Investigation of Ni–Fe–Cu-Layered Double Hydroxide Catalysts in Steam Reforming of Toluene as a Model Compound of Biomass Tar

: This work focused on the synthesis of a catalyst based on layered double hydroxides with a molar cation concentration Ni/Cu/Fe/Mg/Al of 30/5/5/40/20 and its performance in the steam reforming of toluene as a model compound of biomass tar. Its performance at different temperatures (500, 600, 700, 800, and 900 ◦ C) and steam/carbon molar ratios (S/C ratios) (1, 2, 4, 6, 8) was studied. The contact time used was 0.32 g h mol − 1 . The catalyst obtained allowed us to reach 98–99.87% gas conversion of toluene with a low carbon deposition on catalyst surface (1.4 wt %) at 800 ◦ C and S/C = 4. In addition, conversions in the range of 600–700 ◦ C were higher than 80% and 90%, respectively, and the type of carbon deposited on the catalyst was found to be ﬁlamentous, which did not signiﬁcantly reduce the performance of the catalyst.


Introduction
The increase in demand for energy from fossil fuels that has taken place in recent decades is mainly due to the increase in population and living standards.In order to mitigate this situation, efforts are being made to encourage the substitution of fossil fuels by other renewable energy sources.
Among these alternatives, gasification is presented as a promising technology, in which syngas can be obtained from biomass as a renewable energy source.Gasification of biomass into syngas is expected to be used in various fields such as power generation and the production of hydrogen and liquid fuels (e.g., methanol and Fischer-Tropsch fuel) [1].
However, this syngas also contains some impurities, such as organic tars, which need to be removed before its application.Tars are the main contaminants in the syngas, and its content varies with the type of raw material and gasifier from 5 to 100 g/Nm 3 .Their maximum allowable content depends on the end use, usually being 5 mg/Nm 3 in gas turbines and 100 mg/Nm 3 in internal combustion engines [2].Tars are a complex mixture of aromatic and oxygenated hydrocarbons that may cause several operational problems.Within the compounds that constitute the tar, toluene is among the most important, besides naphthalene, indene, and acenaphthylene [3].The requirement to remove tars introduces significant cost and complexity into the overall gasification process.Among the different strategies to remove tars from the gas, catalytic steam reforming is a useful technic.
LDHs have received special attention due to their relatively simple synthesis, low cost, and excellent catalytic properties.LDHs can be calcined to give a stable and homogeneous mixture of oxides with a very small crystal size.These materials when reduced favor a high dispersion of metals, which contributes to avoid the deactivation of the catalyst [8,9].
On the other hand, nickel-based catalysts have been widely used in tar reforming because of is very effective in reforming of tars [10], whose performance can be improved by the addition of promoters such as Fe, Ce, Cu, Pd, Zn, and Ca [1,5,6,8,9].
In this context, the objective of this work is to study steam reforming of toluene as a tar model compound over nickel-based LDH catalysts.

Catalyst Preparation
Ni-Fe-Cu/LDH was prepared by coprecipitation from aqueous solutions at room temperature.Two solutions were prepared-solution A containing metal precursors, and prepared from their respective nitrates: Ni(NO 3 ) 2 6H 2 O, Cu(NO 3 ) 2 3H 2 O, Fe(NO 3 ) 3 9H 2 O, Mg(NO 3 ) 2 6 H 2 O, and Al(NO 3 ) 3 9 H 2 O. Solution A was 4M NO 3 −2 , and was prepared to get the following molar cation concentration: Ni/Fe/Cu/Mg/Al: 30/5/5/40/20.Solution B contained Na 2 CO 3 (0.22 M) and NaOH (3.56 M).Then, 100 mL of solution A and B was slowly dropped by HPLC pumps under vigorous stirring over 100 mL deionized water.To ensure a good mix and dispersion, we used a homogenizer (Model IKA magic, IKA-Werke GmbH & Co. KG, Staufen, Germany) as the reactor.The temperature of the solution was kept constant at 60 • C by means a thermostatic bath.The pH of the solution was also maintained constant during all test by means of a control system that added solution NaOH 1 M to obtain the pH at 10 to ensure the co-precipitation of the metallic salts.
The gel formed was aged for 20 h at 100 • C under reflux in order to improve its crystalline characteristics.The solid obtained was then filtered and washed with distilled water at 90 • C until the solution was a conductivity bellow 30 µS cm −1 [11].The LDH formed was dried at 105 • C overnight, and then finally crushed and calcined using a heating rate of 5 • C min −1 , from room temperature to 800 • C and keeping at this temperature for 3 h.
In order to obtain a greater understanding of the structure of the catalyst, we synthesized three additional LDHs following the same procedure.Table 1 shows the composition of all synthesized LDHs.The chemical element analysis of as-synthesized catalysts was performed using the inductively coupled plasma-optical emission spectroscopy (ICP-OES) on the Optima 4300 DV (Perkin Elmer, Waltham, MA, USA).Prior to the analysis, the solid (0.05 g) was dissolved in 4 mL HNO 3 and then was heated to 100 • C for 5 min, to 170 for 15 min, and to 240 • C for 10 min; kept in isothermal condition for 15 min; and finally filtered and diluted.

Characterization of the Calcination Process
In order to analyze the calcination, process, we conducted a thermogravimetric analysis (TGA).
Thermogravimetric analysis was performed on a DTG-60H TG-DTA analyzer (Shimadzu Co. Ltd., Kyoto, Japan).The analyses were carried out using air with a flow rate of 50 mL min −1 , and a heating rate of 10 • C min −1 , from room temperature to 900 • C. The amount of sample analyzed was ≈3 mg.This analysis allowed us to determine the weight loss of a sample as a function of temperature and time (TG curve).In addition, the derivative of the TG signal (DTG curve) helped to determine the number of main thermal processes that took place, as well as their temperature intervals.

Temperature-Programmed Reduction (TPR) Analysis
TPR analyses were performed on Auto Chem II 2920 analyzers (Micromeritics Instrument Corporation, Norcross, GA, USA) with a thermal conductivity detector (TCD) used to quantify the amount of H 2 consumed during the analysis.
TPR was used to determine the reducible species and the corresponding reduction temperatures.Before measurement, a 0.20 g sample was dried by passing 50 mL min -1 of Ar up to 150 • C at a heating rate of 10 • C min −1 , and holding time under these conditions 30 min.Then, the reduction of the sample was carried out by means of 50 mL min −1 of 5% H 2 /Ar to 950 • C min −1 , heating rate 10 • C min −1 , and holding time of 30 min.

X-Ray Diffraction (XRD) Analysis
Powder X-ray diffraction (XRD) measurements were performed on a D8 Discover (Bruker, Billerica, MA, USA) using Cu Kα radiation (λ = 0.154 nm) generated at 40 kV and 40 mA.The identification of the diffraction patterns was performed using the Joint Committee of Powder Diffraction Standards (JCPDS) database.
XRD analyses are suitable for determining lattice parameters and particle diameter.Thus, for example, LDHs are a hexagonal system whose most significant lattice parameters are a and c-a represents the average cation-cation distance within the layers and c represents the distance between the brucite-like layer and the inter-layer [12,13].The relationship between lattice parameter and interplanar spacing d hkl is given by 1 where (h, k, l) are Miller indices, a and c are the lattice parameters, and d is interplanar spacing [14].Lattice parameter a and c are calculated from the (110) and (003) plane, respectively obtained from Equations (4) and (5).
The interplanar spacing of the (110) and (003) crystal planes was estimated by Bragg's law, which can be represented by Equation (6).
where n, λ, and θ are the order, X-ray wavelength, and diffraction angle, respectively.Using Equations ( 4)-( 6) and the diffraction angle obtained from the XRD pattern, we can obtain the lattice parameters a and c.
The crystallite size (D) was calculated by Scherrer Equation ( 7) where K is the shape factor (K = 0.89), β is the full width at half maximum (FWHM) of the analyzed diffraction peak in radians, and θ is the Bragg angle.
A similar procedure was used to determine the lattice parameters of calcined and reduced LDHs, but using Equation (8), which is characteristic of a face-centered cubic (fcc) structure such as that of NiO and metallic Ni.

Scanning Electron Microscopy (SEM)
A high-resolution scanning electron microscope (SEM) FEI ESEM Quanta 200 (FELMI-ZFE, Graz, Austria) was used to analyze the surface morphology of the as-synthetized and used catalyst.

Type and Amount of Carbonaceous Species Deposited on the Catalyst
The type of carbonaceous material deposited on the surface of the catalyst at the end of the steam reforming reaction was performed on a DTG-60H TG-DTA analyzer (Shimadzu Co. Ltd., Kyoto, Japan).The analyses were carried out using air with a flow rate of 50 mL min −1 , and a heating rate of 20 • C min −1 , from room temperature to 1000 • C. The amount of sample analyzed was ≈3 mg.This method was used to determine the type of carbon deposited by its relationship to its oxidation temperature [15].
The amount of carbon formed on the surface of the catalyst after reaction was measured using an elemental TruSpec CHN analyzer (Leco, St. Joseph, MI, USA).

Catalytic Tests
Steam reforming of toluene used as a model compound of tar was carried out using a fixed-bed reactor made of Hastelloy alloy steel, with an inner diameter of 10 mm and a length of 500 mm (Figure 1).The reactor was heated by a tubular electric furnace coupled to the reactor.The process temperature was measured by a K-type thermocouple placed in the center of the bed and controlled using a controller in closed loop (DEMEDE, Spain).
In each test, 250 mg of calcined catalyst was placed in the middle of the reactor on a 316 stainless steel sintered porous metal filter disc with an internal pore size of 40 µm.Quartz wool was used above and below the bed to help catalyst inside the reactor.
Prior to each test, the system was purged with 50 mL min −1 N 2 for 15 min, and then the catalyst was reduced with a flow of H 2 and N 2 (H 2 /N 2 = 50/20 mL min −1 ) at 900 • C for 2 h to transform Mg(Ni,Al)O periclase species of Ni 2+ into well-dispersed Ni particles [16].After reduction, the system was purged again with 50 mL min −1 N 2 for 15 min while the temperature was kept at the desired temperature of the steam reforming 500-900 • C. Once the system was purged, the steam reforming reaction was started, with the duration of each test being 1 h.To do this, the water and the toluene were fed into a preheater by means of a HPLC pump and syringe pump, respectively.Moreover, to ensure a concentration of toluene in the gas phase of 1.50 vol %, we fed a current of N 2 into the preheater through a mass flow controller.This preheater was maintained at 250 • C in order to ensure a complete vaporization of the feedstock before entering the fixed bed reactor containing the catalyst.To prevent condensation and to ensure that feedstock was maintained in a homogeneous vapor phase, we placed the preheater and the reactor in a chamber that was kept warm at 200 • C.
The reaction products were then passed through a cold trap to condense unreacted toluene and water in the effluent stream.All the non-condensed gases (H 2 , N 2 , CO, CO 2 , and CH 4 ) were analyzed online by gas chromatography using a chromatograph MicroGC CP4900 (Varian Inc., Palo Alto, CA, USA) with two channels, one equipped with a molecular sieve column and another one with a Polar Plot Q column, and both coupled to a thermal conductivity detector (TCD).The unreacted toluene and benzene produced were collected at the end of each test and analyzed offline by gas chromatography, using a 6890 N gas chromatograph coupled with mass spectrometer 5973 Network (Agilent, Santa Clara, CA, USA).
Different tests were developed using reaction temperatures of 500, 600, 700, 800, and 900 • C and steam/carbon molar ratios (S/C ratios) of 1, 2, 4, 6, and 8.The total flow rate of the product gases was calculated by means of a mass balance to the nitrogen stream.The contact time in the steam reforming reaction was calculated in all tests to be W/F = 0.32 g h mol −1 .F is the total molar flow of the feedstock (toluene, water, and nitrogen) and W represents the weight of the catalyst.
Table 2 summarizes the operating conditions for each S/C ratio.As can be seen in Table 2, the toluene flow rate was kept at 0.2 mmol min −1 , the water flow rate was adjusted to obtain the desired S/C, and the nitrogen flow rate was adjusted to ensure the same concentration of toluene in the feedstock and the same contact time.Benzene yield was evaluated by a carbon balance between the carbon from the benzene formed and the carbon from the toluene at the feed, as shown in Equation (9).
In the same way, the conversion of toluene to gases was calculated by a carbon balance between the carbon from the gaseous products formed (CO, CO 2 , and CH 4 ), and the carbon from the toluene at the feed.
where n CO , n CO2 , n CH4 , and n C7H8 represent the molar flow rate of CO, CO 2 , CH 4 , and toluene, respectively.The molar gas composition of each gas (H 2 , CO, CO 2 , and CH 4 ) was calculated as Equation (11).

Chemical Element Analysis Results
The chemical element analysis of as-synthesized and calcined catalysts is showed in Table 3.The results showed that the LDH obtained corresponded to the one initially synthesized, although a slightly higher substitution of Mg 2+ by M 2+ cations (Ni 2+ and Cu 2+ ) was observed.These results also showed that the precipitation of the compounds took place almost in its totality, without important loss of reagent.After calcination at 800 • C, it was also observed that the composition remained almost constant.

TGA of the As-Synthesized Ni-Fe-Cu/LDH
The calcination process of the as-synthesized Ni-Fe-Cu/LDH was studied by performing TGA analysis (Figure 2).The TG curve (Figure 2) showed three main regions of mass loss.The first region was observed between ambient temperature up to 210 • C, which was related with the first two peaks in the DTG signal with maximum values at 100 and 180 • C. The first peak of the DTG curve (peak I) was related with a mass loss of 2.2% from the TG curve and occurring from ambient temperature up to around 100 • C, and was associated with the elimination of water, physically adsorbed on the external surface of the particle.The peak II at about 180 • C presented a mass of 8.7% in the interval 100-210 • C of the TG curve, and may be attributed to the removal of -OH and water from the brucite-like layer [17].The second region in the TG curve was located between 210 and 400 • C and it corresponded to the second DTG peak, with maximum temperature of 360 • C. The average mass loss in this second region was around 18.5% and was attributed to the dehydroxylation of the brucite type layers, with decomposition of carbonate anions (decarbonization).From this temperature, called the collapse of the layers up to 800 • C, occurred the rearrangement of the structure with the formation of aluminum oxides, magnesia (periclase phase), and the formation of other metal and mixed oxides reaching the structure a great thermal stability, characteristic of oxides [17,18].
Moreover, TGA analysis allowed us to establish the temperature of 800 • C as the temperature from which the sample was thermally stabilized.This temperature has been widely used by other authors to obtain catalysts from LDH [12,15,19].

TPR Analysis Results
The reducibility of the calcined LDHs was investigated by TPR measurement; the obtained profiles are shown in Figure 3.The TPR analysis of the different LDHs showed the presence of two peaks depending on whether the sample contained Cu in its composition or not.Thus, the Ni-Cu/LDH and Ni-Fe-Cu/LDH samples both showed one peak above 210 • C (peak I), which was associated to the reduction of bulk CuO [20].
In addition, Figure 3 shows a second peak (II) in the range of 680-800 • C, which was attributed to the reduction of Ni 2+ species in thermally stable phases such as Mg(Ni, Al)O solid solution [12,21].
The addition of precursors reduces the maximum reduction temperature, promoting the reduction of Ni +2 species by weakening the bond between the Ni species and the support [21].In the same way, the substitution of Mg by Ni helps to reduce the NiO-MgO interaction, leading to a decrease in the reduction temperature and a low dispersion of the metals [12].
In this way, Figure 3 shows a displacement of the maximum of peak II with respect to Ni-LDH (797 • C) towards lower temperatures when Fe or Cu was added.Thus, it can be seen how the addition of Fe caused a displacement of the maximum up to 776 • C, while the addition of Cu caused a more pronounced displacement up to 680 • C.This meant that the addition of Cu caused a further weakening of the Ni species in the support.
The total H 2 consumption during TPR analysis of the different calcined LDHs is shown in Table 4.It can be seen that the substitution of 5 mol % of Ni for Fe or Cu proved an increase in H 2 consumption.This increase was more pronounced in the case of Fe.As a result, calcined Ni-Fe-Cu/LDH was the HDL with the highest consumption of H 2 .On the other hand, in order to ensure an adequate reduction of the calcined LDH, we chose a reduction temperature of 900 • C [8] since, as shown in Figure 3, at that temperature there is practically no more consumption of H 2 .

SEM Analysis Results
Figure 4 show SEM micrographs at different magnifications of the as-synthetized Ni-Fe-Cu/LDH.The synthesized LDH showed a homogeneous structure formed by small spheres of about 680 nm in diameter.As seen in Figure 4, as the magnification became larger, it became possible to observe how the synthesized catalyst was formed by small spherical and homogeneous particles, which suggests that the reaction device used was quite suitable in terms of carrying out the synthesis of LDHs.
The determination of the particle diameter was performed using the image analysis program ImageJ, which allowed us to calculate the histogram of the particle size distribution observed by SEM.
The average diameter of the as-synthetized LDH particles observed by SEM was 618.1 nm.After the calcination process, the catalyst lost its hydrotalcite structure, which caused a reduction in size of the particles to 414.2 nm (Figure 5).

XRD Analysis Results
The XRD patterns of as-synthesized, calcined, and hydrogenated Ni-Fe-Cu/LDH are reported in the Figure 6a-c 006), ( 012), (015), ( 018), ( 110), (113), and (116) reflections, respectively.All of them were related to hydrotalcite (JCPDS 22e0700), indicating the formation of a pure hydrotalcite phase.This structure was in agreement with the results obtained by other authors who have studied LDHs [22][23][24].No diffraction peaks were observed for any species of nickel, copper, or iron, which may have been due to their integration into the structure or their high dispersion in the LDH [25].
The smaller the size of the crystalline particles, the more defects they have and the wider the diffraction peaks [26].Therefore, the wide peak (003) indicates the formation of highly crystalline material with a small particle size.
Lattice parameters a and c were calculated following the Equations ( 4)-( 6) and the diffraction angle obtained from the XRD pattern (Figure 6a).Moreover, crystallite size (D) was calculated by Equation ( 7) on the basis of (003) reflections at 11.5 • .These parameters are summarized in Table 5.The values of as-synthesized Ni-Fe-Cu/LDH were similar to those calculated by other authors that have synthesized Ni-based catalyst from LDHs.For example, Zhou et al. [27] synthesized a Ni-Fe/LDH, finding a crystallite size of 9.1 and lattice parameter values of a = 3.06 and c = 23.2.
Lattice parameter c is related to the electrostatic interactions between the brucite-like sheet and the interlayer, and is strongly dependent on the M 2+ /M 3+ ratio that has a value of 3 in the Ni-Fe-Cu/LDH synthetized [16].As as-synthesized Ni-Fe-Cu/LDH was calcined up to 900 • C, and the loss of the hydrotalcite structure progressively took place, resulting in a mixture of metal oxides that can be observed in Figure 6b.As seen in Figure 6b, the XRD pattern for calcined sample showed reflections at around 37 • , 43.5 • , and 62.5 • .These reflections were related to the planes (111), (200), and (220), respectively, which could correspond to the cubic structure of MgO and NiO.Ni 2+ has an ionic radius similar to that of Mg 2+ , and thus it is likely that it was incorporated into the structure, forming the mixed oxide Mg(Ni,Al)O, as described by several authors [22,28,29], without significant modifications in the network parameter.On the other hand, Ni(Fe)O x also has a similar cubic structure to NiO, and thus it is possible that Ni(Fe)O x was also present due to Fe 3+ substitution in the nickel oxide lattice [27].In relation to Cu, no patterns were observed regarding this metal, which may have been because it is highly dispersed or forms an amorphous phase.Table 5 also includes the crystallite size (D) of particles calculated by Equation ( 7) on the basis of (200) reflections and lattice parameters by Equation (8).A reduction of the particle size was obtained after calcination, which improved the characteristics of the catalyst.
After the reduction with H 2 , the reduced Ni-Fe-Cu/LDH was obtained, whose XRD pattern can be seen in Figure 6c.The nickel particles were mostly found as Ni metal, as shown by the reflections at 44.2 • , 51.7 • , and 75.8 • , corresponding to the crystallographic planes (111), (200), and (220).To a lesser extent, NiFe alloy and NiO reflections can also be observed.

Textural Properties Analysis Results
Specific surface area (BET), pore volume, and average pore diameter (BJH) of both as-synthesized and calcined catalysts were obtained, and their results are summarized in Table 6.After calcination, an increase in surface area and pore volume was observed, which may have been due to the removal of carbonate anions in the form of CO 2 as the sample was calcined.Moreover, calcination results in an increase in pore volume and pore diameter, which allowed for improved textural properties of the catalyst.Comparing the textural properties obtained from calcined Ni-Fe-Cu/LDH with respect to commercial catalysts, we could see, for example, that calcined catalyst showed a S BET of 136.70 m 2 g −1 larger than the commercial Raney nickel catalyst that had an average Ni surface area of 100 m 2 g −1 [30].
Figure 7 shows the pore diameter distribution curves of as-synthesized and calcined catalyst, obtained from nitrogen adsorption-desorption isotherm measured at 77 K.For as-synthesized catalyst, we observed that the pore size distribution was very narrow, presenting a very sharp maximum over 3 nm, and most of the pore diameters were between 3 and 10 nm (mesopores).
After calcination of fresh LDH at 800 • C for 4 h, the calcined catalyst showed a wider pore size distribution than as-synthetized catalyst.The most part of the pores were between 3 and 21 nm, with a maximum over 13 nm.This may have been due to the fact that the calcination at high temperatures improved the textural properties, especially in the case where the catalyst contained Fe, as demonstrated by Zhou et al. [27].

Effect of Temperature and S/C Ratio on Catalytic Performance of Ni-Fe-Cu/LDH Catalyst over Steam Reforming of Toluene
The main reactions that take place in the steam reforming of toluene are as follows [15,31,32] Boudouard reaction: Most of the reactions involved in toluene steam reforming are endothermic, and thus the process is favored both thermodynamically and kinetically at high temperatures.
Steam reforming of toluene can occur through reactions ( 12) and ( 13), depending on the amount of water available, producing H 2 , and CO and CO 2, respectively.
Water gas shift (WGS) reaction ( 14) is an equilibrium reaction that is thermodynamically favored at low temperatures and kinetically favored at high temperatures [33].
In addition, toluene can react with CO 2 through the dry reforming reaction (15), forming CO and H 2 , and it also can react through the reaction of hydroalkylation ( 16) with H 2 to produce benzene and methane, although this reaction, because it is exothermic, will be less favorable at high temperatures.On the other hand, benzene can react with H 2 through a hydrocracking reaction (17) to produce methane.Methane in turn can produce CO and H 2 through a steam reforming reaction (19).The Boudouard reaction ( 20) is an exothermic reaction that transforms CO into CO 2 and C.
Finally, it can be observed that in all the reactions except ( 18) and ( 20), there was an increase in the volume from reactants to products, and thus the process was favored at low pressure.

Effect of Temperature on Gas Yield and Gas Composition
Figure 8 shows the conversion of toluene to gases as a function of temperature and S/C ratio.
It can be noticed how as the temperature increased, the conversion increased.At temperatures below 500 • C, the steam reforming reaction did not take place.However, from 500 • C, the conversion increased sharply with temperature until temperature in the range 700-800 • C was reached, where conversion was highest.For temperatures above 800 • C, the conversion remained constant and no longer increased with temperature.The highest conversion (99.87%) was achieved for an S/C of 4 at a temperature of 800 • C.This could have been due to the fact that for higher S/C values, the water could compete for the active centers of the catalyst.Regarding the evolution of CO with temperature (Figure 9a), as the temperature increased, the concentration of CO increased, progressively reaching the maximum value at 900 • C, while the concentration of CO 2 (Figure 9b) increased until reaching its maximum value at 600 • C and then decreased slightly.This development may have been due to the fact that the WGS reaction is an exothermic reaction, and thus as the temperature increased, the equilibrium progressively shifted towards the formation of CO [34].
The concentration of H 2 (Figure 9c) was the largest during steam reforming with toluene.The concentration of hydrogen decreased strongly at temperatures above 500 • C; from this temperature, a slight decrease was observed as the temperature increased.This behavior has been observed by different authors [35] and can be explained again by the endothermic nature of the WGS reverse reaction, which reduces the concentration of H 2 as the temperature increases.
The hydroalkylation (12) and benzene hydrocracking (17) are exothermic reactions and therefore not favored by increasing temperature.As a consequence, the concentration of CH 4 (Figure 9d), after reaching a maximum at 600 • C, decreased sharply with increasing temperature.This means that the concentration of toluene occurred preferably through the reaction (12) as the temperature increased.
In the same way, the formation of benzene (Figure 9e) through reaction ( 16) decreased as the temperature increased due to its exothermic behavior.Benzene yield reached a maximum value at 500 • C of around 8-10%; from this temperature, the concentration of benzene decreased very quickly.This may also have been due to the fact that the catalyst can promote the steam reforming of benzene (18) in the range 600-900 • C.

Effect of S/C Ratio on Gas Yield and Gas Composition
Regarding the influence of the S/C ratio on conversion of toluene to gases (Figure 8), we observed that the maximum differences were reached in the range of temperatures 500-700 • C. The main tendency was that as the S/C ratio increased, the conversion increased up to S/C ratios of 6. S/C values higher than 6 did not encourage an increase in conversion.This fact was especially noticed at 600 • C, where conversions of 56% were reached for S/C values of 1, while for S/C ratios higher than 6, the conversion was higher than 95%.
With respect to the evolution of the concentration of CO (Figure 9a) and CO 2 (Figure 9b), both concentrations were very dependent on the value of S/C.Thus, for example, the concentration of CO was observed to increase when the S/C ratio decreased, and thus the maximum values (17%) were reached for S/C = 1 at 900 • C, while for the same temperature of 900 • C and an S/C = 8, the concentration of CO was around 7%.The evolution of the concentration of CO 2 moved in an inverse way; it increased when the S/C ratio increased, reaching maximum values at S/C = 8.This was evidence that increasing the S/C ratio promotes reaction (13).
In respect to the influence of the S/C ratio on the concentration of H 2 (Figure 9c), the S/C had much less influence than temperature.Moreover, it was possible to observe that at low temperature, the concentration of H 2 decreased as the S/C ratio increased; this effect may have been due to an increase in the basicity.Thus, for example, Ahmed et al. [36] developed a Ni-Fe-Mg/zeolite catalyst and studied its performance in steam reforming reaction of toluene, finding that for S/C ratios higher than 1:1, the amount of H 2 decreased, which they related to a decrease in the basicity of the support.This effect occurred mainly at low temperatures, where the degree of conversion was low in these conditions an increase in the S/C ratio can cause an oxidation of the catalyst.At higher temperatures, there was no clear trend because there was very little variation in the concentration of H 2 with S/C.
The CH 4 concentration (Figure 9d) decreased as the S/C ratio increased, in line with the reaction (19).As shown in Figure 9e, benzene yield was not greatly affected by the S/C ratio; however, as the S/C ratio increased, the amount of benzene generated decreased.

Catalyst Characterization after Reaction
To investigate the characteristics of the catalyst after the steam reforming of toluene, we used an experience using S/C = 4 at 800 • C for 2 h as a reference.
The concentration of the gases remained relatively constant during the development of the test (Figure 10a), reaching an average conversion to gases of 98% (Figure 10b).Throughout the development of the test, no deactivation of the catalyst was observed, and thus the concentration of the gas was quite constant with the following average molar concentration: 76.6% H 2 , 12.1% CO, and 11.3% CO 2 .The results obtained show that the conversion achieved with the developed catalyst allowed us to reach comparable and even higher results to other catalysts on the basis of La or Ce (Table 7).Therefore, the Ni-Fe-Cu/LDH catalyst can be considered as an effective catalyst with a promising toluene conversion capacity.

XRD Analysis Results
The Figure 11 shows the XRD patterns after reduction and after reaction of the catalyst by comparison.
After reduction at 900 • C (Figure 11a), the diffraction lines resulting from the formation of the nickel metal phase and Ni-Fe alloy were observed, together with weaker lines of NiO and MgO.The same lines were observed in the XRD profile after reaction (Figure 11b), but longer and narrower, which meant the formation of larger particles.
In this way, the mean diameter of the Ni particles was calculated by the Scherrer Equation ( 7), using the peak at 2θ = 51.2• , which corresponded to the (200) plane of Ni fcc [31] and lattice parameter by Equation ( 8); all are shown in Table 8.After the reaction, we observed that there was an increase in the size of the Ni particles, which may be attributed to the fact that as the reaction progressed, the sintering of the Ni particles took place.In addition, a slight increase in the lattice parameter took place, which was in line with the fcc structure of the metal nanoparticles, which generally expand with increasing particle size [41].

Amount and Type of Carbon Deposited on the Surface of Catalyst
The amounts of carbon at the end of different tests were analyzed by means of an elemental analyzer.The lowest values were obtained for high temperatures.Thus, for instance, for an S/C = 4 at 800 • C, the amount of carbon deposited after 2 h of reaction was only 1.4 wt %.
In order to determine the influence of the S/C ratio on the amount of carbon deposited, we analyzed the amount of carbon formed at 600 • C for 1 h for different S/C values.The results are shown in Figure 12.
From Figure 12, it can be seen that as the S/C ratio increased, the amount of carbon deposited decreased.For example, when the S/C ratio was 1, the amount of carbon formed was 49.34%, while for an S/C = 2, the amount was drastically reduced to 20.82%.The lowest amount of carbon was obtained by using high S/C ratios of 8.
These amounts of carbon deposited were even less than those detected by other authors; for instance, Josuinkas et al. [31] determined that for a Ni LDH-based catalyst, the amount of carbon deposited was 78.3-83.1 wt % at 800 • C and S/C = 1.5.To identify the type of carbon formed, we carried out an analysis of the TG derivative by means of a TGA analysis.TGA analysis allows us to distinguish between amorphous carbon, which is detected by a peak in the range 450-500 • C, and filamentous carbon, which decomposes in the range 600-650 • C [30].It is well known that amorphous carbon affects the degree of conversion of the catalyst since it blocks the active centers.On the contrary, filamentous carbon affects the conversion to a lesser extent, since it had less serious effect on the deactivation than the amorphous carbon [30].
Figure 13 shows the nature of the carbon deposited on the catalyst over the steam reforming of toluene.Only one peak was appreciated in the thermograms in the range 600-650 • C, which indicates that most of the carbon formed was filamentous, which means it did not affect the activity of the catalyst.
In addition, the effects of the S/C ratio on the amount and type of carbon formed can be observed in Figure 13.Here, the type of carbon formed did not vary with the S/C ratio, being predominantly filamentous carbon in all cases.Moreover, when the S/C ratio increased, the signal of the filamentous carbon decreased, which can be explained by a lower formation of carbon when the amount of water was added.

SEM Analysis of the Catalyst after Reaction
Figure 14 shows the morphological changes of the reduced catalyst (Figure 14a,b) and after 2 h of reaction at 800 • C and S/C of 4 (Figure 14c,d) by scanning electron microscopy.Non-structured carbon was observed in the SEM micrographs after reaction, which confirmed the low content of the carbon analyzed, making it potentially difficult to visualize by SEM.
After reduction of the catalyst, a powder formed by particles with an average diameter of 327 nm was obtained.We observed that the particles of the catalyst were well dispersed and uniformly distributed, but after the reaction, aggregates of smaller particles were formed, resulting in an increase in particle size up to 446 nm.

Conclusions
A study of the behavior of catalyst Ni-Fe-Cu/LDH during the steam reforming of toluene was carried out.The results suggest that for low temperatures at 600 • C, it is necessary to use S/C ratios higher than 6 to achieve gas conversions higher than 90%.On the other hand, at high temperatures above 800 • C, an S/C ratio of 2 was found to be sufficient to achieve high gas conversions.In addition, the use of low S/C ratios allowed for increased concentration of CO.S/C ratio of 4 allowed us to obtain the maximum conversion reached at 800 • C (99.87%) and low values of carbon deposited on the catalyst (1.4 wt %), along with good conversions in the range 600-700 • C above 80% and 90%, respectively.Furthermore, the type of carbon deposited on the catalyst was determined to be mainly filamentous, which, as is known, reduces conversion to a much lesser extent than amorphous carbon.
Moreover, the use of relatively cheap promoters such as Fe and Cu allowed us to obtain a competitive and more affordable catalyst than the catalysts based on expensive metals such as La and Ce.Therefore, the catalyst developed from Ni-Fe-Cu/LDH can be considered as an effective catalyst with a promising toluene conversion capacity, yielding high concentrations of H 2 .

Figure 1 .
Figure 1.Schematic diagram of the experimental system.

Figure 8 .
Figure 8. Conversion of toluene to gases as a function of temperature and S/C ratio.

Figure 10 .
Figure 10.Gas composition (a) and gas conversion (b) during catalytic steam reforming of toluene at 800 • C and S/C = 4.

Figure 12 .
Figure 12.Amount of carbon deposited on the surface of the catalyst during the steam reforming reaction of toluene at 600 • C for different values of the S/C ratio.

Table 2 .
Operating conditions for each steam/carbon molar ratio (S/C ratio) and for W/F = 0.32 g h mol −1 .

Table 3 .
Chemical element analysis of as-synthesized and calcined Ni-Fe-Cu/LDH.

Table 4 .
Total consumption of H 2 .

Table 5 .
Crystallite size and lattice parameters of as-synthesized and calcinated Ni-Fe-Cu/LDH.

Table 6 .
Textural characteristics of the as-synthesized and calcined samples.

Table 7 .
Comparison of the catalytic performances of previously reported catalysts.

Table 8 .
Crystallite size and lattice parameters of Ni particles of Ni-Fe-Cu/LDH after reduction and after reaction.