Optimization of a Recombinant Lectin Production in Pichia pastoris Using Crude Glycerol in a Fed-Batch System

: The production of heterologous proteins for medical use is an important area of interest. The optimization of the bioprocesses includes the improvement of time, costs, and unit operations. Our study shows that a lectin fraction from Tepary bean ( Phaseolus acutifolius ) (TBLF) has cytotoxic effects on colon cancer cells and in vivo antitumorigenic activity. However, the low-yield, time-consuming, and expensive process made us focus on the development of a strategy to obtain a recombinant lectin using engineered Pichia pastoris yeast. Pure glycerol is one of the most expensive supplies; therefore, we worked on process optimization using crude glycerol from biodiesel production. Recombinant lectin (rTBL-1) production and puriﬁcation were evaluated for the ﬁrst time by an experimental design where crude glycerol (G65) was used and compared against pure glycerol (G99) in a controlled stirred-tank bioreactor with a fed-batch system. The recombinant lectin was detected and identiﬁed by SDS-PAGE, Western blot, and UHPLC–ESI–QTOF/MS analysis. The results show that the recombinant lectin can be produced from G65 with no signiﬁcant differences with respect to G99: the reaction rates were 2.04 and 1.43 mg L − 1 h − 1 , and the yields were 264.95 and 274.67 mgL − 1 , respectively. The current low cost of crude glycerol and our results show the possibility of producing heterologous proteins using this substrate with high productivity. glycerol do not show signiﬁcant differences [24]. After ﬁve days, glycerol depletion resulted in a plateau of cell growth and protein production with a ﬁnal cell density of 37 g L − 1 and protein level of 58 mg L − 1 .


Introduction
Lectins are mainly glycoproteins that have been considered as potential anticancer molecules due to their specific ability to recognize cancer cell membrane carbohydrates, provoking cell death by apoptosis induction [1]. A semipure lectin fraction from the Tepary bean (TBLF), with at least two glycoproteins (TBL-1 and TBL-2), specifically recognizes colon cancer cells with a differential cytotoxic effect between nonmalignant and malignant cell lines [2]. The effect of TBLF on cancer cells is related with apoptosis induction and cell cycle arrest [3]. TBLF exhibits low toxicity and inhibits early tumorigenesis in rats with chemically induced colon cancer [4,5]. The observed results for TBLF suggest its use as a therapeutic agent against colon cancer; however, the extraction of TBLF is expensive, time consuming, and has low yield. Therefore, a process to obtain a recombinant lectin from the Tepary bean (rTBL-1) was developed using engineered Pichia pastoris yeast [6].
P. pastoris is a methylotrophic yeast that has been used for the high-yield expression of proteins either by secretion to the culture medium or by intracellular localization [7,8]. Table 1. Glycerol purity level.

Fermentation Conditions 2.3.1. Optimization of Glycerol Concentration in Flask Fermentation
To find the optimum glycerol concentration, P. pastoris was grown in 250 mL Erlenmeyer flasks filled with 100 mL of minimum salt medium (MSM), with (20-100 g L −1 ) of G99 at 200 rpm and at 30 • C for 168 h. Once the optimum glycerol concentration was found (40 g L −1 ), cultures were grown using G99, G86, G80, or G65 glycerol in Erlenmeyer flasks at 200 rpm, 30 • C, and initial pH 3 for 168 h.

Optimization of pH in Batch Fermentation
Batch cultures were carried out using a 3-L stirred tank bioreactor, using only 1-L of 40 g L −1 of G99 or G65 as the carbon source medium. The operating conditions were 400 rpm, compressed air continuously sparged into the culture at an aeration rate of 1 vvm, and absolute air pressure of 1 bar. The operating pressure was set by the manipulation of the inlet compressed air and the regulatory valve position in the exit gas line. The short interruption of aeration allowed the determination of the specific oxygen uptake (qO 2 ) rate at exponential phase for G65 and G99 glycerol. All measurements were performed in triplicate at 30 • C.

Operation Parameter Optimization in Fed-Batch Fermentation
To produce the bioreactor inoculum, individual colonies of P. pastoris yeast were selected, inoculated (100 mL of liquid BMG medium), and cultivated in a shaker (30 • C, 200 rpm, 24 h). The inoculum was served into a sterilized bioreactor containing MSM medium, and dissolved oxygen (DO) was maintained at 30% (v/v) of saturation monitored using an electrode (Applikon Biotechnology) through a cascade of air flow and agitation. The batch and fed-batch phase were performed until the glycerol was depleted, as indicated by a sharp rise in DO (DO spike). Samples were taken at intervals 24 and 12-h for batch and feed-batch, respectively; wet cell weight (WCW) and dry cell weight (DCW) were used as cell density determination. The secreted proteins were separated by centrifugation (30 min, 7500× g, 4 • C). The oxygen mass transfer coefficient (kLa) was determined using a dissolved oxygen electrode (AppLiSens Z010032520, Applikon, CA, USA) [14]. Dissolved oxygen concentrations were measured every 5 s by an oxygen electrode attached to a controller in-control (Applikon, CA, USA) and the kLa determination was carried out [15].
The fed-batch fermentation was carried out in the previously described reactor with an absolute air pressure of 1 bar. The optimization parameters were performed at 25-37 • C and pH 3.0-6.0, pH was controlled using an ammonium hydroxide solution. Air-flow rate was of 0.5-1.5 vvm and agitation was of 500-1000 rpm. In this part of the study, a three-stage fermentation protocol was used. The first stage was a G65 (40 g L −1 ) batch fermentation for 24 h. In the second stage, the process was switched to fed-batch using G65-MSM 50% v/v added to the bioreactor with a constant feeding flow rate (F) of 0.06 mL min −1 and dilution rate (D) ranging from 0.02 to 0.007 h −1 according to the equation F = DV 0 e Dt , where F is the feed rate, D is the dilution rate, V 0 is the culture volume when the medium feed started, and t is the time. The medium was pumped into the reactor using a high-pressure pump (MasterFlex). In the third stage, at about 96 h of the fed-batch phase, the process was switched to batch mode using G65 (40 g L −1 ) for 24 h. A DO-Stat was used to control the feeding rate. During the feeding phase of all the fed-batch fermentations, the residual glycerol concentration was found to be below 5 g L −1 . A triplicate analysis was performed using optimal operating conditions with G99.

Purification of rTBL-1
The culture supernatant was separated from the cells by centrifugation (30 min at 7500× g, 4 • C); filtered through GF/D and GF/F glass fiber membranes (Whatman, Sigma-Aldrich, Munich, Germany); and adjusted to 0.02 M sodium phosphate buffer, 0.4 M sodium chloride, pH 7.4, by adding 4× concentrated stock. rTBL-1, which contains a hexa-histidine tail, was purified from the clarified culture supernatant by nickel affinity chromatography using precharged Ni Sepharose 6 fast flow columns (Amersham Biosciences, Little Chalfont, UK) with a flow rate of 2 mL min −1 . After loading, the columns were washed with 0.02 M sodium phosphate buffer, 0.4 M sodium chloride, pH 7.4, and the bound protein was eluted with 0.2 M imidazole in the same buffer. Eluted proteins were checked for purity by SDS-PAGE, dialyzed against deionized water using multiple changes to remove all small molecules, then freeze-dried and stored at −20 • C [6].

rTBL-1 Identification
Aliquots from the soluble and insoluble fractions were assayed for protein content using the Bradford method [16] and using bovine serum albumin as a protein concentration standard. Culture supernatant samples and rTBL-1 fractions were analyzed by SDS-PAGE in 13% (w/v) polyacrylamide gels under denaturing conditions according to standard protocols [17]. All the SDS-PAGE analyses were performed using 25 µL of cleared supernatant, and the gels were stained with Coomassie-based stain (SimplyBlue SafeStain, Invitrogen, MA, USA), and the electrophoresis procedure was carried out according to the manufacturer's instructions. rTBL-1 was estimated using image densitometry software ImageJ [18], where the gels were scanned using an HP ScanJet and protein bands were selected, plotted, and compared using the ImageJ software. The presence of rTBL-1 was confirmed using periodic acid-Schiff [19] staining for the presence of glycoproteins and identified by Western blot. Briefly, transference to nitrocellulose membranes (Bio Rad) was conducted at 4 • C and 15 V for 20 min in a Trans-Blot ® SD Semi-Dry Electrophoretic Transfer Cell (Bio Rad, USA). The membrane was blocked with blocking buffer TTBS (tween-20 0.05% (w/v) and 5% skim milk (w/v)) overnight at 4 • C under shaking (420 rpm). The membrane was incubated for 60 min at room temperature under constant agitation with a polyclonal anti-rTBL-1 antibody [20] 1:30,000 in 1× TTBS with 2% (w/v) skim milk, followed by several washes with 1× TTBS. The membrane was blocked again with blocking buffer for 1 h at room temperature under constant agitation and incubated with the secondary antibody (antirabbit IgG, H+L) conjugated with horseradish peroxidase (Jackson Immune Research, Baltimore, MD, USA) 1:15,000 for 1 h at room temperature. The membrane was rewashed with 1× TTBS and immunodetection was achieved using the Amersham TM ECL TM prime Western blotting detection reagent (GE Healthcare, Little Chalfont, Bucks, UK).

Statistical Analysis
Comparisons between treatments were analyzed by one-way ANOVA for glycerol concentration and pH optimization (Tukey, p ≤ 0.05) and for the rTBL-1 cytotoxic effect (Dunnett, p ≤ 0.05). To study the effect of four operational variables (aeration, agitation rates, temperature, and pH) ( Table 2) on three independent factors (oxygen mass transfer coefficient (kLa), dry cell weight, and rTBL-1), a robust-model process-optimization experimental design was used [22]. Experiments of the three independent factors, each one at four levels with two center points and eight replicates, were performed, resulting 26 experiments for G65. For response surface methodology (RSM) experiments, the "Fusion Pro" experiment design software (Version 6.7.0, CA, USA) was used for regression and graphical analysis of the experimental results. Linear and quadratic models were obtained.

Effect of Glycerol Concentration on rTBL-1 Production in Batch Cultures
A critical parameter that needs to be controlled with precision in bioprocesses is glycerol concentration. Growth kinetics and quantitation of rTBL-1 were obtained for each glycerol concentration (data shown only for 40 g L −1 ). To find the optimal glycerol concentration, 20-100 g L −1 were tested using a batch system and rTBL-1 production was measured after 168 h. Results are shown in Figure 1A. rTBL-1 production was higher at a concentration of 40 g L −1 with G99, reaching 53.5 mg L −1 . Biomass accumulation was similar at glycerol concentrations of 40 and 60 g L −1 , starting from >40 g WCW L −1 at induction to >38 g WCW L −1 . At a glycerol concentration of 100 g L −1 , the lowest amount of rTBL-1 was produced (20.27 mg L −1 ). The cells grew very slowly, reaching >20.39 g WCW L −1 . The growth-limiting level of glycerol for P. pastoris cells must be related with the observed slow growth and low protein expression. tained.

Effect of Glycerol Concentration on rTBL-1 Production in Batch Cultures
A critical parameter that needs to be controlled with precision in bioprocesses is gly erol concentration. Growth kinetics and quantitation of rTBL-1 were obtained for ea glycerol concentration (data shown only for 40 g L −1 ). To find the optimal glycerol conce tration, 20-100 g L −1 were tested using a batch system and rTBL-1 production was mea ured after 168 h. Results are shown in Figure 1A. rTBL-1 production was higher at a co centration of 40 g L −1 with G99, reaching 53.5 mg L −1 . Biomass accumulation was simil at glycerol concentrations of 40 and 60 g L −1 , starting from >40 g WCW L −1 at induction >38 g WCW L −1 . At a glycerol concentration of 100 g L −1 , the lowest amount of rTBL-1 w produced (20.27 mg L −1 ). The cells grew very slowly, reaching >20.39 g WCW L −1 . Th growth-limiting level of glycerol for P. pastoris cells must be related with the observe slow growth and low protein expression.  Figure 1B shows the production of wet cell weight and the quantification of rTBL with an initial concentration of 40 g L −1 of G99. The maximum concentration of recomb nant lectin was reached by starting the stationary growth phase of the yeast P. pastoris, f which the process was stopped at 168 h, and the extraction and purification of the lect was prepared.  Figure 1B shows the production of wet cell weight and the quantification of rTBL-1 with an initial concentration of 40 g L −1 of G99. The maximum concentration of recombinant lectin was reached by starting the stationary growth phase of the yeast P. pastoris, for which the process was stopped at 168 h, and the extraction and purification of the lectin was prepared.

Comparison of the Four Purity Levels of Glycerol as Substrate in Batch Cultures
It has been reported that the level of expression of heterologous proteins by P. pastoris with the pGAP vector is dependent on the carbon source and the foreign protein [23]. In this study, four levels of glycerol purity were tested in parallel experiments for P. pastoris cultures: G99, G86, G80, and G65. The results are displayed in Figure 2. The data show the average four identical batches. In similar flask experiments, crude glycerol and pure glycerol do not show significant differences [24]. After five days, glycerol depletion resulted in a plateau of cell growth and protein production with a final cell density of 37 g L −1 and protein level of 58 mg L −1 .
It has been reported that the level of expression of heterologous proteins by P. pastoris with the pGAP vector is dependent on the carbon source and the foreign protein [23]. In this study, four levels of glycerol purity were tested in parallel experiments for P. pastoris cultures: G99, G86, G80, and G65. The results are displayed in Figure 2. The data show the average four identical batches. In similar flask experiments, crude glycerol and pure glycerol do not show significant differences [24]. After five days, glycerol depletion resulted in a plateau of cell growth and protein production with a final cell density of 37 g L−1 and protein level of 58 mg L−1. In a recent study, crude glycerol impurities such as methyl ester, grease, glycerol, methanol, and metal ions Na + , Ca 2+ , and Fe 3+ were determined on lipase production in P. pastoris yeast. Impurities sped up the stationary phase and, under the same fermentation conditions, cell growth and enzyme activity increased using crude glycerol instead of pure glycerol. These results suggest that impurities can accelerate P. pastoris growth [25]. In our study, no inhibition was observed by the impurities possibly present in crude and semicrude glycerol.

Effect of pH on rTBL-1 Production in Batch Cultures
Batch experiments were conducted in a 3-L bioreactor using only G99 to study the effect of pH in the bioprocess (Figure 3). The initial carbon source concentration in the MSM medium was 40 g L −1 , pH of the broth was controlled with ammonium hydroxide, and the dissolved oxygen level was maintained above 30% (v/v). Compared to the shake flasks, an increase in biomass and protein production was observed, which can be related to the aerobic environment. The batch system showed better results than baffled flasks with maximum specific growth rate values of 41% more, biomass yield of 34% more, and protein product yield of 44% or more. No cell growth inhibitory effects caused by fermentative byproducts were detected when glycerol was used as the substrate in P. pastoris [26]. In a recent study, crude glycerol impurities such as methyl ester, grease, glycerol, methanol, and metal ions Na + , Ca 2+ , and Fe 3+ were determined on lipase production in P. pastoris yeast. Impurities sped up the stationary phase and, under the same fermentation conditions, cell growth and enzyme activity increased using crude glycerol instead of pure glycerol. These results suggest that impurities can accelerate P. pastoris growth [25]. In our study, no inhibition was observed by the impurities possibly present in crude and semicrude glycerol.

Effect of pH on rTBL-1 Production in Batch Cultures
Batch experiments were conducted in a 3-L bioreactor using only G99 to study the effect of pH in the bioprocess (Figure 3). The initial carbon source concentration in the MSM medium was 40 g L −1 , pH of the broth was controlled with ammonium hydroxide, and the dissolved oxygen level was maintained above 30% (v/v). Compared to the shake flasks, an increase in biomass and protein production was observed, which can be related to the aerobic environment. The batch system showed better results than baffled flasks with maximum specific growth rate values of 41% more, biomass yield of 34% more, and protein product yield of 44% or more. No cell growth inhibitory effects caused by fermentative byproducts were detected when glycerol was used as the substrate in P. pastoris [26].
It is known that P. pastoris is capable of growth over a broad pH range; therefore, rTBL-1 production was evaluated from pH 3 to 6. It has been reported that this range of pH has little or no effect on the cell growth [27]; nevertheless, it can affect recombinant protein secretion since the activity of certain enzymes such as proteases in the fermentation medium is affected by pH [28]. A strategy used for optimization studies consists of changing the medium pH to 5 because it is optimum for cell growth [27,29]. However, the optimum pH for shake flask culture may not necessarily be the same for fermentation. Dehnavi et al. [30] reported that the optimum pH for β-xylosidase production in shake flask culture was 4.8, but during fermentation, the optimum was 6. pH was the most significant factor affecting the rTBL-1 production with a minimum point between 3, 4, and 6 ( Figure 3A).  It is known that P. pastoris is capable of growth over a broad pH range; therefore, rTBL-1 production was evaluated from pH 3 to 6. It has been reported that this range of pH has little or no effect on the cell growth [27]; nevertheless, it can affect recombinant protein secretion since the activity of certain enzymes such as proteases in the fermentation medium is affected by pH [28]. A strategy used for optimization studies consists of changing the medium pH to 5 because it is optimum for cell growth [27,29]. However, the optimum pH for shake flask culture may not necessarily be the same for fermentation. Dehnavi et al. [30] reported that the optimum pH for β-xylosidase production in shake flask culture was 4.8, but during fermentation, the optimum was 6. pH was the most significant factor affecting the rTBL-1 production with a minimum point between 3, 4, and 6 ( Figure 3A).
The low response may be due to proteolytic degradation in this pH range due to the presence of host proteases in Pichia fermentation [31]. P. pastoris has a growth range of pH from 3 to 7, therefore, it is possible that protein production would decrease as the pH increases. Based on our results, optimum rTBL-1 production should occur between 4 and 5 to avoid proteolytic degradation ( Figure 3B).

Operation Parameter Optimization Using G65 by Fed-Batch Fermentation
Most fermentation processes using Pichia yeast are carried out at an optimum temperature of 30 °C [25], although the effect of temperature on recombinant protein production in P. pastoris has not been reported. In our experimental design, the temperature ranged from 25 to 37 °C. The model suggests that temperatures above 30 °C are not adequate for rTBL-1 production. It was observed that temperatures above 32 °C could decrease protein expression and provoke cell death [32] due to cell lysis and high protease activity in cultures. Our results suggest that temperatures between 25 and 30 °C are optimum for rTBL-1 production.
The effects of glycerol on rTBL-1 expression in fed-batch fermentations using G65 are shown in Figure 4A. The fermentation profile showed that production of recombinant protein was associated to biomass formation. Glycerol from G65 was entirely consumed in about 96 h, less than in shake flasks. In addition, the volumetric mass oxygen transfer coefficient (kLa) has been reported to have an essential role in other yeasts growing on glycerol [33]. The low response may be due to proteolytic degradation in this pH range due to the presence of host proteases in Pichia fermentation [31]. P. pastoris has a growth range of pH from 3 to 7, therefore, it is possible that protein production would decrease as the pH increases. Based on our results, optimum rTBL-1 production should occur between 4 and 5 to avoid proteolytic degradation ( Figure 3B).

Operation Parameter Optimization Using G65 by Fed-Batch Fermentation
Most fermentation processes using Pichia yeast are carried out at an optimum temperature of 30 • C [25], although the effect of temperature on recombinant protein production in P. pastoris has not been reported. In our experimental design, the temperature ranged from 25 to 37 • C. The model suggests that temperatures above 30 • C are not adequate for rTBL-1 production. It was observed that temperatures above 32 • C could decrease protein expression and provoke cell death [32] due to cell lysis and high protease activity in cultures. Our results suggest that temperatures between 25 and 30 • C are optimum for rTBL-1 production.
The effects of glycerol on rTBL-1 expression in fed-batch fermentations using G65 are shown in Figure 4A. The fermentation profile showed that production of recombinant protein was associated to biomass formation. Glycerol from G65 was entirely consumed in about 96 h, less than in shake flasks. In addition, the volumetric mass oxygen transfer coefficient (kLa) has been reported to have an essential role in other yeasts growing on glycerol [33].
The kLa increased accordingly with superficial gas velocity and decreased with cellular density. The increase in initial kLa from 65 h −1 to 115 h −1 led to a 4.6-fold increase in rTBL-1 s final concentration ( Figure 4B). On the other hand, experiments were also performed with controlled dissolved oxygen (DO). Setting an optimal kLa instead of controlled DO suggests that kLa is a good parameter for the rTBL-1 production using crude glycerol in P. pastoris fermentations and it is necessary considering it in bioprocess scale-ups. Of the two models for rTBL-1 (Fisher's test), the one that presented the best fit was the polynomial quadratic model. Statistical data are shown in Table 3.  The kLa increased accordingly with superficial gas velocity and decreased with cellular density. The increase in initial kLa from 65 h −1 to 115 h −1 led to a 4.6-fold increase in rTBL-1′s final concentration ( Figure 4B). On the other hand, experiments were also performed with controlled dissolved oxygen (DO). Setting an optimal kLa instead of controlled DO suggests that kLa is a good parameter for the rTBL-1 production using crude glycerol in P. pastoris fermentations and it is necessary considering it in bioprocess scaleups. A second-order polynomial model provided the best fit to the experimental data obtained for rTBL-1:  According to the results obtained by the experimental design, it was shown that the parameter with the greatest significance for the models was agitation, followed by pH and temperature. The most significant parameters expressed by the Pareto diagram for rTBL-1 production were agitation and temperature. On the other hand, for biomass production, the significant parameter continued to be agitation, as well as temperature and pH for the oxygen transfer coefficient. Figure 4C shows that the metabolism of glycerol in P. pastoris is aerobic, with 0.5-1.6 vvm flux, even at high glycerol concentrations using fed-batch systems, considering that glycerol is a low fermentative carbon source. The experimental conditions used in this work show that an aeration rate rise of up to 1 vvm is adequate for the fed-batch cultivation of P. pastoris.

Comparison of Process Parameters Using G99 and G65 by Fed-Batch Fermentation
Due to the importance of using the byproducts of biodiesel as a carbon source for rTBL-1 production, and the fact that there were no differences between the four carbon sources used, only G99 and G65 were selected for the optimization of fermentation parameters. P. pastoris exhibited high demand on dissolved oxygen, the use of bioreactors allows a higher transfer rate with faster consumption of the carbon source. Comparative results between G99 and G65 glycerol production parameters are shown in Table 4, where the potential application of glycerol derived from biodiesel production in P. pastoris fermentations shows good potential to generate value-added products. Table 4. Substrate effect on rTBL-1 production using P. pastoris in a fed-batch system at 1000 rpm, pH 4.5, and 1 vvm using G99 or G65. In a previous study, Martinez-Alarcón et al. [6] worked with the same strain using pure glycerol under the following operating conditions: 30 • C, pH 5, and a fed-batch system. The authors obtained 316 mg recombinant lectin L −1 ; here, we obtained 275 and 265 mg recombinant lectin L −1 through a production optimization with G99 and G65, respectively. Differences in yield between pure glycerol systems may be due to the standardization between different laboratory conditions and the equipment used since Martinez-Alarcon used an Applikon bioreactor of 7 L. In our study, we used a 3-L bioreactor. However, we show that no differences were obtained between G99 and G65 substrates and that it is important to standardize the production for a larger equipment.
Several studies have shown the utilization of glycerol for the production of heterologous proteins. Different glycerol preparations were assayed for P. pastoris growth and recombinant erythropoietin production [13]. A 1.5-fold improvement in cell concentration using glycerol from canola oil when compared to pure glycerol was observed. However, glycerol derived from soybean was not suitable due to simple precipitation. The recombinant yeast had the heterologous gene under the inducible pAOX1 promoter control, which supposes two steps: to obtain high cell density and to induce heterologous gene production by methanol addition. In this study, a single step was carried out for both biomass and heterologous protein production. The constitutive production of a phytase encoding gene cloned under the control of the constitutive pGAP promoter using glucose and glycerol as substrates has been reported [26]. In these conditions, P. pastoris showed a 30% increase in cell growth and a 10% increase in recombinant protein production; however, the authors reported that it was a necessary glycerol pretreatment. Therefore, as far as we know, our study is the first to report the experimental design and utilization of crude glycerol without any pretreatment for the efficient production of a recombinant protein; in this case, the rTBL-1.
Recombinant protein production in fermenter cultures of P. pastoris is generally performed using a two-stage process [34]. In the first stage, the culture grows in a batch phase with a repressing carbon source-in this case, glycerol-for biomass production. When the initial carbon source has been fully consumed, a growth-limiting amount of the repressing carbon source is fed that allows a phase change in which biomass production increases. In our study, we found that this resulted in a biomass accumulation of >60 g WCW L −1 prior to feed.
For P. pastoris bioprocesses, pH is a critical parameter for cell growth, productivity, and product quality. To optimize the process, an experimental design was tested for pH and temperature, maintaining aeration and agitation rates set points. The initial biomass at the start of induction was around 5 g L −1 WCW. During the growth phase, glycerol was fed exponentially for 48 h with a feed rate ranging from 0.02 to 0.007 h −1 . Harvest was performed 72 h post-feed, and the products were purified and analyzed through protein chromatography. The results show that the yield increased as the aeration and agitation rate increased. On the other hand, increases in pH and temperature resulted in decreased yield. To achieve a high yield, the preferred set points were temperatures between 25 and 30 • C, high agitation and aeration rate, and low pH. According to the DoE results, the optimal pH and temperature for both productivity and product quality would be pH 4.5 and 25 • C. When experiments were performed under these conditions, no significant differences for yield between G99 and G65 were observed ( Table 5). The temperature and DO were kept constant, with the pH set at 4.5. Ye et al. [35] demonstrated the production of an antibody by P. pastoris through an optimization design, showing that, at 26 • C and pH 6.3, they reached their maximum yield. Table 5. Kinetic parameters of rTBL-1 production using P. pastoris in a fed-batch system at 1000 rpm, pH 4.5, and 1 vvm using G99 or G65 glycerol.
Our results suggest that the bioprocess was not inhibited by free fatty acids from crude glycerol. The fastest glycerol consumption rate was observed for G99 (1.82 mg L −1 h −1 ), contrary to a study where pure glycerol had the slowest carbon source utilization rate [36]. Nevertheless, P. pastoris growing on G65 showed no significant differences when compared to G99 fermentation with a glycerol utilization rate of 1.65 mg L −1 h −1 .
Some reports have mentioned that the oil type and catalyst used for biodiesel production may result in crude glycerol with a diversity of impurities such as fatty acids, methanol, salts, and heavy metals [37,38]. High unsaturated fatty acids in crude glycerol may exhibit an inhibitory effect on C. pasteurianum [38], but some reports show that yeasts can tolerate the presence of impurities in crude glycerol more effectively than bacteria. In particular, ethanol production from Pachysolen tannophilus was not inhibited by the three experimented crude glycerol batches derived from rapeseed oil [39]. It has been reported that yeasts isolated from soil [40] and Candida sp. [41] grew efficiently in crude glycerol for the production of chemicals and lipids, respectively. Further, P. pastoris has been utilized for recombinant proteins production using crude glycerol [42,43]. Figure 5 shows the rTBL-1 electrophoresis detection and mass spectra after the optimization process using G65 as substrate. SDS-PAGE showed the presence of a single band of~30 that was stained by Schiff-PAS and identified by Western blot ( Figure 5A). The rTBL-1 mass spectrometry (UHPLC-ESI-QTOF/MS) at 3.095 min is shown with a major peak at 947.6 m/z ( Figure 5B). The deconvolution spectrum of this peak showed a single peak with a molecular mass of 29,343.0020 Da ( Figure 5C). particular, ethanol production from Pachysolen tannophilus was not inhibited by the three experimented crude glycerol batches derived from rapeseed oil [39]. It has been reported that yeasts isolated from soil [40] and Candida sp. [41] grew efficiently in crude glycerol for the production of chemicals and lipids, respectively. Further, P. pastoris has been utilized for recombinant proteins production using crude glycerol [42,43]. Figure 5 shows the rTBL-1 electrophoresis detection and mass spectra after the optimization process using G65 as substrate. SDS-PAGE showed the presence of a single band of ~30 that was stained by Schiff-PAS and identified by Western blot ( Figure 5A). The rTBL-1 mass spectrometry (UHPLC-ESI-QTOF/MS) at 3.095 min is shown with a major peak at 947.6 m/z ( Figure 5B). The deconvolution spectrum of this peak showed a single peak with a molecular mass of 29,343.0020 Da ( Figure 5C).

Comparison Between rTBL-1 and the Native Lectin and Cytotoxic Effect
The coverage percentage of identity between the mature sequences of rTBL-1 and the Tepary bean native lectin [21] was 96.24%, with only five amino acid mismatches ( Figure 6). In position 116, R changed to K; in position 157-158, GQ changed to VN; in position 205, R changed to S; and in position 215, T changed to S. Most of the mismatches are located between loops that serve as blade connectors. None of them are located in the proximity of the glycosylation site (red triangle), nor do they correspond to any of the amino acids involved in the coordination bonding with the ions (yellow stars). Furthermore, none of them correspond to the residues predicted to be involved in carbohydrate binding (green circles). It is not expected that these slight variations have an influence on the folding or activity of the protein.
The coverage percentage of identity between the mature sequences of rTBL-1 and the Tepary bean native lectin [21] was 96.24%, with only five amino acid mismatches ( Figure  6). In position 116, R changed to K; in position 157-158, GQ changed to VN; in position 205, R changed to S; and in position 215, T changed to S. Most of the mismatches are lo cated between loops that serve as blade connectors. None of them are located in the prox imity of the glycosylation site (red triangle), nor do they correspond to any of the amino acids involved in the coordination bonding with the ions (yellow stars). Furthermore none of them correspond to the residues predicted to be involved in carbohydrate binding (green circles). It is not expected that these slight variations have an influence on the fold ing or activity of the protein. rTBL-1 quantitation with respect to the native lectin from TBLF was carried out by protein band densitometry after 13% (w/v) polyacrylamide SDS-PAGE ( Figure 7A). The difference in molecular weight between the native lectin and the rTBL-1 is due to the hexa histidine tail. It was observed that the native lectin corresponded to approximately 30% of all the proteins present in the TBLF lyophilized product, while the rTBL-1 corresponded to 80% of the total protein in the lyophilized product, and it was equivalent to 63% of the total TBLF protein. The protein concentration of rTBL-1 was adjusted to assess the cyto toxic effect of rTBL-1 with respect to the TBLF LC50 (402 μg/mL, 55 μg native lectin/mL [3]. rTBL-1 quantitation with respect to the native lectin from TBLF was carried out by protein band densitometry after 13% (w/v) polyacrylamide SDS-PAGE ( Figure 7A). The difference in molecular weight between the native lectin and the rTBL-1 is due to the hexahistidine tail. It was observed that the native lectin corresponded to approximately 30% of all the proteins present in the TBLF lyophilized product, while the rTBL-1 corresponded to 80% of the total protein in the lyophilized product, and it was equivalent to 63% of the total TBLF protein. The protein concentration of rTBL-1 was adjusted to assess the cytotoxic effect of rTBL-1 with respect to the TBLF LC 50 (402 µg/mL, 55 µg native lectin/mL) [3].
The dose-response curve resulted in an LC 50 of 56 µg of rTBL-1 protein/mL ( Figure 7B). These results show that the rTBL-1 maintains the biological effect observed for the TBLF. The cytotoxic effect is observed to be a function of the rTBL-1 concentration, and the LC 50 is similar to that observed for TBLF (56 and 55 µg of lectin protein, respectively) [3]. Therefore, experiments for the study of the mechanisms of action and in vivo toxicology and anticancer effects will be performed using the rTBL-1 to advance the development of a new molecule for treating colon cancer. ses 2021, 9,   The dose-response curve resulted in an LC50 of 56 μg of rTBL-1 protein/mL ( Figure  7B). These results show that the rTBL-1 maintains the biological effect observed for the TBLF. The cytotoxic effect is observed to be a function of the rTBL-1 concentration, and the LC50 is similar to that observed for TBLF (56 and 55 μg of lectin protein, respectively) [3]. Therefore, experiments for the study of the mechanisms of action and in vivo toxicology and anticancer effects will be performed using the rTBL-1 to advance the development of a new molecule for treating colon cancer.

Conclusions
In this study, we optimized the rTBL-1 production using crude glycerol by adjusting temperature induction, agitation, aeration, and pH in P. pastoris. This is the first report, to our knowledge, concerning the production of rTBL-1 by this strategy. The production of rTBL-1 using a fed-batch fermentation process was achieved using an experimental design with a maximum yield of 265 ± 13 mgL −1 in the fed-batch fermentation, as predicted by the model. Yeast grown in crude glycerol did not show statistically significant differences with respect to yeast grown in pure glycerol in a batch and fed-batch system. Aeration rate had positive growth effects of this yeast with crude glycerol. The significant increase in productivity using moderate aeration and the availability and low cost of crude glycerol from biodiesel production give an opportunity for designing low-cost biotechnological processes using glycerol as a substrate. The resulting recombinant lectin was identified by SDS-PAGE, Western blot, and MS analysis. The genetic sequence showed high homology with respect to the native lectin, and the recombinant protein showed similar

Conclusions
In this study, we optimized the rTBL-1 production using crude glycerol by adjusting temperature induction, agitation, aeration, and pH in P. pastoris. This is the first report, to our knowledge, concerning the production of rTBL-1 by this strategy. The production of rTBL-1 using a fed-batch fermentation process was achieved using an experimental design with a maximum yield of 265 ± 13 mgL −1 in the fed-batch fermentation, as predicted by the model. Yeast grown in crude glycerol did not show statistically significant differences with respect to yeast grown in pure glycerol in a batch and fed-batch system. Aeration rate had positive growth effects of this yeast with crude glycerol. The significant increase in productivity using moderate aeration and the availability and low cost of crude glycerol from biodiesel production give an opportunity for designing low-cost biotechnological processes using glycerol as a substrate. The resulting recombinant lectin was identified by SDS-PAGE, Western blot, and MS analysis. The genetic sequence showed high homology with respect to the native lectin, and the recombinant protein showed similar cytotoxic effects with respect to the previously determined Tepary bean lectin fraction. Our system using crude glycerol offers efficient production of a recombinant lectin, improving costs and process times, that will allow rTBL-1 production for the study of its anticancer potential in in vitro and in vivo assays.