The Separation and Puriﬁcation of Ellagic Acid from Phyllanthus urinaria L. by a Combined Mechanochemical-Macroporous Resin Adsorption Method

: Ellagic acid is a phenolic compound that exhibits both antimutagenic and anticarcinogenic activity in a wide range of assays in vitro and in vivo. It occurs naturally in some foods such as raspberries, strawberries, grapes, and black currants. In this study, a valid and reliable method based on mechanochemical-assisted extraction (MCAE) and macroporous adsorption resin was developed to extract and prepare ellagic acid from Phyllanthus urinaria L. (PUL). The MCAE parameters, acidolysis, and macroporous adsorption resin conditions were investigated. The key MCAE parameters were optimized as follows: the milling time was 5 min, the ball mill speed was 100 rpm, and the ball mill ﬁlling rate was 20.9%. Sulfuric acid with a concentration of 0.552 mol/L was applied for the acidolysis with the optimized acidolysis time of 30 min and acidolysis temperature of 40 ◦ C. Additionally, the XDA-8D macroporous resin was chosen for the puriﬁcation work. Both the static and dynamic adsorption tests were carried out. Under the optimized conditions, the yield of ellagic acid was 10.2 mg/g, and the content was over 97%. This research provided a rapid and efﬁcient method for the preparation of ellagic acid from the cheaply and easily obtained PUL. Meanwhile, it is relatively low-cost work that can provide a technical basis for the comprehensive utilization of PUL.


Introduction
Ellagic acid (C 14 H 6 O 8 , Figure 1) is an acidic hydrolysis product of polymeric ellagitannins. It is a natural polyphenolic compound that is present in various vegetables, fruits, herbs, and nuts, such as raspberries, strawberries, walnuts, grapes, and black currants [1,2]. At present, the most important pharmacological activity of ellagic acid is its antioxidant activity, which mainly depends on its basic structure containing four hydroxyl groups that are responsible for scavenging superoxide and hydroxyl anion free radicals [3][4][5]. In addition, ellagic acid has been found to have antimutagenic [6], anticarcinogenic [7][8][9][10][11], antifibrosis [9], and anti-inflammatory effects [12,13]. Furthermore, it can also improve Alzheimer's disease-mediated dementia by suppressing oxidative and inflammatory cell damage and improving antioxidant content. Ellagic acid inhibits cognitive abnormality following traumatic brain injury (TBI) in rats through its anti-inflammatory and antioxidant properties [14]. At present, three main methods are utilized for preparing ellagic acid: plant extraction [15,16], chemical synthesis [17], and enzymatic degradation [18]. Among them, the extraction of ellagic acid from natural plant resources is thought to be one of the most important ways due to its relatively high abundant content and environmental friendliness. Phyllanthus urinaria L. (PUL), belonging to the Euphorbiaceae family, is widely distributed in tropical and subtropical regions of Asian countries [19,20]. The dried whole plant of PUL, also named "pearl grass", "nocturnal grass", and "yin-yang grass", is a traditional Chinese medicine for the treatment of several diseases, including dysentery, jaundice, urinary tract infection, and malnutritional stagnation [21][22][23]. Pharmacological studies have shown that PUL possesses good biological activities such as anti-viral [24][25][26], anti-tumor [27], anti-thrombosis [28], hepatoprotective [29], antioxidant [30,31], anti-inflammatory [32] and immunomodulatory activities [33]. Most of the reported ingredients in PUL were tannins, lignans, flavonoids, phenolics, and terpenoids [23,29,30]. Ingredient research also showed that PUL is rich in ellagitannins, which are the main anti-hepatitis B virus active ingredients [22,24] and the main sources of ellagic acid.
In this work, a reliable method based on mechanochemical-assisted extraction (MCAE) and macroporous adsorption resin was developed to extract, separate and purify ellagic acid from PUL. To promote the yield of ellagic acid, the key mechanochemistry ball milling parameters were optimized. Additionally, the different kinds of macroporous resin were further optimized to purify the ellagic acid by the static and dynamic adsorption tests. To date, no separation of ellagic acid from PUL based on mechanochemicalassisted extraction and macroporous adsorption resin has been reported. This research provided both an efficient method to obtain ellagic acid and the comprehensive utilization of cheaply and easily obtained PUL.

Materials and Chemicals
The dried PUL was purchased from Tongrentang, Hangzhou City, Zhejiang Province (Hanghzou, China) and stored at room temperature before analysis. The standard ellagic acid (≥98%) was purchased from Shanghai Yuanye Bio-Technology Co., Ltd. (Shanghai, China).
HPLC-grade acetonitrile, methanol and ethanol were supplied by Merck (Darmstadt, Germany). HPLC-grade formic acid was bought from Shanghai Aladdin Bio-Chem Technology Co., Ltd. (Shanghai, China). Ultrapure water (18.2 MΩ) was purified by Barnstead TII super Pure Water System (Boston, MA, USA). Other reagents used in this experiment were all analytical grade and were obtained from Yongda Chemical Reagent Company (Tianjin, China).

Mechanochemical-Assisted Extraction Procedure
The dried PUL was fully ground and passed through an 80-mesh sifter. The PUL powder (2.0 g) was added into a PM 200 planetary ball mill (grinding media: stainless steel balls of 8 mm diameter; the weight of the balls: 4.2 g; two drums at 50 mL each; the volume of the load/drum ratio: 1:2). Then, the ground mixture (1.0 g) was extracted with 10 mL of 50% ethanol in a 50 mL flask at 30 °C for 30 min under an ultrasonic bath. The supernatant was collected as the ellagitannin extract. Phyllanthus urinaria L. (PUL), belonging to the Euphorbiaceae family, is widely distributed in tropical and subtropical regions of Asian countries [19,20]. The dried whole plant of PUL, also named "pearl grass", "nocturnal grass", and "yin-yang grass", is a traditional Chinese medicine for the treatment of several diseases, including dysentery, jaundice, urinary tract infection, and malnutritional stagnation [21][22][23]. Pharmacological studies have shown that PUL possesses good biological activities such as anti-viral [24][25][26], anti-tumor [27], anti-thrombosis [28], hepatoprotective [29], antioxidant [30,31], antiinflammatory [32] and immunomodulatory activities [33]. Most of the reported ingredients in PUL were tannins, lignans, flavonoids, phenolics, and terpenoids [23,29,30]. Ingredient research also showed that PUL is rich in ellagitannins, which are the main anti-hepatitis B virus active ingredients [22,24] and the main sources of ellagic acid.
In this work, a reliable method based on mechanochemical-assisted extraction (MCAE) and macroporous adsorption resin was developed to extract, separate and purify ellagic acid from PUL. To promote the yield of ellagic acid, the key mechanochemistry ball milling parameters were optimized. Additionally, the different kinds of macroporous resin were further optimized to purify the ellagic acid by the static and dynamic adsorption tests. To date, no separation of ellagic acid from PUL based on mechanochemical-assisted extraction and macroporous adsorption resin has been reported. This research provided both an efficient method to obtain ellagic acid and the comprehensive utilization of cheaply and easily obtained PUL.

Materials and Chemicals
The dried PUL was purchased from Tongrentang, Hangzhou City, Zhejiang Province (Hanghzou, China) and stored at room temperature before analysis. The standard ellagic acid (≥98%) was purchased from Shanghai Yuanye Bio-Technology Co., Ltd. (Shanghai, China).
HPLC-grade acetonitrile, methanol and ethanol were supplied by Merck (Darmstadt, Germany). HPLC-grade formic acid was bought from Shanghai Aladdin Bio-Chem Technology Co., Ltd. (Shanghai, China). Ultrapure water (18.2 MΩ) was purified by Barnstead TII super Pure Water System (Boston, MA, USA). Other reagents used in this experiment were all analytical grade and were obtained from Yongda Chemical Reagent Company (Tianjin, China).

Mechanochemical-Assisted Extraction Procedure
The dried PUL was fully ground and passed through an 80-mesh sifter. The PUL powder (2.0 g) was added into a PM 200 planetary ball mill (grinding media: stainless steel balls of 8 mm diameter; the weight of the balls: 4.2 g; two drums at 50 mL each; the volume of the load/drum ratio: 1:2). Then, the ground mixture (1.0 g) was extracted with 10 mL of 50% ethanol in a 50 mL flask at 30 • C for 30 min under an ultrasonic bath. The supernatant was collected as the ellagitannin extract.

Acidolysis Experiment
The acid hydrolysis agent (1.5 mL) was added to the ellagitannin extract. The mixture was placed in a 40 • C water bath, heated and stirred for 30 min. The supernatant was  Table 1. To remove some water-soluble impurities and suspended material, resins were soaked in deionized water. Then, they were transferred into 95% ethanol for 24 h to swell completely. After washing with deionized water, resins were separately immersed in 5% (w/v) NaOH for 24 h, followed by rinsing with deionized water to a neutral pH. Finally, the macroporous resins were immersed in 5% (v/v) HCl for 24 h and rinsed with deionized water again.

Static Adsorption Tests
Different kinds of resins were compared for their separation capacity through static adsorption tests. The general experimental procedure was as follows: Pretreated resin (1.0 g) was added to a 50 mL flask, then 20.0 mL of 0.09 mg/mL crude ellagic acid solution was added. The flask was shaken in a shaker at 25 • C with 100 rpm for 24 h. The content of the ellagic acid in the adsorption solution was determined and calculated by the UPLC method.

Sorption Kinetics Tests
Sorption kinetics tests were performed to choose the most efficient resin. Similarly, pretreated resin (1.0 g) was added to a 50 mL flask, then 20.0 mL of 0.09 mg/mL crude ellagic acid solution was added. The flask was shaken in a shaker at 25 • C with 100 rpm for 24 h. Every hour, 1 mL of extract was pipetted out to perform UPLC determination.
The adsorption properties including the adsorption capacity, adsorption rate, desorption ratio and recovery rate of each resin were quantified according to the following equations: where W was the adsorption capacity at adsorption equilibrium (mg/g dry resin), and ρ o , ρ e and ρ d were the initial, absorption equilibrium and desorption concentrations of analyte in the solutions, respectively (mg/mL). V was the volume of the adsorption solution (mL), and m was the dry weight of the resin (g). E was the adsorption rate (%), D was the desorption rate (%) and R was the recovery rate (%) of the resin.

Dynamic Adsorption Tests
Dynamic adsorption tests were carried out as follows: 60 mL of XDA-8D resins were packed in the column (20 mm × 300 mm), which was loaded with the crude ellagic acid solution, by the wet method. Then, 120 mL of deionized water was loaded to rinse the resins with the flow rate at 1.0 BV/h to make the eluant and extract mix together. After adsorptive equilibrium, different concentrations of ethanol (10%, 20%, 30%, 40%, 50%, 60%, 70%, 80% and 90%) were utilized to desorb the ellagic acid at a constant flow rate of 1.0 BV/h. The elution volume of each concentration was constant by being maintained at 3.0 BV. The contents of ellagic acid in each desorption solution were determined by UPLC. The proton 1 H and carbon 13 C NMR spectra of the ellagic acid were obtained at 308 K using a Bruker AVANCE III 600 MHz NMR spectrometer (Bruker, Billerica, MA, USA). The chemical shifts (δ) in the NMR spectra were recorded in ppm with the solvent peak as the reference. The MS analysis was carried out on a micrOTOF-Q II mass spectrometer (Bruker Daltonics, Bremen, Germany) equipped with an ESI source. The ESI source parameters were as follows: the dry gas (N 2 ) flow rate was 6.0 L/min, the nebulizer gas (N 2 ) pressure was 0.8 bar, the dry gas temperature was 200 • C, and the capillary voltage was 2800 V in the negative mode.

Optimization of the MCAE Procedure
The mechanical force could reduce the particle size of herbal plant powder and destroy the cell wall structure, which increases the release of chemical constituents. In this research, the mechanochemistry ball milling method was applied to the extraction of ellagitannin from PUL. Compared with the traditional extraction method, the ball milling process could effectively increase the peak area of ellagitannin compounds.
To obtain a higher yield of ellagitannin, the key ball milling parameters including milling time, milling speed, and mill filling rate were optimized. To evaluate the influence of milling time on the yield of ellagitannin, the milling time was investigated at 5 min, 10 min and 15 min, respectively. With the extension of milling time, the peak areas of three compounds (corilagin, geraniin, and ellagic acid) generally showed a downward trend, shown in Figure 2A. The possible reason was that the longer milling time resulted in the accumulation of heat in the ball milling tank, which destroyed the compound structural units and led to the oxidation and partial decomposition of the ellagitannin compound. As a result, the milling time of 5 min was preferred.   Ball milling speed is a crucial factor for MCAE. The effect of ball milling speed on the extraction yield of ellagitannin from PUL was shown in Figure 2B. Three speeds including 100 rpm, 200 rpm and 300 rpm were investigated. It was clearly seen that at the ball milling speed of 100 rpm, the yield of the three compounds (corilagin, geraniin, and ellagic acid) reached the maximum value. With increases in ball milling speed, the peak areas of corilagin and geraniin did not change significantly. Generally speaking, the MCAE of the ball mill can continuously destroy cell walls and promote the reaction of bioactive substances with solid phase reagents, thereby greatly improving the extraction efficiency. However, the ball milling speed did not further improve the entire extraction process at the speed of 200 rpm and 300 rpm. Hence, 100 rpm was chosen for the optimal ball milling parameter.
The ball mill filling rates were another factor that influenced the yield of ellagitannin. The filling rates at 5.2%, 10.5% and 20.9% were investigated and the results were shown in Figure 2C. Under the optimal milling time and ball milling speed, with the increase of the filling rate, the peak areas of geranium and ellagic acid showed an overall upward trend, while the peak area of ellagic acid increased significantly. It indicated that the mechanical force in the ball milling tank increased while the increased filling rate correspondingly increased the wall-breaking effect of the plant cells, and more ellagic acid was released. Moreover, the filling rate of 20.9% was used for the ball milling work.

Optimization of Acid Hydrolysis Conditions
Considering that ellagic acid is an acid hydrolysate of polymerized ellagitannin, the parameters of acid hydrolysis conditions, including acid hydrolysis reagent, acid hydrolysis temperature, and acid hydrolysis time were optimized in this work. Different acid hydrolysis reagents such as sulfuric acid, hydrochloric acid and formic acid were used. The yields of ellagic acid showed that sulfuric acid had a better acidolysis effect. Then, the concentration of sulfuric acid was further optimized. As shown in Figure 3A, the yield of ellagic acid increased with the increasing concentration of sulfuric acid, and the yield of ellagic acid was the highest when the concentration of sulfuric acid was 0.552 mol/L. When the concentration of sulfuric acid is higher than 0.552 mol/L, the yield of ellagic acid decreases. Hence, the concentration of sulfuric acid was selected as 0.552 mol/L. The acid hydrolysis temperature exerted a greater impact on the yield of ellagic acid. Different acid hydrolysis temperatures at 20 • C, 30 • C, 40 • C, 50 • C, 60 • C, 70 • C, 80 • C and 90 • C were investigated as shown in Figure 3B. The highest peak area of ellagic acid was obtained when the acidolysis temperature was set at 40 • C. As the temperature increased, the yield of ellagic acid increased. This was because high temperatures may increase the degradation rate of ellagitannin. However, when the temperature rose to a certain level (40 • C), the yield of ellagic acid decreased. It was speculated that excessive temperature might cause the oxidative damage of ellagic acid.
Acid hydrolysis time showed little effect on the yield of ellagic acid, shown in Figure 3C. Ellagitannin could be degraded into ellagic acid within 30 min. When the acid hydrolysis time was longer than 30 min, it remained stable. 30 min was thought to be the better acid hydrolysis time.
A low concentration of sulfuric acid leads to inadequate acidolysis and a low yield of ellagic acid. However, the yield of ellagic acid decreased and the energy consumption increased with the high concentration of sulfuric acid. Considering the sensitivity of ellagic acid to air, the excessive temperature may accelerate the oxidation of ellagic acid. Finally, the acid hydrolysis conditions are determined as follows: the concentration of sulfuric acid was 0.552 mol/L, the acidolysis time was 30 min, and the acidolysis temperature was 40 • C.
The yield and content of crude ellagic acid could be improved significantly under the optimized acidolysis conditions. As the content of ellagic acid increased, the contents of corilagin and geraniin decreased. It may be speculated that ellagitannins were more likely to be broken down into ellagic acid in an acid environment [34,35]. In previous reports, Wei [36] and Li [37] studied the extraction process of ellagic acid from muscadine and red raspberry, respectively. The contents of ellagic acid were 616.21 µg/g and 322 µg/g, which were much lower than the 10.2 mg/g in this work.  The yield and content of crude ellagic acid could be improved significantly under the optimized acidolysis conditions. As the content of ellagic acid increased, the contents of corilagin and geraniin decreased. It may be speculated that ellagitannins were more likely to be broken down into ellagic acid in an acid environment [34,35]. In previous reports, Wei [36] and Li [37] studied the extraction process of ellagic acid from muscadine and red

Screening of Optimum Resin
The adsorption and desorption of ellagic acid by different types of macroporous resins were shown in Table 2 and Figure 4. The XDA-8D type macroporous resin showed the highest adsorption rate (78.03%) of ellagic acid. Although its desorption rate was inferior to HPD450 and LXA-8 resins when the ethanol was selected as the adsorbent, XDA-8D had a higher recovery rate than other resins. As a result, XDA-8D was selected for the separation and purification of crude ellagic acid.

Screening of Optimum Resin
The adsorption and desorption of ellagic acid by different types of macroporous resins were shown in Table 2 and Figure 4. The XDA-8D type macroporous resin showed the highest adsorption rate (78.03%) of ellagic acid. Although its desorption rate was inferior to HPD450 and LXA-8 resins when the ethanol was selected as the adsorbent, XDA-8D had a higher recovery rate than other resins. As a result, XDA-8D was selected for the separation and purification of crude ellagic acid.

Static Adsorption Kinetics and Adsorption Isotherms
To enrich ellagic acid from PUL extracts using microporous resins effectively, the optimum type of microporous resin was screened first. Because the external factors have a significant effect, the resin adsorption behavior is significantly influenced by many external factors. To evaluate these effects on the resin adsorption capacity, the adsorption kinetics tests and adsorption isotherms of XDA-8D microporous resin for crude ellagic acid were carried out (Figures 5 and 6).
According to Figure 5, the adsorption rate of XDA-8D for crude ellagic acid increased to the biggest within 1 h. Then, it still maintained a fast adsorption rate within 1-5 h.

Static Adsorption Kinetics and Adsorption Isotherms
To enrich ellagic acid from PUL extracts using microporous resins effectively, the optimum type of microporous resin was screened first. Because the external factors have a significant effect, the resin adsorption behavior is significantly influenced by many external factors. To evaluate these effects on the resin adsorption capacity, the adsorption kinetics tests and adsorption isotherms of XDA-8D microporous resin for crude ellagic acid were carried out (Figures 5 and 6).
According to Figure 5, the adsorption rate of XDA-8D for crude ellagic acid increased to the biggest within 1 h. Then, it still maintained a fast adsorption rate within 1-5 h. However, it proceeded slowly between 5-10 h and reached equilibrium after 10 h. The results showed that the adsorption capacity was about 1.2 mg/g of dry resin. However, it proceeded slowly between 5-10 h and reached equilibrium after 10 h. The results showed that the adsorption capacity was about 1.2 mg/g of dry resin.

Figure 5. Static adsorption kinetics.
To study the effect of temperature on static adsorption, the adsorption isotherms were investigated at 20 °C, 25 °C, 30 °C and 35 °C. According to the typical adsorption isotherm classified by Brunauer [38] and the preferential equilibrium curves, the adsorption isotherm of XDA-8D belonged to the convex preferential adsorption isotherm (shown in Figure 6). This kind of adsorption isotherm is convex upward along the coordinate direction of adsorption capacity and is called preferential adsorption isotherm. According to Brunauer-Deming-Deming-Teller (BDDT) classification, this means that monolayer molecular adsorption occurs when the pore size of the adsorbent capillary is slightly larger than that of the adsorbent molecule. The experiment data of adsorption isotherms shown in Table 3 were well fitted to a Langmuir model [39]. It showed that the temperature had a certain influence on the adsorption process; 30 °C was the best, with an adsorption capacity of 2.462 mg/mL.

Dynamic Adsorption and Elution
The crude ellagic acid product was adsorbed by XDA-8D macroporous resin and eluted with ethanol aqueous solution in gradients, collecting the 30% ethanol to 80% ethanol elution fraction. After removing the solvent, it was characterized by 1 H NMR, 13 C NMR and MS, shown in Figures S1-S3 (Supplementary Materials), respectively. Meanwhile, the content measured by UPLC was 97% (shown in Figure S4).

Linearity and Limits of Detection and Quantification
The calibration curves were plotted with a series of concentrations of standard solutions. Each analyte curve was made at six levels. Acceptable linear correlation and high sensitivity at these conditions were confirmed by the correlation coefficients (R 2 , 0.9989-0.9999). The limits of detection (LODs) and limits of quantification (LOQs) for standards were estimated at signal-to-noise ratios (S/N) of three and ten, respectively, by injecting a series of dilute solutions with known concentrations. The detailed information regarding calibration curves, linear ranges, LODs and LOQs are displayed in Table S1. 3.6.2. Precision, Repeatability, Stability and Recovery The precisions calculated as relative standard deviation (RSD) were within the range of 0.42-1.28%. The RSD values of three compounds were within the range from 4.67 to To study the effect of temperature on static adsorption, the adsorption isotherms were investigated at 20 • C, 25 • C, 30 • C and 35 • C. According to the typical adsorption isotherm classified by Brunauer [38] and the preferential equilibrium curves, the adsorption isotherm of XDA-8D belonged to the convex preferential adsorption isotherm (shown in Figure 6). This kind of adsorption isotherm is convex upward along the coordinate direction of adsorption capacity and is called preferential adsorption isotherm. According to Brunauer-Deming-Deming-Teller (BDDT) classification, this means that monolayer molecular adsorption occurs when the pore size of the adsorbent capillary is slightly larger than that of the adsorbent molecule. The experiment data of adsorption isotherms shown in Table 3 were well fitted to a Langmuir model [39]. It showed that the temperature had a certain influence on the adsorption process; 30 • C was the best, with an adsorption capacity of 2.462 mg/mL.

Dynamic Adsorption and Elution
The crude ellagic acid product was adsorbed by XDA-8D macroporous resin and eluted with ethanol aqueous solution in gradients, collecting the 30% ethanol to 80% ethanol elution fraction. After removing the solvent, it was characterized by 1 H NMR, 13 C NMR and MS, shown in Figures S1-S3 (Supplementary Materials), respectively. Meanwhile, the content measured by UPLC was 97% (shown in Figure S4).

Linearity and Limits of Detection and Quantification
The calibration curves were plotted with a series of concentrations of standard solutions. Each analyte curve was made at six levels. Acceptable linear correlation and high sensitivity at these conditions were confirmed by the correlation coefficients (R 2 , 0.9989-0.9999). The limits of detection (LODs) and limits of quantification (LOQs) for standards were estimated at signal-to-noise ratios (S/N) of three and ten, respectively, by injecting a series of dilute solutions with known concentrations. The detailed information regarding calibration curves, linear ranges, LODs and LOQs are displayed in Table S1.

Precision, Repeatability, Stability and Recovery
The precisions calculated as relative standard deviation (RSD) were within the range of 0.42-1.28%. The RSD values of three compounds were within the range from 4.67 to 6.15%, which revealed a high repeatability of the method. Stability of the sample solution was tested at room temperature in 12 h. The RSD values of three compounds were all within 5.37%, which demonstrated a good stability within the tested period.
The data for precision, repeatability, stability and recovery were also listed in Table S1. As shown in Table S1, the mean recovery rates of three compounds varied from 93.70 to 107.00% (RSD ≤ 7.10%).

Conclusions
In this study, a combined mechanochemical-macroporous resin adsorption method was established to separate and purify ellagic acid from PUL. The mechanochemistry ball milling coupled with the ultrasonic-assisted solvent extraction method was utilized to increase the extraction yield of ellagitannin. Under the optimized ball-milling conditions, the yield of ellagitannin was increased as compared to the traditional extraction method. The ellagitannin in the PUL extract could be converted into ellagic acid under sulfuric acid hydrolysis. The optimal reaction conditions were as follows: the sulfuric acid amount was 0.552 mol/L, the acidolysis time was 30 min, and the acidolysis temperature was 40 • C. Finally, the crude ellagic acid was separated and purified by XDA-8D macroporous resin to obtain ellagic acid. Under the optimal technological conditions, the yield of ellagic acid was 10.2 mg/g, and the content was over 97%. It is rapid and efficient for the preparation of ellagic acid. Meanwhile, it can also provide a technical basis for the comprehensive utilization of PUL.
Funding: This research received no external funding.

Institutional Review Board Statement: Not applicable.
Informed Consent Statement: Not applicable.