Life Cycle Assessment and Economic Analysis of an Innovative Biogas Membrane Reformer for Hydrogen Production

This work investigates the environmental and economic performances of a membrane reactor for hydrogen production from raw biogas. Potential benefits of the innovative technology are compared against reference hydrogen production processes based on steam (or autothermal) reforming, water gas shift reactors and a pressure swing adsorption unit. Both biogas produced by landfill and anaerobic digestion are considered to evaluate the impact of biogas composition. Starting from the thermodynamic results, the environmental analysis is carried out using environmental Life cycle assessment (LCA). Results show that the adoption of the membrane reactor increases the system efficiency by more than 20 percentage points with respect to the reference cases. LCA analysis shows that the innovative BIONICO system performs better than reference systems when biogas becomes a limiting factor for hydrogen production to satisfy market demand, as a higher biogas conversion efficiency can potentially substitute more hydrogen produced by fossil fuels (natural gas). However, when biogas is not a limiting factor for hydrogen production, the innovative system can perform either similar or worse than reference systems, as in this case impacts are largely dominated by grid electric energy demand and component use rather than conversion efficiency. Focusing on the economic results, hydrogen production cost shows lower value with respect to the reference cases (4 €/kgH2 vs 4.2 €/kgH2) at the same hydrogen delivery pressure of 20 bar. Between landfill and anaerobic digestion cases, the latter has the lower costs as a consequence of the higher methane content.


Introduction
Hydrogen is a promising energy carrier, that can replace fossil fuels in power generation and transports, when produced by renewable sources [1].Nowadays H 2 production mainly comes from steam reforming of natural gas [2], although H 2 can be produced from others fossil sources by hydrocarbon reforming and pyrolysis of coal or natural gas, or from renewable feedstocks by biological or thermochemical processing of biomass or water splitting [3].In Europe, the common biogas (BG) production process is the anaerobic digestion of agricultural waste, manure, and energy crops; then biogas, or biomethane (if the plant has an upgrading step) is currently fed to an internal combustion engine for electricity and heat production [4].The Fuel Cells and Hydrogen Joint Undertaking (FCH-JU) project BIONICO, financed by the European Commission, aims at developing an innovative concept for green hydrogen production from raw biogas.Steam reforming of raw biogas, that mainly consists of methane and carbon dioxide, was identified as one of the cheapest and promising way for hydrogen production [1].
As shown in Figure 1, the conventional reforming process consists of a steam reformer (SMR) or autothermal reformer (ATR), typically working at 800 • C, followed by two water gas shift (WGS) reactors (high-temperature, HT-WGS, and low-temperature, LT-WGS) and by a pressure swing adsorption (PSA) unit for hydrogen separation [5].The innovative membrane reactor technology, such as the autothermal catalytic membrane reactor (ATR-CMR) in Figure 1, developed within BIONICO, allows the production and separation of hydrogen in a single vessel, with advantages over traditional biogas reforming related to the increase of the overall conversion efficiency and to the strong decrease of equipment size due to the process intensification [6].
biogas, that mainly consists of methane and carbon dioxide, was identified as one of the cheapest and promising way for hydrogen production [1].
As shown in Figure 1, the conventional reforming process consists of a steam reformer (SMR) or autothermal reformer (ATR), typically working at 800 °C, followed by two water gas shift (WGS) reactors (high-temperature, HT-WGS, and low-temperature, LT-WGS) and by a pressure swing adsorption (PSA) unit for hydrogen separation [5].The innovative membrane reactor technology, such as the autothermal catalytic membrane reactor (ATR-CMR) in Figure 1, developed within BIONICO, allows the production and separation of hydrogen in a single vessel, with advantages over traditional biogas reforming related to the increase of the overall conversion efficiency and to the strong decrease of equipment size due to the process intensification [6].
Compared to previous works [7,8], this paper starts from the energy and economic consideration to evaluate the environmental performance of the innovative BIONICO process comparing results with the conventional H2 production processes from raw biogas assumed as references.The combination of conventional techno-economic assessment with environmental assessment is necessary when dealing with technologies aiming at increasing the overall system efficiency, reducing the energy consumption.Life cycle assessment (LCA) determines the environmental impacts including all the system aspects, covering multiple indicators, including water withdrawal, ecosystems, resources depletion, and human health, with detailed analysis on the climate change impact.Various LCA studies have been performed on biogas production system and its conversion into combined electricity and heat (CHP), and they all provide quite similar insights.Whting et al. [9] showed that the global warming potentials (GWP) of a CHP system fed with biogas from anaerobic digestion of agricultural wastes can be much lower compared with fossil fuel alternatives: in particular, climate change impacts are influenced by the type and source of feedstock, digestate storage and its application on land.Bacenetti et al. [10] found that feedstock production and digestate emissions are the main contributors to the impact of agricultural anaerobic digestion plants.Van Stappen et al. [11] identified that the key determining factors for LCA are the choices of biogas feedstock and displaced marginal technologies for electricity production and fertilizers.Hijazi et al. [12] reviewed the LCA study of biogas production in Europe, and also found sources of feedstocks for biogas determining the overall environmental impact for biogas systems.Moreover, some LCA studies have also been performed on hydrogen production from biogas.Hajjaji et al. [13] found a cradle to grave carbon footprint of 5.59 kgCO2-eq per kg of H2 produced from biogas from anaerobic digesters.More than 96% of those impact came from the biogas feedstock production stage, and impact results are highly influenced by the amount of artificial fertilizer displaced by digestate and credits from recycling the plant construction materials and equipment.Valente et al., [14] calculated the harmonized carbon footprint from 71 case studies of green H2 production: the only case study related to biogas reforming [13] resulted in a harmonized carbon footprint is 7.34 kgCO2-eq per kg of H2 produced.Battista et al., [15] investigated an ATR reforming process finding that the carbon ATR-CM R (500-550°C)

SR or ATR
(800°C) Compared to previous works [7,8], this paper starts from the energy and economic consideration to evaluate the environmental performance of the innovative BIONICO process comparing results with the conventional H 2 production processes from raw biogas assumed as references.The combination of conventional techno-economic assessment with environmental assessment is necessary when dealing with technologies aiming at increasing the overall system efficiency, reducing the energy consumption.Life cycle assessment (LCA) determines the environmental impacts including all the system aspects, covering multiple indicators, including water withdrawal, ecosystems, resources depletion, and human health, with detailed analysis on the climate change impact.

Conventional process I nnovative process
Various LCA studies have been performed on biogas production system and its conversion into combined electricity and heat (CHP), and they all provide quite similar insights.Whting et al. [9] showed that the global warming potentials (GWP) of a CHP system fed with biogas from anaerobic digestion of agricultural wastes can be much lower compared with fossil fuel alternatives: in particular, climate change impacts are influenced by the type and source of feedstock, digestate storage and its application on land.Bacenetti et al. [10] found that feedstock production and digestate emissions are the main contributors to the impact of agricultural anaerobic digestion plants.Van Stappen et al. [11] identified that the key determining factors for LCA are the choices of biogas feedstock and displaced marginal technologies for electricity production and fertilizers.Hijazi et al. [12] reviewed the LCA study of biogas production in Europe, and also found sources of feedstocks for biogas determining the overall environmental impact for biogas systems.Moreover, some LCA studies have also been performed on hydrogen production from biogas.Hajjaji et al. [13] found a cradle to grave carbon footprint of 5.59 kg CO2-eq per kg of H 2 produced from biogas from anaerobic digesters.More than 96% of those impact came from the biogas feedstock production stage, and impact results are highly influenced by the amount of artificial fertilizer displaced by digestate and credits from recycling the plant construction materials and equipment.Valente et al., [14] calculated the harmonized carbon footprint from 71 case studies of green H 2 production: the only case study related to biogas reforming [13] resulted in a harmonized carbon footprint is 7.34 kg CO2-eq per kg of H 2 produced.Battista et al., [15] investigated Processes 2019, 7, 86 3 of 14 an ATR reforming process finding that the carbon footprint from required material production and the total life cycle stages are 0.08 and 7.24 kg CO2-eq per kg of H 2 produced respectively.Major impacts are related to energy consumption of the PSA and air compressors as well as CO 2 emitted during the auto-thermal reforming process.
Most of the above studies focus on answering the question: "what are the environmental impacts attributed to producing biogas or its derivative product?"Furthermore, they also identified the hotspots influencing impacts are the sourcing of substrates and digestate storage.Admittedly, the biogas production stage is important, however, it is less relevant to our question.In this study, our question is different.The focus is not to debate if we should produce biogas, nor what feedstock of substrates or digestate storage options should be chosen.Instead, the reference condition in this study considers the existing biogas from waste substrates that have been or will be managed for energy production or simply flared without energy recovery.From this reference point, the purpose of our study is to answer the following question: "What technologies are preferable for the environment by diverting the biogas mentioned above for producing hydrogen?" This study aims to provide a techno-economic and environmental life cycle assessment of the ATR-CMR technology and of the reference technology under different configurations (SMR or ATR) and operating conditions.

Case Studies
Six case studies, that differ in terms of production process and biogas composition, are investigated.The innovative BIONICO system is compared with two conventional fuel processor (SMR and ATR); on the other hand, two raw biogas compositions biogases produced by landfill (LF) and anaerobic digestion (AD) are considered.All three systems are designed to produce 100 kg/day of pure hydrogen.Moreover, this work sets a pressure delivery of 20 bar in order to compare the system efficiency with the conventional plants (an additional hydrogen compressor is introduced since hydrogen stream is produced at ambient pressure).As shown in Table 1, the main biogas differences lie on CH 4 and inert (CO 2 , N 2 ) content.

System Layouts
Figure 2 shows layouts for both a conventional system based on steam reforming (Figure 2 left) or auto-thermal reforming (Figure 2 right), while the innovative plant with auto-thermal membrane reactor and vacuum pump is represented in Figure 3.In the first reference layout (Figure 2, left), a mixture of compressed BG and steam is fed to the SMR reactor.After a first cooling step (HX-4), the syngas exiting the reforming reactor is sent to water gas shift reactors to promote the CO conversion in CO2, increasing hydrogen production.The resulting stream consists of a H2 rich syngas diluted with inert gases that, after the water removal, is sent to a pressure swing adsorption unit to recover a pure H2 flow.The heat required by the endothermic reaction at the SMR is supplied by the combustion of the PSA off-gas together with an additional amount of biogas (BGbrn).Regarding the second reference layout (Figure 2, right), the main difference with the previous case relies on the main reactor for biogas to hydrogen conversion.The stream at the inlet of the reactor is a mixture of compressed BG, steam and air.In fact, the heat required by the endothermic reforming reaction is balanced by the partial oxidation of the feed fuel with air.The intake of air is always below stoichiometry and it is regulated to control the reactor operating temperature.Thanks to the partial oxidation, there is no need to supply an additional amount of biogas to the burner: in the ATR configuration, the burner is fed only with the off-gas from the PSA.In the first reference layout (Figure 2, left), a mixture of compressed BG and steam is fed to the SMR reactor.After a first cooling step (HX-4), the syngas exiting the reforming reactor is sent to water gas shift reactors to promote the CO conversion in CO2, increasing hydrogen production.The resulting stream consists of a H2 rich syngas diluted with inert gases that, after the water removal, is sent to a pressure swing adsorption unit to recover a pure H2 flow.The heat required by the endothermic reaction at the SMR is supplied by the combustion of the PSA off-gas together with an additional amount of biogas (BGbrn).Regarding the second reference layout (Figure 2, right), the main difference with the previous case relies on the main reactor for biogas to hydrogen conversion.The stream at the inlet of the reactor is a mixture of compressed BG, steam and air.In fact, the heat required by the endothermic reforming reaction is balanced by the partial oxidation of the feed fuel with air.The intake of air is always below stoichiometry and it is regulated to control the reactor operating temperature.Thanks to the partial oxidation, there is no need to supply an additional amount of biogas to the burner: in the ATR configuration, the burner is fed only with the off-gas from the PSA.In the first reference layout (Figure 2, left), a mixture of compressed BG and steam is fed to the SMR reactor.After a first cooling step (HX-4), the syngas exiting the reforming reactor is sent to water gas shift reactors to promote the CO conversion in CO 2 , increasing hydrogen production.The resulting stream consists of a H 2 rich syngas diluted with inert gases that, after the water removal, is sent to a pressure swing adsorption unit to recover a pure H 2 flow.The heat required by the endothermic reaction at the SMR is supplied by the combustion of the PSA off-gas together with an additional amount of biogas (BG brn ).Regarding the second reference layout (Figure 2, right), the main difference with the previous case relies on the main reactor for biogas to hydrogen conversion.The stream at the inlet of the reactor is a mixture of compressed BG, steam and air.In fact, the heat required by the endothermic reforming reaction is balanced by the partial oxidation of the feed fuel with air.The intake of air is always below stoichiometry and it is regulated to control the reactor operating temperature.Thanks to the partial oxidation, there is no need to supply an additional amount of biogas to the burner: in the ATR configuration, the burner is fed only with the off-gas from the PSA.
In the BIONICO layout (Figure 2, right), the BG is firstly compressed (CMP BG ), then preheated up to 300 • C in HX-4 and mixed with steam and water at the inlet of the ATR-CMR.At the ATR-CMR outlet, two streams, the retentate and the pure H 2 , leave from the top section of the reactor.The retentate stream, which mainly consists of steam, CO 2 and N 2 with the remaining CO, CH 4 and H 2 is cooled down to 200 • C and throttled before being combusted in air.The separated hydrogen is cooled down to 30 • C and then compressed to the delivery pressure by the vacuum pump/hydrogen compressor.The amount of hydrogen separated in the ATR-CMR is determined so that the thermal power of the retentate closes the energy balance of the system avoiding additional BG supply.

Techno-Economic Results
The innovative fuel processor and the conventional systems, together with their relative balance of plant, are implemented in Aspen Plus ® (AspenTech, Bedford, Massachusetts, MA, USA) [16], where mass and energy balances are solved.The methodology adopted is consistent with previous works [8,17].A phenomenological model of membrane reactor developed in Aspen Custom Modeler®(ACM) was adopted [18].The scheme of the membrane reactor model and the main membrane features are summarised respectively in Figure A1 and Table A1 in the Appendix A section.
All the cases are compared in terms of overall system efficiency, defined in Equation ( 1) as the ratio of H 2 energy output to biogas and auxiliaries' energy inputs: where LHV H2 is equal to 120 MJ/kg [19]; W aux is the sum of the electric consumptions of the system auxiliaries (i.e., compressors, pumps, control system); η el,ref is set equal to 45% as the average electric efficiency of the power generating park [20].
The main design parameters for the investigated systems are listed in Table 2.A sensibility analysis on reactors operating conditions (p, T and steam to carbon S/C), and reactor geometry for the innovative ATR-CMR solution produced more than 400 simulations.Table 3 summarizes the thermodynamic and economic results for the two biogas compositions with the highest efficiency [7,8].The overall system efficiency for the BIONICO system is higher than 65% which is at least 19 and 41 percentage points higher than SMR and ATR cases.
Starting from the thermodynamic results, a preliminary economic analysis of the BIONICO system is carried out to compare the cost of produced hydrogen at different operating conditions.Results are also compared with values found for conventional hydrogen production systems from [7].The total plant cost (TPC) is calculated with a bottom-up approach breaking down the power plant into basic components or equipment, and then adding installation costs, indirect costs and owner's and contingencies costs [21].The components costs, obtained from literature, quotes and reports are then scaled and actualized with the CEPCI index.To evaluate the final levelized cost of hydrogen (LCOH), consumables, auxiliaries variable and fixed costs are added to the TPC, according to the following formulation: where CCF represents the carrying charge factor [21] and M H2 is the amount of hydrogen produced in one year of operation.The total installation costs were taken equal to 65% and 80% of the total equipment cost for the innovative and conventional systems respectively [22,23].Fixed operation and maintenance (O & M) costs are represented by maintenance, insurance and operators costs, while variable O&M costs consider consumables such as catalyst, biogas [24], process water, membranes and auxiliaries electric energy consumptions [25].Palladium membranes on ceramic supports cost is retrieved from the FERRET project [26] and refers to a production at a semi-industrial scale: membrane cost is included both in the capital cost and in the O & M variable costs taking into account a lifetime of 5 years.The complete methodology and the detailed components costs are reported in [7,8].Regarding the economic analysis, hydrogen production cost shows lower value respect to the reference cases (4 €/kg H2 vs 4.2 €/kg H2 ) at the same hydrogen delivery pressure of 20 bar.Between landfill and anaerobic digestion cases, the latter has the lower costs as consequence of the higher methane content.

Lifecycle Assessment (LCA) Methodology
The life cycle assessment approach considered the standards, ISO 14040 [27] and ISO 14044 [28], and the FC-Hy guide for performing LCAs on hydrogen technologies [29].The functional unit is defined as providing 1 kg of H 2 (LHV = 120 MJ/kg) at 20 bar, 15 • C and 99.99% of purity to satisfy the hydrogen market demand.The system boundary is shown in Figure 4 where BIONICO hydrogen production technology is compared to the conventional systems.The biogas production process and the H 2 storage, delivery and use are excluded, being equivalent for all the systems.
This study considered the impact of the H 2 production system on the current biogas availability and utilization where nowadays biogas is fed to an internal combustion engine producing electric and thermal energy.Two LCA scenarios are developed: 1.
Biogas availability for H 2 production is limited.Under this scenario, a system with a higher biogas conversion efficiency (i.e., BIONICO process) can supply more H 2 to the market.Choosing a technology with lower efficiency means it will require a certain amount of H 2 produced from conventional process (such as natural gas steam reforming) to meet the same demand, as shown in Figure 5.

2.
Biogas production is abundant, thus there is a surplus of biogas which is simply flared.In this scenario, biogas utilization is not competing with other potential uses.For the foreground life cycle inventory data, biogas electricity and auxiliary inputs (water, air) required for the H2 production stages are based on the techno-economic modelling data.Component data (including reactors, catalyst, membrane) are collected from partners and also data from a previous European project related to H2 production [30].The life cycle inventory also includes the components that have been affected by diverting biogas flux for H2 production: it starts from potential loss of electric and thermal energy that could be produced by the diverted biogas, to the additional impact occurred during the H2 production stages.Furthermore, the following key assumptions are taken into account:    For the foreground life cycle inventory data, biogas electricity and auxiliary inputs (water, air) required for the H2 production stages are based on the techno-economic modelling data.Component data (including reactors, catalyst, membrane) are collected from partners and also data from a previous European project related to H2 production [30].The life cycle inventory also includes the components that have been affected by diverting biogas flux for H2 production: it starts from potential loss of electric and thermal energy that could be produced by the diverted biogas, to the additional impact occurred during the H2 production stages.Furthermore, the following key assumptions are taken into account:  For the foreground life cycle inventory data, biogas electricity and auxiliary inputs (water, air) required for the H 2 production stages are based on the techno-economic modelling data.Component data (including reactors, catalyst, membrane) are collected from partners and also data from a previous European project related to H 2 production [30].The life cycle inventory also includes the components that have been affected by diverting biogas flux for H 2 production: it starts from potential loss of electric and thermal energy that could be produced by the diverted biogas, to the additional impact occurred during the H 2 production stages.Furthermore, the following key assumptions are taken into account:

•
For scenario 1, the energy recovery of biogas is assumed to be cogeneration of electricity and heat.The electric and heat efficiencies are assumed to be 39% and 46%, respectively, with a total CHP efficiency of 85% [31].The impact of biogas production is excluded from the cogeneration impact.The marginal replacing technology for the lost energy resulting from biogas diversion are assumed to be the European average for electricity generation and natural gas cogeneration for heat production;

•
The European average grid mix is assumed to be the marginal electricity generation technology demanded for hydrogen production;

•
The only relevant air emission during the H 2 production process is CO 2 , which is considered to be carbon neutral in this study; • When natural gas is used as additional feedstock for H 2 production, it is assumed the conventional H 2 production from the steam reforming technology is used.The inventory and impact data are based on [30,32].
The secondary life cycle impact (LCI) data, describing background processes (e.g., transportation, electricity production), comes from the Ecoinvent database v3.4 (Ecoinvent, Zurich, Switzerland) [33].Besides climate change, the analysis will be focused on human health, ecosystem quality and resources as endpoints.

Results and Discussion
Figure 6 (left) illustrates the climate change impact of the scenario 1 when biogas is a limiting factor.BIONICO ATR-CMR technology performs better than reference systems (SR or ATR), thanks to its higher efficiency of converting biogas to H 2 .The carbon footprint of the CMR technology could be 45-46% lower than the conventional hydrogen production metho3333d using steam reforming of fossil natural gas.In this scenario, the impact due to the electrical and thermal energy production loss (biogas is not feeding a cogeneration system) is equivalent for all scenario as the maximum amount of biogas for the conventional process is fixed.As shown in Figure 7 (left), the total thermal input of the BIONICO system is always lower respect to the other processes thanks to the reduced amount of biogas, while the electric consumption is really high only for the ATR case.The key factors are the carbon footprint of the electricity input and of the additional demand for H 2 using fossil natural gas feedstock from lower biogas conversion efficiency systems, as represented in Figure 7 (right).

•
For scenario 1, the energy recovery of biogas is assumed to be cogeneration of electricity and heat.The electric and heat efficiencies are assumed to be 39% and 46%, respectively, with a total CHP efficiency of 85% [31].The impact of biogas production is excluded from the cogeneration impact.The marginal replacing technology for the lost energy resulting from biogas diversion are assumed to be the European average for electricity generation and natural gas cogeneration for heat production;

•
The European average grid mix is assumed to be the marginal electricity generation technology demanded for hydrogen production; The only relevant air emission during the H2 production process is CO2, which is considered to be carbon neutral in this study; • When natural gas is used as additional feedstock for H2 production, it is assumed the conventional H2 production from the steam reforming technology is used.The inventory and impact data are based on [32] and [30].
The secondary life cycle impact (LCI) data, describing background processes (e.g., transportation, electricity production), comes from the Ecoinvent database v3.4 (Ecoinvent, Zurich, Switzerland) [33].Besides climate change, the analysis will be focused on human health, ecosystem quality and resources as endpoints.

Results and Discussion
Figure 6 (left) illustrates the climate change impact of the scenario 1 when biogas is a limiting factor.BIONICO ATR-CMR technology performs better than reference systems (SR or ATR), thanks to its higher efficiency of converting biogas to H2.The carbon footprint of the CMR technology could be 45-46% lower than the conventional hydrogen production metho3333d using steam reforming of fossil natural gas.In this scenario, the impact due to the electrical and thermal energy production loss (biogas is not feeding a cogeneration system) is equivalent for all scenario as the maximum amount of biogas for the conventional process is fixed.As shown in Figure 7 (left), the total thermal input of the BIONICO system is always lower respect to the other processes thanks to the reduced amount of biogas, while the electric consumption is really high only for the ATR case.The key factors are the carbon footprint of the electricity input and of the additional demand for H2 using fossil natural gas feedstock from lower biogas conversion efficiency systems, as represented in Figure 7 (right).On the other hand, when biogas is not a limiting factor (scenario 2), the use of higher or lower amount of biogas does not cause additional impacts, thus the energy production loss is zero.Figure 6 (right) shows that climate change impact is dominated by the amount of electricity input required from the grid, as the principle source for hydrogen production.The carbon footprint of both CMR or SMR technology are quite similar as can be seen from the electric auxiliary consumptions in Figure 8 and Table 3: both the systems can achieve large carbon footprint reduction compared to the ATR system and the conventional H2 production.On the other hand, when biogas is not a limiting factor (scenario 2), the use of higher or lower amount of biogas does not cause additional impacts, thus the energy production loss is zero.Figure 6 (right) shows that climate change impact is dominated by the amount of electricity input required from the grid, as the principle source for hydrogen production.The carbon footprint of both CMR or SMR technology are quite similar as can be seen from the electric auxiliary consumptions in Figure 8 and Table 3: both the systems can achieve large carbon footprint reduction compared to the ATR system and the conventional H 2 production.
Processes 2019, 7, 86 9 of 14 On the other hand, when biogas is not a limiting factor (scenario 2), the use of higher or lower amount of biogas does not cause additional impacts, thus the energy production loss is zero.Figure 6 (right) shows that climate change impact is dominated by the amount of electricity input required from the grid, as the principle source for hydrogen production.The carbon footprint of both CMR or SMR technology are quite similar as can be seen from the electric auxiliary consumptions in Figure 8 and Table 3: both the systems can achieve large carbon footprint reduction compared to the ATR system and the conventional H2 production.Lastly, Figure 9 compared the climate change impact of the two investigated scenarios with respect to the levelized cost of hydrogen confirming that ATR system has the highest impact both from economic and environmental point of view while conventional SR process is similar to the BIONICO technology just in the second scenario where biogas availability is not a constraint.
The results of the other environmental factors are shown in Figure 10, where both SMR and CMR technology performs better than ATR; however, the difference between SMR and BIONICO ATR-CMR systems is not significant due to the uncertainties associated with the impact modelling.Process contribution analysis indicates that, for all scenarios, all endpoint categories are highly influenced by the required electricity input and its impact for hydrogen production.For Scenario 1 specifically, the impacts are also influenced by the lost credits of electricity and heat generation due to biogas diversion and also by the additional natural gas required as feedstock to meet H 2 demand by systems with lower biogas conversion efficiency.The results also show a higher overall energy conversion efficiency does not necessarily lead to better human health and ecosystems.A trade-off of climate change and other impact categories should always be investigated.Lastly, Figure 9 compared the climate change impact of the two investigated scenarios with respect to the levelized cost of hydrogen confirming that ATR system has the highest impact both from economic and environmental point of view while conventional SR process is similar to the BIONICO technology just in the second scenario where biogas availability is not a constraint.
The results of the other environmental factors are shown in Figure 10, where both SMR and CMR technology performs better than ATR; however, the difference between SMR and BIONICO ATR-CMR systems is not significant due to the uncertainties associated with the impact modelling.Process contribution analysis indicates that, for all scenarios, all endpoint categories are highly influenced by the required electricity input and its impact for hydrogen production.For Scenario 1 specifically, the impacts are also influenced by the lost credits of electricity and heat generation due to biogas diversion and also by the additional natural gas required as feedstock to meet H2 demand by systems with lower biogas conversion efficiency.The results also show a higher overall energy conversion efficiency does not necessarily lead to better human health and ecosystems.A trade-off of climate change and other impact categories should always be investigated.

Conclusions
This work investigates the environmental and economic performances of an innovative membrane reformer for hydrogen production from raw biogas.The introduction of palladium membranes in a reforming reactor allows ther simultaneous hydrogen production and separation.This concept has been developed within the BIONICO project.The performance of the BIONICO concept is compared against two available technologies based on reforming, water gas shift reactors and pressure swing adsorption for hydrogen purification.Lastly, Figure 9 compared the climate change impact of the two investigated scenarios with respect to the levelized cost of hydrogen confirming that ATR system has the highest impact both from economic and environmental point of view while conventional SR process is similar to the BIONICO technology just in the second scenario where biogas availability is not a constraint.

SMR ATR CMR LF AD
The results of the other environmental factors are shown in Figure 10, where both SMR and CMR technology performs better than ATR; however, the difference between SMR and BIONICO ATR-CMR systems is not significant due to the uncertainties associated with the impact modelling.Process contribution analysis indicates that, for all scenarios, all endpoint categories are highly influenced by the required electricity input and its impact for hydrogen production.For Scenario 1 specifically, the impacts are also influenced by the lost credits of electricity and heat generation due to biogas diversion and also by the additional natural gas required as feedstock to meet H2 demand by systems with lower biogas conversion efficiency.The results also show a higher overall energy conversion efficiency does not necessarily lead to better human health and ecosystems.A trade-off of climate change and other impact categories should always be investigated.

Conclusions
This work investigates the environmental and economic performances of an innovative membrane reformer for hydrogen production from raw biogas.The introduction of palladium membranes in a reforming reactor allows ther simultaneous hydrogen production and separation.This concept has been developed within the BIONICO project.The performance of the BIONICO concept is compared against two available technologies based on reforming, water gas shift reactors and pressure swing adsorption for hydrogen purification.

Conclusions
This work investigates the environmental and economic performances of an innovative membrane reformer for hydrogen production from raw biogas.The introduction of palladium membranes in a reforming reactor allows ther simultaneous hydrogen production and separation.This concept has been developed within the BIONICO project.The performance of the BIONICO concept is compared against two available technologies based on reforming, water gas shift reactors and pressure swing adsorption for hydrogen purification.
The system simulations performed with Aspen considered two different biogas compositions, one from landfill and one from anaerobic digestion.The BIONICO system outperforms the reference cases by 40-50% points achieving a hydrogen production efficiency around 69% assuming a delivery pressure of 20 bara.Afterwards, the economic assessment for the investigated cases was carried out accounting for both the capital and operating costs to determine the hydrogen production costs.The hydrogen cost production of the BIONICO case ranges from 4 to 4.2 €/kg H2 , while the reference case resulted 4.21 €/kg H2 and 6.4 €/kg H2 for the SMR and ATR respectively.With respect to the steam reforming reference case, the BIONICO one has lower biogas and capital costs, but higher electricity costs (as a consequence of the hydrogen compression consumptions), while it has lower biogas and electricity cost with respect to the ATR case.Between the landfill and anaerobic digestion cases, the latter has the lower costs as a consequence of the higher methane content and same price assumed.These results outline the fact that membrane reactors are a promising technology for green hydrogen production starting from biogas.
For environmental life cycle assessment, this shows that the BIONICO case performs better than reference systems for climate change and resource indicators, when biogas becomes a limiting factor for H 2 production to satisfy market demand, as the results are more influenced by the additional hydrogen production.For a healthy human ecosystem, the results are more influenced by the amount and environmental profile of direct electricity input.However, when biogas is not a limiting factor for H 2 production, the innovative system can perform either similarly or worse than reference systems, as impacts are dominated by grid electric energy demand.This study highlights the technology deployment should be carefully examined considering local reference conditions, and type and efficiency of displaced or required marginal technologies for electricity production.
(vacuum or co-counter flow sweep gas, including gas diffusion limitations in the porous support) [18].Membrane reactor bed is divided into three main regions, which lengths can be set by the user: the first region at the bottom of the reactor is dedicated to the oxidation and reforming reactions, the middle region is occupied by the membranes (permeation zone); the last section is a buffer region that mainly corresponds with the free-board region.The schematic of Aspen Custom Modeler fluidized bed membrane reactor model is depicted in Figure A1 while the main features of reactor design are reported in Table A1.

Membrane Reactor
The membrane reactor model includes reforming reactions (different kinetic schemes or chemical equilibrium), detailed hydrodynamics of bubble-emulsion phases and different options on the permeate side (vacuum or co-counter flow sweep gas, including gas diffusion limitations in the porous support) [18].Membrane reactor bed is divided into three main regions, which lengths can be set by the user: the first region at the bottom of the reactor is dedicated to the oxidation and reforming reactions, the middle region is occupied by the membranes (permeation zone); the last section is a buffer region that mainly corresponds with the free-board region.The schematic of Aspen Custom Modeler fluidized bed membrane reactor model is depicted in Figure A1 while the main features of reactor design are reported in Table A1.Membranes consist of a Pd-Ag layer deposited onto a ceramic multilayer porous support.Parameters of the permeation law (pre-exponential factor k0, apparent activation energy Ea and exponential factor n), listed in Table 4, comes from experimental analysis of [34].Membranes consist of a Pd-Ag layer deposited onto a ceramic multilayer porous support.Parameters of permeation law (pre-exponential factor k 0 , apparent activation energy Ea and exponential factor n), listed in Table 2, comes from experimental analysis of [34].

Figure 4 .
Figure 4. System boundaries for the reference technologies (SMR and ATR) and BIONICO ATR-CMR technology.

Figure 5 .
Figure 5. Scenario 1: biogas utilization and H2 production from the different systems.

Figure 4 .
Figure 4. System boundaries for the reference technologies (SMR and ATR) and BIONICO ATR-CMR technology.

Figure 4 .
Figure 4. System boundaries for the reference technologies (SMR and ATR) and BIONICO ATR-CMR technology.

Figure 5 .
Figure 5. Scenario 1: biogas utilization and H2 production from the different systems.

Figure 5 .
Figure 5. Scenario 1: biogas utilization and H 2 production from the different systems.

Figure 6 .
Figure 6.Climate change impact of the investigated systems against the conventional H2 production from natural gas steam reforming. 0

Figure 6 .
Figure 6.Climate change impact of the investigated systems against the conventional H 2 production from natural gas steam reforming.

Figure 7 .
Figure 7. Scenario 1 results: thermal power inputs (electric auxiliary and require biogas) for the three H2 production systems (left) and climate change impact of H2 production from biogas and fossil fuel (right).

Figure 8 .Figure 7 .
Figure 8. Scenario 2 results: climate change impact as a function of the auxiliary electric consumptions for the three investigated systems.

Figure 7 .
Figure 7. Scenario 1 results: thermal power inputs (electric auxiliary and require biogas) for the three H2 production systems (left) and climate change impact of H2 production from biogas and fossil fuel (right).

Figure 8 .Figure 8 .
Figure 8. Scenario 2 results: climate change impact as a function of the auxiliary electric consumptions for the three investigated systems.

Processes 2019, 7 , 86 10 of 14 Figure 9 .
Figure 9.Comparison of the climate change impact of both scenario 1 (left) and scenario 2 (right) with respect to the cost of hydrogen.

Figure 10 .
Figure 10.Comparison of endpoint environmental impact of different systems under different scenarios.

Figure 9 .
Figure 9.Comparison of the climate change impact of both scenario 1 (left) and scenario 2 (right) with respect to the cost of hydrogen.

Figure 9 .
Figure 9.Comparison of the climate change impact of both scenario 1 (left) and scenario 2 (right) with respect to the cost of hydrogen.

Figure 10 .
Figure 10.Comparison of endpoint environmental impact of different systems under different scenarios.

Figure 10 .
Figure 10.Comparison of endpoint environmental impact of different systems under different scenarios.

Figure A1 .
Figure A1.Scheme of fluidized bed membrane reactor developed in ACM for vacuum pump and sweep gas case.

Figure A1 .
Figure A1.Scheme of fluidized bed membrane reactor developed in ACM for vacuum pump and sweep gas case.

Table 3 .
Techno-economic results for reference and innovative BIONICO systems.