Chromatographic Analysis of Aﬂatoxigenic Aspergillus ﬂavus Isolated from Malaysian Sweet Corn

: High-performance liquid chromatography (HPLC) provides a quick and efﬁcient tool for accurately characterizing aﬂatoxigenic and non-aﬂatoxigenic isolates of Aspergillus ﬂavus . This method also provides a quantitative analysis of AFs in Aspergillus ﬂavus. The method’s recovery was assessed by spiking a mixture of AF at different concentrations to the testing medium. The validity of the method was conﬁrmed using aﬂatoxigenic and non-aﬂatoxigenic strains of A. ﬂavus . The HPLC system, coupled with a ﬂuorescence detector and post-column photochemical reactor, showed high sensitivity in detecting spiked AFs or AFs produced by A. ﬂavus isolates. Recovery from medium spiked with 10, 20, 60, and 80 ppb of AFs was found to be 73–86% using this approach. For AFB 1 and AFB 2 , the limit of detection was 0.072 and 0.062 ppb, while the limit of quantiﬁcation was 0.220 and 0.189 ppb, respectively. The AFB 1 concentrations ranged from 0.09 to 50.68 ppb, while the AFB 2 concentrations ranged between 0.33 and 9.23 ppb. The ﬁndings showed that six isolates produced more AFB 1 and AFB 2 than the acceptable limit of 5 ppb. The incidence of aﬂatoxigenic isolates of A. ﬂavus in sweet corn and higher concentrations of AFB 1 and AFB 2 emphasize the need for ﬁeld trials to explore their real potential for AF production in corn.


Introduction
Aspergillus flavus is a ubiquitous saprophytic or parasitic fungus commonly found in decaying vegetation, crops, and seeds. Contamination of cereal crops by A. flavus is one of the worst food security problems due to its acute and chronic effects on humans and animals [1]. Together with A. parasiticus, A. flavus is the largest agricultural fungal species, producing aflatoxins (AFs) in corn, peanuts, and nuts [2]. Tropical conditions, including high temperatures, high humidity, heavy rains, and floods, cause mycological dissemination and AF production [3]. Due to Malaysia's tropical environment, the temperature remains between 28 and 31 • C and humidity between 60 and 80%, providing suitable conditions for A. flavus to contaminate cereal crops. The colonization of A. flavus on ripening corn results in contamination with AFs. As climate change progresses, A. flavus is predicted to extend its growing area, contributing to an increasing threat of AF infection throughout the globe [4,5]. AFs are secondary metabolites that cause severe disease in humans and animals [6,7]. While approximately 13 types of AFs are currently identified, AFB 1 , AFB 2 , AFG 1 , and AFG 2 are the most harmful to humans and animals, predominantly found in foods and feeds. The letters "B" and "G" represent their blue and green fluorescence released under ultraviolet (UV) radiation, while the digits show their major and minor compounds. Furthermore, AFB 2 and AFG 2 are the dihydroxy byproducts of AFB 1 and AFG 1 [8,9]. AFs possess specific fluorescence activities due to their oxygenated pentaheterocyclic framework known as the coumarin nucleus ( Figure 1). The tendency to fluoresce has motivated several analytical approaches to detect and quantify such toxins [10]. Owing to the lack of double bonds within the furan rings, AFB 2 and AFG 2 provide a greater fluorescence quantum output than both AFB 1 and AFG 1 [11].
Separations 2021, 8, x FOR PEER REVIEW 2 of 11 minor compounds. Furthermore, AFB2 and AFG2 are the dihydroxy byproducts of AFB1 and AFG1 [8,9]. AFs possess specific fluorescence activities due to their oxygenated pentaheterocyclic framework known as the coumarin nucleus ( Figure 1). The tendency to fluoresce has motivated several analytical approaches to detect and quantify such toxins [10].
Owing to the lack of double bonds within the furan rings, AFB2 and AFG2 provide a greater fluorescence quantum output than both AFB1 and AFG1 [11]. The International Agency for Research on Cancer (IARC) classified AFB1 as a Group 1 human carcinogen, causing liver cancer in humans [12]. This active site might be involved in a reduction reaction, leading to a significant shift in its functions [13,14]. AFB1 is usually heat-resistant and can tolerate high temperatures during cooking or sterilization processes. In human food, the presence of AFB1 can cause acute and chronic health effects, including immunosuppressive diseases, stunting in children, hepatic carcinoma (HCC), and even death. Inhaling AF-contaminated dust may induce tumors in human and animal respiratory tracts [15]. Moreover, AFB1 is directly linked to jaundice, diarrhea, depression, low-grade fever, and liver cancer. The communities of A. flavus existing in diverse agroecosystems are composite sets of different populations.
Therefore, understanding the ability of A. flavus to produce AFs is an essential factor in the forecast of the prevalence and intensity of AF contamination. Previous studies presumed that A. flavus produces only AFB1 and AFB2; recent studies have found that few strains of A. flavus produce AFG1 and AFG2 [16,17]. Several strategies, including fungal cultures and molecular marker-based methods, have been developed to identify and distinguish aflatoxigenic and non-aflatoxigenic A. flavus strains [18,19]. Culture-based methods are rapid, cost-effective, and involve limited research expertise, however, the development of new analytical methods could be considered a promising alternative to culturebased methods, as they may have a broad range of applications, a shorter total analysis time, and high efficiency, sensitivity, specificity, and reproducibility. High-performance liquid chromatography (HPLC) is an advanced analytical separation method since it perfectly complements other known chromatographic techniques (conventional column chromatography, thin-layer chromatography, and gas chromatography). Furthermore, HPLC, equipped with a fluorescence detector (FLD) and post-column photochemical reactor, ensures a relatively fast, efficient, sensitive, specific, and global method for the detection of AF. Therefore, the HPLC-FLD system is a very versatile separation/detection system that allows the identification of chemical compounds. Given the advantages of HPLC-FLD, this study aimed to develop an analytical method for the identification of AFproducing isolates of A. flavus, isolated from Cameron Highlands' sweet corn [20], and the quantification of these different AFs. The International Agency for Research on Cancer (IARC) classified AFB 1 as a Group 1 human carcinogen, causing liver cancer in humans [12]. This active site might be involved in a reduction reaction, leading to a significant shift in its functions [13,14]. AFB 1 is usually heat-resistant and can tolerate high temperatures during cooking or sterilization processes. In human food, the presence of AFB 1 can cause acute and chronic health effects, including immunosuppressive diseases, stunting in children, hepatic carcinoma (HCC), and even death. Inhaling AF-contaminated dust may induce tumors in human and animal respiratory tracts [15]. Moreover, AFB 1 is directly linked to jaundice, diarrhea, depression, low-grade fever, and liver cancer. The communities of A. flavus existing in diverse agroecosystems are composite sets of different populations.
Therefore, understanding the ability of A. flavus to produce AFs is an essential factor in the forecast of the prevalence and intensity of AF contamination. Previous studies presumed that A. flavus produces only AFB 1 and AFB 2 ; recent studies have found that few strains of A. flavus produce AFG 1 and AFG 2 [16,17]. Several strategies, including fungal cultures and molecular marker-based methods, have been developed to identify and distinguish aflatoxigenic and non-aflatoxigenic A. flavus strains [18,19]. Culture-based methods are rapid, cost-effective, and involve limited research expertise, however, the development of new analytical methods could be considered a promising alternative to culture-based methods, as they may have a broad range of applications, a shorter total analysis time, and high efficiency, sensitivity, specificity, and reproducibility. Highperformance liquid chromatography (HPLC) is an advanced analytical separation method since it perfectly complements other known chromatographic techniques (conventional column chromatography, thin-layer chromatography, and gas chromatography). Furthermore, HPLC, equipped with a fluorescence detector (FLD) and post-column photochemical reactor, ensures a relatively fast, efficient, sensitive, specific, and global method for the detection of AF. Therefore, the HPLC-FLD system is a very versatile separation/detection system that allows the identification of chemical compounds. Given the advantages of HPLC-FLD, this study aimed to develop an analytical method for the identification of AF-producing isolates of A. flavus, isolated from Cameron Highlands' sweet corn [20], and the quantification of these different AFs.

Chemicals and Reagents
Standards including AFB 1 , AFB 2 , AFG 1 , and AFG 2 were purchased from Sigma-Aldrich (St. Louis, MO, USA). HPLC-grade methanol and acetonitrile were acquired from Merck KGaA (Darmstadt, Germany) and used to prepare the mobile phase. HPLC-grade chloroform was obtained from Sigma-Aldrich (St. Louis, MO, USA) and used for the extraction of the AFs. Ultra-pure water was acquired from Elga LabWater (High Wycombe, UK) and used to prepare the mobile phase and culture media. Whatman filters with 0.2 µm pore size and a polytetrafluoroethylene (PTFE) syringe filter (0.22 µm with 13 mm diameter) were obtained from HmbG Chemicals (Hamburg, Germany). Potato dextrose agar (PDA) was bought from Oxoid Ltd. (Basingstoke, UK).

Aflatoxin Standards Preparation
Standard solutions of AFB 1 and AFB 2 were prepared in acetonitrile at a fixed volume of 10 ppb (parts per billion) using a slightly modified method of the Association of Official Analytical Chemists (AOAC) [21,22]. In preparing 10 ppb of each AF stock standard, 10 mg of individual AF was dropped in 100 mL volumetric flasks. In each volumetric flask, 50 mL acetonitrile was poured and stirred for 30 s. Next, a 10 mL solution was emptied into a volumetric flask and mixed with the acetonitrile. The working solutions (individual and mixture solutions) were prepared with acetonitrile and retained in HPLC vials (Thermo Scientific, Milford, MA, USA) at −4 • C. Standard solutions of AFs were developed by dissolving the mobile phase's working solutions in the calibration curve.

Strains of Aspergillus Flavus
Forty isolates of A. flavus were used in this study. For the recovery experiments, A. flavus NRRL 21,882 was used as a non-aflatoxigenic strain as it cannot produce AFs due to the deletion or mutation of gene clusters responsible for AF biosynthesis [23,24]. Alternatively, ATCC 200026 (synonym: NRRL 3357) was employed as a positive control since it produces AFB 1 and AFB 2 in laboratories and fields [25]. The A. flavus isolates were grown for 7 d at 30 ± 2 • C. PDA was preferred for this study, as it is rich in carbohydrate content and possesses an acidic pH (5.1), providing favorable conditions for A. flavus to grow and produce AFs [23]. Following seven days of incubation, conidia were harvested, counted, and adjusted to 1 × 10 6 using a hemocytometer and sterile distilled water. Spore suspensions of A. flavus were preserved at −4 • C until further analysis.

Inoculation of Aspergillus Flavus
Spore suspensions were used as an inoculum source throughout the inoculation process. Forty isolates of A. flavus with negative control (NRRL 21,882) and positive control (NRRL 3357) were inoculated in petri dishes (100 mm × 20 mm), comprising roughly 25 mL PDA. After inoculation, the dishes were incubated at 30 ± 2 • C for seven days.

Extraction of Aflatoxins
A flowchart for the extraction of AFs from A. flavus culture is presented in Figure 2. AFs were extracted from A. flavus cultures using a solid-liquid extraction method. We transferred 10 mL of ultrapure water into each culture, and spores were harvested by gently scratching the mycelial surface and transferred into 50 mL conical centrifuge tubes. Spore suspensions were then vortexed (LMS Co., Ltd., Tokyo, Japan) for 30 s, before 1 mL was emptied into new 15 mL centrifuge tubes, mixed with 1.5 mL chloroform, and vortexed for 30 s. Next, the mixture was subjected to centrifugation (Sartorius, Germany) for 5 min at 13,000× g. The residual from the bottom phase was shifted into new HPLC vials. An additional 1.5 mL chloroform was used to extract the sample residue and recover traces of AFs following the first extraction. The chloroform extracts were mixed and vaporized to achieve adequate aridity. The extract was then diluted with a mobile phase of 1 mL and filtered into an HPLC vial using a PTFE syringe filter. traces of AFs following the first extraction. The chloroform extracts were mixed and vaporized to achieve adequate aridity. The extract was then diluted with a mobile phase of 1 mL and filtered into an HPLC vial using a PTFE syringe filter.

High-Performance Liquid Chromatography Procedure
In this study, samples were tested for AFs by a reversed-phase HPLC system (Waters 600, Milford, MA, USA) equipped with a fluorescence detector (FLD) (Waters 2475, Milford, MA, USA) and post-column photochemical reactor. The separation was accomplished through a C18 column (Ymc Triart, 5 µM, 12 nm, 150mm × 4.6 mm; YMC, Tokyo, Japan) at 40 °C. The excitation and emission wavelengths were 360 nm and 440 nm, respectively. A mobile phase of acetonitrile (CH3CN)/methanol (CH3OH)/distilled water (H2O) (10:35:55 v/v/v) with a flow rate of 1 mL/min was employed to elute the samples. The mobile phase (acetonitrile, methanol, and dH2O) was filtered using a Whatman filter (0.2 µM × 47 mm diameter; Merck, Darmstadt, Germany) and degassed for 30 min in an ultrasonic bath (Power sonic 420, Seoul, Korea). The volume of injection was 20 µL. The data software Empower-2 Chromatography (Waters, Milford, MA, USA) was used for data acquisition and data processing.

Validation of HPLC
The HPLC process was validated by assessing recovery, accuracy, linearity, and sensitivity under the AOAC guidelines [21], with minor changes. A mixture of known concentrations of AFB1 and AFB2 (10, 20, 60, and 80 ppb) was spiked into the blank samples to validate recovery. The spike of each concentration was achieved in triplicate, and the tests were conducted in triplicate each day for three consecutive days. Accuracy was observed through reliability. Reliability was measured by the relative standard deviation (RSD) of spiked toxins recurrent on the first day. Blank samples were developed by inoculating the negative control (NRRL 21,881) on PDA, harvested, and analyzed by HPLC coupled with FLD and a post-column photochemical reactor. The selectivity of the method was confirmed, as the chromatographic peaks did not conflict with the retention time of the AFs. The linearity for AFs was observed in triplicate, ranging between 10 and 80 ppb. The calibration curve for each concentration (10, 20, 60, and 80 ppb) was constructed employing the peak area of the AF against the analyte concentration. The linearity was assessed through the correlation coefficient (R 2 ), interception (y), and slope (s) of the regression line. The sensitivity of the HPLC method was assessed by evaluating the LOD and LOQ through the following equation: LOD = 3.3 σ/s and LOQ = 10 σ/s.
where σ is the standard deviation of blank samples, and s is the calibration curve slope.

High-Performance Liquid Chromatography Procedure
In this study, samples were tested for AFs by a reversed-

Validation of HPLC
The HPLC process was validated by assessing recovery, accuracy, linearity, and sensitivity under the AOAC guidelines [21], with minor changes. A mixture of known concentrations of AFB 1 and AFB 2 (10, 20, 60, and 80 ppb) was spiked into the blank samples to validate recovery. The spike of each concentration was achieved in triplicate, and the tests were conducted in triplicate each day for three consecutive days. Accuracy was observed through reliability. Reliability was measured by the relative standard deviation (RSD) of spiked toxins recurrent on the first day. Blank samples were developed by inoculating the negative control (NRRL 21,881) on PDA, harvested, and analyzed by HPLC coupled with FLD and a post-column photochemical reactor. The selectivity of the method was confirmed, as the chromatographic peaks did not conflict with the retention time of the AFs. The linearity for AFs was observed in triplicate, ranging between 10 and 80 ppb. The calibration curve for each concentration (10, 20, 60, and 80 ppb) was constructed employing the peak area of the AF against the analyte concentration. The linearity was assessed through the correlation coefficient (R 2 ), interception (y), and slope (s) of the regression line. The sensitivity of the HPLC method was assessed by evaluating the LOD and LOQ through the following equation: LOD = 3.3 σ/s and LOQ = 10 σ/s.
where σ is the standard deviation of blank samples, and s is the calibration curve slope.

Statistical Analysis
The HPLC system has been enhanced and verified using statistical analysis to improve the recovery of the AFs and avoid chemical loss. The quantities were averaged and shown as a mean ± standard error. The peak areas of the AFs were separated without any interruption. The significance (p < 0.05) of the data was analyzed through the ANOVA test (analysis of variance) with a confidence interval of 95% using the SPSS ® version 25 software (IBM SPSS ® Inc., Chicago, IL, USA). The following equation determines the relative standard deviation (RSD).
where S represents the standard deviation, while x represents the mean of the data.

Aspergillus Flavus on PDA
On PDA, A. flavus isolates produced olive-green conidia, which dominated the appearance of the colony. After three days of incubation, sporulation began from the center and progressed radially, covering the colony's surface. The conidia produced had a yellowish to olive color. As the sporulation spread outwards, it gave a characteristic white border encircling the sporulating mycelia. The white border eventually covered as the entire mycelia continued to sporulate and produce more conidia by day seven. The colonies produced brown or colorless exudates (droplets). Some isolates produced a compact mass of dark brown fungal mycelia (sclerotia). The reverse of the A. flavus colonies was pale in color. As the colony grew, it slightly raised as the mycelia piled, and the center became floccose and rough (Figure 3).

Statistical Analysis
The HPLC system has been enhanced and verified using statistical analysis to improve the recovery of the AFs and avoid chemical loss. The quantities were averaged and shown as a mean ± standard error. The peak areas of the AFs were separated without any interruption. The significance (p < 0.05) of the data was analyzed through the ANOVA test (analysis of variance) with a confidence interval of 95% using the SPSS ® version 25 software (IBM SPSS ® Inc., Chicago, IL, USA). The following equation determines the relative standard deviation (RSD).
where S represents the standard deviation, while x represents the mean of the data.

Aspergillus Flavus on PDA
On PDA, A. flavus isolates produced olive-green conidia, which dominated the appearance of the colony. After three days of incubation, sporulation began from the center and progressed radially, covering the colony's surface. The conidia produced had a yellowish to olive color. As the sporulation spread outwards, it gave a characteristic white border encircling the sporulating mycelia. The white border eventually covered as the entire mycelia continued to sporulate and produce more conidia by day seven. The colonies produced brown or colorless exudates (droplets). Some isolates produced a compact mass of dark brown fungal mycelia (sclerotia). The reverse of the A. flavus colonies was pale in color. As the colony grew, it slightly raised as the mycelia piled, and the center became floccose and rough (Figure 3).

LOD and LOQ for Aflatoxin
The LOD and LOQ for AFs were used to validate the HPLC system's performance. A standard solution of 20-80 ppb/mL of AFB1 and AFB2 was used to construct a four-point calibration curve. The LOD for AFB1 was 0.072 ppb, while for AFB2 it was 0.062 ppb. In contrast, the LOQ for AFB1 was 0.220 ppb, while for AFB2 it was 0.180 ppb (Table 1).

LOD and LOQ for Aflatoxin
The LOD and LOQ for AFs were used to validate the HPLC system's performance. A standard solution of 20-80 ppb/mL of AFB 1 and AFB 2 was used to construct a four-point calibration curve. The LOD for AFB 1 was 0.072 ppb, while for AFB 2 it was 0.062 ppb. In contrast, the LOQ for AFB 1 was 0.220 ppb, while for AFB2 it was 0.180 ppb (Table 1).

Linearity
The linearity was determined by four-point calibration curves over the range of 10 to 80 ppb for individual AFs to determine a relative association between response and AF concentration. Calibration curves were constructed by plotting the peak area (y) against the AF concentration (x) (Figure 4). Linear regression (R 2 ) ranged between 0.9952 and 0.9960 for the FLD detector, representing enhanced linearity for AFB 1 and AFB 2 ( Table 1).

Linearity
The linearity was determined by four-point calibration curves over the range of 10 to 80 ppb for individual AFs to determine a relative association between response and AF concentration. Calibration curves were constructed by plotting the peak area (y) against the AF concentration (x) (Figure 4). Linear regression (R 2 ) ranged between 0.9952 and 0.9960 for the FLD detector, representing enhanced linearity for AFB1 and AFB2 (Table 1).

Recovery of Aflatoxins
The percentage recovered of the analytes when the test sample is assessed with the complete method is known as the recovery of the method [26]. Table 2 represents the recovery percentage of AFB1 and AFB2 at different concentrations of a spike in culture conditions. Recovery of AFs exhibited the same retention time with a total recovery of 73-86%.

Recovery of Aflatoxins
The percentage recovered of the analytes when the test sample is assessed with the complete method is known as the recovery of the method [26]. Table 2 represents the recovery percentage of AFB 1 and AFB 2 at different concentrations of a spike in culture conditions. Recovery of AFs exhibited the same retention time with a total recovery of 73-86%.

Quantification of AFB 1 and AFB 2
Regarding AFB 1 quantification, 24 strains of A. flavus produced AFB 1 ranging from 0.09 to 50.68 ppb, while the remaining 16 strains did not produce AFB 1 (Table 3). In these AFB 1 -producing strains, two strains surpassed the maximum acceptable limit of 5 ppb.
Alternatively, 22 strains were found to produce AFB 2 with levels of 0.33 to 9.23 ppb. The results indicated that 6 of the 40 isolates produced AFB 1 and AFB 2 in quantities higher than the permissible limit of 5 ppb in food. Moreover, the positive control (NRRL 3357) produced both AFB 1 and AFB 2 with concentrations of 3.96 to 1.14 ppb. In contrast, the negative control (NRRL 21,882) did not produce any type of AFs (AFB 1 , AFB 2 ) when cultured on the PDA medium, as seen in previous studies [23,27].

Discussion
The contamination of sweet corn with AFs represents one of the worst global food security problems, due to their acute and chronic adverse effects on humans and animals [28]. A. flavus is the leading food contaminant since it can produce AFs and persists as a pathogen in both pre-and post-harvest food supply [26]. The growth of A. flavus and AF production are linked to various environmental factors, including water activity, temperature, pH, and content of CO 2 [1,29,30]. In Malaysia, the environmental conditions are characterized by high temperature, high humidity, and inadequate storage practices that contribute to the potential for a substantial exposure of the Malaysian people to AFs. Recent studies have found that species of A. flavus and A. niger are the most common fungi isolated from contaminated cereal crops [31]. The results of the current study demonstrate that among the 40 isolates of A. flavus, 24 isolates were aflatoxigenic, producing AFB 1 and AFB 2 , while the remaining 18 isolates were non-aflatoxigenic. This study also displayed that all aflatoxigenic and non-aflatoxigenic isolates produced olive-green colonies on PDA medium and rapidly grow at optimum temperature (25-32 • C). This observation suggests the presence of aflatoxigenic and non-aflatoxigenic isolates in A. flavus species. The results also revealed that the A. flavus isolates producing small sclerotia could produce both AFB 1 and AFB 2 , while the A. flavus isolates producing large sclerotia did not synthesize AFB 1 and AFB 2 .
The results obtained from the current study demonstrated significant variability in the AF-producing potential of A. flavus. According to Bandyopadhyay et al. [32] and Sarma et al. [33], the size and formation of sclerotia are strongly related to the aflatoxigenicity of A. flavus isolates. It has been identified that all S-type A. flavus strains producing small sclerotia (≤400 µM in diameter) are aflatoxigenic, whereas the L-type strains producing larger sclerotia (≥400 µM in diameter) include both aflatoxigenic and non-aflatoxigenic strains. Similarly, Mellon [34] has reported a close relationship between small sclerotia and AF production. On the contrary, Barrett and Bevis [35] and Ehrlich et al. [36] found the highest level of AFs in isolates having large sclerotia. Hence, the relationship between AF production and sclerotial size and was observed in this study. This method has shown efficient separation capacity and selectivity, allowing the simultaneous quantification of the AFB 1 and AFB 2 produced by aflatoxigenic strains. The FLD detection method proficiently distinguishes the peaks of AFB 1 and AFB 2 in the same HPLC run without interruption. Besides that, method validation is a vital criterion for conducting the HPLC analysis [37]. LOD and LOQ were applied to validate the performance of the HPLC method. LOD is the lowest analyte concentration detected under specified laboratory conditions but not simply quantitated [38]. In contrast, LOQ is the smallest analyte concentration that can be quantified [39]. In this study, multiple concentrations of 3.0 ppb were injected to evaluate the sensitivity of FLD for detecting AFB 2 . It was noticed that FLD easily detected AFB 2 at parts per trillion (ppt) as predicted, since it lacks a double bond in furan rings. To the best of our knowledge, an LOD of 1.0-5.0 ppb is adequate for a researcher to distinguish between aflatoxigenic and non-aflatoxigenic strains of A. flavus and to quantify the concentration of AFs. In this study, we used reversed-phase chromatography in which AFs were eluted in a sequence of AFB 2 and AFB 1 ( Figure 5). The sequence has been confirmed by matching the retention time attained in the AF mixture with the retention time of the individual AFs. The extracted AFs were then identified using the FLD detector ( Figure 5). Note that AFB 2 can also be observed in low quantities while using the FLD detector as it fluoresces 40 times as higher as AFB 1 .
The percentage recovered of the analytes when the test sample was assessed with the complete method is known as method recovery [40]. FLD has detected all spiked samples in the sequence, and their mean was calculated. The recovery spectrum agreed with the criteria of AOAC and Codex Alimentarius' acceptable recovery limits. The acceptable recovery limit of the AOAC at 10 ppb is from 70 to 125%, while for Codex Alimentarius, it is 60-120% at 1−10 ppb. The results indicated that 6 of the 40 isolates had produced AFB 1 and AFB 2 in amounts higher than the maximum acceptable limit of 5 ppb in food. Therefore, further research on AFs contamination of sweet corn in the field and storage is needed to provide data on the Malaysian population's exposure towards AFs, particularly AFB 1 .
searcher to distinguish between aflatoxigenic and non-aflatoxigenic strains of A. flavus and to quantify the concentration of AFs. In this study, we used reversed-phase chromatography in which AFs were eluted in a sequence of AFB2 and AFB1 ( Figure 5). The sequence has been confirmed by matching the retention time attained in the AF mixture with the retention time of the individual AFs. The extracted AFs were then identified using the FLD detector ( Figure 5). Note that AFB2 can also be observed in low quantities while using the FLD detector as it fluoresces 40 times as higher as AFB1. The percentage recovered of the analytes when the test sample was assessed with the complete method is known as method recovery [40]. FLD has detected all spiked samples in the sequence, and their mean was calculated. The recovery spectrum agreed with the criteria of AOAC and Codex Alimentarius' acceptable recovery limits. The acceptable recovery limit of the AOAC at 10 ppb is from 70 to 125%, while for Codex Alimentarius, it is 60-120% at 1−10 ppb. The results indicated that 6 of the 40 isolates had produced AFB1 and AFB2 in amounts higher than the maximum acceptable limit of 5 ppb in food. Therefore, further research on AFs contamination of sweet corn in the field and storage is needed to provide data on the Malaysian population's exposure towards AFs, particularly AFB1.

Conclusions
In conclusion, this is the first detailed study on A. flavus associated with sweet corn collected from the Cameron Highlands, Malaysia. This study demonstrated that an HPLC instrument (Waters 600, USA) coupled with a fluorescence detector (Waters 2475, USA) assured precision and linearity in the quantitative determination of AFs produced by aflatoxigenic A. flavus isolates. Chloroform was used for the extraction of AFs to prevent emulsion production-a two-layer mixture with AF existing in the chloroform layer, minimizing toxin loss and leaving other substances in the aqueous layer. Peaks of AFB1 and AFB2 were differentiated within 15 min with excellent selectivity, linearity, and recovery. AFB1 was detected in 24 of 40 A. flavus isolates ranging from 0.09 to 50.68 ppb, and 22

Conclusions
In conclusion, this is the first detailed study on A. flavus associated with sweet corn collected from the Cameron Highlands, Malaysia. This study demonstrated that an HPLC instrument (Waters 600, USA) coupled with a fluorescence detector (Waters 2475, USA) assured precision and linearity in the quantitative determination of AFs produced by aflatoxigenic A. flavus isolates. Chloroform was used for the extraction of AFs to prevent emulsion production-a two-layer mixture with AF existing in the chloroform layer, minimizing toxin loss and leaving other substances in the aqueous layer. Peaks of AFB 1 and AFB 2 were differentiated within 15 min with excellent selectivity, linearity, and recovery. AFB 1 was detected in 24 of 40 A. flavus isolates ranging from 0.09 to 50.68 ppb, and 22 isolates were found to be producing AFB 2 ranging between 0.33 and 9.23 ppb. The results indicated that 6 of the 40 strains had produced AFB 1 and AFB 2 in quantities greater than the permissible limit of 5 ppb. The occurrence of AF-producing A. flavus isolates in sweet corn and the quantities of AFB 1 and AFB 2 greater than the permissible limit emphasizes the need for field trials to investigate their actual ability for AF production in corn crops.
Author Contributions: F.M.G., supervision, project administration, funding acquisition; R.K., methodology, writing-original draft preparation; N.I.P.S., conceptualization, and methodology assistance; N.A.M. review, resources, and data curation. All authors have read and agreed to the published version of the manuscript.