Puriﬁcation of Textile Efﬂuents Containing C.I. Acid Violet 1: Adsorptive Removal versus Hydrogen Peroxide and Peracetic Acid Based Advanced Oxidation

: Textile efﬂuent containing azo dyes such as C.I. Acid Violet 1 (AV1) can be degraded to toxic aromatic amines in the environment. Thus, there is a legitimate need to treat such efﬂuents before they are discharged to surface waters. Two methods were proposed to remove AV1 from aqueous solutions: adsorption and advanced oxidation processes (AOPs). The sorption capacity of the strongly basic anion exchanger Purolite A520E of the polystyrene matrix determined from the Langmuir isotherm model was found to be 835 mg/g, while that of Lewatit S5428 of the polyacrylamide matrix Freundlich model seems to be more appropriate for describing the experimental data. The pseudo-second-order kinetic model and external diffusion are the rate limiting steps of adsorption. The removal efﬁciency of AV1 by the anion exchangers was higher than 99% after 40 min of phase contact time. AOPs involved the usage of hydrogen peroxide and peracetic acid (PAA) as oxidizing agents, while Fe 2+ and simulated sunlight were used as oxidizing activators. AV1 oxidation followed the pseudo-ﬁrst-order kinetics, and the systems with the highest values of the rate constants turned out to be those in which Fe 2+ was present. The efﬁciency of oxidation measured by the degree of decolorization in the systems with Fe 2+ was higher than 99% after 10–60 min. AV1 mineralization was slower, but after 120 min of oxidation it was higher than 98% in the H 2 O 2 /Fe 2+ , PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems.


Introduction
Synthetic dyes are widely used in various industries, including the production of textiles, food, plastic, cosmetics and paper. According to current data, more than 100,000 dyes are known, and their annual production has reached 700,000 tons [1]. The consumption of dyes in the textile industry around the world exceeds 10,000 tons per year, of which about 1% is discharged into the aquatic environment [2].
Dyes are characterized by intense color, even when their concentrations are small [3][4][5]. They can affect the photosynthetic activity of aquatic plants due to the reduced penetration of light. Dyes also show toxicity for some aquatic organisms, and their carcinogenic, mutagenic or teratogenic effects have been proved in relation to some microorganisms and fish species [6,7]. It was estimated that LD50 (lethal dose, 50%) values greater than 2 × 10 3 mg/kg were exhibited by 90% of the 4000 dyes tested. The highest toxicity was found for basic and diazo direct dyes [8]. Dyes may adversely affect human health, causing dysfunction of the kidneys, reproductive system, liver, brain and central nervous system [9]. Particularly dangerous is the introduction of azo dyes into the environment, which are broken down to toxic amines [8]. A number of chemical (including photochemical and been used as oxidants in AOPs processes [41][42][43]. Oxidation in these processes takes place through the action of radicals formed in the solution, which besides˙OH are SO 4˙− or CH 3 COO˙ [41]. Oxidation processes under the influence of PAA, which, as a non-toxic and environmentally friendly compound, is widely used in practice to disinfect surfaces intended for contact with food, are particularly little studied [42]. Similar factors are used to activate PAA as in the case of H 2 O 2 . The most commonly used are Fe 2+ ions (pseudo-Fenton system) and UV light [41]. Due to the method of synthesis, commercial preparations of this compound exist in the form of an equilibrium mixture of PAA and H 2 O 2 .
The main advantage of AOPs is that the removed contaminants are degraded into simpler compounds. In most cases, organic compounds are completely mineralized and converted to carbon dioxide, water and inorganic salts [44].
The aim of this study was to compare the efficiency of AV1 (C.I. Acid Violet 1) dye removal by the adsorption technique using anion exchange resins and by an advanced oxidation process using hydrogen peroxide and peracetic acid. Parameters influencing the adsorption of AV1 on the anion exchangers such as initial dye concentration, phase contact time and presence of additives (Na 2 SO 4 , CH 3 COOH, anionic and non-ionic surfactants) were investigated by determining kinetic and equilibrium parameters. Regeneration efficiency was also evaluated. The course of AV1 oxidation in seven different oxidation systems based on the use of hydrogen peroxide (H 2 O 2 alone, H 2 O 2 /solar light, H 2 O 2 /Fe 2+ ) and peracetic acid (PAA alone, PAA/solar light, PAA/Fe 2+ , PAA/Fe 2+ /solar light) was determined. The influence of the oxidant concentration on the course of the processes was investigated and kinetic studies were performed. The efficiency of the oxidation processes was determined both on the basis of changes in absorbance in the maximum of absorption (decolorization), as well as on the basis of changes in chemical oxygen demand (COD), which allowed for the evaluation of mineralization.
(PMS) and persulfates (PS)-as well as organic peracids, mainly peracetic acid have been used as oxidants in AOPs processes [41][42][43]. Oxidation in these proces place through the action of radicals formed in the solution, which besides ˙OH a or CH3COO˙ [41]. Oxidation processes under the influence of PAA, which, as a n and environmentally friendly compound, is widely used in practice to disinfect intended for contact with food, are particularly little studied [42]. Similar factors to activate PAA as in the case of H2O2. The most commonly used are Fe 2+ ions ( Fenton system) and UV light [41]. Due to the method of synthesis, commercial tions of this compound exist in the form of an equilibrium mixture of PAA and H The main advantage of AOPs is that the removed contaminants are degra simpler compounds. In most cases, organic compounds are completely minerali converted to carbon dioxide, water and inorganic salts [44].
The aim of this study was to compare the efficiency of AV1 (C.I. Acid Viole removal by the adsorption technique using anion exchange resins and by an a oxidation process using hydrogen peroxide and peracetic acid. Parameters influen adsorption of AV1 on the anion exchangers such as initial dye concentration, ph tact time and presence of additives (Na2SO4, CH3COOH, anionic and non-ioni tants) were investigated by determining kinetic and equilibrium parameters. R tion efficiency was also evaluated. The course of AV1 oxidation in seven differen tion systems based on the use of hydrogen peroxide (H2O2 alone, H2O2/sol H2O2/Fe 2+ ) and peracetic acid (PAA alone, PAA/solar light, PAA/Fe 2+ , PAA/Fe 2+ /so was determined. The influence of the oxidant concentration on the course of the p was investigated and kinetic studies were performed. The efficiency of the oxida cesses was determined both on the basis of changes in absorbance in the maxi absorption (decolorization), as well as on the basis of changes in chemical oxygen (COD), which allowed for the evaluation of mineralization.

Materials
C.I. Acid Violet 1 (C.I. 17025) is a single azo-type dye ( Figure 1). It was obtain Boruta-Kolor S.A. (Zgierz, Poland) and was used without additional purification Two resins of the anion exchange type were applied in the adsorption test. B ins are the strongly basic anion exchangers of a macroporous structure but with a matrix composition. The anion exchangers' properties are presented in Table 1. Two resins of the anion exchange type were applied in the adsorption test. Both resins are the strongly basic anion exchangers of a macroporous structure but with a different matrix composition. The anion exchangers' properties are presented in Table 1.

Adsorption and Desorption Tests
The adsorption studies were carried out at room temperature by the batch technique. This involves shaking the known amount of the anion exchanger (0.5 g) with an aqueous solution of predetermined volume (50 mL) and initial concentration during a defined time (from 1 to 240 min (kinetic tests) or 24 h (isothem studies)) using an Erlenmeyer flask. After shaking on a mechanical shaker (Elpin Plus, Lubawa, Poland) at an amplitude of 7 and 180 rpm, the resins were separated by filtration, and the concentration of the dye was measured using a UV-VIS spectrophotometer Cary 60 (Agilent Technologies, Santa Clara, CA, USA) by measuring absorbance at λ max = 552 nm.
The initial AV1 concentrations used to evaluate the isotherm and kinetic data ranged from 1000 to 10,000 mg/L and from 100 to 500 mg/L, respectively. The initial pH of the solutions was~4.85. Effects of auxiliaries such as electrolytes, acid and surfactants on the AV1 sorption by the anion exchangers was investigated in the systems with the following composition: 500 mg/L AV1 + 5-25 g/L Na 2 SO 4 , 500 mg/L AV1 + 0.25-1 g/L CH 3 COOH, 500 mg/L AV1 + 0.1-0.25 g/L SDS and 500 mg/L AV1 + 0.1-0.25 g/L TX100 during a sorption time t of 15 min. The amounts of AV1 adsorbed by the S5428 and A520E anion exchangers at equilibrium (q e ) and at time t (q t ) as well as removal efficiency (RE) were calculated from the equations where C 0 , C e and C t (mg/L) show AV1 concentrations in the solution before adsorption, at equilibrium and after sorption time t, respectively; V (L) is the volume of AV1 solution; and m (g) is the mass of S5428 and A520E. Three isotherm models were applied in order to determine the adsorption equilibrium parameters for AV1 retention on the strongly basic anion exchange resins: the Langmuir, the Freundlich and the Temkin [47][48][49][50][51]. Kinetic data were modeled using the most popular Processes 2021, 9,1911 5 of 20 kinetic equation; i.e., the pseudo-first order by Lagergren, the pseudo-second order by Ho and the intraparticle diffusion by Weber and Morris [47][48][49][50][51]. Table 2 summarizes the above-mentioned equilibrium and kinetic models. Table 2. Isotherm and kinetic models used for the description of adsorption equilibrium systems.

Isotherm Equation No. Linear Forms Plot
log q e = log k F + 1 n log C e log q e vs. log C e where q e (mg/g)-amount of AV1 adsorbed at equilibrium per unit mass of A520E and S5428, q t (mg/g)-amount of AV1 adsorbed at time t per unit mass of A520E and S5428, C e (mg/L)-equilibrium concentration of AV1 in solution, Q 0 (mg/g)-monolayer adsorption capacity, k L (L/mg)-the Langmuir constant (related to the free energy of adsorption), K F (mg 1−1/n L 1/n /g) and n-the Freundlich constants related to adsorption capability and adsorption intensity, respectively, R (8.314 J/mol K)-gas constant, T (K)-temperature, A (L/g) and b T (J/mol)-the Temkin constants, k 1 (1/min) and k 2 (g/mg min)-rate constants of sorption determined from PFO and PSO equations, respectively, k i (mg/g min 0.5 )-intraparticle diffusion rate constant.
Desorption studies were performed using samples of anion exchangers (0.5 g) uploaded with AV1, (q e = 50 mg/g). The resin beads were shaken for 3 h with 50 mL of regenerants such as 1 M NaCl, 1 M NaOH, 1 M HCl, 1 M NaCl + 50% v/v CH 3 OH, 1 M NaOH + 50% v/v CH 3 OH and 1 M HCl + 50% v/v CH 3 OH. Three cycles of sorption and desorption were performed. The amount of AV1 desorbed form the anion exchanger phase was evaluated using UV-vis measurements and calculated by mass balance as a desorption percentage using the following formula: where m des is the mass of AV1 desorbed (mg) and m ads is the mass of AV1 adsorbed (mg). The adsorption and desorption experiments were carried out in triplicate, and the mean value is presented. The standard deviation did not exceed 5%.

Advanced Oxidation Processes
Peracetic acid solution was prepared according to the following procedure: 10 mL of 99.5% acetic acid and 0.94 mL of 95% sulfuric (VI) acid were added to the ground glass bottle. Then, 10 mL of 30% hydrogen peroxide solution was gradually added to the mixture. The bottle was closed with a stopper, placed in an ice bath and mixed by a magnetic stirrer for 90 min. Then, the prepared peracetic acid solution was stored tightly closed in a refrigerator at 4 • C. It was found that directly after mixing the reagents, the PAA concentration was 9%, which reached the maximum value of 16% after two days. PAA stored at 4 • C exhibited stability for about one month.
Oxidation experiments were conducted in 100 mL glass beakers with magnetic stirring at room temperature. Solutions of AV1 at a concentration of 100 mg/L were mixed with appropriate volumes of H 2 O 2 or peracetic acid. After a certain period of time, the reaction was stopped by the addition of 2 mL of 20% solution of sodium thiosulfate, and the concentration of the dye was measured using a UV-VIS spectrophotometer. In the same manner, the oxidation experiments assisted by sunlight and the presence of Fe(II) ions were performed. In the case of the light-assisted oxidation process, a prepared mixture of studied compounds with the addition of appropriate portions of H 2 O 2 or peracetic acid was subjected to the irradiation in the solar light simulator (SUNTEST CPS+, ATLAS, Champaign, IL, USA) emitting radiation in the range of 300-800 nm. The temperature in the simulator was maintained at 30 • C. To check the influence of Vis light on the kinetics of AV1 degradation, the lamp worked in one mode set at 750 W/m 2 for all experiments.

Isotherm Experiments
The interactions of dye molecules with the adsorbent can be considered using equilibrium sorption data. Adsorption isotherms explain how pollutants such as azo dyes may be bound by the functional group present on the surface or inside the adsorbent. The Langmuir model considers that the pollutant (i.e., dye) retention occurred on the homogeneous surface of the adsorbent and the monolayer is formed without chemical interactions or bond formation. Freundlich proposed a different isotherm model that assumes adsorption on a heterogonous surface with the formation of a multilayer. The Temkin isotherm states that due to adsorbent-adsorbate interactions, after ignoring very low and high values of concentrations, the adsorption heat of all molecules in the layer will decrease linearly with coverage. The above-mentioned isotherm constants calculated from the corresponding plots are listed in Table 3. As can be seen in Table 3 and Figure 2, the Langmuir isotherm described the adsorption of AV1 on the polystyrene anion exchange resin A520E with the determination coefficient R 2 value of 0.999. The Q 0 and k L values obtained from the plot C e /q e vs. C e were 835.8 mg/g and 0.718, respectively. The observable plateau in Figure 2a indicates a good fit of the experimental data in AV1-A520E system and suggests that the AV1 adsorption onto the polystyrene anion exchange resin A520E occurred with the formation of a monolayer. However, the low value of the k L coefficient confirmed the weak forces between the dye anions and the A520E resin. The Freundlich isotherm parameters k F and 1/n were equal to 305.3 mg 1−1/n L 1/n /g and 0.238, respectively. The 1/n value was lower than unity, which indicates the favorable adsorption of AV1 by the A520E resin. Taking into account the b T value calculated from the Temkin isotherm model, equal to 27.82 J/mol, it can be stated that the mechanism involved in AV1 uptake by A520E is physical adsorption (the bonding energy was below 8 kJ/mol); however, R 2 was found to be 0.881. Analyzing Figure 2b concerning AV1 adsorption on the polyacrylamide anion exchanger S5428, a linear relationship between q e and C e was observed. The Freundlich isotherm model provided the best fitting to experimental data compared to the Langmuir and Temkin models as the determination coefficient R 2 was 0.997. The values of k F and 1/n were equal to 184.5 mg 1−1/n L 1/n /g and 0.967. cerning AV1 adsorption on the polyacrylamide anion exchanger S5428, a linear relati ship between qe and Ce was observed. The Freundlich isotherm model provided the b fitting to experimental data compared to the Langmuir and Temkin models as the de mination coefficient R 2 was 0.997. The values of kF and 1/n were equal to 184.5 mg 1−1/n L and 0.967. The performed studies confirm the very good adsorption parameters of the app anion exchangers in comparison with literature data. The divinylbenzene copolymer w glycidyl methacrylate of trietylenetetramine functional groups (DVB-co-GMA-TETA) hibited a sorption capacity for AV1 of 216.3 mg/g, while for A520 E, it was 835.8 m The experimental results described in [31] confirm that the equilibrium data can be s cessfully described by the Freundlich adsorption model. The adsorbent prepared fr waste red mud during the processing of bauxite ore in the aluminum factory in India w able to remove AV1 at the amount of 1.4 mg/g [52].
To summarize the above considerations, it can be stated that two mechanism of binding by anion exchangers may be involved: these are ion exchange and physical sorption. Ion exchange concerns the electrostatic interaction between functional group the anion exchangers with a positive charge (i.e., quaternary ammonium) and sulf groups of a dye anion. Physical adsorption such as π-π interactions between the ma of the anion exchangers and aromatic rings present in the dye molecules also occurr The acrylamide matrix of S5428 resin is more elastic and hydrophilic than the styre based copolymer of A520E, which is also very important during the retention of la organic species (of high molecular weight) such as dyes. The sorption of dye anions by acrylamide matrix of S5428 with a more aliphatic skeletal structure enables van der W attraction between the resin matrix and the hydrocarbon structure of dye anions. The p ence of the donor oxygen atom of the carbonyl group in the matrix of S5428 promo interactions with protonated -NH2 and -OH groups in the dye molecules. The performed studies confirm the very good adsorption parameters of the applied anion exchangers in comparison with literature data. The divinylbenzene copolymer with glycidyl methacrylate of trietylenetetramine functional groups (DVB-co-GMA-TETA) exhibited a sorption capacity for AV1 of 216.3 mg/g, while for A520E, it was 835.8 mg/g. The experimental results described in [31] confirm that the equilibrium data can be successfully described by the Freundlich adsorption model. The adsorbent prepared from waste red mud during the processing of bauxite ore in the aluminum factory in India was able to remove AV1 at the amount of 1.4 mg/g [52].
To summarize the above considerations, it can be stated that two mechanism of dye binding by anion exchangers may be involved: these are ion exchange and physical adsorption. Ion exchange concerns the electrostatic interaction between functional groups of the anion exchangers with a positive charge (i.e., quaternary ammonium) and sulfone groups of a dye anion. Physical adsorption such as π-π interactions between the matrix of the anion exchangers and aromatic rings present in the dye molecules also occurred. The acrylamide matrix of S5428 resin is more elastic and hydrophilic than the styrenebased copolymer of A520E, which is also very important during the retention of large organic species (of high molecular weight) such as dyes. The sorption of dye anions by an acrylamide matrix of S5428 with a more aliphatic skeletal structure enables van der Waals attraction between the resin matrix and the hydrocarbon structure of dye anions. The presence of the donor oxygen atom of the carbonyl group in the matrix of S5428 promotes interactions with protonated -NH 2 and -OH groups in the dye molecules.

Kinetic Experiments
Very important factors influencing the efficiency of AV1 uptake are the phase contact time between the adsorbent and adsorbate and initial concentration of dye in the solution, as well as the agitation speed. Figure 3a-f shows the impact of the above-mentioned parameters on AV1 sorption on A520E and S5428 and the fitting of experimental data to the three kinetic models: pseudo-first order (PFO), pseudo-second order (PSO) and intraparticle diffusion (IPD). The course of the experimental points on both resins was very similar, as shown in Figure 3a,b. The state of equilibrium in the AV1-A520E and AV1-S5428 systems was observed after 40 min of phase contact time, regardless of the initial AV1 concentration in the system. rameters on AV1 sorption on A520E and S5428 and the fitting of experimental data to the three kinetic models: pseudo-first order (PFO), pseudo-second order (PSO) and intraparticle diffusion (IPD). The course of the experimental points on both resins was very similar, as shown in Figure 3a,b. The state of equilibrium in the AV1-A520E and AV1-S5428 systems was observed after 40 min of phase contact time, regardless of the initial AV1 concentration in the system. The extremely short adsorption time of acid-type dyes on anion exchangers of various types necessary to reach equilibrium has been described in many papers [1][2][3][4]. For example, it is worth mentioning the removal of C.I. Acid Red 18 on the phenol-formaldehyde anion exchanger Amberlyst A23, C.I. Acid Green 16 on the polystyrene anion exchanger Lewatit S6368 [53][54][55]. Table 4 presents the calculated kinetic parameters during 100-500 mg/L AV1 adsorption on both resins. The non-linearity of the log (q e − q t ) vs. t plots of the PFO model and the comparison of the sorption capacities determined from this model with the experimental data confirmed by the low values of R 2 allow us to conclude that it cannot be applied to description of kinetic data in the AV1-anion exchanger system. The PSO kinetic equation describes the experimental data with the highest R 2 values at 0.999. The values of the sorption capacities q e determined from the PSO model are close to the experimental values (q e,exp ), both in the AV1-AE20E and AV1-S5428 systems. The q e values calculated from the PSO model were equal to 10.02, 30.40 and 50.90 mg/g for A520E resin and 10.02, 30.10 and 50.19 mg/g for S5428 resin in 100, 300 and 500 mg/L solutions, respectively. The pseudo-second order rate constants k 2 decreased from 0.181 to 0.005 g/mg min for A520E and from 0.161 to 0.029 g/mg min for S5428 with the increasing dye concentration from 100 to 500 mg/L, respectively. According to the IPD model, if the plots q t vs. t 0.5 give a multilinearity, the adsorption of dye molecules can be controlled by two or more processes. As presented in Figure 4c, the plots of q t vs. t 0.5 are multimodal with three regions: external diffusion (part I), intraparticle diffusion (part II) and surface adsorption (part III). Based on the values of k i1 , k i2 and k i3 and the determination coefficients of each part of the plot, it can be stated that not intraparticle diffusion but external diffusion was involved in the AV1 adsorption on A520E and S5428 and can thus be considered as one of the rate-limiting steps of adsorption. For comparison, the sorption of AV1 (C 0 = 100 mg/L) on DVB-co-GMA-TETA followed intraparticle diffusion, and the rate constant was found to be 10.39 mg/g min 0.5 [31]. 500 mg/L of AV1 using A520E anion exchanger (Figure 4e). For S5428 resin, the values of RE were higher at the beginning of the dye sorption and equaled 39.9%, 43.3% and 35.5%, reaching values of 99.9% (Figure 4f) at equilibrium in 100-500 mg/L solutions, respectively. Adsorption of AV1 on a silica surface modified with 3-aminopropyl-triethoxysilane and N-2-(aminoethyl)-3-aminopropyltrimethoxysilane revealed that 52-99.6% and 79-99.8% of dye can be removed [53].

Impact of Auxiliaries on AV1 Sorption
The dye uptake by the anion exchangers can be influenced by additives such as electrolytes, acids or surfactants present in dyeing baths or effluents. In the current study, the AV1 removal was investigated from solutions with the following composition: 500 mg/L AV1 + 5-25 g/L Na2SO4, 500 mg/L AV1 + 0.25-1 g/L CH3COOH, 500 mg/L AV1 + 0.1-0.25 g/L SDS and 500 mg/L AV1 + 0.1-0.25 g/L TX100. Figure 4 presents the impact of the above-mentioned additives on the amount of AV adsorbed after 15 min of phase contact time. The effect of salt, acid and surfactants in the established concentration range on the amount of retained dye (qt) is more evident for its adsorption on the polystyrene anion exchanger A520E. A slight decrease in AV1 dye adsorption from 41.5 mg/g to 39.1 mg/g and from 41.5 mg/g to 28.4 mg/g was observed in dye baths containing sodium sulfate and sodium dodecyl sulfate-i.e., anionic surfactant-respectively. This can be explained by the competitive adsorption of the sulfate anions with a much smaller size compared to the anionic form of the AV1 dye. For the other systems, there was no noticeable change in the amount of AV1 adsorbed, which is very important from a practical point of view as these auxiliaries are present in both the dye baths and the wastewater.

Desorption Experiments
The desorption of AV1 from the anion exchangers was investigated using eluting agents such as 1 M HCl, 1 M NaOH and 1 M NaCl in aqueous and methanol solutions. As presented in Figure 5 the most effective regenerants were 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH for both AV1 uploaded resins. The dye desorption values for S5428 during the first step of desorption were 70.5% and 86.7% using 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH, respectively. During successive desorption cycles (1-3 cycles), a decrease in efficiency can be observed while keeping the sorption capacity The experimental parameter affecting the dye uptake by the resins is also the adsorption speed. It was observed in Figure 4d that the amount of AV1 adsorbed as a function of time increases with increasing shaking speed from 100 to 240 rpm. However, there was no significant difference between the q t values calculated at 180 rpm and 240 rpm. Importantly, the shaking speed also has no significant effect on the time to reach equilibrium in the adsorption system.

Impact of Auxiliaries on AV1 Sorption
The dye uptake by the anion exchangers can be influenced by additives such as electrolytes, acids or surfactants present in dyeing baths or effluents. In the current study, the AV1 removal was investigated from solutions with the following composition: 500 mg/L AV1 + 5-25 g/L Na2SO4, 500 mg/L AV1 + 0.25-1 g/L CH3COOH, 500 mg/L AV1 + 0.1-0.25 g/L SDS and 500 mg/L AV1 + 0.1-0.25 g/L TX100. Figure 4 presents the impact of the above-mentioned additives on the amount of AV adsorbed after 15 min of phase contact time.
The effect of salt, acid and surfactants in the established concentration range on the amount of retained dye (q t ) is more evident for its adsorption on the polystyrene anion exchanger A520E. A slight decrease in AV1 dye adsorption from 41.5 mg/g to 39.1 mg/g and from 41.5 mg/g to 28.4 mg/g was observed in dye baths containing sodium sulfate and sodium dodecyl sulfate-i.e., anionic surfactant-respectively. This can be explained by the competitive adsorption of the sulfate anions with a much smaller size compared to the anionic form of the AV1 dye. For the other systems, there was no noticeable change in the amount of AV1 adsorbed, which is very important from a practical point of view as these auxiliaries are present in both the dye baths and the wastewater.

Desorption Experiments
The desorption of AV1 from the anion exchangers was investigated using eluting agents such as 1 M HCl, 1 M NaOH and 1 M NaCl in aqueous and methanol solutions. As presented in Figure 5 the most effective regenerants were 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH for both AV1 uploaded resins. The dye desorption values for S5428 during the first step of desorption were 70.5% and 86.7% using 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH, respectively. During successive desorption cycles (1-3 cycles), a decrease in efficiency can be observed while keeping the sorption capacity almost constant. A lower desorption efficiency (59.7% and 73.3%) was observed for the A520E anion exchanger. Earlier performed studies were also in line with the present experiments and revealed that the methanol addition greatly improved desorption efficiency [22][23][24][25][26][27][28][29][30][31]. This is confirmed by the mixed mechanism of dye adsorption on anion exchangers, as described in Section 3.1.1, and the recognition of these adsorbents as selective for dye removal both from aqueous solutions and dyeing baths containing electrolytes and surfactants.
The effect of salt, acid and surfactants in the established concentration range on the amount of retained dye (qt) is more evident for its adsorption on the polystyrene anion exchanger A520E. A slight decrease in AV1 dye adsorption from 41.5 mg/g to 39.1 mg/g and from 41.5 mg/g to 28.4 mg/g was observed in dye baths containing sodium sulfate and sodium dodecyl sulfate-i.e., anionic surfactant-respectively. This can be explained by the competitive adsorption of the sulfate anions with a much smaller size compared to the anionic form of the AV1 dye. For the other systems, there was no noticeable change in the amount of AV1 adsorbed, which is very important from a practical point of view as these auxiliaries are present in both the dye baths and the wastewater.

Desorption Experiments
The desorption of AV1 from the anion exchangers was investigated using eluting agents such as 1 M HCl, 1 M NaOH and 1 M NaCl in aqueous and methanol solutions. As presented in Figure 5 the most effective regenerants were 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH for both AV1 uploaded resins. The dye desorption values for S5428 during the first step of desorption were 70.5% and 86.7% using 1 M HCl + 50% v/v MeOH and 1 M NaCl + 50% v/v MeOH, respectively. During successive desorption cycles (1-3 cycles), a decrease in efficiency can be observed while keeping the sorption capacity almost constant. A lower desorption efficiency (59.7% and 73.3%) was observed for the A520E anion exchanger. Earlier performed studies were also in line with the present experiments and revealed that the methanol addition greatly improved desorption efficiency [22][23][24][25][26][27][28][29][30][31]. This is confirmed by the mixed mechanism of dye adsorption on anion exchangers, as described in Section 3.1.1, and the recognition of these adsorbents as selective for dye removal both from aqueous solutions and dyeing baths containing electrolytes and surfactants.

H 2 O 2 -Based Oxidation
Hydrogen peroxide is an environmentally friendly oxidant with a wide range of applications in various industries and in laboratory practice [56].  (11) In the Fenton reaction, the production of HO˙occurs in an acidic environment in the presence of Fe 2+ . The decomposition of H 2 O 2 occurs due to the fact that Fe 2+ ions play the role of an electron donor while oxidizing to Fe 3+ : (12) An oxo-iron complex (Fe IV O 2+ ) can be also formed in the Fenton process. It is a more selective and weaker oxidant than HO˙but has a longer lifetime [57]: Fe 3+ formed in reaction (6) can also react with H 2 O 2 , but the rate of this reaction is low [58]: To study the process of dye removal during oxidation, the absorbance changes at absorption maximum were monitored and converted into the AV1 concentration by using calibration plots. Figure 6 shows the effect of H 2 O 2 alone (Figure 6a) as well as H 2 O 2 activated by simulated solar light (Figure 6b) and Fe 2+ ions (Figure 6c).

H2O2-Based Oxidation
Hydrogen peroxide is an environmentally friendly oxidant with a wide range of applications in various industries and in laboratory practice [56]. Breaking the O-O bond in the H2O2 molecule occurs quite easily under the influence of various catalysts. The most commonly used catalysts are UV or sunlight and iron ions (Fenton reaction). In the presence of light, H2O2 decomposes into two hydroxyl radicals: H2O2 + hν→ 2 HO˙ (11) In the Fenton reaction, the production of HO˙ occurs in an acidic environment in the presence of Fe 2+ . The decomposition of H2O2 occurs due to the fact that Fe 2+ ions play the role of an electron donor while oxidizing to Fe 3+ : Fe 2+ + H2O2→ Fe 3+ + OHˉ+HO˙ (12) An oxo-iron complex (Fe IV O 2+ ) can be also formed in the Fenton process. It is a more selective and weaker oxidant than HO˙ but has a longer lifetime [57]: Fe 3+ formed in reaction (6) can also react with H2O2, but the rate of this reaction is low [58]: Fe 3+ + H2O2→ Fe 2+ + HO2˙ +H + (14) To study the process of dye removal during oxidation, the absorbance changes at absorption maximum were monitored and converted into the AV1 concentration by using calibration plots. Figure 6 shows the effect of H2O2 alone (Figure 6a) as well as H2O2 activated by simulated solar light (Figure 6b) and Fe 2+ ions (Figure 6c). The experiments with hydrogen peroxide alone and with hydrogen peroxide activated by simulated solar radiation were conducted at a pH of 9, which, according to the literature, is optimal for the oxidation process [59]. The Fenton processes were conducted at a pH of 3, which provides the highest oxidation efficiency and prevents the removal of Fe 2+ ions by precipitation as Fe(OH) 2 [60]. To determine the influence of the amount of oxidant on the course of the process, tests were carried out for three concentrations of H 2 O 2 : 35, 70 and 100 mg/L. The data presented in Figure 6 indicate that, under the action of H 2 O 2 , there is a slight decrease in the concentration of AV1, and C/C 0 take values between 0.65 and 0.73, depending on the concentration of the oxidant. In the case of H 2 O 2 activated by simulated solar radiation, after 120 min of oxidation, C/C 0 equals 0.09 and 0.24, which means that 9% to 24% of the original dye concentration remains in the system. As a result of the Fenton process, after 15 min, the C/C 0 of AV1 in the system decrease to 0.06-0.07. After 45-60 min of oxidation in the H 2 O 2 /Fe 2+ system, the concentration of AV1 decreases to values undetectable by the spectrophotometric method. The concentration of the oxidant is an important factor in the effectiveness of the oxidation process. When the initial H 2 O 2 concentration is growing, the degradation rate of AV1 increases (Figure 6a-c). This is associated with an increase in the concentration of reactive˙OH radicals along with a greater concentration of H 2 O 2 . The greatest differences in the course of UV1 degradation processes in the presence of different concentrations of hydrogen peroxide were observed for the H 2 O 2 /sunlight system. In this system, after 120 min of oxidation, the C/C 0 values were 0.24, 0.16 and 0.9 when the oxidant concentration was 35, 70 and 100 mg/L, respectively.
Concentration data plotted against time on a semi-log scale form straight lines (Figure 7), which indicates that the all oxidation processes based on the use of H 2 O 2 follow pseudofirst-order kinetics. The slope of the corresponding line equals the rate constant (k 1 ), according to Equation (15): Fe 2+ ions by precipitation as Fe(OH)2 [60]. To determine the influence oxidant on the course of the process, tests were carried out for three H2O2: 35, 70 and 100 mg/L. The data presented in Figure 6 indicate tha of H2O2, there is a slight decrease in the concentration of AV1, and C/ tween 0.65 and 0.73, depending on the concentration of the oxidant. I activated by simulated solar radiation, after 120 min of oxidation, C/ 0.24, which means that 9% to 24% of the original dye concentration rem As a result of the Fenton process, after 15 min, the C/C0 of AV1 in the 0.06-0.07. After 45-60 min of oxidation in the H2O2/Fe 2+ system, the con decreases to values undetectable by the spectrophotometric method. Th the oxidant is an important factor in the effectiveness of the oxidation initial H2O2 concentration is growing, the degradation rate of AV1 inc c). This is associated with an increase in the concentration of reactive ˙ with a greater concentration of H2O2. The greatest differences in the cou dation processes in the presence of different concentrations of hydrog observed for the H2O2/sunlight system. In this system, after 120 min of values were 0.24, 0.16 and 0.9 when the oxidant concentration was 35 respectively.
Concentration data plotted against time on a semi-log scale form ure 7), which indicates that the all oxidation processes based on the u pseudo-first-order kinetics. The slope of the corresponding line equal (k1), according to Equation (15): Therefore, the half-life of AV1 in the considered oxidation system from the following relationship: The time required to remove 99% of the original amount of dye from the following formula: Therefore, the half-life of AV1 in the considered oxidation systems can be calculated from the following relationship: The time required to remove 99% of the original amount of dye can be calculated from the following formula: As could be seen in Figure 7, in the case of the H 2 O 2 alone and H 2 O 2 /sunlight systems, one equation describes the rate of oxidation over the entire time range. However, when we consider Fenton's reaction, it could be seen that the process starts at a higher speed, and then the speed is decreased. In this case, the kinetic diagram can be divided into two areas in which the linear course of the function ln(C 0 /C) is described by different equations. The values of the determination coefficient describing the fit of the experimental data to the theoretical course of the function, as well as k 1 and t 1/2 values for AV1 degradation, are included in Table 5. Table 5. Determination coefficients (R 2 ) describing the fit of the experimental data to the theoretical course of the ln(C/C 0 ) = f (t) function, first-order rate constant (k 1 ), half-life time (t 1/2 ) and time required to achieve 99% (t 99% ) AV1 removal by H 2 O 2 (C H 2 O 2 = 35 mg/L)-based oxidation. As can be seen in Table 4, the removal of AV1 by oxidation with H 2 O 2 is a relatively lengthy process. It occurs most quickly in the Fenton system. Similar results are obtained in studies on the removal of other azo dyes [35]. Zuorro and Lavecchia, in their work on the removal of Reactive Green 19, obtained a shorter dye removal time when H 2 O 2 was assisted by UV radiation [36]. However, such a system consumes large amounts of energy, while the use of sunlight is a cheaper and more environmentally friendly solution.

PAA Based Oxidation
So far, the use of PAA as an oxidant in AOPs has been relatively little researched, and only single studies concern its use for the removal of organic compounds from water and wastewater [41]. For over a dozen years, PAA has been considered to be a very efficient disinfectant. Currently, it is increasingly used for the final sterilization of treated wastewater [42,61]. Peracetic acid undergoes slow autodecomposition (7.36 × 10 −3 1/M·s) at room temperature [41]. Due to its high oxidation potential, it is able to react with organic micropollutants present in water. Under the influence of light, the O-O bond in PAA decomposes, which leads to the formation of HO˙and acetyloxyl radicals (CH 3 C(O)O˙): (18) PAA can also be activated with Fe 2+ , analogous to H 2 O 2 in the Fenton process: The formed radicals can react with PAA, acetic acid and H 2 O 2 to form secondary radicals-among others, superoxide radical anion (O 2 −˙), hydroperoxyl radical (HO 2˙) and methyl radical (˙CH 3 ). Since H 2 O 2 is also present in the PAA solution, the reactions described by Equations (6)-(8) may also take place during the oxidation. However, the literature data show that these processes are characterized by a much slower speed than those involving PAA [58].
Experiments with peracetic acid were conducted at a pH of 7 when the oxidant was used alone and when the oxidant was activated by solar radiation. A pH of 3 was chosen as optimal for systems in which PAA was activated with iron ions [41]. Figure 8 shows the effect of contact with PAA alone, PAA/sunlight, PAA/Fe 2+ and PAA/Fe 2+ /sunlight on the concentration of AV1, calculated from the absorbance changes. The research was carried out for three PAA concentrations (35,70, 100 mg/L) in the case of the first two experiments. The data presented in Figure 8a indicate that PAA alone causes very little decolorization of AV1. The C/C 0 value after 120 min of the experiment decreased to 0.75-0.82. In the PAA/sunlight system (Figure 8b), the dye content after 120 min of the experiment decreased to 29-42% of the initial concentration. In the case of PAA alone and PAA activated by sunlight, the degree of degradation increases with the increase in the concentration of the oxidant, which is related to the greater number of radicals formed during the processes. The differences in the degree of AV1 removal in the solutions with the highest and the lowest oxidant concentration range from a few to a dozen percentage points. The experiments in PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems were performed for five concentrations of the oxidant: 12.5, 35, 50, 70 and 100 mg/L (Figure 8c,d). In the first of these systems, the C/C 0 of AV1 achieves values from 0 to 0.08 after 120 min of oxidation. In total, 5% of the initial AV1 concentration remains after 5 min of oxidation in solutions where the concentration of the PAA is 12.5 or 35 mg/L. When the oxidant concentration is 50 and 70 mg/L, 95% degradation is achieved after 75 and 90 min of the experiment, respectively. At an oxidant concentration of 100 mg/L, this degree of degradation is not achieved within the 120 min of the experiment. In the PAA system, the concentration of AV1 is reduced to a level from 0% to 2% of the initial value within 120 min. AV1 solution discoloration at the level of 95% occurs after 5 min of contact with the oxidant, when the concentration of PAA is 12.5 or 35 mg/L and after 15 min, when C PAA is 50 or 70 mg/L. With a C PAA of 100 mg/L, 95% decolorization occurs within 60 min. We found that 35 mg/L is the optimal oxidant concentration for the most efficient dye removal in PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems. Only slightly worse results are achieved when the concentration is 12.5 mg/L. Fe 2+ ions activate PAA and the H 2 O 2 in equilibrium with it, causing the intensive production of radicals with high oxidizing potential. These radicals react and quench each other, which lowers the oxidizing potential of the system.
As can be seen in Figure 9, all oxidation processes with the use of PAA proceed according to the pseudo-first-order kinetics. The correlation coefficients for all considered processes are 0.99 or more, which indicates a very good fit of the experimental data to the theoretical course of the function ln(C/C 0 ) = f (t). Table 6 shows the values of R 2 , k 1 , t 1/2 and t 99% for PAA-based AV1 degradation. The dye removal is very fast in PAA/Fe 2+ /sunlight (k 1 = 0.3897 min −1 ) and PAA/Fe 2+ (k 1 = 0.3527 min −1 ) systems, and after 15 min, the solution is completely discolored. The processes in the PAA and PAA/sunlight systems run at a low speed, the constant rates are 0.0017 and 0.0070 min −1 , respectively.
Processes 2021, 9,1911 15 of 20 Experiments with peracetic acid were conducted at a pH of 7 when the oxidant was used alone and when the oxidant was activated by solar radiation. A pH of 3 was chosen as optimal for systems in which PAA was activated with iron ions [41]. Figure 8 shows the effect of contact with PAA alone, PAA/sunlight, PAA/Fe 2+ and PAA/Fe 2+ /sunlight on the concentration of AV1, calculated from the absorbance changes. The research was carried out for three PAA concentrations (35,70, 100 mg/L) in the case of the first two experiments. The data presented in Figure 8a indicate that PAA alone causes very little decolorization of AV1. The C/C0 value after 120 min of the experiment decreased to 0.75-0.82. In the PAA/sunlight system (Figure 8b), the dye content after 120 min of the experiment decreased to 29-42% of the initial concentration. In the case of PAA alone and PAA activated by sunlight, the degree of degradation increases with the increase in the concentration of the oxidant, which is related to the greater number of radicals formed during the processes. The differences in the degree of AV1 removal in the solutions with the highest and the lowest oxidant concentration range from a few to a dozen percentage points. The experiments in PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems were performed for five concentrations of the oxidant: 12.5, 35, 50, 70 and 100 mg/L (Figure 8c,d). In the first of these systems, the C/C0 of AV1 achieves values from 0 to 0.08 after 120 min of oxidation. In total, 5% of the initial AV1 concentration remains after 5 min of oxidation in solutions where the concentration of the PAA is 12.5 or 35 mg/L. When the oxidant concentration is 50 and 70 mg/L, 95% degradation is achieved after 75 and 90 min of the experiment, respectively. At an oxidant concentration of 100 mg/L, this degree of degradation is not achieved within the 120 min of the experiment. In the PAA system, the concentration of AV1 is reduced to a level from 0% to 2% of the initial value within 120 min. AV1 solution discoloration at the level of 95% occurs after 5 min of contact with the oxidant, when the concentration of PAA is 12.5 or 35 mg/L and after 15 min, when CPAA is 50 or 70 mg/L. With a CPAA of 100 mg/L, 95% decolorization occurs within 60 min. We found that 35 mg/L is the optimal oxidant concentration for the most efficient dye removal in PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems. Only slightly worse results are achieved when the concentration is 12.5 mg/L. Fe 2+ ions activate PAA and the H2O2 in equilibrium with it, causing the intensive production of radicals with high oxidizing potential. These radicals react and quench each other, which lowers the oxidizing potential of the system. As can be seen in Figure 9, all oxidation processes with the use of PAA proceed according to the pseudo-first-order kinetics. The correlation coefficients for all considered processes are 0.99 or more, which indicates a very good fit of the experimental data to the theoretical course of the function ln(C/C0) = f(t). Table 6 shows the values of R 2 , k1, t1/2 and t99% for PAA-based AV1 degradation. The dye removal is very fast in PAA/Fe 2+ /sunlight (k1 = 0.3897 min −1 ) and PAA/Fe 2+ (k1 = 0.3527 min −1 ) systems, and after 15 min, the solution is completely discolored. The processes in the PAA and PAA/sunlight systems run at a low speed, the constant rates are 0.0017 and 0.0070 min −1 , respectively.

AV1 Removal Efficiency in Oxidation Processes
The efficiency of AV1 removal in oxidation processes was determined both on the basis of the degree of decolorization and on the basis of changes in the COD value (Figure  As can be seen in Figure 9, all oxidation processes with the use of PAA cording to the pseudo-first-order kinetics. The correlation coefficients for all processes are 0.99 or more, which indicates a very good fit of the experimenta theoretical course of the function ln(C/C0) = f(t). Table 6 shows the values of R t99% for PAA-based AV1 degradation. The dye removal is very fast in PAA/F (k1 = 0.3897 min −1 ) and PAA/Fe 2+ (k1 = 0.3527 min −1 ) systems, and after 15 min, is completely discolored. The processes in the PAA and PAA/sunlight syste low speed, the constant rates are 0.0017 and 0.0070 min −1 , respectively.

AV1 Removal Efficiency in Oxidation Processes
The efficiency of AV1 removal in oxidation processes was determined basis of the degree of decolorization and on the basis of changes in the COD v  Table 6. Determination coefficient (R 2 ) describing the fit of the experimental data to the theoretical course of the ln(C/C 0 ) = f (t) function, first-order rate constant (k 1 ), half-life time (t 1/2 ) and time required to achieve 99% (t 99% ) AV1 removal by PAA (C PAA = 35 mg/L) based oxidation.

AV1 Removal Efficiency in Oxidation Processes
The efficiency of AV1 removal in oxidation processes was determined both on the basis of the degree of decolorization and on the basis of changes in the COD value ( Figure 10). The COD value determined by the potassium dichromate(VI) method is 145 mg O 2 /L for the 100 mg/L AV1 solution, which was used in all oxidation experiments. The comparison of the efficiency of oxidation processes based on the use of H 2 O 2 and PAA shows that the best oxidation results are provided by systems in which the oxidant is activated with iron ions. 10). The COD value determined by the potassium dichromate(VI) method is 145 mg O2/L for the 100 mg/L AV1 solution, which was used in all oxidation experiments. The comparison of the efficiency of oxidation processes based on the use of H2O2 and PAA shows that the best oxidation results are provided by systems in which the oxidant is activated with iron ions. As shown in Figure 10a, the decolorization efficiency in systems with PAA and Fe 2+ ions takes values close to 100% in a shorter time than in the H2O2/Fe 2+ system. This is probably related to the higher oxidation potential (E0); i.e., PAA: E0 = 1.96V; H2O2: E0 = 1.78 V [42]. The higher efficiency of PAA oxidation is probably also influenced by the fact that the oxygen-oxygen bond energy for this compound is lower (170 kJ/mol) than for H2O2 (210 kJ/mol). Furthermore, the peroxy bond in the PAA molecule is longer than in H2O2 (1.443 Å and 1.427 Å , respectively), so it is easily broken, leading to the formation of hydroxyl and acetate radicals [41]. The COD reduction efficiency presented in Figure 10b is related to the gradual mineralization of AV1; i.e., its degradation to inorganic ions. As can be seen, the mineralization of the oxidized solution takes place slower than its decolorization. The obtained results are consistent with literature reports; similar observations were made for the oxidation of Erythrosine B, Orange G and Reactive Green 19 by H2O2/UV, photo-Fenton, electro-Fenton, UV-electro-Fenton and solar-electro-Fenton processes [36,37,40]. After 120 min of oxidation, almost complete mineralization of the solution takes place in all systems where Fe 2+ ions are present. The confirmation of complete mineralization is very important as it confirms the degradation of AV1 to simple inorganic ions and not to potentially toxic, and at the same time colorless, intermediates [36].

Conclusions
This paper describes the results of C.I. Acid Violet 1 (azo class dye) removal from aqueous solutions and dyeing baths using two techniques-adsorption and advanced oxidation-taking into consideration different experimental conditions. In adsorption tests, the selectivity of the macroporous strongly basic anion exchangers (Purolite A520E and Lewatit S5428) with quaternary ammonium functional groups differing in the chemical composition of the matrix was evaluated. Large values of the sorption capacities of both resins described by the Langmuire and Freundlich isotherm model allowed their use in the removal of AV1 dye, also in the presence of salts and surfactants. The dye removal efficiency reached more than 99% after 240 min in 100-500 mg/L solutions using A520E and S5428. The effective regeneration of the adsorbents has also been proposed, which enables their practical application. As shown in Figure 10a, the decolorization efficiency in systems with PAA and Fe 2+ ions takes values close to 100% in a shorter time than in the H 2 O 2 /Fe 2+ system. This is probably related to the higher oxidation potential (E 0 ); i.e., PAA: E 0 = 1.96V; H 2 O 2 : E 0 = 1.78 V [42]. The higher efficiency of PAA oxidation is probably also influenced by the fact that the oxygenoxygen bond energy for this compound is lower (170 kJ/mol) than for H 2 O 2 (210 kJ/mol). Furthermore, the peroxy bond in the PAA molecule is longer than in H 2 O 2 (1.443 Å and 1.427 Å, respectively), so it is easily broken, leading to the formation of hydroxyl and acetate radicals [41]. The COD reduction efficiency presented in Figure 10b is related to the gradual mineralization of AV1; i.e., its degradation to inorganic ions. As can be seen, the mineralization of the oxidized solution takes place slower than its decolorization. The obtained results are consistent with literature reports; similar observations were made for the oxidation of Erythrosine B, Orange G and Reactive Green 19 by H 2 O 2 /UV, photo-Fenton, electro-Fenton, UV-electro-Fenton and solar-electro-Fenton processes [36,37,40]. After 120 min of oxidation, almost complete mineralization of the solution takes place in all systems where Fe 2+ ions are present. The confirmation of complete mineralization is very important as it confirms the degradation of AV1 to simple inorganic ions and not to potentially toxic, and at the same time colorless, intermediates [36].

Conclusions
This paper describes the results of C.I. Acid Violet 1 (azo class dye) removal from aqueous solutions and dyeing baths using two techniques-adsorption and advanced oxidation-taking into consideration different experimental conditions. In adsorption tests, the selectivity of the macroporous strongly basic anion exchangers (Purolite A520E and Lewatit S5428) with quaternary ammonium functional groups differing in the chemical composition of the matrix was evaluated. Large values of the sorption capacities of both resins described by the Langmuire and Freundlich isotherm model allowed their use in the removal of AV1 dye, also in the presence of salts and surfactants. The dye removal efficiency reached more than 99% after 240 min in 100-500 mg/L solutions using A520E and S5428. The effective regeneration of the adsorbents has also been proposed, which enables their practical application.
The results of oxidation experiments indicate that AOPs based on H 2 O 2 and PAA can effectively remove AV1 from its water solutions. Both sunlight and iron ions used as oxidation activators accelerate the degradation of the tested dye. The Fenton reaction, PAA/Fe 2+ and PAA/Fe 2+ /sunlight systems are most effective in both the decolorization and mineralization of AV1 solutions. It was found that PAA, which is an oxidant that is rarely used and relatively little studied, works more efficiently and faster than H 2 O 2 . In addition, oxidation with PAA requires lower concentrations of the oxidant than in the case of H 2 O 2 , which reduces the cost of the process and the impact on the environment.
In conclusion, the proposed techniques can be considered as highly effective for the removal of AV1, and the performed studies are of significant importance not only from a scientific but also from a practical point of view, especially in the treatment of wastewaters containing acid-type dyes.

Data Availability Statement:
The data presented in this study are available in this article.