energy intensity associated with material acquisition, processing, transport, and end-of-life treatment of biodegradable packaging production.
At the same time, nano-microencapsulation of natural antimicrobial and antioxidant agents improves their physical, chemical, and thermal stability along with increasing their bioavailability and solubility, which provides the possibility of their controlled release and targeted delivery. However, this review highlighted that strict European regulations for food contact materials and safety aspects restricted the application of many encapsulated antimicrobial and antioxidant agents in the releasing systems. Eliminating legislative restrictions and creating a unique global organization would allow for more specific and exact legislation for food-contact materials. Meanwhile, the use of nanotechnology in the antimicrobial and antioxidant food packaging films requires the control and monitoring of nanomaterials as well as risk assessment, which requires information about their toxicity and exposure [296]. In line with this, the European Food Safety Authority (EFSA) has recently produced guidance for the risk assessment of nanoscience and nanotechnology applications in the food and feed chain [320]. Moreover, an effort should be made to familiarize the public consumer with active food packaging and increase their acceptance of such an innovation. This review contributes to increasing the knowledge of the available sustainable biodegradable active packaging and highlights the increasing number of investigations and the increasing industrial interest in the area, as well as further developments needed.