Green Plasticizer for Poly(vinyl chloride) Re-Granulate Production: Case Study of Sustainability Concept Implementation

: The increase in waste polymer recycling has helped in promoting sustainability, and together with the use of renewable raw materials, it has become a widespread concept with positive effects on both the economy and ecology. Accordingly, the aim of this study was the synthesis of “green” plasticizers, marked as LA/PG/PET/EG/LA, formed from waste poly(ethylene terephthalate) (PET) and bio-based platform chemicals propylene glycol (PG) and levulinic acid (LA). The structure of the obtained plasticizers was complex, as confirmed by results from nuclear magnetic resonance (NMR) and Fourier-transform infrared spectroscopy (FTIR) analysis. The LA/PG/PET/EG/LA plasticizers and waste poly(vinyl chloride) (PVC) were used in an optimized technology for PVC re-granulate production. The hardness of the PVC-based material with “green” plasticizers, in comparison to commercial plasticizer dioctyl terephthalate (DOTP), increased by 11.3%, while migration decreased. An improved material homogeneity and wettability of the fibers by the matrix were observed using SEM analysis of the material’s fracture surface, with a higher efficiency of intermolecular interactions leading to better mechanical performances of the newly designed materials. Thus, LA/PG/PET/EG/LA are unique materials with good compounding and plasticizing potential for PVC, as revealed by differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). In that manner, the use of bio-renewable resources and recycled polymers will contribute to diminishing waste polymer generation, contributing to a lower carbon footprint.


Introduction
Fossil-based polymers, due to their economic significance, are extensively used globally in diverse product forms and areas of application.The importance of recycling waste polymers is increasing, emphasizing the pronounced growth of polymer consumption.The projection for the year 2050 estimates that a staggering amount of over 12,000 million metric tons of plastic waste will accumulate in landfills or the environment, highlighting the urgency of resolving this issue [1].Plastic waste, which is composed of non-biodegradable polymers and often contains different additives, mostly derived from petrochemical resources, presents a notable environmental threat when not appropriately managed.In response to increasing environmental pollution, efforts are being made to establish a circular economy, a concept that involves the implementation of sustainable practices to reduce and promote the recycling of waste materials [2].This is prompted by growing environmental and economic concerns, as well as the recognition of limited fossil resources [3].Such a concept is based on the creation of a closed-loop system where materials are recycled, minimizing the environmental impact and fostering a more sustainable and responsible approach to waste and renewable resource management, leading to a lower dependence on petroleum-based components.Among commercial polymers, belonging to either thermoplastic or thermoset material, the most suitable thermoplastic is poly(vinyl chloride) (PVC), which can be used as the matrix for compounding with different additives to produce materials with improved properties.
PVC is an easily processed, versatile, and low-cost polymer widely used in different industries (e.g., building, food packaging, medical devices, textile, toy manufacturing).Therefore, the recycling of waste PVC, as a thermoplastic, is possible with the application of appropriate technology and additives for the setting, especially plasticizers that affect both the processing and mechanical properties of PVCs.It can be compounded with various additives to obtain a diverse range of properties.PVC requires the addition of cost-effective plasticizers, e.g., traditional phthalate plasticizers (di(2-ethylhexyl) phthalate-DOP) [4], to provide good flexibility and permanence for the PVC product, as well as to remain competitive in the polymer market.Although phthalates show a favorable effect on PVC processing, they migrate easily from the PVC matrix and exhibit a subsequent loss in material properties, and, in conjunction with their harmful effect, they pose significant risks to both human health and the natural environment, i.e., toxicological and ecotoxicological threats, respectively [4].Therefore, the newest European regulative prohibits the use of phthalate plasticizers in PVC products for human use [5].This recognition of the adverse effects of phthalates underscores the urgent need for alternative solutions in the realm of plasticizers [6].
The use of phthalate-free and non-toxic plasticizers to replace phthalates containing them has become a research topic of great importance [7,8].Choosing a plasticizer with optimal structure and low environmental impact improves the properties, health safety, and CO 2 footprint of the recycled PVC products.The global market of commercial bio-plasticizers is segmented into four main groups: epoxidized soybean oil, castor oil, citrates, and succinic acid [9][10][11].Considering the fact that the bio-plasticizer market size is estimated at 446.29 kilotons in 2024, and is expected to reach 604.89 kilotons by 2029 [9], there are numerous opportunities to expand the assortment of green plasticizers.Mazitova et al. [10] conducted an ecological and economic assessment of the use of new adipate plasticizers in PVC composites.They confirmed the effectiveness of their use in accelerating biodegradation processes.The production and application of bio-plasticizers from renewable sources such as lactic acid, glycerol and succinate esters, and isosorbide are described in recent studies [11].In the current study, we consider the potential use of the waste poly(ethylene terephthalate) (PET) as raw material for the synthesis of "green" phthalate-free plasticizers for processing the waste PVC.
As one of the widespread thermoplastic polymers, PET is largely used in the food industry and for the preservation of beverages [12,13], in the automotive industry, and in packaging due to its favorable mechanical properties; high transparency; chemical stability; and good oxygen, carbon dioxide, and water-vapor barrier properties.However, it represents a significant ecological problem [14].These challenges are associated with the non-biodegradability and necessity of the development of proper PET recycling technologies, thus highlighting the complexity of the process and addressing financial aspects in key sectors of the economy [15][16][17].The pursuit of effective polymer recycling remains challenging and crucial for achieving sustainability goals and reducing reliance on finite fossil-based resources.Waste PET is relatively well recycled compared to other plastics, as one of the most successfully recycled polymers [1,18,19].Recycling processes include re-extrusion, mechanical, chemical, and energy recovery methods [20].The chemical recycling of PET involves various processes such as hydrolysis, alcoholysis, glycolysis, and aminolysis, producing oligomeric/monomeric products with different functionalities [21].The aim of chemical recycling is to convert the macromolecular structure of waste PET into specialty added-value chemicals and materials, promoting effective and environmentally friendly technology [22].Products resulting from PET glycolysis can serve as plasticizers and monomers in polymer synthesis (epoxy resins, unsaturated polyester, melamine formaldehyde and alkyd resins, polyurethane dispersions) [23,24].The plasticizers play a crucial role in reducing the viscosity and in easing the melt processing of polymers [25].
Combining multiple plasticizers has proven to be more effective in optimizing the properties of polymers [6].Creating novel plasticizers is a complex task that involves the consideration of various factors such as mechanical properties, low migration capability, simplicity of production, and cost-effectiveness.Recent studies indicate that high-molecular-weight plasticizers derived from renewable resources hold potential applications [26][27][28].Also, to address these issues, the incorporation of low-migration plasticizers can be a viable solution [14], and the potential of using waste PET glycolysates, which leads to improved processing capabilities and mechanical properties, could be a promising alternative [23,29,30].PET, when depolymerized by hydrazine monohydrate, exhibits potential as a secondary plasticizer [31].Furthermore, studies have demonstrated that the use of diethylene glycol terephthalate modified with maleic anhydride results in a material with commendable mechanical properties [30].Terephthalate-based plasticizers contribute to excellent product durability, flexibility at low temperatures, and enhanced electrical insulation capabilities [32]; thus, they hold promise as a viable and beneficial alternative.Therefore, if waste PET, a polyester-type thermoplastic polymer, and reactants of natural origin are used in plasticizer syntheses, an extraordinary situation is realized that includes the principles of green chemistry in technological processes.Moreover, this study provides a production process that unites two polymeric wastes, PET and PVC, in added-value materials, plasticizers and re-granulates, respectively.
The aim of this study was to test the applicability of a "green" plasticizer obtained by waste PET glycolysis (transesterification) using renewable reactive diol, i.e., propylene glycol (PG) terminated with bio-based levulinic acid (LA), as a substituent to commercial product DOTP.Accordingly, the main goals of the present study were related to the replacement of the commercial non-phthalate plasticizer DOTP in the production of PVC regranulates with synthesized "green" LA/PG/PET/EG/LA surrogate.In order to analyze influences of structural characteristics of the plasticizer, we performed a comparative study of the mechanical properties of the PVC-based materials, including LA/PG/PET/EG/LA plasticizers and that obtained in an analogous manner using DEG, instead of PG, to produce LA/DEG/PET/EG/LA.As a commercial counterpart, a non-phthalate DOTP plasticizer and diisononyl phthalate (DINP) were used in order to examine the influences of orthoversus para-substitution on the change in mechanical properties of the obtained materials.Additionally, the production of glycolysates and PET-based plasticizers was performed on a semi-industrial scale, followed by thorough plasticizer characterization.The developed optimal technology for PVC re-granulates production was applied, and further, derived PVC-based materials were comparatively tested in relation to their mechanical and physical properties, as well as their resistance to migration.The "green" LA/PG/PET/EG/LA plasticizers showed promising results that open the possibility for their application in the waste PVC recycling process in the production of commercially valuable re-granulates and derived products such as car mats, soles for slippers and shoes, floor covering, household equipment, agriculture auxiliary materials, and similar products.

Synthesis of Plasticizers Based on Waste PET Glycolysates
Plasticizer syntheses were performed at laboratory level, in the first phase, in order to develop optimal production technology, and subsequently transferred to a greatercapacity reactor to provide the required quantity for semi-industrial manufacturing of PVC re-granulates.
2.2.3.Synthesis of LA/PG/PET/EG/LA and LA/DEG/PET/EG/LA Plasticizers at the Laboratory Level: General Procedure The glycolysis was carried out in a high-pressure Parr reactor (Figure 1a) in which 76 g of PG (1 mol) or 106 g of DEG (1 mol) (performed in two distinct runs, Table 1), and 194 g of PET (1 mol) and 0.3 wt.% Fascat 4100 catalyst were added.Glycolysis was carried out for 6 h at 230 • C, producing DEG/PET/EG and PG/PET/EG precursors (Table 1).The hot precursors (~100 • C), PG/PET/EG or DEG/PET/EG, were transferred to three-necked round-bottom flasks equipped with a thermometer, mechanical stirrer, and Dean Stark separator.Further, bio-based LA (232 g, 2 moles) was added drop-wise for 15 min, and the reaction took place until more than 85% of the stoichiometrically reacted water was separated.At this point, TBT (0.3 wt.%) was added to promote an increase in the plasticizer yield to reach more than 97% of the theoretically calculated water separation.Synthesized raw plasticizers LA/DEG/PET/EG/LA (Plast 1) or LA/PG/PET/EG/LA (Plast 2) were subjected to vacuum (max 120 • C/1500 Pa) to remove water and low-boiling compounds, and collected product was yellowish viscous liquid (yield > 93% with respect to either isolated water or product weight in relation to DEG/PG reactants).Products can be used as obtained or purified by washing with 5% solution of sodium hydroxide and water, drying, and solvent distillation.The results of product characterization, obtained from the use of physicochemical, FTIR, and NMR methods, showed negligible differences in products, and thus both alternatives can be used in a PVC production technology (Scheme 1).Two alternative processes are defined with or without purification of plasticizer.From a techno-economical point of view, the process without plasticizer purification was used in the following study.Two alternative processes are defined with or without purification of plasticizer.From a techno-economical point of view, the process without plasticizer purification was used in the following study.Two alternative processes are defined with or without purification of plasticizer.From a techno-economical point of view, the process without plasticizer purification was used in the following study.The transesterification of waste PET (glycolysis) (1.94 kg, 10 mol) was carried out using PG (0.76 kg, 10 mol) (PG/PET/EG) or DEG (1.06 kg, 10 mol) (DEG/PET/EG) at a molar ratio of either 1:1 PET: DEG or PET: PG in a 10 L home-made laboratory reactor (Figure 1b).The reactor was equipped with an inlet for reactants, a discharge pipe for the gaseous mixture, a short column filled with a stainless-steel spring packing (a distillation of the excess of ethylene glycol and water from the system), and a thermometer.The reaction was carried out at 220-225 • C for 6 h, adding 0.3 wt.% Fascat 4100 catalysts and one of the glycols (closed system).After the glycolysis process, adding 2.32 kg (20 mol) of LA was followed by heating at 180 • C. The reaction took place until more than 85% of the theoretically calculated water was separated.At this point, TBT (0.3 wt.%) was additionally charged to promote an increase in the plasticizer yield to reach more than 97% of the theoretically calculated water separation.Synthesized raw plasticizers LA/DEG/PET/EG/LA (Plast 1) or LA/PG/PET/EG/LA (Plast 2) were subjected to vacuum (max 150 • C/1500 Pa) to remove water and low-boiling compounds.The collected products were light brownish viscous liquids (yield > 94% with respect to either the isolated water or the product weight in relation to DEG/PG reactants).The full characterization was provided using physicochemical, FTIR, and NMR methods.Reactors used for synthesizing plasticizers at the laboratory and semi-industrial levels are presented in Figure 1b.
Both plasticizers LA/DEG/PET/EG/LA (Plast 1) and LA/PG/PET/EG/LA (Plast 2) were synthesized at a quantity ~8 kg (from two batches) and used in the production of PVC re-granulates.

Production of PVC Re-Granulates Using Commercial and "Green" Plasticizers: General Method
Waste PVC (ground PVC material provided by RKS Kompoziti, Čelarevo, Serbia) was used at both laboratory and semi-industrial levels of PVC re-granulate production (Scheme 1).In the first instance, waste PET depolymerization provides glycolysates that can be used with purification (flow II) or directly in compounding with ground waste PVC (flow I) (Scheme 1).The process of compounding ground waste PVC with plasticizer and additives in hot and cold mixers followed by re-granulation was first optimized in a laboratory-level grinding mill (6 L) (Figure 2).as a meritorious parameter for the definition of optimal plasticizer content, and it was found that 20 wt.% was optimal (example tensile strength of PVC material with 20 wt.% of LA/PG/PET/EG/LA was 34 MPa), where variation around this median value, e.g., for the 0.5 wt.% step of plasticizer addition, causes small variations in the tensile strength value.Thus, final specimens produced at 20 wt.% plasticizer addition were used for physical and mechanical characterization, as well as plasticizer migration testing.Analogous procedure was also carried out using commercial DOTP and synthesized LA/DEG/PET/EG/LA plasticizers.In the second step, optimized technology was transferred to the semi-industrial level (performed using equipment owned by RKS Kompoziti Ltd., Čelarevo, Serbia).Briefly, ground PVC waste (20 kg) was processed at a semi-industrial level (Figure 3) using 4.25 kg of plasticizers (commercial or manufactured) according to optimized technology.The temperature of the processed material was adjusted using a boiler (Figure 3a) connected The ground waste PVC material (2.4 kg) was placed in a laboratory mixer with a system for either water heating or cooling to set the process temperature.
When the temperature was 35 • C, the plasticizer, at quantities of 10, 12.5, 15, 17, and 17.5 wt.% with respect to PVC, was added and mixed for 5 min at a specified speed (~2500 rpm).Also, the thermal stabilizer, antioxidant, carbon black, stearic acid, and acrylic process aid was charged (in total 5.5 wt.%).After, the mixture was gradually heated due to material friction and externally heated using hot water to attain a temperature increase of ~3 • C/min.When the temperature reached 115-120 • C, material was additionally homogenized for 10 min at 120 • C and then discharged into a cold mixer, where the pasty product was cooled to 45 • C and ground to obtain a granular product.Tensile strength was used as a meritorious parameter for the definition of optimal plasticizer content, and it was found that 20 wt.% was optimal (example tensile strength of PVC material with 20 wt.% of LA/PG/PET/EG/LA was 34 MPa), where variation around this median value, e.g., for the 0.5 wt.% step of plasticizer addition, causes small variations in the tensile strength value.Thus, final specimens produced at 20 wt.% plasticizer addition were used for physical and mechanical characterization, as well as plasticizer migration testing.Analogous procedure was also carried out using commercial DOTP and synthesized LA/DEG/PET/EG/LA plasticizers.
In the second step, optimized technology was transferred to the semi-industrial level (performed using equipment owned by RKS Kompoziti Ltd., Čelarevo, Serbia).Briefly, ground PVC waste (20 kg) was processed at a semi-industrial level (Figure 3) using 4.25 kg of plasticizers (commercial or manufactured) according to optimized technology.The temperature of the processed material was adjusted using a boiler (Figure 3a) connected to a duplicator as an integral part of the hot mixer (Figure 3b).The obtained materials were further used for re-granulate production using a tween-screw extruder (Figure 4), and the obtained products are given in Figure 5.

Characterization Methods
Details on used characterization methods are given in Supplementary Material S2.4.

Results and Discussion
The success of the stepwise process of the catalytic depolymerization of waste PET was confirmed using FTIR analysis, and the functionality determination of PET glycolysates and the subsequent esterification of glycolysates with LA were performed using FTIR and NMR techniques.The LA/DEG/PET/EG/LA analog with DEG was comparatively used to distinguish structural effects, i.e., the contribution of the ether linkage to mechanical property changes in PVC-based material.

Characterization Methods
Details on used characterization methods are given in Supplementary Material S2.4.

Results and Discussion
The success of the stepwise process of the catalytic depolymerization of waste PET was confirmed using FTIR analysis, and the functionality determination of PET glycolysates and the subsequent esterification of glycolysates with LA were performed using FTIR and NMR techniques.The LA/DEG/PET/EG/LA analog with DEG was comparatively used to distinguish structural effects, i.e., the contribution of the ether linkage to mechanical property changes in PVC-based material.There was no waste generated throughout the applied procedures, and the resulting product had no harmful product features and was ready for further use and ultimate product manufacture.Figure 5 depicts some colorful re-granulates obtained using the commercial master batch and current technology.
Additionally, the production of material based on PVC K70 and DOTP was performed in an analogous manner, and the results of mechanical testing are given in Table 2. 1 Oxygen percent was calculated as residual value of carbon and hydrogen to 100%.

Characterization Methods
Details on used characterization methods are given in Supplementary Material S2.4.

Results and Discussion
The success of the stepwise process of the catalytic depolymerization of waste PET was confirmed using FTIR analysis, and the functionality determination of PET glycolysates and the subsequent esterification of glycolysates with LA were performed using FTIR and NMR techniques.The LA/DEG/PET/EG/LA analog with DEG was comparatively used to distinguish structural effects, i.e., the contribution of the ether linkage to mechanical property changes in PVC-based material.

Results of the Functionality and Elemental Analysis
The results of hydroxyl value (HV), acid value (AV), and elemental analysis for synthesized glycolysates and plasticizers are given in Table 2.
The elemental analysis and HV results validated the proposed structures of both glycosylates and Plast 1 and Plast 2 (Figures 6 and 7).The presented results undoubtedly confirmed the success of PET depolymerization, considering a theoretically calculated hydroxyl value close to one and the results of NMR analysis. 13C NMR Characterization of Plast 1-LA/DEG/PET/EG/LA The results of the 1 H and 13 C NMR analysis (the most convenient structure with atom numbering is given in Figure 6) of the plasticizers based on the product of PET glycolysis with DEG esterified with LA (Plast 1) are as follows:

Results of 1 H and
1 H NMR (500 MHz, CDCl   The results of the 1 H and 13 C NMR analysis (the most convenient structure with atom numbering is given in Figure 6) of the plasticizers based on the product of PET glycolysis with DEG esterified with LA (Plast 1) are as follows:

FTIR Analysis of DEG/PET/EG and PG/PET/EG Glycolysates
Infrared absorption spectra of the PET glycolysis products are shown in Figure 8. Absorption bands associated with hydroxyl groups are observed in the 3399-3441 cm −1 region.The C-H stretching frequencies in the 2957-2875 cm −1 and 2975-2875 cm −1 ranges are assigned to asymmetric and symmetric methylene and methyl functional groups in DEG/PET/EG and PG/PET/EG, respectively.
The C-H bending frequencies of methylene groups are observed at 1407-1370 cm −1 (Figure 8) in both spectra, and the frequency of methyl groups from propylene glycol in the PG/PET/EG spectrum is observed at 1341 cm −1 (Figure S5).The strong band at 1711 cm −1 belongs to C=O stretching vibrations in the carboxyl group overlapped with the ester group, confirming the success of the transesterification reaction [37].The bands between 1605 and 1506 cm −1 and the peak at 1455 cm −1 are attributed to skeletal C=C stretching and bending vibrations of aromatic ring terephthalic units, respectively.The absorption bands in the region of 1262-1017 cm −1 are attributed to the -C-O-H stretching of glycols, the -C-  The results of the 1 H and 13 C NMR analysis of the plasticizers based on the PET glycolysis product with PG esterified with levulinic acid (LA) (the most convenient structure with atom numbering is given in Figure 7) are as follows:  4-oxopentanoyl)oxy)propyl) terephthalate or higher-condensed analogs with n = 3 and 4 terephthaloyl units (Figure 7) [36].The most convenient structure of the synthesized LA/PG/PET/EG/LA (Plast 2) plasticizer is given in Figure S7.The FTIR spectra of Plast 1 and Plast 2 plasticizers are shown in Figure 9. Bands from the inherent glycolysate structure and new ones from the LA modification were observed.Thus, a small shift in the position of vibrational methylene/methyl groups to higher wavenumbers was observed, and a slight decrease in intensity was also noticed.Further, the absence of stretching vibrations of hydroxyl groups, the presence of a doublet at 1408 cm −1 and 1366 cm −1 corresponding to C-H bending vibrations of methylene/methyl groups from LA (Figure S5), and the increased absorption of C=O groups indicate the successful reaction esterification between LA and glycolysates.In addition, in both spectra, two peaks at 1166 cm −1 and 1175 cm −1 of ether groups in the spectra of DEG/PET/EG and PG/PET/EG glycolysates, respectively (Figure 8), are increased and shifted to 1158 cm −1 (Figure 9) after esterification with LA (Figure S5).This suggested an involvement of hydroxyl groups in the synthesis of Plast 1 and Plast 2. Also, the FTIR spectra reveal a small decrease in bands associated with out-of-plane C=C stretching and C-H bending of the aromatic ring of terephthalic units.The C-H bending frequencies of methylene groups are observed at 1407-1370 cm −1 (Figure 8) in both spectra, and the frequency of methyl groups from propylene glycol in the PG/PET/EG spectrum is observed at 1341 cm −1 (Figure S5).The strong band at 1711 cm −1 belongs to C=O stretching vibrations in the carboxyl group overlapped with the ester group, confirming the success of the transesterification reaction [37].The bands between 1605 and 1506 cm −1 and the peak at 1455 cm −1 are attributed to skeletal C=C stretching and bending vibrations of aromatic ring terephthalic units, respectively.The absorption bands in the region of 1262-1017 cm

FESEM Analysis
The FESEM technique was used to investigate the morphology of the fracture surfaces in order to determine the homogeneity and material compactness of the re-granulated sample as influential parameters for the deterioration/improvement in the mechanical properties.The fracture structure of the PVC re-granulates with commercial plasticizers is not homogeneous, as illustrated in Figure 10a, which indicates material inhomogeneity with the presence of holes as a potential weakening point that can lead to fracture and poor mechanical performance.The fibers emerge as almost free-standing particles at the cross-sectional surface with contributions to material discontinuity.The presence of any impurity could act as a stress concentrator and be the initial point of material cracking.The low wetting of fibers means that during the application of force and breaking of the material, it helps in cracking dissipation with significant deformation of the material structure.The number and structure of these material irregularities, as can be observed in diverse shapes such as particles or fibers [40] and holes, are higher in the PVC material obtained using commercial plasticizer DOTP.It seems that cleavage fracture dominates with a significant micro-void coalescence causing the formation of larger holes due to higher material ductility (Figure 10a).These processes are of lower significance in PVC with Plast 1 showing an area with elements of brittle fracture surfaces (Figure 10b).On the other hand, the PVC-based material with the LA/PG/PET/EG/LA plasticizer (Plast 2) showed the highest material homogeneity due to effective fiber wetting, and, thus, local stress concentration is prevented (Figure 10c).Bands from the inherent glycolysate structure and new ones from the LA modification were observed.Thus, a small shift in the position of vibrational methylene/methyl groups to higher wavenumbers was observed, and a slight decrease in intensity was also noticed.Further, the absence of stretching vibrations of hydroxyl groups, the presence of a doublet at 1408 cm −1 and 1366 cm −1 corresponding to C-H bending vibrations of methylene/methyl groups from LA (Figure S5), and the increased absorption of C=O groups indicate the successful reaction esterification between LA and glycolysates.In addition, in both spectra, two peaks at 1166 cm −1 and 1175 cm −1 of ether groups in the spectra of DEG/PET/EG and PG/PET/EG glycolysates, respectively (Figure 8), are increased and shifted to 1158 cm −1 (Figure 9) after esterification with LA (Figure S5).This suggested an involvement of hydroxyl groups in the synthesis of Plast 1 and Plast 2. Also, the FTIR spectra reveal a small decrease in bands associated with out-of-plane C=C stretching and C-H bending of the aromatic ring of terephthalic units.

FESEM Analysis
The FESEM technique was used to investigate the morphology of the fracture surfaces in order to determine the homogeneity and material compactness of the re-granulated sample as influential parameters for the deterioration/improvement in the mechanical properties.The fracture structure of the PVC re-granulates with commercial plasticizers is not homogeneous, as illustrated in Figure 10a, which indicates material inhomogeneity with the presence of holes as a potential weakening point that can lead to fracture and poor mechanical performance.The fibers emerge as almost free-standing particles at the cross-sectional surface with contributions to material discontinuity.The presence of any impurity could act as a stress concentrator and be the initial point of material cracking.The low wetting of fibers means that during the application of force and breaking of the material, it helps in cracking dissipation with significant deformation of the material structure.The number and structure of these material irregularities, as can be observed in diverse shapes such as particles or fibers [40] and holes, are higher in the PVC material obtained using commercial plasticizer DOTP.It seems that cleavage fracture dominates with a significant micro-void coalescence causing the formation of larger holes due to higher material ductility (Figure 10a).These processes are of lower significance in PVC with Plast 1 showing an area with elements of brittle fracture surfaces (Figure 10b).On the other hand, the PVC-based material with the LA/PG/PET/EG/LA plasticizer (Plast 2) showed the highest material homogeneity due to effective fiber wetting, and, thus, local stress concentration is prevented (Figure 10c).The results from FESEM analysis confirmed that Plast 2 is the most convenient for real application as it contributes to better material processability and homogeneity, and its compatibility influences the improvement in the mechanical properties (Table 3).The results from FESEM analysis confirmed that Plast 2 is the most convenient for real application as it contributes to better material processability and homogeneity, and its compatibility influences the improvement in the mechanical properties (Table 3).

Mechanical Properties of PVC Product Obtained from Re-Granulates
The results of the influence of the structural characteristics and plasticizer content on the mechanical and physical properties of PVC materials are given in Table 3.Three materials, i.e., PVC re-granulates with the DOTP plasticizer (PVC#1), Plast 1 (PVC#2), and Plast 2 (PVC#3), were used for test specimen production.The added plasticizer in the course of PVC re-granulate production was 17.5 wt.%.The results of mechanical and physical property determination are given in Table 3.
All of the PVC materials developed have good mechanical properties, indicating that the use of waste PET and commercial and synthesized plasticizers in the production of PVC materials did not impair their mechanical performances or chemical stability.
Shore hardness testing was used to compare the indentation resistance of the tested specimens.Usually, results from hardness testing can be used for predicting polymer qualities as well; however, it is most typically employed to forecast mechanical performance [41].Because the PVC employed in this investigation falls within the category of softer materials, a Shore A scale was used.The hardness of samples PVC#2 and PVC#3 with plasticizers (Plast 1 and Plast 2) increased by 7.4% to 11.8%, respectively, with respect to the material with DOTP (PVC#1).
Additionally, the addition of Plast 1 and Plast 2 resulted in a transition from low medium-hard values to high medium-hard values (70-85), as well as an increase in tensile strength due to the higher carbonyl content compared to DOTP, resulting in stronger dipole-dipole interactions with the PVC chain [28,42,43].Furthermore, when compared to ortho-ester, i.e., a material with the DINP plasticizer (σ = 24.7 MPa), the structure with a para-substituted benzene ring in terephthalate diester moieties, i.e., DOTP, contributes to improved strength of the PVC re-granulate derived materials [44].These findings are consistent with the structures of plasticizers proposed by NMR and FTIR investigations.The addition of the PET plasticizer causes a negligible increase in the specific density of the re-granulates investigated.
The impact strength test was performed using the standard ASTM method for toughness determination (Charpy Method).It denotes the ability of the material to absorb energy during plastic deformation.Strong materials have high impact resistance, and their strength is the result of a combination of strength and ductility.The Charpy toughness of PVC#2 and PVC#3 increased by 10.3% to 20.7% with the addition of PET plasticizer.Higher elongation values in PVC re-granulates with Plast 1 and Plast 2 are generated by hydrogen bonding between ester carbonyl groups in plasticizers and the PVC backbone, which reduces polymer intermolecular interactions, resulting in enhanced chain segment mobility [44].
The mechanical properties of the material obtained from PVC re-granulates, which contain synthetized plasticizer LA/PG/PET/EFG/LA, are slightly lower than those of virgin PVC with commercial plasticizers.Specifically, for virgin PVC incorporated with 25% of the commercial DOTP plasticizer, the tensile strength measures 39 MPa, the modulus of elasticity is 252 MPa, the bending strength reaches 67.4 MPa, the Shore A hardness stands at approximately 78.2, and the impact strength records 4.57 kJ/m 2 (Table 3).

Migration Test
Plasticizer migration from the produced PVC materials was performed according to the International Standard Criteria (ISC) and compared to the reference sample under the hypothesis that the liquid commercial plasticizer, DOTP, is a migratory species.Table 4 shows the migration test results for the flexible PVC compounds.Because of the lower molecular size, the PVC samples containing Plast 1 and Plast 2 samples demonstrated reduced weight loss due to the greater carbonyl cohesive block moiety compared to DOTP [4].Due to the beneficial properties of the PVC#3 material, DSC and DMTA analysis were used for PVC#1 and PVC#3 materials.

Differential Scanning Calorimetry
During processing, gelation of PVC occurs, which strongly affects the physical properties of the final product [45].As the material is heated, the smaller "grains" (crystallites) melt first [46].While melting occurs, the grains combine to create a state of partial gelation.The extent of gelation is influenced by the processing temperature, with elevated temperatures resulting in a greater degree of gelation.Since Gilbert and Vyvoda [47] identified two endothermic peaks on DSC curves of processed PVC, and Potente [48] proposed Equation (1) to calculate the degree of gelation (G) using the melting enthalpies of primary (H A ) and secondary (H B ) crystallites, analysis of PVC gelation using DSC gained acceptance as a standard approach for examining processed PVC.
As shown in Figure 11, sample PVC#1 has one large and broad endothermic peak, while sample PVC#3 has two endothermic peaks, i.e., the PVC#1 sample is completely gelled, and PVC#3 has some portion of PVC that is not yet gelled.The interpeak temperature related to processing temperature is found at the onset of the second endothermic peak and has a value of 184 • C. The degree of gelation of sample PVC#3 determined according to Equation ( 1) is 98.4%.Furthermore, it is obvious that curves differ very much in shape and area; the melting enthalpy of sample PVC#1 is twice as large as the melting enthalpy of sample PVC#3.This indicates that between samples, there are large differences in morphological features, crystallite structures, and networks of forces.The strength of this network is recognized as a significant factor influencing the mechanical properties of PVC-based materials [45].
cording to equation 1 is 98.4%.Furthermore, it is obvious that curves differ very much in shape and area; the melting enthalpy of sample PVC#1 is twice as large as the melting enthalpy of sample PVC#3.This indicates that between samples, there are large differences in morphological features, crystallite structures, and networks of forces.The strength of this network is recognized as a significant factor influencing the mechanical properties of PVC-based materials [45].

Dynamic Mechanical Thermal Analysis
The DMTA results are illustrated in Figures 12 and 13.Below −50 • C, in a glassy state, free volume is not enough for the motion of chain segments.The storage moduli of samples are high and almost identical; failures during application in this temperature range are possible because the samples may be too rigid and brittle.With increasing temperature, the free volume and mobility of segments increase, friction between the chains causes the loss of more energy, and the loss modulus passes through the maximum [49][50][51][52]

Dynamic Mechanical Thermal Analysis
The DMTA results are illustrated in Figures 12 and 13.Below −50 °C, in a glassy state, free volume is not enough for the motion of chain segments.The storage moduli of samples are high and almost identical; failures during application in this temperature range are possible because the samples may be too rigid and brittle.With increasing temperature, the free volume and mobility of segments increase, friction between the chains causes the loss of more energy, and the loss modulus passes through the maximum [49][50][51][52].The maximum loss modulus corresponds to the glass transition temperature Tg, and it was found that the Tg of sample PVC#1 is −45 °C, and the Tg of sample PVC#3 is −48 °C.These results are in accordance with the Tg values which Langer et al. [30] obtained for PVC plasticized with 32 wt.% of different oligoester plasticizers.Above Tg, in the transition range, the moduli of PVC#1 sample fall abruptly for two orders of magnitude, while the moduli of the PVC#3 sample fall moderately, i.e., sample PVC#3 has a wide transition range that extends over 70 °C.
The rubber-elastic plateau of PVC#1 begins at a temperature of approximately −20 °C, and for PVC#3, it cannot be clearly distinguished from the transition range.Nevertheless, in this temperature range, motions of whole polymer chains are prevented by entanglements and physical interactions, which act as temporary networks between the macromolecules.Due to the stronger physical interactions in the PVC#3 sample, it has significantly better mechanical properties than PVC#1.Although above Tg, the PVC#3 sample has higher modulus values than the PVC#1 sample, Figure 13 shows that the PVC#3 loss factor has higher values than PVC#1 in the rubber elastic region.The higher loss factor of PVC#3 indicates that its ability to dissipate the applied energy is better compared to PVC#1, i.e., its damping characteristics are superior.The larger area under the loss factor curve signifies the extent of polymer chain mobility and, consequently, its impact resistance.Figure 13 also reveals that the curves ex-

Evaluation of the Successfulness of Sustainable Concept
An acceptable and simple method for evaluating the environmental acceptability of the developed technology is the calculation of the E factor (Supplementary Material S3.9) [54][55][56].In order to simplify the calculation, the complex technology was divided into three phases: the E-factor for the first phase was found to be 0.84, that for the second was 4.37, and that for the third was 0.074, which indicated the acceptability of the proposed technology in relation to environmental impact.The last step, i.e., PVC re-granulate production, does not generate wastewater or waste material, which can also be quantified with an E factor of 0. Improvement in the environmental impact, i.e., E factor decrease, can be achieved by designing the appropriate technology for wastewater treatment from LA, PG, and plasticizer production that would eliminate the negative influence on the environment.
On the other hand, the Life Cycle Assessment (LCA) concept can be considered.Raw material production is the first step in life cycle assessments (LCAs), which cover manufacturing, production, recycling, and end-of-life exhausted material disposal.To ascertain the environmental impact of PET bottle goods in terms of energy consumption and waste generation, Ncube and Borodin [57] conducted a life cycle assessment (LCA) on PET bottles.According to their investigation, Table S1 displays the environmental profile of a 1 kg PET bottle.Table S2 presents the equivalent categories for the years of 2011 and 2018, based on the production of 1000 kg of PET resin, along with the percentage change from the initial results for each category [58].The presented data indicate the necessity of the development of the technology for the efficient use of waste PET and transformation into new product.
The commercial solution in [59] is a proprietary economic and efficient technology for DOTP production from terephthalic acid (detail given in Supplementary Material) [59].No reaction time was offered, but according to other patent literature [60], eight hours was necessary to finish the esterification reaction.A higher energy consumption was realized by the application of current technology, but due to the use of waste PET as raw material, a two-fold-lower cost in relation to commercial terephthalic acid (PTA), and the use of 2-ethyl hexanol (2EH) as commercial raw materials in commercial technology justify the possible implementation of the technology developed in this work.
Overall, based on the reproducible results from the laboratory level of production of synthesized plasticizer LA/PG/PET/EG/LA (based on bio-and recycled sources) and The rubber-elastic plateau of PVC#1 begins at a temperature of approximately −20 • C, and for PVC#3, it cannot be clearly distinguished from the transition range.Nevertheless, in this temperature range, motions of whole polymer chains are prevented by entanglements and physical interactions, which act as temporary networks between the macromolecules.Due to the stronger physical interactions in the PVC#3 sample, it has significantly better mechanical properties than PVC#1.
Although above T g , the PVC#3 sample has higher modulus values than the PVC#1 sample, Figure 13 shows that the PVC#3 loss factor has higher values than PVC#1 in the rubber elastic region.The higher loss factor of PVC#3 indicates that its ability to dissipate the applied energy is better compared to PVC#1, i.e., its damping characteristics are superior.The larger area under the loss factor curve signifies the extent of polymer chain mobility and, consequently, its impact resistance.Figure 13 also reveals that the curves exhibit a single peak, indicating favorable compatibility between the plasticizers and PVC, resulting in homogeneous compounds [53].

Evaluation of the Successfulness of Sustainable Concept
An acceptable and simple method for evaluating the environmental acceptability of the developed technology is the calculation of the E factor (Supplementary Material S3.9) [54][55][56].In order to simplify the calculation, the complex technology was divided into three phases: the E-factor for the first phase was found to be 0.84, that for the second was 4.37, and that for the third was 0.074, which indicated the acceptability of the proposed technology in relation to environmental impact.The last step, i.e., PVC re-granulate production, does not generate wastewater or waste material, which can also be quantified with an E factor of 0. Improvement in the environmental impact, i.e., E factor decrease, can be achieved by designing the appropriate technology for wastewater treatment from LA, PG, and plasticizer production that would eliminate the negative influence on the environment.
On the other hand, the Life Cycle Assessment (LCA) concept can be considered.Raw material production is the first step in life cycle assessments (LCAs), which cover manufacturing, production, recycling, and end-of-life exhausted material disposal.To ascertain the environmental impact of PET bottle goods in terms of energy consumption and waste generation, Ncube and Borodin [57] conducted a life cycle assessment (LCA) on PET bottles.According to their investigation, Table S1 displays the environmental profile of a 1 kg PET bottle.Table S2 presents the equivalent categories for the years of 2011 and 2018, based on the production of 1000 kg of PET resin, along with the percentage change from the initial results for each category [58].The presented data indicate the necessity of the development of the technology for the efficient use of waste PET and transformation into new product.
The commercial solution in [59] is a proprietary economic and efficient technology for DOTP production from terephthalic acid (detail given in Supplementary Material) [59].No reaction time was offered, but according to other patent literature [60], eight hours was necessary to finish the esterification reaction.A higher energy consumption was realized by the application of current technology, but due to the use of waste PET as raw material, a two-fold-lower cost in relation to commercial terephthalic acid (PTA), and the use of 2-ethyl hexanol (2EH) as commercial raw materials in commercial technology justify the possible implementation of the technology developed in this work.
Overall, based on the reproducible results from the laboratory level of production of synthesized plasticizer LA/PG/PET/EG/LA (based on bio-and recycled sources) and related PVC re-granulates based on waste PVC at the semi-industrial level of production, they have good physical and mechanical properties, but these are lower in comparison to the material obtained from virgin PVC K70 and DOTP.These results indicate that the use of synthesized plasticizers in the production of PVC materials acts as plasticizers and reinforcing agents due to their oligomeric nature and wealth of present functional groups.

Conclusions
Waste-PET-based glycolysates were esterified using levulinic acid in order to produce a plasticizer for PVC re-granulate production using synthesized "green" PET-based plasticizers and waste PVC.NMR and FTIR techniques, as well as physicochemical methods, were used for the characterization of waste PET-based plasticizers.Manufactured-waste-PVC-based materials showed increased hardness, tensile strength, and elongation at break, which are consistent with the characterization results that indicate the significance of ester and keto carbonyl groups in the plasticizers, the ortho-versus para-position, and the intensities of dipole-dipole interactions of the PVC backbone (C-Cl dipole) and carbonyl group present in plasticizer.The lower migration in PVC compared to DOTP was also consistent with these findings, due to the higher number of terephthaloyl moieties.DSC analysis showed gelation with DOTP and LA/PG/PET/EG/LA plasticizer, at 98.4%, with morphological features, crystallite structures, and networks of forces.DMTA confirmed the better compatibility between the "green" plasticizer and PVC, resulting in a homogeneous structure of produced PVC re-granulates.
The results of the research presented revealed the potential of "green" plasticizer production, obtained by combining polymer recycling technology with the raw materials derived from bio-renewable resources, which would contribute to a reduction in carbon footprint as well as the reliance on fossil-based materials.Efforts towards sustainable waste management are essential to mitigate the environmental impact of plastic waste and move towards a more sustainable future.
writing-original draft preparation, M.M.V. and A.M.; writing-review and editing, M.M.V. and A.M.; visualization, J.G.; supervision, M.M. (Milutin Milosavljević) and A.M.; project administration, A.M. All authors have read and agreed to the published version of the manuscript.

Figure 3 .
Figure 3. Boiler for controlled heating of hot mixture (a), and hot mixer (b) (PVC high-speed mixer; 50 L) for blending of PVC with plasticizers and additives.Figure 3. Boiler for controlled heating of hot mixture (a), and hot mixer (b) (PVC high-speed mixer; 50 L) for blending of PVC with plasticizers and additives.

Figure 3 .
Figure 3. Boiler for controlled heating of hot mixture (a), and hot mixer (b) (PVC high-speed mixer; 50 L) for blending of PVC with plasticizers and additives.Figure 3. Boiler for controlled heating of hot mixture (a), and hot mixer (b) (PVC high-speed mixer; 50 L) for blending of PVC with plasticizers and additives.

Figure 5 .
Figure 5. (a,b) Assortment of PVC re-granulates.The final PVC product manufacturing process was carried out in the twin-screw extruder (Figure 4) regime: • The first zone-hold time 20 s; temperature 140 • C. • The second zone-30 s; temperature 180 • C. • The third zone-retention time 15 s; temperature 145 • C.

3. 3 .
FTIR Spectroscopy Results 3.3.1.FTIR Analysis of DEG/PET/EG and PG/PET/EG Glycolysates Infrared absorption spectra of the PET glycolysis products are shown in Figure 8. Absorption bands associated with hydroxyl groups are observed in the 3399-3441 cm −1 region.The C-H stretching frequencies in the 2957-2875 cm −1 and 2975-2875 cm −1 ranges are assigned to asymmetric and symmetric methylene and methyl functional groups in DEG/PET/EG and PG/PET/EG, respectively.Processes 2024, 12, x FOR PEER REVIEW 13 of 23 O-C-asymmetric/symmetric stretching of ether, and the -(C=O)-O-CH2stretching of ester groups [38].The out-of-plane bending vibrations of terephthalic units are shown by strong bands at 900-728 cm −1 [39].

Figure 8 .
Figure 8. FTIR spectra of the synthesized DEG/PET/EG and PG/PET/EG.
−1 are attributed to the -C-O-H stretching of glycols, the -C-O-C-asymmetric/symmetric stretching of ether, and the -(C=O)-O-CH 2 -stretching of ester groups [38].The out-of-plane bending vibrations of terephthalic units are shown by strong bands at 900-728 cm −1 [39].

Figure 9 .
Figure 9. FTIR spectra of the synthesized waste PET-based plasticizers.

Figure 10 .
Figure 10.The morphology of a cross-section of the obtained re-granulates with (a) commercial plasticizer DOTP and (b) synthesized Plast 1 and (c) Plast 2.

Figure 10 .
Figure 10.The morphology of a cross-section of the obtained re-granulates with (a) commercial plasticizer DOTP and (b) synthesized Plast 1 and (c) Plast 2.
. The maximum loss modulus corresponds to the glass transition temperature T g , and it was found that the Tg of sample PVC#1 is −45 • C, and the Tg of sample PVC#3 is −48 • C.These results are in accordance with the Tg values which Langer et al. [30] obtained for PVC plasticized with 32 wt.% of different oligoester plasticizers.Above T g , in the transition range, the moduli of PVC#1 sample fall abruptly for two orders of magnitude, while the moduli of the PVC#3 sample fall moderately, i.e., sample PVC#3 has a wide transition range that extends over 70 • C. Processes 2024, 12, x FOR PEER REVIEW 18 of 23

Figure 12 .
Figure 12.Storage modulus G′ and loss modulus G″ of sample PVC#1 (black curves) and PVC#3 (red curves) as a function of temperature.

Figure 12 .
Figure 12.Storage modulus G ′ and loss modulus G ′′ of sample PVC#1 (black curves) and PVC#3 (red curves) as a function of temperature.

Figure 13 .
Figure 13.The loss factor tan(δ) of sample PVC#1 (black curve) and PVC#3 (red curve) as a function of temperature.

Figure 13 .
Figure 13.The loss factor tan(δ) of sample PVC#1 (black curve) and PVC#3 (red curve) as a function of temperature.

Table 2 .
Results of HV and AV values, and elemental analysis of the synthesized glycolysates and plasticizers.
1Oxygen percent was calculated as residual value of carbon and hydrogen to 100%.

Table 2 .
Results of HV and AV values, and elemental analysis of the synthesized glycolysates and plasticizers.

Table 3 .
Mechanical and physical properties of the obtained PVC re-granulate.

Table 3 .
Mechanical and physical properties of the obtained PVC re-granulate.

Table 4 .
The results of migration tests of produced PVC materials.